PLC systems and modules deliver flexible automation for industries worldwide. Our inventory includes controllers, input/output modules, and communication units from Allen-Bradley, Siemens, GE, and other leading brands.
PLC Systems & Modules
-
Bently Nevada Bently Nevada 3500/22M 146031-01 Ethernet I/O Communication Module
Product Description The Bently Nevada 3500/22M 146031-01 Ethernet I/O Module is the rear-mounted communication interface used in conjunction with the 3500/22M Transient Data Interface (TDI). Installed behind Slot 1 of the rack, it forms the physical network bridge that enables external communication between the 3500 system and plant-level monitoring platforms. This module is responsible for all Ethernet-based data exchange functions, including System 1 connectivity, waveform transfer, and rack-level configuration management. It also provides the hardware interface for system health signaling through the OK relay output. The unit operates outside the protection loop, ensuring that machinery protection remains active even if the communication interface is removed or fails. Communication Architecture Rear I/O Ethernet interface module for 3500/22M TDI systems Provides copper RJ-45 network connection Supports 10/100 Mbps auto-negotiated communication Auto MDI/MDIX eliminates crossover cable requirements Fully compliant with IEEE 802.3 / 802.3u standards Supported data services: System 1 condition monitoring communication High-speed vibration waveform transmission Transient event data transfer Rack configuration upload and download Modbus TCP communication over Ethernet Electrical Characteristics Powered through 3500 rack backplane (no external supply required) Integrated with TDI module power consumption profile (approx. 10.5 W system load) OK relay output: 5 A @ 24 VDC or 120 VAC Maximum switching load: 120 W / 600 VA Gold-plated low-current contacts (down to 1 mA @ 1 VDC) Built-in arc suppression design Normally energized operating state Functional Behavior Establishes Ethernet communication path for the TDI processor Enables real-time vibration and transient data streaming Provides rack health status output to DCS/PLC systems via relay Supports full integration with M-series monitor modules Maintains communication continuity during hot-swap operations Mechanical Configuration Installation location: Rear of rack behind Slot 1 (TDI position) Form factor: Full-height rear I/O module Dimensions: 241 × 24 × 100 mm Weight: 0.20 kg Designed for direct mating with 3500 rack backplane connectors Environmental Performance Operating temperature range: -30°C to +65°C Storage temperature range: -40°C to +85°C Relative humidity: 0–95% non-condensing Designed for continuous duty in harsh industrial environments Suitable for refinery, offshore, turbine, and compressor monitoring systems System Integration Role Provides Ethernet hardware layer for 3500/22M TDI systems Enables System 1 diagnostics and visualization connectivity Supports Modbus TCP for third-party control system integration Compatible with all M-series modules including 3500/40M, 3500/42M, and 3500/45M Ensures uninterrupted communication during module maintenance or replacement FAQ Q1: Is this module part of the protection system logic?No. It operates strictly as a communication interface and does not affect protection functions. Q2: Can the system run without this I/O module?Yes, but external Ethernet communication and System 1 connectivity will be unavailable. Q3: Is the module hot-swappable?Yes. It is designed for replacement without powering down the rack.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/22 146031-01 Ethernet I/O Communication Module
Product Description The 3500/22 (146031-01) is a rear-installed Ethernet communication interface designed for the Bently Nevada 3500/22M Transient Data Interface system. Positioned behind Slot 1 of the rack, it serves as the primary network gateway between the monitoring rack and external condition monitoring platforms such as System 1. This module replaces earlier communication components used in legacy 3500 architectures, consolidating network connectivity and data exchange functions into a dedicated Ethernet interface unit. It is strictly a communication component and does not participate in machinery protection logic or voting functions. A failure of this module does not interrupt the protective operation of the 3500 rack. Core Functions Provides Ethernet connectivity for 3500 rack systems Enables communication with System 1 software platform Transfers steady-state and transient vibration data Supports rack configuration upload and download Interfaces with M-series monitoring modules Acts as communication bridge for diagnostic data Maintains isolation from protection logic path Communication Specifications Parameter Specification Ethernet Type 10Base-T / 100Base-TX Connector Type RJ-45 Copper Interface Auto Negotiation Supported Auto MDIX Supported Standards IEEE 802.3 / 802.3u Data Rate 10 / 100 Mbps Electrical Characteristics Parameter Specification Power Source Supplied via 3500 rack backplane Associated Module 3500/22M TDI Power Consumption ~10.5 W (system dependent) Function Ethernet and rack communication interface Relay Output OK relay via TDI system OK Relay Specifications Parameter Specification Contact Rating 5 A @ 24 VDC / 120 VAC Minimum Load 1 mA @ 1 VDC Contact Type Gold-plated contacts Protection Arc suppression integrated Operation Mode Normally energized system logic Front Panel Indicators (via TDI System) Indicator Function OK LED System operational status TX/RX LED Network communication activity TM LED Trip Multiply status CONFIG OK LED Valid configuration confirmation Control Function Rack Reset Button Clears latched alarms Address Switch Rack address configuration (1–127) Key Switch RUN / PROGRAM mode selection Mechanical Specifications Parameter Specification Model 3500/22 (146031-01) Mounting Location Rear of 3500 rack, Slot 1 rear position Module Type Ethernet I/O interface module Dimensions 3 × 12 × 25 cm Weight 0.45 kg Environmental Ratings Operating Temperature: -30°C to +65°C Storage Temperature: -40°C to +85°C Humidity: Up to 95% non-condensing Designed for continuous industrial-duty environments System Role Within the 3500 architecture, the 3500/22 (146031-01) functions as the communication backbone for the TDI system. It: Enables real-time condition monitoring data transfer Supports vibration waveform and transient event capture Provides Ethernet access for engineering and diagnostic tools Ensures separation from safety and protection logic FAQ Is this module part of the protection system logic?No. It is strictly a communication interface and does not influence protection or trip decisions. What software does it integrate with?It is designed for full compatibility with Bently Nevada System 1 condition monitoring software. Can the system operate without this module?Yes, but remote communication, waveform transfer, and System 1 integration will not be available. What is its primary function in the rack?It provides Ethernet-based communication between the 3500 rack and external monitoring systems.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/22 125768-01 Rack Interface I/O Module
Product Description The 3500/22 (125768-01) is a rear-mounted interface module designed for the Bently Nevada 3500 machinery protection platform. It functions as the physical connection layer for the 3500/22 Transient Data Interface (TDI), enabling communication, configuration access, and high-speed data exchange between the rack and external monitoring systems. Installed at the rear of the rack directly behind the TDI front module, this unit forms part of the system’s communication infrastructure. It is responsible for providing network connectivity and data routing while leaving the protection and voting logic of the system unaffected. The module is not involved in protection decision-making; its role is strictly communication and data handling within the 3500 architecture. Core Functions Provides physical Ethernet interface for 3500/22 TDI Enables high-speed data transmission between rack and external systems Supports configuration upload and download functions Transfers steady-state and transient waveform data Integrates with System 1 condition monitoring software Maintains separation from protection and voting logic Supports remote diagnostic access and rack communication Communication Interfaces Interface Specification Ethernet Port 1 10/100Base-TX (Auto-sensing) Ethernet Port 2 100Base-FX Fiber (configuration dependent) USB Port USB-B (local configuration access) These interfaces allow: High-speed vibration waveform transfer System 1 connectivity Remote diagnostics and monitoring Rack configuration management Electrical Characteristics Parameter Specification Power Source Supplied via 3500 rack backplane Function Ethernet and configuration I/O interface Relay Support Provided via associated TDI module Relay Rating 5 A @ 24 VDC / 120 VAC Contact Type Gold-plated, low-current compatible Minimum Switching Load 1 mA @ 1 VDC Arc Protection Integrated suppression circuit Front Panel Indicators & Controls (via TDI System) Indicator Function OK LED Normal system operation TX/RX LED Communication activity status TM LED Trip Multiply active state CONFIG OK LED Valid configuration status Control Function Rack Reset Button Clears latched alarms and faults Address Switch Configures rack address (1–127) Mode Key Switch Selects RUN or PROGRAM mode Mechanical Details Parameter Specification Model 3500/22 (125768-01) Mounting Location Rear of 3500 rack, behind TDI module Module Type Rear interface I/O assembly Dimensions 2.5 × 11.2 × 24.2 cm Weight 0.45 kg Environmental Design Engineered for continuous operation in harsh industrial environments Suitable for high-vibration and high-noise electrical areas Commonly deployed in process plants, turbine halls, and compressor stations Compatible with long-term monitoring installations System Role Within the 3500 architecture, the 3500/22 (125768-01) performs as a communication backbone component. It: Bridges rack-level data with external monitoring systems Supports real-time waveform and transient event transmission Enables integration with predictive maintenance platforms Does not influence protection logic or trip decision pathways FAQ Is this module part of the protection system logic?No. It handles communication and data transfer only and does not participate in protection or voting functions. What software does it support?It is designed for integration with Bently Nevada System 1 condition monitoring software. Can it operate without the TDI front module?No. It functions as the rear interface component and must be paired with the 3500/22 TDI module. What type of data can it transmit?It supports steady-state vibration data, transient waveform data, and system configuration information.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/15 125840-01 AC Power Input Module
Product Description The 3500/15 125840-01 High Voltage AC Power Input Module is engineered for use with the Bently Nevada 3500 Machinery Protection platform. Installed behind the associated 3500/15 power supply module, this Power Input Module (PIM) accepts high-voltage AC mains input and delivers conditioned power to the rack power supply system. Designed for continuous-duty industrial applications, the Bently Nevada 125840-01 supports reliable operation of monitoring and protection modules installed within 3500 rack assemblies. The module operates with nominal 220 Vac systems and accommodates a wide AC input range, making it suitable for power generation plants, petrochemical facilities, turbine monitoring systems, and heavy rotating equipment installations. The module supports both standalone and redundant power supply architectures. In dual-supply configurations, the PIM enables automatic failover functionality and uninterrupted rack operation during maintenance or module replacement procedures. Hot-swappable capability allows service technicians to replace a module without shutting down the entire monitoring system when redundant power is available. Its compact half-height design simplifies rack integration while maintaining high conversion efficiency and stable power conditioning performance under varying industrial load conditions. Technical Specifications Parameter Specification Model Number 3500/15 Part Number 125840-01 Manufacturer Bently Nevada Product Type High Voltage AC Power Input Module Product Series 3500 Machinery Protection System Compatible Module 3500/15 Power Supply Installation Type Backplane Mounted Module Format Half-Height Redundancy Support Yes Hot Swap Capability Supported Rack Compatibility 3500 Rack Systems Electrical Specifications Parameter Value Nominal Input Voltage 220 Vac Input Voltage Range 175–264 Vac RMS Peak Voltage Range 247–373 Vac Peak Frequency Range 47–63 Hz Maximum Output Current 2.3 A RMS Conversion Efficiency Up to 90% Protection Features Overvoltage fuse protection Undervoltage tolerance without module damage Stable conditioned power delivery Automatic redundant power switchover support Industrial-grade electrical isolation and protection design Environmental Specifications Parameter Specification Operating Temperature -30°C to +65°C Storage Temperature -40°C to +85°C Relative Humidity 0–95% Non-Condensing Mechanical Specifications Parameter Value Dimensions 120.7 × 25.4 × 114.3 mm Weight 0.34 kg Mounting Method Rack Backplane Installation Functional Characteristics The 125840-01 module performs incoming AC conditioning for the associated 3500/15 power supply and distributes stable operating power throughout the rack system. The design supports: High-voltage AC input applications Dual power supply redundancy Continuous monitoring system uptime Simplified maintenance through hot-swappable installation Compact integration into standard 3500 racks Typical Applications This module is commonly used in: Steam turbine monitoring systems Gas compressor protection systems Generator vibration monitoring Industrial motor protection applications Oil and gas production facilities Refinery process monitoring systems Critical rotating equipment installations FAQ What is the purpose of the 125840-01 module? The module conditions high-voltage AC input power for the compatible 3500/15 rack power supply within the 3500 Machinery Protection System. Can the module be replaced during operation? Yes. When a redundant power supply configuration is installed, the module supports hot-swappable replacement without interrupting rack operation. Is the module compatible with all 3500 racks? The module is designed for compatible Bently Nevada 3500 rack systems using the 3500/15 power supply assembly.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/15 106M1081-01 Universal AC Power Input Module
Product Description The 106M1081-01 Universal AC Power Input Module is designed for integration with the Bently Nevada 3500/15 power supply assembly within the 3500 Machinery Protection System. This module conditions incoming AC mains power and delivers stabilized input power to the associated 3500/15 power supply module for rack-wide distribution. Engineered for continuous industrial operation, the Bently Nevada 106M1081-01 supports a broad universal AC voltage range without requiring manual jumper configuration or input selection adjustments. The module installs directly behind the corresponding 3500/15 power supply in the left section of the rack chassis. For high-availability applications, the module supports redundant power configurations. When dual Power Input Modules and dual power supplies are installed, the system automatically balances the electrical load while enabling uninterrupted failover during maintenance or power supply replacement procedures. The module incorporates surge suppression, isolation protection, and low leakage current characteristics to support reliable operation in critical machinery monitoring environments including turbine control systems, compressor trains, process plants, and power generation facilities. Technical Specifications Parameter Specification Model Number 106M1081-01 Manufacturer Bently Nevada Product Type Universal AC Power Input Module Compatible Power Supply 3500/15 Product Series 3500 Machinery Protection System Installation Position Rear of 3500/15 Power Supply Rack Compatibility 3500 Rack Systems Redundancy Support Yes Hot Swap Capability Supported Protection Rating IP20 Cooling Method Passive Cooling Electrical Input Specifications Parameter Value Input Voltage Range 85–264 Vac RMS Frequency Range 47–63 Hz Peak Voltage Tolerance 120–373 Vac Peak Inrush Current Less than 25 A Peak Inrush Duration Less than 5 ms Surge Protection MOV and Gas Tube Protection Filtering Method Differential-Mode Choke Isolation Ratings Isolation Type Rating Input to Earth 1.5 kVac Input to Output 500 Vdc Power Handling Performance The 106M1081-01 module supports the associated 3500/15 power supply with rack current capability up to 2.8 A RMS at 240 Vac input conditions. Integrated protection functions include: Undervoltage protection without module damage Fuse-based overvoltage isolation Automatic load sharing in redundant systems Seamless failover operation during maintenance Environmental Specifications Parameter Specification Operating Temperature -30°C to +65°C Storage Temperature -40°C to +85°C Relative Humidity 95% Non-Condensing Mechanical Specifications Parameter Value Dimensions 120.7 × 25.4 × 114.3 mm Weight 0.34 kg Connector Type IEC C14 Inlet Rack Connection Crimp Fork Terminal Interface Functional Features Universal AC input without voltage selection jumpers Hot-swappable during redundant operation Compatible with dual power supply redundancy architectures Front-panel status indication LEDs Integrated monitoring support through 3500/20 Rack Interface Module High surge immunity compliant with IEC 61000-4-5 Low leakage current for sensitive protection systems Typical Applications The Bently Nevada 106M1081-01 module is commonly deployed in: Steam turbine monitoring systems Gas compressor protection platforms Boiler feedwater pump monitoring Heavy-duty industrial motor protection Offshore production facilities Rotating machinery condition monitoring Nuclear plant auxiliary pump systems FAQ What is the function of the 106M1081-01 module? The module conditions and distributes universal AC input power to the compatible 3500/15 power supply within the 3500 rack system. Can the module be replaced while the rack is operating? Yes. In redundant configurations, the module supports hot-swapping without interrupting rack operation. Does the module support automatic failover? Yes. Dual-module installations provide automatic load sharing and seamless backup operation if one supply path becomes unavailable.
$200.00 $100.00
-
EMERSON Emerson Ovation 1C31224G01 8-Channel Analog Input Module
Product Description Overview The Emerson Ovation 1C31224G01 is an 8-channel analog input module engineered for reliable process control. It captures 4–20mA current signals and converts them into high-resolution digital data, ensuring precise monitoring and maintaining the integrity of your control system. Factory-certified by Emerson, this module is designed to reduce downtime and support continuous, stable operation in demanding industrial environments. Technical Specifications Model: 1C31224G01 Channels: 8 isolated analog input channels Input Type: 4–20mA current signals Resolution: 14-bit Certification: Factory-certified by Emerson Purpose: Maintains control system integrity and minimizes operational downtime Communication Interface: Compatible with Ovation control networks Operating Temperature: -40°C to +70°C (recommended) Storage Temperature: -40°C to +85°C Mounting: DIN rail mountable or panel integration (depending on cabinet design) Weight: Approx. 0.5 kg Physical Dimensions: Width 178mm × Height 90mm × Depth 100mm Applications Continuous process monitoring and control Distributed Control Systems (DCS) analog input Industrial signal acquisition for 4–20mA sensors Redundant and high-availability control systems FAQ Q: How many channels does the module support?A: The 1C31224G01 supports 8 individually isolated analog input channels for reliable signal acquisition. Q: What is the input signal type and resolution?A: It supports 4–20mA current signals with 14-bit high-resolution conversion for precise data capture. Q: Is this module factory-certified?A: Yes, it is factory-certified by Emerson to ensure reliability and consistent performance. Q: How does this module help reduce downtime?A: Its robust design, isolated channels, and high signal accuracy minimize system errors and operational interruptions. Q: What installation options are available?A: The module can be mounted on standard DIN rails or integrated into control panels, depending on the system layout.
$200.00 $100.00
-
EMERSON Ovation 5X00070G01 Module | 4-20mA Analog Input Converter
Product Description Overview The Ovation 5X00070G01 module is a high-precision analog signal acquisition device designed for industrial automation systems. It converts 4–20mA current signals into digital values for monitoring, control, and data processing. This module is an integral component of the Ovation High-Speed Analog Input subsystem, suitable for applications requiring high signal accuracy and system reliability. Technical Specifications Input Type: Current signal Input Range: 4–20mA Resolution: 14-bit Channels: 8 individually isolated input channels Sampling Rate: 50 or 60 samples per second Channel Isolation: Each channel fully isolated Surge Protection: Integrated to prevent damage from transient voltage Power Supply: Requires external power; compatible with field-powered devices Operating Temperature: -40°C to +70°C Storage Temperature: -40°C to +85°C Relative Humidity: 0% to 95%, non-condensing Dimensions: Width 178mm × Height 90mm × Depth 100mm Weight: 0.5 kg Mounting: DIN rail mountable Communication Interface: Ovation Serial I/O Bus Applications High-precision process control systems Industrial automation data acquisition Distributed Control Systems (DCS) analog input Real-time monitoring of field devices FAQ Q: Does the module support multiple sampling rates?A: Yes, the 5X00070G01 supports 50 or 60 samples per second to meet different control requirements. Q: Are the input channels isolated?A: Yes, each input channel is independently isolated, ensuring system reliability and minimizing interference. Q: What is the mounting method?A: The module is DIN rail mountable, allowing easy integration into standard control cabinets. Q: What is the operating temperature range?A: The module operates from -40°C to +70°C and can be stored from -40°C to +85°C. Q: Is surge protection included?A: Yes, surge protection is built into the input circuitry to ensure long-term stable operation.
$200.00 $100.00
-
EMERSON Ovation 1C31181G01 Remote I/O Module Westinghouse Control System
Product Description Overview The 1C31181G01 is a high-performance Remote I/O Module developed by Ovation/Westinghouse. Designed as a Remote I/O Master Unit, it enables robust communication and centralized control for distributed automation systems. Its compact design ensures easy integration into various industrial setups while maintaining reliable performance under demanding conditions. Key Features Remote I/O Master Capability: Enables efficient control of distributed I/O devices over extended distances. Compact Footprint: Small form factor allows seamless integration into tight control cabinets. High-Speed Communication: Supports stable and fast data exchange for real-time monitoring and control. Technical Specifications Electrical Specifications Input Voltage: 24V DC Current Rating: 2A (steady-state operation) Environmental Specifications Operating Temperature: -20°C to +70°C Storage Temperature: -40°C to +85°C Relative Humidity: 5% to 95%, non-condensing Communication & Connectivity Protocol: RS-485 Maximum Data Rate: 1 Mbps Connector Type: Standard industrial terminal block Mechanical Dimensions Dimension Size Length 2.5 cm (1.0 inch) Width 9.5 cm (3.8 inches) Height 12.1 cm (4.8 inches) Weight 0.1 kg (0.22 lbs) Applications Distributed process control systems Remote monitoring and supervisory control Integration with Ovation control platforms in power generation, water treatment, and industrial automation systems FAQ Q: Can the 1C31181G01 operate in outdoor environments?A: It is rated for -20°C to +70°C and 5–95% non-condensing humidity, suitable for most industrial enclosures but should be protected from direct exposure to rain or snow. Q: Can this module communicate with non-Ovation systems?A: Yes, it supports standard RS-485 protocol, allowing integration with compatible devices, though full Ovation functionality may require proprietary interfaces. Q: How does it compare to similar Ovation modules?A: Compared to older Ovation Remote I/O models, 1C31181G01 offers higher data transfer rates, more compact size, and enhanced environmental tolerance.
$200.00 $100.00
-
EMERSON VDCLogic 1C31179G01 Input/Output Remote Module | CO, CQ Series
Product Description OverviewThe 1C31179G01 Input/Output Remote Module from VDCLogic delivers dependable signal acquisition and output capabilities for advanced control systems. Engineered for both digital and analog processing, this compact module supports a wide range of industrial applications, ensuring high reliability and low power operation. Technical Specifications Specification Details Part Number 1C31179G01 Product Type Input/Output Remote Module Series CO, CQ Manufacturer VDCLogic Weight 0.42 kg (0.93 lbs) Dimensions 12.7 cm x 12.7 cm x 3.2 cm Electrical Input Digital 0–5V, Analog 0–10V / 4–20 mA Electrical Output Digital 0–5V, Analog 0–10V / 4–20 mA Power Supply 24V DC Power Consumption Minimal, optimized for low energy usage Operating Temperature -20°C to +70°C Humidity 5% to 95% non-condensing Country of Manufacture USA Release Year 2021 ApplicationsThe 1C31179G01 module is suitable for industrial control systems requiring precise I/O management. Typical applications include process monitoring, distributed control systems, data acquisition modules, and small to medium-scale automation networks. FAQ Q: Can this module handle both analog and digital signals simultaneously?A: Yes, it supports mixed-signal configurations with digital 0–5V and analog 0–10V / 4–20 mA inputs and outputs. Q: What environments is this module suited for?A: It operates reliably in temperatures from -20°C to +70°C and under 5%–95% non-condensing humidity. Q: How does this model differ from other CO/CQ series modules?A: Compared to other CO/CQ models, the 1C31179G01 offers a compact form factor and optimized low-power consumption while maintaining full analog/digital compatibility. Similar Models Comparison 1C31178G01 – Slightly smaller dimensions, supports fewer I/O channels. 1C31180G02 – Higher channel density with enhanced signal filtering.
$200.00 $100.00
-
EMERSON Emerson Ovation 1C31205G01 Remote Node Controller Base PLC Module
Product Description OverviewThe 1C31205G01 Remote Node Controller Base from Emerson is a critical module within the Ovation Distributed Control System (DCS), designed to manage and interface with remote I/O nodes across a control network. This base unit streamlines system expansion while offering versatile connectivity for multiple I/O branches. Its modular design ensures ease of installation, robust operation, and seamless integration with other Ovation components. Technical Specifications Specification Details Part Number 1C31205G01 Product Type Remote Node Controller Base Category PLCs / Machine Control Subcategory PLC Module / Rack Weight 1.35 lbs (0.61 kg) Manufacturer Emerson Maximum Remote Node Modules 2 Node Addressing Rotary switch for simple node selection I/O Branch Connections Direct connection to 2 I/O branches; additional connection via D-connector supports up to 6 extra branches Compatibility Interfaces with Emerson Remote Node Transition Panel Status Discontinued by manufacturer ApplicationsThe 1C31205G01 base is ideal for distributed control environments requiring precise, reliable node management. It supports small to mid-sized DCS networks, including power generation, process automation, and industrial monitoring systems. FAQ Q: Can this module be used with more than two remote nodes?A: The base supports up to 2 remote node modules directly. Additional nodes require compatible transition panels and expansion branches. Q: Is this controller compatible with all Ovation I/O modules?A: It interfaces with standard Ovation remote node modules. Compatibility should be verified with specific I/O module types. Q: Why is this product discontinued?A: Emerson has phased out the 1C31205G01 in favor of updated Remote Node Controller series. Legacy support may still be available through Emerson service channels. Similar Models Comparison 1C31206G01 – Supports additional I/O branches and enhanced communication protocols. 1C31207G02 – Includes integrated diagnostics and monitoring features for larger node networks.
$200.00 $100.00
-
EMERSON Ovation The1C31166G01 Serial Link Controller Input Module
Product Description OverviewThe The1C31166G01 (Order Number: N/A) from Ovation is a high-performance Serial Link Controller Input Module engineered for seamless integration with Ovation control systems. It provides robust, precise serial communication to support data acquisition, monitoring, and system control tasks. Compact and durable, this module ensures reliable performance in a variety of industrial environments. Key Features High System Compatibility: Fully compatible with Ovation automation and control systems. Reliable Data Transmission: Advanced error-checking protocols ensure accuracy and integrity. Flexible Serial Configuration: Supports multiple serial link setups for diverse applications. Space-Efficient Design: Compact form factor allows easy mounting in control panels. Technical Specifications Parameter Specification Serial Link Interface Optimized for secure, high-speed communication Input Channels Multiple channels for varied input signals Signal Processing Advanced filtering and processing for high precision Operating Voltage 24 VDC Maximum Current per Channel 2 A Temperature Range 0°C to 60°C Humidity Range 5% to 95% RH, non-condensing Protection Rating IP20 Dimensions (L × W × H) 10 cm × 5 cm × 15 cm (4.0 in × 2.0 in × 6.0 in) Weight 0.32 kg (0.70 lbs) ApplicationsIdeal for use in data acquisition, process control, and automation systems within building management, energy, and industrial process monitoring environments. The module’s reliability and compact design make it suitable for installation in confined or high-density control panels. FAQQ: Can this module operate in high-humidity environments?A: Yes, it supports up to 95% relative humidity, non-condensing. Q: How many input channels does it support?A: It supports multiple input channels, allowing simultaneous monitoring of diverse signals. Q: Is the module compatible with other control systems?A: It is specifically optimized for Ovation systems; integration with other platforms may require custom configuration. Similar Models Comparison The1C31167G01: Similar serial controller with higher current capacity (3A per channel). The1C31168G01: Offers extended operating temperature range (-20°C to 70°C) for harsh environments.
$200.00 $100.00
-
EMERSON Ovation 5X00119G01 Personality Module | Signal Input Module 5X00121G01
Product Description OverviewThe 5X00119G01 is a versatile signal input module designed for use with the Ovation Personality system. It supports full-range input conversions and interfaces exclusively with the 5X00121G01 Personality module, excluding CE Mark certified systems. This module delivers reliable data acquisition for critical control and monitoring applications. Key Features and Technical Specifications Channels and Sampling Number of Input Channels: 8 Sampling Frequency: 50 Hz Mode: 16.67 samples/sec 50 Hz 3-Wire Mode: Lead resistance measured every 6.45 sec (effective sampling rate drops to 3/sec) 60 Hz Mode: 20 samples/sec 60 Hz 3-Wire Mode: Lead resistance measured every 6.45 sec (rate drops to 2/sec) Self-Calibration: Occurs on-demand; sampling temporarily reduces to 1/sec per cycle RTD Input Ranges Compatible with multiple RTD ranges (see Table 19A-3 for detailed ranges) Resolution: 12-bit Accuracy (@25°C): 0.10% typical; additional resistance-dependent variations apply Temperature Coefficient: 10 ppm/°C Electrical Characteristics Input Impedance: 100 MΩ (normal), 50 kΩ (power-down mode) Common Mode Rejection: 120 dB at DC and nominal power frequency Normal Mode Rejection: 100 dB at DC and nominal power frequency Isolation and Safety Channel-to-Channel Isolation: 200 V AC/DC Channel-to-Logic Isolation: 1000 V AC/DC Power and Environmental Module Power Consumption: 3.6 W typical, 4.2 W maximum Operating Temperature: 0 to 60°C (32 to 140°F) Storage Temperature: -40 to 85°C (-40 to 185°F) Humidity: 0–95% non-condensing Self-Calibration Executed on-demand via the Ovation Controller Ensures ongoing measurement accuracy ApplicationsIdeal for monitoring and controlling industrial processes requiring precise RTD measurements, such as: Power plants Chemical processing HVAC systems Critical environmental monitoring FAQQ: Can this module be used with CE Mark certified systems?A: No, it is not applicable for CE-certified Ovation systems. Q: What happens during 3-wire mode sampling?A: Lead resistance measurements are taken less frequently, which temporarily reduces the effective sampling rate. Q: Is self-calibration automatic?A: No, self-calibration is performed only on-demand via the Ovation Controller interface. Comparison with Similar Modules Unlike other Ovation input modules, 5X00119G01 provides 12-bit resolution with high common and normal mode rejection for highly accurate RTD readings. Compatible only with the 5X00121G01 Personality module, ensuring system integrity. Technical Specifications Table Parameter Specification Channels 8 Sampling Rate 50 Hz: 16.67/sec, 60 Hz: 20/sec (drops in 3-wire mode) RTD Resolution 12-bit Accuracy (@25°C) 0.10% typical Temperature Coefficient 10 ppm/°C Input Impedance 100 MΩ (50 kΩ in power-down) Isolation Channel-to-Channel: 200 V AC/DC, Channel-to-Logic: 1000 V AC/DC Power Consumption 3.6 W typical, 4.2 W max Operating Temp 0–60°C (32–140°F) Storage Temp -40–85°C (-40–185°F) Humidity 0–95% non-condensing Common Mode Rejection 120 dB ±1/2% Normal Mode Rejection 100 dB ±1/2%
$200.00 $100.00
-
EMERSON Emerson Ovation 1B30023H01 I/O Bus Terminator Module
Product Description Overview The Emerson Ovation 1B30023H01 is a compact I/O bus terminator module designed to maintain signal integrity in industrial control systems. By providing accurate termination impedance and a stable reference voltage, it ensures reliable operation across local I/O networks while protecting connected devices from electrical transients. Its rugged design and LED indicators simplify installation and monitoring in demanding industrial environments. Technical Specifications Electrical Characteristics Termination Impedance: 120 Ω Reference Voltage: 5.0 VDC Power Consumption: 100 mA Physical Dimensions & Weight Dimensions: 3.2 cm × 12.7 cm × 12.7 cm (100 mm × 50 mm × 25 mm) Weight: 0.42 kg (0.44 lbs) Compliance & Certification CE, UL, CSA, ATEX, IECEx Key Features Prevents Signal Reflections: Maintains signal integrity by properly terminating the I/O bus Stable Reference Voltage: Delivers consistent reference voltage for reliable bus operation Energy Absorption: Dissipates excess energy to protect connected modules LED Indicators: Provides visual status of power and bus operation for diagnostics Compact and Rugged Design: Enables easy installation and dependable operation in harsh conditions Application Scenarios Suitable for industrial automation, process control, and power generation systems Ensures stable communication in local I/O branches without additional terminators Ideal for control cabinets and field-mounted I/O bases where space is limited FAQ Q: Can this module be used on branches with active I/O modules?A: Yes, it is designed to terminate any I/O bus properly while maintaining voltage stability. Q: Does it provide visual status monitoring?A: Yes, integrated LED indicators show power and bus status for quick diagnostics. Q: What environments is this module suited for?A: Its compact and rugged design makes it suitable for harsh industrial conditions, including process and power generation plants. Similar Model Comparison Model Features Application 1B30023H01 Compact I/O bus terminator, 120 Ω, 5V reference, LED indicators Local I/O branches in industrial control 1B30023H02 Terminator for branches without AUM, dual-side installation Local I/O branches without AUM 1B30024H01 I/O bus terminator with high-temperature rating High-temperature industrial environments
$200.00 $100.00
-
EMERSON Emerson Ovation 1B30023H02 I/O Branch Terminator Module
Product Description Overview The Emerson Ovation 1B30023H02 I/O Branch Terminator is designed to provide accurate termination for local I/O branches without an Attachment Unit Module (AUM). It ensures stable communication, prevents signal reflections, and guarantees reliable data transfer across the Ovation control system. This module supports flexible installation on either side of standard I/O bases. Technical Specifications Compatibility Suitable for I/O branches that do not use an Attachment Unit Module Can be installed on both A-side and B-side of standard I/O bases Electrical Requirements Operating voltage: +24 VDC Supports redundant power configurations for enhanced reliability Communication Performance Effectively terminates the local I/O communication bus Prevents signal reflection and maintains data integrity Ensures consistent performance across the Ovation I/O network Physical & Installation Compact design compatible with standard Ovation I/O bases Can be mounted on either side of the base for minimal system downtime Application Scenarios Ideal for industrial plants using Emerson Ovation systems where certain I/O branches operate without an AUM Ensures reliable I/O communication in critical process control environments FAQ Q: Can this module be used on branches with an AUM?A: No, this module is specifically designed for branches without an AUM. Q: Does it support dual redundant power supplies?A: Yes, redundant power configurations are supported to enhance system reliability. Q: Are there installation restrictions regarding side placement?A: No, it can be installed on either side (A or B) of a standard I/O base. Similar Model Comparison Model Key Features Application 1B30023H02 No AUM terminator, supports redundant power, dual-side installation Local I/O branches without AUM 1B30024H01 Terminator with AUM support, standard power Branches with AUM 1B30025H03 High-temperature environment module High-temperature industrial applications
$200.00 $100.00
-
EMERSON EMERSON Ovation 1C31232G01 Digital Input Module | Oil Gas Control
Product Description OverviewThe EMERSON 1C31232G01 is a high-reliability digital input module designed for the Ovation™ Distributed Control System (DCS). Engineered for precision monitoring and control in demanding industrial environments, this module ensures accurate signal acquisition and seamless integration with existing Ovation control architectures. Technical Specifications Parameter Specification Model / Part Number 1C31232G01 Module Type Digital Input Weight 0.25 kg Input Channels 16 discrete inputs (typical for Ovation digital modules) Input Voltage Range 24V DC nominal (supports standard Ovation logic levels) Isolation Optical isolation between input and backplane Mounting DIN rail or rack-mount compatible Operating Temperature -20°C to +70°C Storage Temperature -40°C to +85°C Communication Interface Ovation DCS proprietary bus Status Indicators LED indicators for each input channel Condition New, factory-sealed original Key Features Reliable digital signal acquisition for Ovation DCS Compact and lightweight design for flexible installation Fully compatible with oil, gas, and power plant applications High durability under extreme industrial conditions ApplicationsIdeal for use in oil and gas production facilities, power generation plants, and industrial automation systems where accurate monitoring of discrete signals is critical. Supports both retrofits and new Ovation DCS installations. Similar Model Comparison 1C31231G01: 8-channel digital input module, smaller footprint 1C31233G01: 32-channel digital input module, higher channel density FAQ Q: Is the module compatible with older Ovation DCS versions?A: Yes, 1C31232G01 is backward compatible with most Ovation release versions while supporting standard communication protocols. Q: What is the typical delivery time for this module?A: Standard lead time is 2–3 business days with shipping from the USA.
$200.00 $100.00
-
EMERSON Emerson 1C31125G03 Digital I/O Module | Ovation DCS Interface
Product Description The 1C31125G03 from Emerson’s Ovation series is a high-precision digital I/O module designed for distributed control systems (DCS). It facilitates seamless communication between field devices and Ovation controllers, efficiently managing discrete input and output signals. The module supports both locally and remotely powered configurations, making it flexible for integration with relay modules or terminal blocks for field interfacing. Technical Specifications Manufacturer: Emerson (Ovation) Model / Part Number: 1C31125G03 Product Type: Digital I/O Module System Compatibility: Ovation DCS platforms Signal Type: Discrete input/output (digital) Interface Options: Connects to relay modules or field terminals Power Configuration: Supports remote power from relay modules Dimensions: 12.1 × 5.4 × 14 cm Weight: 0.3 kg Operating Temperature: -20°C to +70°C (typical industrial range) Mounting Type: Rack-mounted within DCS cabinet Country of Origin: USA Condition: New, with original packaging (when supplied) Warranty: 12 months (typical from suppliers) Applications The 1C31125G03 module is widely implemented in mission-critical industries including power generation, water treatment, and chemical process control. It provides reliable signal processing for Ovation controllers, supporting diagnostics, fault-tolerant operation, and real-time system monitoring. FAQ Q: What types of signals does the 1C31125G03 manage?A: It handles discrete input and output signals within Ovation DCS systems. Q: Can this module be used in critical applications?A: Yes, it is engineered for high-reliability applications such as power generation and industrial process control. Q: What is the standard warranty period?A: Most suppliers provide a 12-month warranty for this module. Q: How is the module powered?A: It can be powered remotely from connected relay modules or locally through field terminals. Comparison with Similar Models Ovation 1C31125G01: Similar I/O module but supports fewer discrete channels. Ovation 1C31125G05: Enhanced diagnostic features for critical monitoring.
$200.00 $100.00
-
EMERSON EPRO MMS6823R Analog Input Module | 24-Channel SIL2 Compliant
Product Description Overview The MMS6823R from EPRO is a high-performance analog input module designed to capture and process up to 24 analog signals simultaneously. Built for demanding industrial and safety applications, it delivers precise signal acquisition and supports SIL2 safety integrity standards. This compact module provides robust performance while maintaining a small footprint for seamless integration into control systems. Technical Specifications Channels: 24 analog input channels Signal Types: Compatible with standard voltage and current inputs (0–10 V, 4–20 mA) Safety Compliance: SIL2 certified for functional safety applications Input Resolution: 16-bit (high accuracy) Sampling Rate: Up to 1 kHz per channel Operating Voltage: 24 V DC ±10% Isolation: Channel-to-channel and channel-to-system isolation up to 250 V Dimensions: 6 × 19 × 13 cm Weight: 0.28 kg Mounting: DIN rail compatible Operating Temperature: –20°C to +60°C Storage Temperature: –40°C to +85°C Communication Interface: Standard industrial bus protocols supported (Modbus, CAN, PROFIBUS optional) Applications The EPRO MMS6823R is suitable for process control, industrial automation, safety monitoring, and systems requiring reliable analog signal acquisition with SIL2 compliance. It is ideal for integration into safety PLCs, SCADA systems, and redundant analog signal networks. Comparison with Similar Modules Compared to the MMS6816R, the MMS6823R provides double the channel count and enhanced SIL2 safety support. Offers higher input resolution and faster sampling rates than legacy models for more precise signal processing. FAQ Q: Can the MMS6823R handle both voltage and current inputs simultaneously?A: Yes, it supports standard voltage (0–10 V) and current (4–20 mA) signals across all 24 channels. Q: Is the module hot-swappable?A: No, it requires system power-down for safe installation and removal.
$200.00 $100.00
-
EMERSON Epro Emerson MMS6310 Dual-Channel Key Pulse Monitor | Signal Processor
Product Description Overview The Epro Emerson MMS6310 is a precision dual-channel key pulse monitor engineered for accurate pulse detection and advanced signal processing in industrial environments. It ensures reliable performance under variable electrical conditions, supporting high-speed signal monitoring for automated control systems. Electrical Specifications Input Resistance: Greater than 100 kΩ Input Voltage Range: 0 to ±27.3 VDC Maximum Permissible Input Voltage: 30 VDC Input Frequency Range: 0 to 20 kHz Trigger and Signal Processing Automatic and Manual Trigger Level Adjustment: Supported Minimum Input Level for Automatic Tracing: 2 V Signal Conditioning: Provides stable pulse output even under noisy inputs Output Features Key-Pulse Outputs: Two independent channels with open-collector configuration Pulse Type: Rectangular pulses inverted relative to input, galvanically isolated Pulse Duration: 1 ms Output Frequency Range: 0 to 20 kHz Applications Ideal for industrial automation, machine monitoring, data acquisition systems, and other scenarios requiring precise pulse detection and signal conditioning. FAQ Q: Can MMS6310 handle high-frequency signals beyond 20 kHz?A: No, the device is rated for input frequencies up to 20 kHz. Exceeding this may affect pulse accuracy. Q: Is galvanic isolation provided for outputs?A: Yes, both pulse outputs are galvanically isolated to prevent interference with connected systems. Q: How does automatic trigger level adjustment work?A: The unit continuously monitors input signals above 2 V and adjusts the trigger level for consistent pulse detection without manual intervention.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/05-02-04-00-00-01 Mini Rack PLC Chassis System
Product Overview The 3500/05-02-04-00-00-01 is a compact, rack-mount chassis from Bently Nevada’s 3500 machinery protection series. Designed for installations where space is limited, this mini-rack accommodates up to seven modules, providing the structural frame and electrical backplane for continuous machinery protection. Its rear-access wiring configuration simplifies installation in control cabinets and skid-mounted equipment. This chassis supports full integration of Rack Interface Modules (RIM), power supplies, monitors, relays, and communication modules, ensuring complete API‑670-compliant vibration monitoring for small-footprint systems. Technical Specifications Rack Format Type: Mini 3500 rack Mounting: 19-inch EIA rails, rack-mount Module slots: 7 total Reserved positions: 1 for RIM, 1 for power supply Remaining slots for monitors, relays, or communications Mechanical Dimensions: 178 mm H × 305 mm W × 305 mm D (~7 × 12 × 12 in) Material: Aluminum chassis Finish: Standard EIA (option 01) Wiring access: Rear Backplane / Electrical Type: Standard non-barrier Power: Single or dual redundant supply support Communication buses: System data bus, relay bus, Keyphasor and transducer routing Module compatibility: All standard 3500 series modules (within slot limits) Environmental Ratings Operating temperature: –20°C to +65°C Storage temperature: –40°C to +85°C Humidity: Up to 95% non-condensing Vibration: Industrial-grade, suitable for turbines, compressors, and refinery machinery Certifications EMC: EN 61000‑6‑2 (immunity), EN 61000‑6‑4 (emissions) Safety: EN 61010‑1 Hazardous area: Class I, Div 2, Groups A–D, T4; ATEX/IECEx Zone 2 Applications Compact turbine or compressor protection systems Skid-mounted machinery monitoring OEM equipment requiring integrated protection Small-footprint monitoring and condition-based maintenance Option Code Breakdown 02 — Mini-rack (7 slots) 04 — Rack-mount format 00 — Standard non-barrier backplane 00 — No internal barriers 01 — Standard EIA finish FAQ Q1: Can this mini-rack be installed in a standard 19-inch cabinet?Yes, it is designed for 19-inch EIA rail mounting with rear wiring access. Q2: How many modules can this mini-rack accommodate?Up to seven modules: 1 RIM, 1 power supply, and 5 for monitors, relays, or communication modules. Q3: Is it suitable for harsh industrial environments?Yes, it supports industrial vibration, temperature extremes, and electrical isolation for reliable monitoring.
$200.00 $100.00
-
ABB ABB INNPM11 Network Processing Communication Module
Product Description The ABB INNPM11 Network Processing Module is a core communication component used within ABB INFI-90 / Symphony distributed control architectures. It functions as a high-speed message processor responsible for data exchange between Controlway, Module Bus, and the INFI-NET network layer. Designed by ABB for deterministic control environments, this module ensures synchronized information flow between controller-level operations and plant-wide communication infrastructure. The INNPM11 operates in conjunction with the INNIS01 interface module to establish a complete communication pathway between process control units and the INFI-NET backbone. It manages cyclic data, exception reporting, system polling, and time synchronization across distributed nodes. Core Technical Specifications System Integration Platform: ABB INFI-90 / Symphony DCS Function: Network processing and protocol handling module Communication layers: Controlway, Module Bus, INFI-NET Network role: Message routing and synchronization processor Communication Performance Controlway speed: 1 Mbaud Module Bus speed: 83.3 kbaud INFI-NET: High-speed serial deterministic data highway Supported messaging: Broadcast, multicast, exception reporting, polling, time sync Processing & Memory RAM: 512 KB onboard memory ROM: 256 KB firmware storage Processing function: Real-time message scheduling and routing Electrical Characteristics Supply voltage: +5 VDC (backplane powered) Power consumption: approx. 10 W (2 A typical load) Isolation: Electrical separation between network and system backplane Mechanical Design Module type: INFI-90 standard plug-in card Dimensions: 27.9 cm × 7.6 cm × 5.1 cm Weight: 0.2 kg Installation: Standard ABB rack slot configuration Cooling: Passive convection within chassis Functional Role in System Architecture The INNPM11 acts as the central message handler for inter-layer communication inside INFI-90 systems. It ensures: Deterministic routing of control and process data Real-time synchronization between distributed controllers Exception-based data transmission for efficiency Stable communication across redundant network topologies Coordination between Controlway-level and plant-level networks Application Areas Distributed process control system communication backbone Real-time controller coordination in industrial plants Data synchronization between HMI and controller networks Integration layer for SCADA and engineering stations High-availability automation system architectures FAQ Q1: What is the primary role of INNPM11?It processes and routes communication between Controlway, Module Bus, and INFI-NET networks in INFI-90 systems. Q2: Does INNPM11 support redundancy?Yes, it is designed to operate within redundant INFI-NET system configurations. Q3: Is it compatible with modern SCADA systems?It can interface through gateway modules for SCADA and historian integration within legacy ABB infrastructures.
$200.00 $100.00
-
ABB ABB INICT13 INFI-NET Computer Transfer Gateway Module
Product Description The ABB INICT13 INFI-NET Computer Transfer Module is a high-integrity communication interface designed for ABB INFI-90 / Symphony distributed control environments. It functions as a deterministic data bridge between the INFI-NET control network and external computing platforms such as operator stations, engineering systems, and plant data servers. Developed by ABB for mission-critical industrial automation infrastructures, this module is optimized for redundant network architectures where continuous data availability and fault tolerance are required. Unlike earlier INICT generations, the INICT13 features improved processing throughput, enhanced diagnostic reporting, and more stable host communication performance under high network load conditions. It is typically deployed as part of an N-Module rack system and operates within a token-passing INFI-NET architecture, ensuring predictable communication timing and system-wide synchronization. Technical Specifications Network Communication Network architecture: INFI-NET redundant token-passing system Function: Bidirectional gateway between control network and host systems Data types supported: Real-time process variables Alarm and event records System diagnostics and status information Configuration and engineering data Host integration: HMI, SCADA, engineering workstations, historians Electrical Characteristics Backplane supply: +5 VDC (rack-powered) Typical power consumption: 8–12 W Electrical isolation: Network-to-backplane isolation for noise protection Environmental Limits Operating temperature: 0°C to +60°C Storage temperature: –40°C to +85°C Relative humidity: 5–95% non-condensing Cooling method: Passive convection within N-Module chassis Mechanical Design Module format: ABB N-Module plug-in card Mounting: Standard INFI-90 / Symphony rack slot Front panel indicators: Power, network activity, redundancy status LEDs Hot-swap capability: Supported in compatible rack configurations Key Functions Acts as a deterministic gateway between INFI-NET and external computer systems Maintains synchronized data flow in redundant control networks Supports continuous alarm and event propagation to host platforms Enables real-time plant monitoring and supervisory control integration Provides system diagnostics visibility for maintenance and engineering teams System Integration Notes Designed for ABB INFI-90 / Symphony system architecture Compatible with legacy INFI-NET infrastructure upgrades Supports integration with SCADA and historian platforms Works alongside other INICT family modules such as INICT01 and INICT03, offering improved throughput and stability in newer installations Application Scenarios Industrial SCADA system integration for centralized monitoring HMI workstation connectivity in distributed control systems Plant historian data acquisition and archiving Engineering station access for configuration and diagnostics Third-party system interoperability in hybrid automation environments FAQ Q1: Is the INICT13 backward compatible with older INFI-NET systems?Yes, it is designed to operate within existing INFI-NET infrastructures while improving performance and stability. Q2: Does the module support redundancy?Yes, it fully supports redundant INFI-NET network configurations for high availability systems. Q3: Can it be hot-swapped?In supported N-Module racks, the module can be replaced without full system shutdown.
$200.00 $100.00
-
ABB ABB INICT03 Computer Network Interface Module
Product Overview The ABB INICT03A INICT03 module is a communication interface designed for ABB INFI-90 / Symphony distributed control systems. It connects the INFI-NET control network with external computer systems including operator workstations, engineering stations, and data servers. It is installed in an ABB N-Module rack and functions as a central data exchange node, enabling plant-wide access to real-time process information and system status. System Function Description This module operates as a network bridge between the INFI-NET token-passing control network and host computing platforms. It supports continuous and synchronized data exchange across industrial automation layers. Main functions include Transfer of real-time process values from controllers to host systems Transmission of alarms and event messages for supervisory monitoring Delivery of system diagnostics and status information Bidirectional communication for configuration and control support It is commonly used in SCADA systems, historians, and engineering environments where reliable data access is required. Technical Specifications Communication Interface Network Type: INFI-NET redundant token-passing architecture Communication Mode: Bidirectional data transfer Data Types: Process values, alarms, events, diagnostics System Integration: HMI, SCADA, historian, engineering tools Electrical Characteristics Power Supply: +5 VDC via N-Module backplane Power Consumption: Approximately 10 W Mechanical Design Module Type: ABB N-Module plug-in card Mounting: INFI-90 / Symphony rack compatible Connector Type: Backplane edge connector Indicators: LED status for network and module diagnostics Environmental Conditions Operating Temperature: 0°C to 60°C Storage Temperature: -40°C to 85°C Humidity: 5% to 95% non-condensing Cooling: Natural convection within rack Physical Data Weight: 2.01 lbs Key Features Provides communication bridge between control network and computer systems Supports redundant INFI-NET architecture Enables deterministic real-time data exchange Designed for continuous industrial operation Compatible with rack-based hot-swap configurations depending on system setup Application Areas Distributed control system integration Plant monitoring and visualization systems SCADA supervisory control environments Engineering configuration stations Industrial data acquisition and historian systems
$200.00 $100.00
-
ABB ABB IMRI002 Remote I/O Slave Module
Overview The IMRIO02 is a remote I/O slave interface module designed for ABB Bailey INFI-90 and Network 90 distributed control platforms. It functions as a communication node that collects field-level I/O signals from remote termination units and transfers process data to the central controller through ABB’s proprietary Remote I/O network. This module is intended for rack-based N-Series installations used in legacy ABB distributed control environments requiring extended I/O reach and stable deterministic communication. System Role and Function The IMRIO02 operates as a dedicated remote I/O communication interface within the INFI-90 architecture, supporting: Aggregation of distributed analog and digital I/O signals Real-time data exchange with the main controller System diagnostics reporting for remote I/O segments Coordination of multi-drop I/O network communication Integration with ABB N-Series rack-based termination hardware Communication Characteristics Protocol: ABB proprietary Remote I/O (RIO) bus Network structure: Multi-drop distributed I/O topology Data exchange: Cyclic process data plus diagnostic messaging Integration scope: INFI-90 / Network 90 control systems Compatibility: ABB N-Module rack and field termination assemblies Electrical Specifications Supply voltage: 5 VDC via rack backplane Power consumption: approximately 5–8 W typical Interface type: High-speed backplane communication connection Electrical isolation: Provided at system rack level Mechanical Construction Module format: ABB N-Series plug-in card design Installation method: Standard INFI-90 rack slot mounting Weight: 0.85 lbs Front panel: LED indicators for module status and communication activity Cooling: Passive convection within rack enclosure Environmental Limits Operating temperature: 0°C to 60°C Storage temperature: -40°C to 85°C Humidity range: 5% to 95% non-condensing Designed for continuous industrial duty operation Application Areas Thermal and hydro power generation control systems Refinery and petrochemical process automation Heavy industrial distributed control systems Legacy ABB DCS maintenance and spare part replacement Expansion of remote I/O capacity in existing INFI-90 installations
$200.00 $100.00
-
ABB ABB IMMFP03R Multi-Function Processor Module
Product Description The IMMFP03R is a high-performance control processor designed for ABB Bailey INFI 90 and Net 90 distributed control architectures. It functions as the central execution unit responsible for real-time control processing, system coordination, and communication management across I/O subsystems. Engineered with redundancy capability, this module supports hot-standby configuration, allowing continuous operation in mission-critical environments such as power generation units, refining facilities, and large-scale process plants. Core Processing Functions Executes regulatory control algorithms (PID and advanced loop control) Handles sequential logic and batch process execution Manages real-time I/O data acquisition and processing Supports peer-to-peer communication across INFI 90 networks Coordinates system-wide control strategy execution Operates as primary or backup controller in redundant setups System Architecture & Redundancy Redundancy type: Hot-standby dual-module configuration Failover behavior: Automatic switchover in sub-second range Synchronization: Continuous state mirroring between paired controllers Communication backbone: INFI-NET high-speed control network Designed for uninterrupted process operation in critical systems Memory & Processing Resources 32-bit industrial processor architecture Program memory: EPROM / Flash-based storage Runtime memory: RAM with battery-backed retention Non-volatile memory support for configuration and logic retention Deterministic scan-based execution cycle for real-time control Communication Capabilities INFI-NET system-wide communication bus Direct module bus interface to INFI 90 I/O racks Supports analog, digital, and specialty I/O modules Peer-to-peer data exchange between controllers Integrated diagnostics and communication watchdog monitoring Electrical Characteristics Logic supply: +5 V DC (~2–3 A typical load) Auxiliary supply: +24 V DC (~0.1–0.2 A typical load) Backplane-powered architecture Internal isolation for signal integrity and noise suppression Power-efficient design (~10 W typical consumption) Environmental Specifications Operating temperature: 0°C to +60°C Storage temperature: –40°C to +85°C Relative humidity: 5–95% non-condensing Industrial-grade EMI/EMC resistance for harsh environments Physical Design Standard ABB INFI 90 rack-mounted processor format Dimensions: 350 × 260 × 70 mm Weight: 1.2 kg Installed directly into INFI 90 system chassis slot Application Areas Thermal and nuclear power generation control systems Petrochemical refining process automation Water treatment and utility control networks Continuous industrial production environments High-availability distributed control systems FAQ What does the “R” in IMMFP03R mean?It indicates redundancy support, enabling hot-standby operation with a paired controller. Can this module operate alone?Yes, it can function as a single controller, but redundancy is recommended for critical systems. Is it compatible with all INFI 90 I/O modules?Yes, it supports full integration with standard INFI 90 analog, digital, and specialty I/O modules.
$200.00 $100.00
You have seen 24 out of 1730 products