The GE 90-30 series provides modular and reliable PLC solutions for legacy industrial applications. These controllers support flexible I/O configurations, ensuring long-term operational stability and smooth integration with existing automation systems.
GE 90-30 Series PLC
-
General Electric GE IC693MDL653 Series 90-30 32-Point 24VDC Input Module
Product Description The IC693MDL653 from GE Fanuc is a 32-point discrete input module designed for the Series 90‑30 PLC family. Supporting both positive (sourcing) and negative (sinking) logic, this module delivers flexible DC input integration for a variety of 24 V field devices. Its architecture features four isolated groups of eight inputs, each with two shared commons, providing partial isolation and enhanced noise immunity. Field connections are made via a 50‑pin high-density Honda-style connector, with optional pre-wired GE cables for simplified installation. The module does not include individual input status LEDs and can be mounted in any slot of a 5-slot or 10-slot Series 90‑30 baseplate. Technical Specifications Electrical Characteristics Rated Voltage: 24 VDC Input Voltage Range: 19.2–28.8 VDC (+10%, –20%) Input Current: 7.5 mA at rated voltage (average) On-State Voltage: ≥ 15 VDC Off-State Voltage: ≤ 6 VDC On-State Current: ≥ 4.5 mA Off-State Current: ≤ 2 mA Channel & Group Configuration Total Inputs: 32 points Groups: 4 groups of 8 inputs each Commons: 2 per group (internally tied) Logic Support: Positive and Negative Isolation: 1500 V between field side and logic side Response Times ON Response Time: ≤ 2 ms OFF Response Time: ≤ 2 ms Power Consumption Backplane Current Draw: 5 mA @ 5 VDC (16 inputs ON) Maximum Simultaneous Inputs ON: 16 recommended to maintain thermal limits Mechanical & Installation Connector: 50-pin high-density Honda connector Mounting: Any I/O slot in 5-slot or 10-slot Series 90‑30 baseplate Dimensions: 142 × 30 × 130 mm Weight: 0.30 kg Field Device Compatibility Pushbuttons Limit switches Proximity sensors Electronic switches Additional Notes No individual input status LEDs External 24 VDC field power required Pre-wired GE cables available for rapid installation Applications High-density 24 VDC discrete input acquisition Integration with PLC control in manufacturing lines Interface with sensors, switches, and low-power electronic devices FAQ Q: Can the module handle both sourcing and sinking devices?A: Yes, the IC693MDL653 supports positive (sourcing) and negative (sinking) logic inputs. Q: How many inputs can be active simultaneously?A: Up to 16 inputs ON are recommended to avoid thermal overload. Q: Does this module provide individual input LEDs for diagnostics?A: No, the IC693MDL653 does not include input status LEDs.
$200.00 $100.00
-
General Electric GE Fanuc IC693PBS201 PROFIBUS-DP Slave Module Series 90-30 PLC
Product Description The IC693PBS201 is a PROFIBUS-DP slave communication module for the GE Fanuc Series 90-30 PLC system. It allows the PLC to act as a slave device on PROFIBUS networks, exchanging data with external master controllers such as Siemens S7, ABB, or other DCS/SCADA systems. With support for high-speed communication up to 12 Mbps, it provides robust diagnostics and reliable data exchange in demanding industrial environments. Technical Specifications Specification Details Model IC693PBS201 Part Number IC693PBS201 Product Type PROFIBUS-DP Slave Module Series Series 90-30 PLC Communication Standard PROFIBUS DP-V0 compliant Data Exchange Capacity 244 bytes input, 244 bytes output Nominal Voltage 24 VDC Data Transmission Rate 9.6 kbps – 12 Mbps Communication Ports Two 9-pin D-sub connectors (1 PROFIBUS, 1 service port) Diagnostics Provides diagnostic information without bus access rights Protection Level IP20 Operating Temperature -40°C to +85°C Dimensions 130 × 35 × 100 mm Weight 0.55 lbs Mounting Any Series 90-30 baseplate except CPU slot 1 Status Information Slave Status Word Industrial Design Rugged construction for harsh environments Current Draw 450 mA @ 5VDC Key Features Integrates GE 90-30 PLCs into PROFIBUS DP networks with seamless communication. High-speed data transfer up to 12 Mbps for real-time process control. Interoperable with Siemens, ABB, and other PROFIBUS masters. Robust diagnostics provide detailed status and troubleshooting information. Industrial-grade reliability suitable for extreme temperatures and harsh conditions. Applications Manufacturing automation lines requiring PROFIBUS connectivity. Energy management and process control systems integrating legacy PLCs. SCADA or DCS systems where real-time bidirectional data exchange is needed. Extending the lifespan of GE 90-30 PLCs in modern automation networks. FAQ Q: Can IC693PBS201 communicate with Siemens or ABB masters?A: Yes, it is fully interoperable with Siemens, ABB, and other PROFIBUS DP masters. Q: What is the maximum data rate supported?A: Up to 12 Mbps for high-speed data transfer. Q: Can this module be mounted in any Series 90-30 baseplate?A: Yes, except in slot 1 of the CPU baseplate. Q: How many bytes can be exchanged?A: 244 bytes input and 244 bytes output for bidirectional communication. Q: Does it provide diagnostics?A: Yes, the module provides detailed diagnostic data without requiring bus access rights.
$200.00 $100.00
-
General Electric GE Fanuc IC690USB901 USB/SNP Programming Cable
Product Description The IC690USB901 is a USB-to-SNP interface cable designed for GE Fanuc Series 90-30 and 90-70 PLCs. It enables modern PCs to connect with legacy PLC systems for programming, monitoring, and diagnostics. The cable supports long-distance communication and ensures compatibility with current Windows operating systems, providing engineers with a reliable bridge between USB-only devices and older GE PLC hardware. Technical Specifications Specification Details Model IC690USB901 Part Number IC690USB901 Product Type USB/SNP Programming Cable Compatible PLC Series Series 90-30, 90-70, 90-20, 90-Micro Cable Length 3 meters Interface USB to SNP (15-pin PLC port) Max Communication Distance 1.5 km at 19200 bps Baud Rate 300 bps – 1 Mbps, auto-adaptive Data Format 7/8 data bits, 1/2 stop bits, odd/even/no parity Power Supply USB bus-powered (~50 mA) Indicators Two-color LED for send/receive status Operating Temperature -20°C to +75°C USB Compliance USB V1.1 and USB CDC V1.1 standards OS Compatibility Windows 2000, XP, 7, 10, 11 Software Compatibility CIMPLICITY ME V5.0 and above Cable Ends Molded USB and 15-pin male SNP connector Weight 2.0 lbs PC Limitation Only one IC690USB901 per PC supported Key Features Connects modern USB PCs with legacy GE Fanuc PLCs without additional drivers. Supports long-distance communication up to 1.5 km for industrial applications. LED indicators provide real-time data transmission status for diagnostics. USB bus-powered plug-and-play design requires no external power supply. Simulates traditional COM port for legacy software compatibility. Applications Online program edits and updates for Series 90-30/90-70 PLCs Diagnostics and monitoring in process control systems Maintenance of manufacturing and industrial machinery Ideal for engineers maintaining legacy PLC installations FAQ Q: Can I use multiple IC690USB901 cables on the same PC?A: No, only one cable per PC is supported to avoid communication conflicts. Q: Which Windows versions are compatible?A: Windows 2000, XP, 7, 10, and 11 are supported. Older systems such as WinNT4/95/98/Me/DOS are not supported. Q: What is the maximum communication distance?A: Up to 1.5 km at 19200 bps. Q: Are there alternative cables for other GE Fanuc PLC series?A: For Series 90-Micro or 90-20 PLCs, the IC690USB901 also provides full compatibility.
$200.00 $100.00
-
General Electric GE Fanuc IC693CHS399 5-Slot Remote Baseplate Series 90-30 PLC
Product Description The IC693CHS399 is a 5-slot remote baseplate designed for the GE Fanuc Series 90-30 PLC system. It provides modular expansion for distributed control networks, ensuring organized wiring and reliable field operation. This baseplate must be connected to a CPU and cannot function independently. Technical Specifications Specification Details Model IC693CHS399 Product Type Remote Baseplate Series Series 90-30 PLC Module Slots 5 available slots for I/O modules Isolation Built-in isolation between +5V logic supply and interface circuits Max Cable Length 700 feet (213 meters) for daisy-chained baseplates CPU Requirement Must be connected to a PLC CPU or compatible interface system Expansion Connector 25-pin female D-type I/O bus connector Rack Number Selection DIP switch configurable Weight 1.25 lbs Wiring Supports structured, organized wiring practices Key Features Ensures stable and reliable field operation for distributed I/O. Provides organized wiring to simplify installation and maintenance. Supports efficient system expansion without altering the CPU architecture. Reduces commissioning time with structured signal management. Applications Suitable for industrial automation systems requiring remote I/O modules: Manufacturing process control Modular PLC system expansion Distributed signal acquisition and field operation FAQ Q: Can the IC693CHS399 operate without a CPU?A: No, it requires connection to a CPU or compatible interface system. Q: What is the maximum cable distance for multiple baseplates?A: Up to 700 feet (213 meters) for daisy-chained baseplates. Q: How many I/O modules can this baseplate support?A: It provides 5 slots for Series 90-30 I/O modules. Q: Are there alternative models for larger expansion?A: Yes, IC693CHS398 and IC693CHS397 offer 8- and 12-slot configurations respectively.
$200.00 $100.00
-
General Electric GE IC693CHS393 10-Slot Remote Expansion Baseplate
Product Description The IC693CHS393 is a 10-slot remote expansion baseplate engineered for the GE Fanuc Series 90‑30 PLC platform. Designed to extend I/O capacity for distributed or remote systems, it provides nine slots for discrete, analog, or specialty I/O modules and one dedicated power supply slot. This module cannot operate independently and relies on a connection to a main CPU rack via a 25‑pin D-sub expansion port. Supporting cable lengths up to 700 ft (213 m), the IC693CHS393 enables flexible remote installations while maintaining high-speed, stable communication. Built-in isolation protects the system from ground loops and electrical noise, ensuring reliable performance in industrial, energy, water treatment, and process environments. Its compact design allows panel or DIN‑rail mounting, making it suitable for a wide range of distributed control applications. Technical Specifications Parameter Specification Model IC693CHS393 Manufacturer GE Fanuc / Emerson Product Line Series 90-30 Product Type Remote Expansion Baseplate Total Slots 10 (1 power supply, 9 I/O/option slots) CPU Slots None (non-CPU baseplate) Expansion Connector 25‑pin D-sub female Max Cable Distance 700 ft (213 m) to CPU Max Remote Baseplates 7 (CPU-dependent) Architecture Daisy-chain remote I/O expansion Internal Power Consumption 460 mA @ 5 VDC External Power Requires separate Series 90-30 power supply Isolation Built-in between logic supply and interface circuits Operating Temperature –20 °C to 70 °C Storage Temperature –40 °C to 85 °C Humidity 5–95% non-condensing Dimensions 10.43 × 5.12 × 5.59 in (W × H × D) Weight 4.63 lbs Mounting Panel or DIN‑rail Key Features & Advantages Expands remote I/O capacity for Series 90‑30 PLC systems Supports up to 700 ft cable length between CPU and remote base Nine module slots for flexible I/O configuration Built-in isolation reduces interference from ground loops and electrical noise Compatible with a wide range of GE discrete, analog, and specialty I/O modules Suitable for distributed control in industrial, utility, and process plants Applications Remote I/O expansion in manufacturing lines Process control skids and pump stations Water/wastewater treatment facilities Distributed control systems across large industrial sites FAQ Q: Can the IC693CHS393 operate independently?A: No, it must connect to a main CPU rack via a 25‑pin D-sub expansion connector. Q: How many I/O modules can be installed?A: Nine I/O or option modules, plus one dedicated power supply slot. Q: What is the maximum cable distance to the CPU?A: Up to 700 ft (213 m).
$200.00 $100.00
-
General Electric GE IC693CPU313 Series 90-30 Embedded Turbo CPU Baseplate Module
Product Description The IC693CPU313 is a compact embedded Turbo CPU integrated with a 5-slot baseplate, designed for the GE Fanuc Series 90‑30 PLC systems. Featuring an Intel 80188 processor running at 10 MHz, it delivers a rapid 0.6 ms scan rate per 1K Boolean instructions, making it ideal for small to mid-sized automation projects that require reliable discrete and analog control without additional expansion racks. This embedded CPU/baseplate combination includes 12 KB of user memory, supports up to 160 discrete inputs and 160 discrete outputs, and provides built-in SNP and SNP‑X serial communication for streamlined integration. Its simple architecture and minimal footprint make it suitable for compact control panels, while its proven reliability ensures widespread deployment in industrial, utility, and manufacturing environments. Technical Specifications Parameter Specification Model IC693CPU313 Manufacturer GE Fanuc / Emerson Product Line Series 90-30 Product Type Embedded Turbo CPU Baseplate Weight 1.26 lb Processor Intel 80188 Turbo CPU Clock Speed 10 MHz User Memory 12 KB Register Memory (%R) 1024 words Discrete Global Memory (%G) 1280 bits Internal Coils (%M) 1024 bits Temporary Coils (%T) 256 bits System Status Bits (%S) 128 bits Analog Inputs (%AI) 64 words Analog Outputs (%AQ) 32 words Discrete Inputs 160 points Discrete Outputs 160 points Total System I/O Up to 4000 points (system-dependent) Baseplate 5-slot embedded CPU baseplate (non-expandable) Communication 1 built-in serial port (via power supply connector) Supported Protocols SNP slave, SNP‑X slave LAN Options Ethernet, FIP, Profibus, GBC, GCM, GCM+ via modules Backplane Current Draw 430 mA @ 5 VDC Operating Temperature 0–60 °C (32–140 °F) Storage Temperature –40–85 °C Dimensions 122 × 82 × 60 mm Expansion None Lifecycle Status Discontinued / Legacy Controller Key Features & Advantages Integrated CPU and baseplate reduces system footprint Fast 0.6 ms scan per 1K Boolean instructions for rapid logic processing Supports up to 4000 I/O points in expanded systems Ideal for compact control panels with limited space Widely deployed legacy controller with proven reliability Built-in serial communication for SNP/SNP‑X protocols Applications Small-to-medium industrial automation systems Utility process control panels Manufacturing systems requiring discrete and analog I/O management Compact machine control where footprint and reliability are critical FAQ Q: How many I/O points can the IC693CPU313 handle?A: It supports 160 discrete inputs and 160 discrete outputs; system expansions allow up to 4000 points. Q: What is the typical scan rate of this CPU?A: 0.6 ms per 1K Boolean instructions. Q: Can this baseplate be expanded with additional slots?A: No, it is a fixed 5-slot embedded CPU baseplate without expansion.
$200.00 $100.00
-
General Electric GE IC693MDL640 Series 90-30 16-Point 24VDC Input Module
Product Description The IC693MDL640 is a 16-point positive logic input module designed for the GE Fanuc Series 90‑30 PLC platform. It provides reliable digital input acquisition for industrial control systems, ensuring high signal integrity and robust isolation between field inputs and logic circuits. Each input channel is rated for 0–30 VDC operation and can handle standard 24 VDC field devices. The module features 16 individual LEDs for real-time status monitoring and offers typical response times of 7 ms, allowing fast and accurate processing of control signals. Isolation between the field side and the logic side is rated at 1500 VAC RMS, protecting sensitive logic from electrical interference. This module is compact, lightweight, and suitable for use in harsh industrial environments where dependable digital input performance is required. Technical Specifications Parameter Specification Model IC693MDL640 Manufacturer GE Fanuc / Emerson Product Line Series 90-30 Product Type Digital Input Module Logic Type Positive Logic Number of Inputs 16 Rated Input Voltage 24 VDC Input Voltage Range 0–30 VDC Input Current 15–30 mA (typical) Isolation 1500 VAC RMS (field-to-logic) Power Consumption 5–120 V Response Time 7 ms typical Status LEDs 16, one per channel Weight 0.71 lbs Mounting Backplane installation Key Features & Advantages 16 fully isolated positive logic inputs for robust signal acquisition Individual LEDs for per-channel status and diagnostics Fast response time (~7 ms) for time-critical applications High-voltage isolation ensures protection against field-side transients Compatible with Series 90-30 PLC systems Lightweight and compact, simplifying panel integration Applications Machine automation and control systems Input monitoring for discrete sensors and switches Industrial control panels in manufacturing, packaging, and processing plants Upgrade or replacement module for Series 90-30 systems FAQ Q: What logic type does this module use?A: The IC693MDL640 operates using positive logic, compatible with standard 24 VDC industrial inputs. Q: How many inputs does it support?A: The module supports 16 individual digital inputs. Q: Can this module protect against electrical interference?A: Yes, it features 1500 VAC RMS isolation between field inputs and the logic side.
$200.00 $100.00
-
General Electric GE IC693BEM340 FIP Bus Controller Module
Product Description The IC693BEM340 is a high-performance FIP (Factory Instrumentation Protocol) Bus Controller designed for GE Fanuc Series 90‑30 PLC systems. It enables deterministic, high-speed communication between a Series 90‑30 PLC and FIP-compatible devices, including remote I/O racks, field control stations, and Series 90‑70 PLCs. This module installs directly into the PLC backplane and supports redundant FIP bus operation, ensuring reliable communication in mission-critical automation applications. Two 9‑pin FIP bus connectors provide dual-channel redundancy, while a 15‑pin RS‑485 serial port allows firmware updates and external configuration. Six front-panel LEDs provide real-time diagnostic status, including module health, bus activity, and transmit/receive signals. With software-configurable operation and no DIP switches or jumpers required, the IC693BEM340 simplifies deployment while maintaining high system reliability in demanding industrial environments. Technical Specifications Parameter Specification Model IC693BEM340 Manufacturer GE Fanuc / Emerson Product Type FIP Bus Controller Module PLC Compatibility Series 90‑30 Backplane Support Universal Backplane Slot Requirement 1 slot Weight 0.60 lb Backplane Current 1.2 A max Power Supply 24 VDC, 1 A FIP Bus Connectors 2 × 9‑pin male D‑sub, supports redundancy Serial Interface 15‑pin RS‑485 for configuration and firmware Supported Devices Series 90‑70 PLCs, Field Control Units, Remote Drops, Generic FIP devices LED Indicators Module OK, Run, Carrier Detect Ch.1/Ch.2, Transmit Enable Ch.1/Ch.2 Redundant Bus Support Yes, dual-channel FIP bus Operating Temperature –20 °C to +70 °C (typical) Storage Temperature –40 °C to +85 °C Humidity 5–95% non-condensing Certifications CE, UL Mounting Rack-mounted, vertical orientation Key Features & Advantages Interfaces Series 90‑30 PLCs with FIP serial bus networks Dual FIP connectors for redundant, high-reliability communication RS‑485 serial port enables firmware updates and configuration Six front-panel LEDs provide immediate diagnostic feedback Software-configurable operation with no physical switches needed Rack-mounted design supports universal backplane installation Applications Industrial process control requiring high-speed, deterministic communication Multi-rack PLC systems integrating Series 90‑30 and Series 90‑70 controllers Remote I/O monitoring and field control integration Systems where redundant communication and fault diagnostics are critical FAQ Q: Can the module operate without redundant FIP connections?A: Yes, it functions with a single FIP bus but dual connectors provide redundancy for critical applications. Q: How are firmware upgrades performed?A: Firmware can be upgraded via the 15‑pin RS‑485 serial port using GE’s configuration tools. Q: What is the maximum operating temperature?A: The module is rated for –20 °C to +70 °C operating temperature.
$200.00 $100.00
-
General Electric GE IC693ACC400 Expanded Battery Backup Module
Product Description The IC693ACC400 is a high-capacity battery backup module engineered for GE Fanuc Series 90‑30 and VersaMax PLC systems. It provides extended retention of CPU logic, register data, configuration settings, and real-time clock information during power interruptions, ensuring continuous system reliability in mission-critical industrial applications. Featuring a lithium high-capacity cell, this energy pack significantly outperforms standard CPU batteries, offering backup duration up to 3–5 years depending on operating temperature. Direct plug-in installation to the CPU battery port simplifies deployment, while LED indicators monitor battery health and charging status. Safety features include overcharge, short-circuit, and reverse-polarity protection. Ideal for environments with fluctuating temperatures, power plants, manufacturing lines, and process control systems, the IC693ACC400 ensures data integrity and prevents cold-start errors after outages. Technical Specifications Parameter Specification Model IC693ACC400 Manufacturer GE Fanuc / Emerson Product Type Expanded Battery Backup Module Compatible PLCs Series 90‑30, VersaMax (CPE305 / CPE310 / CPE302) Battery Type Lithium high-capacity cell (some variants Li‑ion or NiMH) Nominal Voltage 3.0–3.6 VDC Capacity 7.5–8.5 Ah Typical Backup Duration 3–5 years (temperature dependent) Recharge Time ~24 hours (rechargeable variants) Operating Temperature 0–60 °C Storage Temperature –20–70 °C Shelf Life Up to 5 years Dimensions 2.62 × 50 mm (diameter × height) Weight 0.29 lb Mounting On-module, rack or chassis compatible Connector Type Samtec IPD1‑04‑D‑K Cable IC695CBL001, 3 ft (0.91 m), PVC-insulated tinned copper LED Indicators Charging, Fault, Low Capacitance, Charged Compliance EU RoHS Directive 2011/65/EU Key Features & Advantages Provides long-duration memory retention for CPU logic and registers High-capacity lithium cell ensures stable voltage and reliable backup Preserves real-time clock and retentive data to prevent cold-start errors LED diagnostics for quick monitoring of battery health Direct plug-in installation for easy replacement without system disassembly Robust protection against overcharge, short-circuits, and reverse polarity Compatible with Series 90‑30 and VersaMax CPUs, including CPE302, CPE305, CPE310 Applications Mission-critical automation systems in power generation and manufacturing Process industries requiring reliable PLC memory retention Environments with electrical noise or fluctuating temperatures Systems where data integrity during outages is essential FAQ Q: How long does the backup last under normal operation?A: The IC693ACC400 provides 3–5 years of typical retention depending on temperature and usage. Q: Can this battery be installed without powering down the PLC?A: Yes, it supports plug-and-play replacement on the CPU battery port without rack disassembly. Q: Which PLCs are compatible?A: Series 90‑30 CPUs, including CPE302, CPE305, and CPE310, as well as VersaMax PLCs for memory and RTC backup.
$200.00 $100.00
-
General Electric GE IC693CBL302 I/O Bus Expansion Cable
Product Description The IC693CBL302 is a 15‑meter I/O bus expansion cable engineered for the GE Fanuc Series 90‑30 PLC system. Specifically designed as the final link in a daisy‑chain configuration, it connects the CPU baseplate to the last expansion or remote baseplate, ensuring reliable communication across long distances. Featuring an integrated 100‑ohm termination resistor, the IC693CBL302 eliminates the need for external terminators, maintaining signal integrity at the end of the bus. Its continuous EMI shielding and rugged industrial construction provide high noise immunity and stable data transmission in electrically harsh environments. This makes it ideal for distributed control systems and complex automation setups. Technical Specifications Parameter Specification Model IC693CBL302 Manufacturer GE Fanuc / Emerson Product Line Series 90‑30 Product Type I/O Bus Expansion Cable Cable Length 15 meters (50 ft) Usage End-of-chain cable for final expansion link Weight 3.75 lbs Conductor Gauge 24 AWG stranded Voltage Rating Up to 300 V AC/DC Current Capacity 1 A max Impedance 100 Ω nominal Data Rate Up to 10 Mbps Insulation Resistance >1000 MΩ @ 500 VDC Connectors Male 25‑pin D‑Sub on both ends Termination Built-in 100‑ohm resistor Shielding Continuous EMI shielding (>90% noise reduction) Operating Temperature –20 °C to 70 °C Storage Temperature –30 °C to 80 °C Humidity Up to 95% non-condensing Vibration Resistance 5–500 Hz, 5G Hot-Swap Not supported (power off required) Key Features & Advantages 15 m cable designed for long-distance bus expansion up to 213 m total system run Built-in termination resistor ensures signal integrity at the end of the chain Continuous EMI shielding provides high immunity against electrical noise Rugged construction minimizes wiring errors and maintains reliable communication Fully compatible with all major Series 90‑30 CPUs and remote expansion racks Ideal for distributed control systems and complex automation networks Applications End-of-line expansion for remote I/O racks Long-distance signal transmission in PLC systems Industrial environments requiring high EMI protection Distributed control and automation applications FAQ Q: Can the cable be installed while the system is powered?A: No, the IC693CBL302 must be installed with the system powered off to ensure safety. Q: Is this cable compatible with all Series 90‑30 CPUs?A: Yes, it supports CPUs 331–341 (up to 4 expansion cables) and CPUs 350–374 (up to 7 expansion cables). Q: Why does it include a termination resistor?A: The built-in 100‑ohm resistor maintains proper signal integrity at the end of the I/O bus.
$200.00 $100.00
-
General Electric GE IC693CBL301 Series 90-30 2-Meter I/O Bus Expansion Cable
Product Description The IC693CBL301 is a 2-meter (6-foot) Wye-type I/O Bus Expansion Cable for GE Fanuc / Emerson Series 90-30 PLCs and PACSystems RX3i platforms. It extends the CPU baseplate’s I/O bus to expansion or remote baseplates, supporting daisy-chain configurations. Its robust Belden 8107 twisted-pair construction combined with continuous foil-and-braid EMI shielding ensures reliable, noise-immune communication even in harsh industrial environments. The cable features a single 25-pin D-Sub male connector on one end and a dual 25-pin D-Sub connector (male + female) on the other, allowing chaining of multiple expansion racks and proper termination at the last rack. Factory-grade construction reduces wiring errors and simplifies system expansion. Key Technical Specifications Parameter Specification Model IC693CBL301 Manufacturer GE Fanuc / Emerson Product Line Series 90-30 Cable Type I/O Bus Expansion Cable (Wye/Y-type) Length 2 m (6–6.6 ft) Cable Construction Belden 8107 twisted-pair, 24 AWG tinned copper Shielding 100% continuous EMI shield (foil + braid) Nominal Impedance 100 Ω Voltage Rating 30 V AC/DC Current Rating 2 A per contact Temperature Rating –20°C to 80°C Weight 0.55 lbs Dimensions 263 × 58 × 28 mm Connector A Single 25-pin D-Sub male Connector B Dual 25-pin D-Sub (1 male + 1 female) Maximum Expansion Cables CPU 350–364: up to 7; CPU 331–341: up to 4 Max Expansion Distance 15 m (50 ft) to last expansion baseplate Max Remote Distance 213 m (700 ft) to last remote baseplate Termination Required at end of chain (IC693ACC307 or built-in in certain cables) System Compatibility Series 90-30 PLCs, PACSystems RX3i (with SBT module) Functional Highlights Reliable extension of I/O bus for Series 90-30 and RX3i systems Supports multi-rack daisy-chain expansion Industrial-grade shielding provides high immunity to EMI and electrical noise Plug-and-play D-Sub connectors simplify installation Rugged construction for harsh factory environments Typical Applications Expanding I/O capacity for GE Series 90-30 or PACSystems RX3i PLCs Connecting CPU baseplates to remote or additional expansion racks Retrofitting legacy PLC installations with minimal wiring errors High-integrity systems requiring shielded, noise-resistant connections FAQ Q: Can multiple IC693CBL301 cables be connected in series?A: Yes, up to 7 cables for CPU models 350–364 and up to 4 for CPUs 331–341, following expansion limits. Q: Is a terminator required?A: Yes, use IC693ACC307 at the last rack unless using cables with built-in termination. Q: What environments is this cable suitable for?A: Rated for –20°C to 80°C, suitable for industrial environments with EMI and vibration.
$200.00 $100.00
-
General Electric GE IC693MDL754 Series 90-30 32-Point DC Output Module
Product Description The IC693MDL754 from GE Fanuc (Emerson) is a 32-point DC sourcing output module designed for Series 90-30 and PACSystems RX3i PLC platforms. It provides two fully isolated groups of 16 outputs, allowing simultaneous operation at 12 VDC and 24 VDC. Each output can drive up to 0.75 A with fast switching, and built-in auto-recovery protection ensures reliable operation under short-circuit or overcurrent conditions. LED indicators offer real-time monitoring of output status and fault conditions. DIP switch configuration allows selection of default output behavior for enhanced system control. This module is engineered for industrial applications requiring robust DC output control, precise diagnostics, and fault-tolerant operation. Its compact form factor facilitates installation in tight control cabinets while maintaining high performance. Key Technical Specifications Parameter Specification Model IC693MDL754 Manufacturer GE Fanuc / Emerson Product Line Series 90-30 Module Type 32-point DC sourcing output Output Groups 2 isolated groups of 16 outputs Compatible Systems Series 90-30, PACSystems RX3i Dimensions 142 × 30 × 130 mm Weight 0.49 lbs Rated Voltage 12/24 VDC nominal Voltage Range 10.2–30 VDC Output Type Positive logic (sourcing) Output Current 0.75 A per point Inrush Current 3 A for 10 ms (no ESCP trip) Overcurrent Trip ~5 A typical per point Leakage Current ≤0.1 mA Voltage Drop ≤0.3 VDC Backplane Power 300 mA @ 5 VDC External Supply Current 72–132 mA per group Protection Short-circuit, overcurrent, overtemperature (auto-recovery) Status Indicators 32 LEDs (Green = ON, Yellow = Fault) Response Time ≤0.5 ms Thermal Derating Required above 42°C at 30 VDC load Isolation 1500 VAC, 1 minute (field ↔ backplane, group ↔ group) Operating Temp 0°C to 60°C Storage Temp –40°C to 85°C Functional Highlights 32 sourcing outputs capable of driving DC loads Two isolated groups for mixed-voltage operation Auto-recovery protection enhances reliability Configurable DIP switch allows Force Off or Hold Last State Terminal block detection prevents wiring errors Fast on/off response suitable for high-speed control Typical Applications DC output control for manufacturing automation Expanding Series 90-30 or RX3i PLC output capacity Systems requiring fault-tolerant, high-speed switching Cabinet installations with mixed 12/24 VDC loads FAQ Q: Can the IC693MDL754 handle both 12 VDC and 24 VDC outputs simultaneously?A: Yes, each isolated output group can operate at a different DC voltage, allowing mixed-voltage applications. Q: What happens if an output is short-circuited?A: The module features auto-recovery protection and will resume normal operation once the fault is cleared. Q: How are faults indicated?A: 32 LEDs provide status feedback—green for active outputs, yellow for faults.
$200.00 $100.00
-
General Electric GE IC693CBL300 Series 90-30 I/O Bus Expansion Cable
Product Description The IC693CBL300 from GE Fanuc (now Emerson Automation) is a factory-assembled I/O bus expansion cable engineered for Series 90-30 PLC systems. Designed with a Y-configuration, it enables seamless communication between a primary CPU baseplate and additional expansion or remote racks. With its fully shielded twisted-pair construction, this cable ensures consistent signal transmission and resistance to electromagnetic interference, making it suitable for electrically noisy industrial environments. The 1-meter length is optimized for cabinet-level interconnections, reducing installation complexity while maintaining signal integrity. Key Technical Specifications Parameter Specification Model IC693CBL300 Manufacturer GE Fanuc / Emerson Product Series Series 90-30 Cable Type I/O Bus Expansion Cable (Wye / Y-type) Length 1 m (3.3 ft) Conductor 24 AWG tinned copper (twisted pair) Cable Type Reference Belden 8107 equivalent Shielding Dual-layer (foil + braid, full coverage) Connector A 25-pin D-Sub male Connector B Dual 25-pin D-Sub (1 male + 1 female) Voltage Rating 30 V AC/DC Current Rating 2 A per contact Impedance 100 Ω nominal Insulation Resistance ≥10 MΩ Dielectric Strength 2000 V Propagation Velocity ~70% Operating Temperature -25°C to +85°C Weight 0.24 lbs System Compatibility Series 90-30 PLC, RX3i (via SBT module) Lifecycle Status Obsolete / Legacy (available via surplus channels) Functional Overview The IC693CBL300 serves as a communication bridge within the PLC I/O architecture: Extends the I/O bus from the CPU rack to additional baseplates Supports multi-rack configurations using a daisy-chain topology Transfers both control data and bus power across connected racks Maintains signal stability in high-noise environments due to full shielding System expansion limits depend on the CPU type, typically supporting multiple racks within defined cable distance constraints. Installation & System Considerations Maximum distance for local expansion racks: up to 15 meters total Remote rack configurations can reach up to approximately 213 meters Requires external bus termination (e.g., IC693ACC307) when not integrated Recommended for use with factory cables to avoid signal mismatch or wiring errors Typical Applications Expansion of PLC I/O capacity in manufacturing lines Distributed control systems requiring multiple baseplates Retrofit or maintenance of legacy GE Series 90-30 installations Control cabinets where short, reliable interconnects are needed FAQ Q: Can this cable be used with newer Emerson RX3i systems?A: Yes, but only when used with a Serial Bus Transmitter (SBT) module to interface with the RX3i platform. Q: Is this cable suitable for long-distance communication?A: For short cabinet-level connections, it is ideal. For longer distances, ensure total bus length complies with system limits. Q: Does the cable include termination?A: No, an external terminator is required unless termination is integrated elsewhere in the system.
$200.00 $100.00
-
General Electric GE Fanuc IC693BEM341 2.5 MHz FIP Bus Controller Series 90‑30
Product Description The IC693BEM341 is a high-performance FIP (Factory Instrumentation Protocol) Bus Controller designed for GE Fanuc Series 90‑30 PLCs. This single-slot module delivers deterministic, high-speed communication at 2.5 MHz between the PLC and distributed FIP network devices, including I/O blocks, drives, controllers, and remote PLCs. Equipped with two 9‑pin FIP network ports and an RS‑485 port for firmware upgrades, the module supports operational Modes 11, 20, and 30. These modes enable redundancy management, slave-device monitoring, synchronous messaging, and Boolean time-stamping for up to 1024 values. Front-panel LEDs provide real-time diagnostics including module status, RUN state, carrier detection (CD1/CD2), and transmission enable (TEN1/TEN2), simplifying troubleshooting and system monitoring. Key Features High-speed FIP communication at 2.5 MHz Single-slot installation in Series 90‑30 baseplates Two 9-pin D-shell FIP connectors for network devices RS‑485 port for firmware upgrades Supports operational Modes 11, 20, 30 with redundancy and synchronous messaging Boolean value time-stamping for advanced data logging Compatible with Series 90‑30 CPUs (firmware 8.10+) and Series 90‑70 PLCs Front-panel LEDs: Module OK, RUN, CD1/CD2, TEN1/TEN2 Technical Specifications Communication Protocol: Factory Instrumentation Protocol (FIP) Fixed Data Rate: 2.5 MHz Ports: Two 9-pin D FIP connectors; One RS‑485 port Supported Modes: 11, 20, 30 (DIP-switch configurable) Functions: Redundancy, slave-device monitoring, synchronous messaging, Boolean time-stamping Electrical Backplane Power: Typical 800 mA @ 5 VDC; Maximum 1.2 A @ 5 VDC Slot Width: Single-slot Indicators LEDs: Module OK, RUN, CD1, CD2, TEN1, TEN2 Mechanical Dimensions: 100 × 127 × 60 mm (typical) Weight: 0.75 lbs Mounting: Slot 1 of Series 90‑30 baseplate Environmental Operating Temperature: 0–55 °C Storage Temperature: –25–70 °C Humidity: 5%–95% non-condensing Vibration: 0.2-inch displacement (5–10 Hz) Ingress Protection: IP20 Applications Distributed I/O networks for PLC systems CNC and servo drive integration Redundant control system architectures High-speed deterministic data exchange Multi-controller synchronization and monitoring FAQ Q: Can this module support redundancy?A: Yes, operational Modes 20 and 30 allow redundant network setups and fault-tolerant operation. Q: What devices are compatible with IC693BEM341?A: Compatible with Series 90‑30 CPUs (firmware 8.10+), Series 90‑70 PLCs, I/O blocks, drives, and FIP-enabled control devices. Q: How is firmware updated?A: Via the RS‑485 port on the module, using supported configuration tools. Q: What is the maximum number of Boolean values supported for time-stamping?A: Up to 1024 Boolean values can be time-stamped for logging and diagnostics.
$200.00 $100.00
-
General Electric GE Fanuc IC693MDL732 8-Point 12/24 VDC Output Module Series 90‑30
Product Description The IC693MDL732 is a DC output module for the GE Fanuc Series 90‑30 PLC family, providing 8 discrete positive logic outputs in a single module. It is designed for sourcing current to field devices, enabling reliable operation of relays, solenoids, lamps, indicators, and motor starters. Each output point is equipped with a dedicated LED status indicator, offering clear visual feedback. The module features full optical isolation between the logic circuitry and field side, ensuring robust noise immunity and protecting both the PLC and connected devices. Its compact design allows installation in any standard Series 90‑30 baseplate slot. Key Features 8 positive logic (sourcing) DC outputs with a shared common terminal Supports 12–24 VDC loads with 0.5 A per point and 2 A per common terminal Inrush handling: 4.78 A for 10 ms Full optical isolation (1.5 kV) between field and logic sides Dedicated green LED indicators for each output point Fast switching response: ≤ 2 ms on/off Compact single-slot design for Series 90‑30 baseplates Blue low-voltage label for easy identification Technical Specifications Electrical Rated Voltage: 12/24 VDC Output Voltage Range: 12–24 VDC (+20%, –15%) Outputs: 8 discrete points (one group) Maximum Output Current: 0.5 A per point, 2 A per common Inrush Current: 4.78 A (10 ms) Voltage Drop: ≤ 1 V Off-State Leakage: ≤ 1 mA Response Time: ≤ 2 ms (on/off) Isolation: 1.5 kV between field and logic Indicators 8 green LEDs for individual output status Arranged in two rows labeled A1–A8 and B1–B8 Mechanical Dimensions: 150 × 100 × 70 mm Weight: 1.7 lbs Country of Origin: USA Terminal Block: Removable for easy field wiring Environmental Operating Temperature: 0–60 °C Storage Temperature: –40–85 °C Humidity: 5–95% non-condensing Vibration: 5–2000 Hz @ 1 g Installation & Compatibility Fits any I/O slot on 5‑slot or 10‑slot Series 90‑30 baseplates No onboard fuses required Blue-coded low-voltage identification Compatible with GE Fanuc Series 90‑30 PLCs Applications Factory automation and process control Material handling and conveyor systems Water treatment control systems Oil & gas wellhead automation Auxiliary control of DC relays, solenoids, lamps, and motor starters FAQ Q: Can IC693MDL732 handle inductive loads like solenoids?A: Yes, it supports DC solenoids, relays, and motor starters with inrush up to 4.78 A for 10 ms. Q: Does the module require external fuses?A: No, the module is designed to operate safely without external fuses, relying on its internal protection and isolation. Q: How is output status monitored?A: Each output has a dedicated green LED that displays real-time ON/OFF status for clear diagnostics. Q: What is the response time for switching?A: Both ON and OFF switching times are ≤ 2 ms, ensuring fast and precise control of field devices.
$200.00 $100.00
-
General Electric GE Fanuc IC693TCM302 8-Channel Temperature Control Module
Product Description The IC693TCM302 is an 8-channel Temperature Control Module (TCM) designed for the GE Fanuc Series 90‑30 PLC. It combines precise thermocouple measurement with PWM relay output control, enabling both closed-loop PID and open-loop temperature regulation across eight independent zones in a single slot. This module supports multiple thermocouple types, features automatic cold-junction compensation, and provides comprehensive diagnostics including open-thermocouple detection, reverse-polarity protection, and out-of-tolerance alarms. Its high-speed PWM outputs allow efficient control of heaters, ovens, and other temperature-dependent processes. Key Features 8 independent thermocouple input channels with 12-bit resolution PWM relay outputs per channel for precise temperature control Closed-loop PID and open-loop manual control modes Automatic cold-junction compensation for accurate measurements Comprehensive diagnostics: open thermocouple, reverse polarity, out-of-tolerance alarms Front-panel LED indicators: PWR, RUN, FAULT, SHORT, plus 8 output status LEDs Single-slot installation in Series 90‑30 baseplates Technical Specifications Inputs Channels: 8 thermocouples Supported Types: J, K, L (some models R, S, B, T, E, N) Resolution: 12-bit (~0.2 °C) Accuracy: ±1 °C with auto-calibration Temperature Ranges: J: 0–450 °C K: 0–600 °C L: 0–450 °C Thermocouple Impedance: Max 30 Ω Cold Junction: 1 RTD channel or external reference Outputs Channels: 8 PWM relay outputs Voltage: 18–30 VDC Load Current: 100 mA per channel Off-State Leakage: 0.1 mA max PWM Period: 0.1–60 s programmable Overload Threshold: 700 mA typical (≥2 ms) Power Requirements Backplane Power: 150 mA @ +5 VDC External Power: 18–36 VDC for outputs (2.5 A inrush) Internal Fuse: 2 A, 125 V Mechanical & Environmental Dimensions: 127 × 76.2 × 152.4 mm (5 × 3 × 6 in) Weight: 0.24 lbs Mounting: Single-slot Series 90‑30 baseplate Operating Temp: 0–55 °C Storage Temp: –40–85 °C Humidity: 5–95% non-condensing Protection Class: IP20 Applications Multi-zone industrial temperature control Plastics molding and extrusion Ovens, kilns, and furnaces Packaging and sealing machinery Food processing and precise thermal regulation FAQ Q: Can the IC693TCM302 handle all thermocouple types?A: It supports J, K, L thermocouples natively; related models may support R, S, B, T, E, N types. Q: How is temperature output controlled?A: Each channel uses PWM relay outputs, configurable for 0.1–60 s periods, suitable for heaters or valves. Q: Can this module operate in open-loop mode?A: Yes, open-loop manual control is supported alongside PID closed-loop control. Q: What diagnostics are included?A: Detects open thermocouples, reverse connections, out-of-tolerance conditions, and output shorts.
$200.00 $100.00
-
General Electric GE Fanuc IC693BEM320 Series 90‑30 I/O LINK Slave Interface Module
Product Description The IC693BEM320 is a dedicated I/O LINK Interface Module (Slave) for the GE Fanuc Series 90‑30 PLC family. Designed for high-speed serial communication, it connects a Series 90‑30 PLC to a Fanuc I/O LINK master, commonly found in Fanuc CNC systems or Series 90‑70 PLCs. The module functions strictly as a slave, enabling deterministic I/O exchange for critical automation tasks. Configuration is straightforward, with an internal jumper allowing selection between 32-point or 64-point I/O operation. Multiple IC693BEM320 modules can operate on the same network (up to 16 slaves per master), making it ideal for distributed control and CNC integration. Key Features Slave-only I/O LINK interface for high-speed serial communication Jumper-selectable I/O capacity: 32 or 64 points Supports up to 16 slave devices per I/O LINK master Dual communication ports: RS‑485 and RS‑422 Front-panel LED indicators for module status (OK) and readiness (RDY) Backplane-powered (5 VDC), occupies a single slot Compact design: 64 × 127 × 102 mm, weight approx. 0.31 kg Technical Specifications Functional Overview Function: I/O LINK serial interface (slave) Supported PLCs: GE Fanuc Series 90‑30, Series 90‑70 Network: Fanuc proprietary I/O LINK Max Slaves: 16 per network (1 master + up to 16 slaves) Communication Ports: 2 Port Types: RS‑485, RS‑422 Purpose: High-speed data exchange with I/O LINK master Indicators LEDs: OK (powered/functioning), RDY (module ready/active) Electrical Power Supply: 5 VDC from PLC backplane Backplane Slots Required: 1 Mechanical Dimensions: 64 × 127 × 102 mm (alternate: 11.2 × 6.5 × 11 cm) Weight: 0.64 lbs Origin: USA Environmental Operating Temperature: 0°C to 60°C (32°F to 140°F) Humidity: 5–95% non-condensing Recommended: Climate-controlled enclosure for harsh environments Applications Fanuc CNC system integration with Series 90‑30 PLC Distributed I/O systems requiring fast and reliable communication PLC-to-CNC deterministic I/O exchange Industrial automation projects demanding high-speed serial interface FAQ Q: Can the IC693BEM320 operate as a master module?A: No, this module functions strictly as a slave device. Q: How do I select the I/O capacity?A: Use the internal jumper to choose either 32-point or 64-point operation. Q: How many IC693BEM320 modules can I use on one network?A: Up to 16 slave modules can be connected to a single I/O LINK master. Q: Which PLCs are compatible with this module?A: Series 90‑30 and Series 90‑70 GE Fanuc PLCs.
$200.00 $100.00
-
General Electric GE Fanuc IC693APU302 Series 90‑30 2-Axis Motion Positioning Module
Product Description The IC693APU302 is a high-performance 2-axis Axis Positioning Module (APM) for the GE Fanuc Series 90‑30 PLC platform. It integrates intelligent servo control with PLC logic execution, enabling precise, synchronized motion for applications requiring multi-axis coordination. The module operates in Standard Mode for full motion control with PLC logic or Follower Mode for electronic gearing in master/slave configurations. Designed for direct communication with servo drives and machine hardware, the IC693APU302 offloads motion control tasks from the CPU, improving system performance and responsiveness. Its flexible programming, high-resolution feedback, and configurable I/O make it suitable for packaging, labeling, pick-and-place, and CNC-style motion control. Key Features Supports 2 independent motion axes with high-resolution control Standard Mode for full motion control + PLC logic Follower Mode for synchronized electronic gearing Servo loop update rate: 2 milliseconds High-resolution positioning: ±8,388,607 user units Velocity and acceleration ranges up to 8,388,607 and 134,217,727 user units/sec² Non-volatile memory stores up to 10 motion programs, including “Program Zero” Front panel 24-pin high-density connectors for axes; additional communication port Supports A-Quad-B encoder feedback up to 175 kHz LED indicators: EN1, EN2, STAT, OK, CFG Technical Specifications Motion Control Axes: 2 independent Operating Modes: Standard, Follower Servo Loop Update: 2 ms Block Processing Time: < 5 ms Position Resolution: ±8,388,607 user units Velocity Range: 1–8,388,607 user units/sec Acceleration Range: 1–134,217,727 user units/sec² Programming & Configuration Software: Logicmaster 90‑30, VersaPro Instruction Set: High-level motion commands Motion Programs: Up to 10 stored in non-volatile memory Connectivity & I/O Axis Connectors: 2 × 24-pin high-density Communication Port: 9- or 25-pin depending on revision Compatible Cables: IC693CBL311, IC693CBL319, IC693CBL317, IC693CBL320 Terminal Block: Weidmuller RD25 910648 or equivalent Analog Outputs: ±10 V velocity command Analog Inputs: 12-bit signed feedback Digital Inputs: Home switch, overtravel limits, 8 user-defined inputs Digital Outputs: 4 user-defined outputs CPU & System Compatibility Supported CPUs: Embedded (311, 313, 323), Modular (331+) Max Modules: 3 APM per embedded CPU, 8 per modular CPU (max 3 per baseplate) Installation: Any Series 90‑30 CPU, expansion, or remote baseplate Physical & Electrical Dimensions: 64 × 127 × 102 mm Weight: 0.57 lbs Slot Width: Single-slot Current Draw: 800 mA @ 5 VDC Environmental Operating Temperature: Industrial range Feedback Support: Encoder A-Quad-B up to 175 kHz Applications Multi-axis servo control High-speed packaging and labeling machinery Pick-and-place systems Electronic gearing and synchronized motion CNC-style precision positioning FAQ Q: How many axes can the IC693APU302 control simultaneously?A: The module supports 2 independent motion axes. Q: What modes of operation are available?A: Standard Mode for full motion control with PLC logic and Follower Mode for electronic gearing. Q: Which CPUs are compatible with this module?A: Embedded CPUs 311, 313, 323, and modular CPUs 331 and higher. Q: Can it handle high-resolution motion?A: Yes, with ±8,388,607 user units of positional resolution and high-speed servo loop updates.
$200.00 $100.00
-
General Electric GE Fanuc IC693CBL303 Series 90‑30 Programmer & Converter Cable
Product Description The IC693CBL303 is a dedicated programming and converter cable for the GE Fanuc Series 90‑30 PLC family. It serves as the primary interface between the IC693PRG300 Hand-Held Programmer (HHP) and the PLC’s 15‑pin serial port, providing reliable communication, power delivery, and automatic detection of the programmer. This cable also facilitates connection between the PLC’s RS‑422/RS‑485 ports and the IC690ACC900 RS‑232 converter, allowing flexible field programming, monitoring, and maintenance. Built with industrial-grade shielding and connectors, it ensures consistent signal integrity in harsh environments. Key Features Directly connects IC693PRG300 HHP to Series 90‑30 PLCs Supplies power to the HHP via internal conductors Automatically signals the PLC that a programmer is attached Supports connection to IC690ACC900 RS‑232 converter EMI/RFI-shielded construction for industrial environments Plug-and-play with standard 15‑pin D-sub connectors Ideal for field programming, diagnostics, and maintenance Technical Specifications Cable Construction Cable Type: Belden 9508 shielded cable Conductor Size: 24 AWG (0.22 mm²), stranded copper Shielding: EMI/RFI protection Connectors Connector Type: Canon DA15S (15‑pin male D‑Sub) Connector Hood: AMP 207470‑1 Hardware Kit: AMP 207871‑1 (includes screws and clips) Electrical & Power Voltage Rating: Up to 30 VDC Current Capacity: 1 A per conductor Power to HHP: Yes (via cable) Physical & Mechanical Cable Length: 6 ft (2 m) Weight: 0.96 lbs Color: Gray Country of Origin: USA Environmental Ratings Operating Temperature: 0°C to 60°C Humidity: 5–95% non-condensing Applications Field programming of Series 90‑30 PLCs HHP-to-PLC communication Connecting PLC RS‑422/RS‑485 ports to RS‑232 converters Industrial automation maintenance and diagnostics FAQ Q: Does this cable supply power to the Hand-Held Programmer?A: Yes, the IC693CBL303 provides power to the IC693PRG300 HHP through its internal conductors. Q: Can it connect the PLC to an RS‑232 converter?A: Yes, it supports RS‑422/RS‑485 to RS‑232 conversion with the IC690ACC900. Q: Is it suitable for harsh industrial environments?A: Yes, it uses EMI/RFI-shielded construction and robust D-sub connectors for reliable field use.
$200.00 $100.00
-
General Electric GE Fanuc IC693PRG300 Series 90‑30 Hand-Held Programmer HHP
Product Description The IC693PRG300 is a portable hand-held programming device for the GE Fanuc Series 90‑30 PLC family. It provides field engineers and technicians with a direct interface to create, edit, debug, and monitor PLC logic using Statement List (STL) language. The device connects via a 15‑pin D‑type cable (IC693CBL303) that supplies power while signaling the PLC that an HHP is attached, eliminating the need for communication parameter configuration. This programmer supports multiple operational modes, enabling full on-site diagnostics, logic modification, and I/O parameter adjustments. Its compact design, tactile keypad, and LCD display make it ideal for portable programming and maintenance tasks. Key Features Supports Statement List (STL) programming language Compatible with GE Fanuc Series 90‑30 PLCs Operates in Program, Protection, Data, and Configuration modes Non-volatile internal memory with optional expansion via IC693ACC303 (for CPUs 311–341) Connects directly to the CPU’s serial port with hot-plug capability 42-key sealed tactile keypad and 2×16 character LCD display Powered entirely through the PLC serial cable, no batteries required Rugged design suitable for industrial field use Technical Specifications Functional & Communication Programming Language: STL Supported PLCs: Series 90‑30 Modes of Operation: Program, Protection, Data, Configuration Memory Type: Non-volatile, expandable via IC693ACC303 card Communication: 15‑pin D‑type serial connector, hot-plug capable Communication Parameter Setup: Not required User Interface Keypad: 42 tactile keys (6×7 matrix) Display: 2-line × 16-character LCD Mechanical & Physical Dimensions: 22.44 × 8.89 × 10.00 cm (alternate: 180 × 110 × 30 mm) Weight: 0.75 lbs Origin: USA Power & Electrical Power Source: Supplied through PLC serial cable Battery Life: Not applicable; powered directly by PLC Environmental Designed for industrial field applications Suitable for portable programming and on-site diagnostics Typical Applications Field programming and on-site PLC logic updates I/O module configuration Real-time monitoring and debugging of Series 90‑30 systems Access control via Protection Mode Reference table monitoring and adjustment FAQ Q: Do I need to configure communication settings to use the HHP?A: No, the IC693PRG300 automatically communicates with the PLC without parameter setup. Q: Can the memory be expanded?A: Yes, memory expansion is available via IC693ACC303 card for compatible CPU models. Q: What modes are available for field operation?A: Program, Protection, Data, and Configuration modes are supported. Q: Is the programmer portable for field use?A: Yes, its compact design and cable-powered operation make it ideal for portable field programming.
$200.00 $100.00
-
General Electric GE Fanuc IC693APU305 Series 90‑30 High-Speed I/O Processor Module
Product Description The IC693APU305 is a high-performance I/O processor module designed for GE Fanuc Series 90‑30 PLCs, providing independent, fast I/O processing for demanding industrial applications. With a dedicated processor onboard, this module offloads high-speed input/output operations from the main CPU, delivering deterministic timing for pulse counting, motion control, event capture, and synchronized processes. This module enables rapid response control without waiting for the CPU scan cycle, making it ideal for packaging, labeling, material handling, and high-frequency monitoring tasks. Key Features Dedicated I/O processor for independent input/output logic execution High-speed digital input and output processing with microsecond-level refresh 32-bit total counts register for pulse and event tracking Configurable outputs with fuse protection and positive logic signaling Six green LEDs for module, output, and configuration status Optically and galvanically isolated I/O for noise and surge immunity Compact design compatible with any Series 90‑30 baseplate slot Compatible with Logicmaster 90‑30, VersaPro, and HHP programming Technical Specifications Electrical & Input/Output Digital Inputs: 12 channels Input Voltage: 5 VDC TTL or 10–30 VDC industrial signals Input Type: Positive logic, high-speed pulse compatible Input Frequency: 50–60 Hz (AC-type signals) Digital Outputs: 8 channels Output Current: 4 outputs @ 1 A, 4 outputs @ 0.5 A (configurable) Output Type: Positive logic, fuse-protected Power Supply: 5 VDC via PLC backplane Performance & Processing Update Speed: 500 microseconds Total Counts Register: 32-bit Pulse Length & Interval Measurement: Millisecond resolution Data Registers: 4 pass-through registers CPU Communication: 32 discrete inputs (%I), 32 discrete outputs (%Q), 15 analog input words (%AI), 6 analog output words (%AQ) Mechanical & Environmental Dimensions: 64 × 127 × 102 mm (alternate: 10.25 × 8.2 × 8 cm) Weight: 0.8 lbs Operating Temperature: 0–60 °C (32–140 °F) Humidity: Up to 95% non-condensing Isolation: Optical and galvanic protection Indicators Six LED indicators for module status, output status, and configuration confirmation Typical Applications High-speed motion control Pulse counting and frequency measurement Event capture and process synchronization Packaging, labeling, and marking systems Bulk material handling and processing FAQ Q: Can the IC693APU305 handle independent logic without CPU intervention?A: Yes, it has an onboard processor that executes user-defined logic directly on the module. Q: What input voltage types are supported?A: Supports 5 V TTL and 10–30 V industrial signals, both positive logic. Q: Is the module protected against electrical noise?A: Yes, I/O channels are optically and galvanically isolated. Q: How is the module configured?A: Using Logicmaster 90‑30, VersaPro, or a Hand-Held Programmer; no DIP switches needed.
$200.00 $100.00
-
General Electric GE Fanuc IC698ACC701 RX3i/RX7i Auxiliary Smart Battery & Accessory Module
Product Description The IC698ACC701 is a versatile auxiliary module for GE Fanuc RX3i and RX7i PACSystems, combining backup power, communication support, and advanced accessory functionality. It safeguards CPU memory against power loss, enables robust RS‑232/485 and Ethernet connectivity, and provides terminal expansion for analog and digital I/O. This module is engineered for reliability in harsh industrial environments, including manufacturing, process automation, and energy systems. Depending on system integration, the IC698ACC701 may serve as a smart battery module, communication accessory, or advanced wiring accessory. All variants share a compact, durable design and compatibility with RX3i/RX7i CPUs. Key Features Auxiliary Smart Battery provides 3.6 V DC backup for CPU RAM Lithium-Thionyl Chloride chemistry ensures long service life (~5 years) and up to 200 days runtime Integrated 4‑pin JAE connector with adapter for seamless installation Communication module supports RS‑232/RS‑485 and Ethernet interfaces Rugged construction and wide temperature tolerance for industrial-grade applications Advanced accessory variant enables digital and analog signal consolidation, 500 VAC isolation, and single-slot rack mounting Technical Specifications Electrical & Battery Type: Auxiliary Smart Battery / Accessory Module Voltage: 3.6 V DC Capacity: 7 Ah Chemistry: Lithium / Thionyl Chloride (Li‑SOCl₂) Max Current: 15 A Battery Life: Up to 200 days Typical Service Life: ~5 years Lithium Content: 5.1 g Environmental Operating Temperature: 0°C to 60°C (battery); –25°C to +70°C (communication accessory) Storage Temperature: –40°C to +70°C Humidity: 5%–95% non‑condensing Casing: Flame-retardant ABS (battery) / Rugged metal (communication accessory) Mechanical Battery Module Dimensions: 14.5 × 6.35 × 3.8 cm Weight: 0.19 lbs Communication Accessory Module Dimensions: 178 × 102 × 254 mm, 1.27 kg Advanced Accessory Module (RX3i) Dimensions: 44 × 132 × 310 mm, 0.4 kg Connectivity Embedded 4‑pin female JAE connector Includes factory-supplied 4‑pin male to 2‑pin female adapter Supports integration with RX3i/RX7i CPUs and I/O chassis Applications CPU RAM backup for RX3i/RX7i systems PLC–HMI and PLC–I/O communication over RS‑232, RS‑485, and Ethernet Signal consolidation and terminal expansion for digital (24 VDC) and analog (0–10 V, 4–20 mA) inputs Industrial manufacturing, process control, and energy management systems FAQ Q: Can the IC698ACC701 replace standard RX3i battery modules?A: Yes, the auxiliary smart battery variant provides full CPU RAM backup. Q: Is the communication accessory compatible with Ethernet-based systems?A: Yes, it supports RS‑232/RS‑485 and Ethernet interfaces for diagnostics and firmware updates. Q: What environments can it operate in?A: Battery modules operate at 0–60 °C; communication and advanced accessory variants are rated for –25–70 °C. Q: Are adapters included for installation?A: Yes, all variants include the necessary JAE connector adapters.
$200.00 $100.00
-
General Electric GE Fanuc IC690ACC901 RS‑422/RS‑485 to RS‑232 Mini Converter Kit
Product Description The IC690ACC901 is a compact mini converter designed to connect GE Fanuc Series 90 PLCs to RS‑232 devices, including PCs, HMIs, barcode scanners, and serial printers. It converts RS‑422 (SNP) half-duplex signals from the PLC to RS‑232 full-duplex communication, enabling seamless programming, diagnostics, and data exchange. The kit includes a mini converter, a 2-meter serial extension cable, and a 9‑pin to 25‑pin adapter plug for legacy PCs. It plugs directly into the PLC’s 15‑pin SNP port, providing a 9‑pin RS‑232 interface with LED indicators for transmit and receive activity. Key Features Converts RS‑422/RS‑485 (SNP) signals from PLC to RS‑232 for PCs or serial devices Direct plug-in to 15‑pin PLC SNP port Supports multidrop communication with up to 8 devices TX/RX LEDs for communication status Compact design, lightweight, and easy to install Compatible with GE programming software: Logicmaster 90, VersaPro, and Proficy Machine Edition Includes 2-meter serial extension cable and DB9-to-DB25 adapter Technical Specifications Electrical & Interface RS‑232 Port Pinout Pin 2: Send Data (Output) Pin 3: Receive Data (Input) Pin 5: Ground Pin 7: Clear to Send (Input) Pin 8: Request to Send (Output) RS‑422 (SNP) Port Pinout SHLD: Shield 5: +5 VDC Input 6: CTS(A) Input 7: GND 8: RTS(B) Output 9: Receive Termination Output 10: Send Data(A) Output 11: Send Data(B) Output 12: Receive Data(A) Input 13: Receive Data(B) Input 14: CTS(B) Input 15: RTS(A) Output Physical Specifications Dimensions: 3.5 × 13 × 13.5 cm Weight: 0.3 kg Country of Origin: USA Applications GE Fanuc Series 90‑30, 90‑70, 90‑20 PLC programming Connecting PLCs to HMIs, barcode scanners, serial printers SCADA and remote I/O system communication PC-based monitoring and configuration FAQ Q: Can this converter support multiple PLCs on a single line?A: Yes, it supports multidrop communication for up to 8 devices. Q: Does it need external power?A: Most versions draw power directly from the RS‑232 serial interface. Q: Which GE software is compatible?A: Logicmaster 90, VersaPro, and Proficy Machine Edition. Q: Are all necessary cables included?A: Yes, the kit includes a 2-meter extension cable and DB9-to-DB25 adapter.
$200.00 $100.00
-
General Electric GE Fanuc IC693CPU352 Series 90‑30 CPU Module for High-Speed PLC
Product Description The IC693CPU352 is a single-slot CPU module for the GE Fanuc Series 90‑30 PLC platform, designed for medium-to-large automation systems requiring high-speed logic, floating-point calculations, and extensive I/O support. Utilizing an Intel 80386EX processor at 25 MHz, this module offers fast scan rates, flexible memory configuration, and multiple serial communication options. Its compact single-slot design maximizes available rack space for I/O or expansion modules. Key Features Single-slot CPU module, supports up to 8 baseplates (1 CPU + 7 expansion/remote) 80386EX processor at 25 MHz for high-speed execution Hardware floating-point math co-processor for intensive calculations Three built-in serial ports supporting SNP/SNP‑X, RTU master/slave, and general serial I/O Configurable memory up to 240 KB user program memory (firmware ≥9.0) Extensive diagnostics with battery-backed clock and Flash memory High-capacity I/O: 2,048 discrete inputs/outputs, up to 32,640 analog points Technical Specifications Processor & Performance Processor: Intel 80386EX Clock Speed: 25 MHz Typical Scan Rate: 0.22 ms per 1K Boolean logic Floating-Point Math: Hardware-based Memory User Program Memory: Up to 240 KB Register Memory (%R): 128–32,640 words Internal Coils (%M): 4,096 bits Temporary Coils (%T): 256 bits Global Memory (%G): 1,280 bits System Status (%S): 128 bits I/O Capacity Discrete Inputs (%I): 2,048 points Discrete Outputs (%Q): 2,048 points Analog Inputs (%AI): Up to 32,640 words Analog Outputs (%AQ): Up to 32,640 words Timers/Counters: >2,000 Communication Ports Power Supply Port: SNP/SNP‑X slave Port 1 (RS‑232): SNP/SNP‑X master/slave, RTU slave, Serial I/O Port 2 (RS‑485): Same as Port 1; supports multidrop networks Optional modules for Ethernet, Profibus, FIP, GBC, and GCM+ Power & Environmental Backplane Current: 890 mA @ +5 VDC Operating Temperature: 0–60 °C (32–140 °F) Weight: 0.71 lb Typical Applications Medium to large-scale industrial automation systems High-speed logic operations with floating-point processing requirements Multi-rack distributed I/O systems Environments requiring robust serial and optional Ethernet communication FAQ Q: How many baseplates can IC693CPU352 support?A: It supports up to 8 baseplates—1 CPU plus 7 expansion or remote I/O baseplates. Q: Does it support floating-point calculations?A: Yes, it has a hardware-based floating-point math co-processor for intensive computations. Q: What types of serial communications are available?A: Three built-in ports support SNP/SNP-X, RTU master/slave, and general serial communications. Q: Can memory be expanded?A: Yes, user memory is configurable up to 240 KB, with flexible register and coil assignments.
$200.00 $100.00
You have seen 24 out of 96 products