The Bently Nevada 3300 Series delivers precise rotor and machinery monitoring. Our inventory provides sensors, probes, and spare parts for both current and legacy systems.
Bently Nevada 3300 Series
-
Bently Nevada Bently Nevada | 330104‑00‑06‑90‑02‑00 | 3300 XL 8 mm Proximity Probe
Overview The Bently Nevada 330104‑00‑06‑90‑02‑00 proximity probe is part of the 3300 XL 8 mm transducer family and is engineered for long‑distance installations requiring stable displacement and vibration measurements. This model incorporates a 9.0‑meter probe cable, making it suitable for machinery layouts where extended routing is necessary without compromising signal integrity. Key Characteristics Model: 330104‑00‑06‑90‑02‑00 Probe Type: 8 mm proximity probe with FluidLoc cable Thread Specification: M10 × 1 Minimum Case Length: 60 mm Cable Length: 9.0 m (29.5 ft) Connector: Miniature coaxial ClickLoc System Compatibility: 3300 Proximity Transducer System Certifications: CSA, ATEX, IECEx Condition: New Weight: 0.08 kg Dimensions: 2 × 1.5 × 122 cm Functional Description The 330104‑00‑06‑90‑02‑00 probe uses an eddy‑current sensing coil to measure the distance between the probe tip and a conductive target surface. Its extended 9‑meter cable allows installation flexibility in large machinery skids, turbine decks, or compressor trains. The FluidLoc cable design prevents oil migration through the cable jacket, improving long‑term reliability in lubrication‑rich environments. The ClickLoc connector ensures a secure mechanical lock, preventing accidental loosening under vibration. When paired with the appropriate extension cable and Proximitor sensor, the probe forms a calibrated measurement chain compliant with API 670 requirements. Technical Specifications Mechanical Parameter Value Probe Tip Diameter 8 mm Thread Type M10 × 1 Case Length ≥ 60 mm Cable Length 9.0 m Cable Type FluidLoc, oil‑resistant Connector Miniature coaxial ClickLoc Weight 0.08 kg Shipping Dimensions 2 × 1.5 × 122 cm Electrical Parameter Value Sensitivity 7.87 V/mm (200 mV/mil) typical Linear Range 2 mm (80 mil) Frequency Response DC to 10 kHz System Compatibility 3300 XL Proximity System Grounding Single‑point shield grounding recommended Environmental Parameter Value Operating Temperature –35°C to +177°C (probe only) Humidity 95% non‑condensing Certifications CSA, ATEX, IECEx RFI/EMI Immunity Meets CE requirements Applications Turbines (steam, gas, hydro) Compressors and expanders High‑speed motors and generators Gearboxes and critical rotating assets API 670‑compliant vibration protection systems FAQ Q: Can this probe be used with non‑XL 3300 systems? A: No. It must be paired with 3300 XL extension cables and Proximitor sensors to maintain calibration accuracy. Q: What advantage does the FluidLoc cable provide? A: It prevents oil ingress through the cable jacket, improving reliability in lubrication‑intensive environments. Q: Is field calibration required? A: No. The probe, extension cable, and Proximitor sensor are factory‑matched and do not require bench calibration.
$200.00 $100.00
-
Bently Nevada Bently Nevada | 330103‑00‑06‑05‑02‑05 | 3300 XL 8 mm Proximity Probe
Overview The Bently Nevada 330103‑00‑06‑05‑02‑05 proximity probe is part of the 3300 XL 8 mm transducer family, engineered for precise shaft vibration and position measurements in rotating machinery. This probe assembly is designed for long‑term stability, high linearity, and reliable operation in electrically noisy industrial environments. Key Features Probe Model: 330103‑00‑06‑05‑02‑05 Probe Type: 8 mm unarmored proximity probe Thread Specification: M10 × 1 Minimum Case Length: 60 mm Cable Length: 0.5 m (1.6 ft), miniature coaxial ClickLoc connector System Compatibility: 3300 XL Proximity Transducer System Certifications: CSA, ATEX, IECEx RFI/EMI Performance: Enhanced immunity suitable for fiberglass housings without shielded conduit Operating Principle: Eddy‑current displacement measurement Typical Applications: Shaft vibration, axial position, phase reference, and radial clearance monitoring Technical Specifications Mechanical Parameter Value Probe Tip Diameter 8 mm Thread Type M10 × 1 Case Length ≥ 60 mm Cable Length 0.5 m Connector Type Miniature coaxial ClickLoc Weight 0.06 kg Shipping Dimensions 115 × 2.5 × 1.5 cm Electrical Parameter Value Sensitivity 7.87 V/mm (200 mV/mil) typical Linear Range 2 mm (80 mil) Frequency Response DC to 10 kHz System Compatibility 3300 XL Proximity System (Probes + Extension Cable + Proximitor) Grounding Single‑point shield grounding recommended Environmental Parameter Value Operating Temperature –35°C to +177°C (probe only) Humidity 95% non‑condensing Certifications CSA, ATEX, IECEx RFI/EMI Immunity Meets CE requirements without metallic conduit Functional Description The 330103‑00‑06‑05‑02‑05 probe uses an eddy‑current sensing coil to detect the distance between the probe tip and a conductive target surface, typically a rotating shaft. Its improved electromagnetic shielding allows installation in non‑metallic housings without performance degradation. The ClickLoc connector ensures secure attachment to extension cables, preventing accidental loosening under vibration. The probe is optimized for use with the 3300 XL Proximitor sensor, forming a calibrated measurement chain that delivers stable displacement and vibration readings across a wide temperature range. Applications Steam and gas turbines Compressors and expanders Motors and generators Gearboxes and pumps API 670‑compliant vibration protection systems FAQ Q: Can this probe be mixed with older 7200 series components? A: No. Mixing 3300 XL probes with older systems results in incorrect calibration and is not recommended. Q: Does the probe require metallic conduit for CE compliance? A: No. Its enhanced RFI/EMI immunity allows installation in fiberglass or non‑metallic housings. Q: Is the probe suitable for high‑temperature zones?
$200.00 $100.00
-
Bently Nevada Bently Nevada 22810-00-06-10-02 3300 XL Proximity Probe
Product Overview The Bently Nevada 22810-00-06-10-02 3300 XL Proximity Probe delivers precise vibration monitoring for critical rotating machinery. Its 316 stainless steel housing ensures durability, while the M10 × 1 threaded design secures installation across diverse applications. Operators rely on this probe for consistent diagnostics in turbines, compressors, and pumps. Technical Specifications Parameter Value Model Number 22810-00-06-10-02 Module Type 3300 XL Proximity Probe Manufacturer Bently Nevada Product Series 3300 XL Condition Brand New Dimensions 20.4 × 22.2 × 3.7 cm Weight 0.12 kg HS Code 8537101190 System TSI Communication Service Ethernet Router Minimum Order Quantity 1 Origin USA Lead Time In Stock Status Active Cable Length 6.0 m (19.7 ft) Frequency Response 0–10 kHz (±3 dB) Sensitivity 7.87 V/mm (200 mV/mil ±5%) Thread Type M10 × 1 Stainless Steel Functional Description The 22810-00-06-10-02 probe features a wide frequency response range from 0 to 10 kHz, enabling detailed vibration analysis. Its sensitivity rating of 7.87 V/mm ensures accurate output for machinery diagnostics. The 6.0 m cable length provides installation flexibility, even in complex layouts. Compact packaging dimensions of 20.4 × 22.2 × 3.7 cm simplify handling and storage. Applications and Compatibility The 22810-00-06-10-02 3300 XL Proximity Probe integrates seamlessly with Bently Nevada monitoring systems, supporting predictive maintenance and centralized diagnostics. It suits industries such as power generation, petrochemical, and manufacturing, where continuous vibration monitoring is essential. Compatibility with the 3300 XL series ensures easy upgrades and replacements without modification.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330101‑33‑66‑10‑02‑05 | 3300 XL Series | 8 mm Proximity Probe
Overview The 330101‑33‑66‑10‑02‑05 proximity probe from Bently Nevada’s 3300 XL 8 mm series is engineered for precise shaft vibration and position measurement in rotating machinery. Designed for long‑term stability in harsh industrial environments, it integrates seamlessly with the 3300 XL Proximitor Sensor to deliver consistent, high‑accuracy displacement monitoring. Key Features 8 mm tip for standard industrial proximity measurements Unarmored probe design for flexible routing 3/8‑24 UNF mounting thread for secure installation Miniature coaxial ClickLoc connector for reliable electrical contact Compatible with 3300 XL Proximitor Sensors Enhanced immunity to RFI/EMI interference Certified to CSA, ATEX, and IECEx requirements Suitable for gas compressors, turbines, pumps, and general rotating equipment Technical Specifications Parameter Specification Model 330101‑33‑66‑10‑02‑05 Probe Type 3300 XL 8 mm Proximity Probe Thread Size 3/8‑24 UNF Cable Length 1.0 m Connector Miniature coaxial ClickLoc System Compatibility 3300 Proximity Transducer System Certifications CSA, ATEX, IECEx Weight 0.04 kg Dimensions 110 × 1.5 × 1.2 cm Origin USA Condition Brand New HS Code 8537101190 System TSI Status Active production Functional Characteristics The 330101‑33‑66‑10‑02‑05 probe is optimized for applications requiring stable gap measurement and vibration monitoring. Its mechanical design minimizes thermal drift and ensures consistent sensitivity across a wide temperature range. When paired with the 3300 XL Proximitor Sensor, the system provides linear output over the full measurement range and supports installation in metallic or non‑metallic housings without interference. Application Scenarios Gas compressor radial and axial vibration monitoring Turbine shaft displacement measurement Pump bearing housing vibration analysis Gearbox shaft position tracking Condition monitoring and predictive maintenance systems Similar Models Comparison Model Cable Length Thread Type Application Notes 330101‑00‑12‑10‑02‑00 0.5 m 3/8‑24 UNF Compact installations 330101‑33‑66‑10‑02‑05 1.0 m 3/8‑24 UNF Standard compressor applications 330103‑00‑12‑10‑02‑00 5 m M10 × 1 Long‑distance routing FAQ Q: Can this probe be used with older 7200 series proximitor modules? A: It is designed for the 3300 XL system. Compatibility with legacy systems may require verification of scale factors and calibration. Q: Is the probe suitable for hazardous areas? A: Yes, it carries CSA, ATEX, and IECEx certifications. Q: Does the probe include the proximitor sensor? A: No, the proximitor sensor is purchased separately.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330704‑010‑060‑10‑11‑00 | 3300 XL Series | 11 mm Proximity Probe
Overview The 330704‑010‑060‑10‑11‑00 proximity probe is part of Bently Nevada’s 3300 XL 11 mm transducer family, designed for high‑accuracy displacement and vibration measurement in large rotating machinery. This probe assembly is optimized for applications requiring extended linear range and enhanced sensitivity, making it suitable for turbines, compressors, and other fluid‑film bearing equipment. Design and Construction This model features an M14×1.5 threaded probe body with a 60 mm overall length and a minimum 10 mm unthreaded section. The probe includes a 1‑meter armored cable for mechanical protection in harsh environments. Its 11 mm tip design provides a wider linear range than 8 mm probes, enabling more accurate monitoring of slow‑speed or high‑displacement machinery. The assembly incorporates FluidLoc cable technology to prevent oil ingress and uses a miniature coaxial ClickLoc connector for secure, tool‑free installation. Stainless steel armor (indicated by “10” in the part number) ensures long‑term durability in high‑vibration environments. Technical Specifications Parameter Specification Model 330704‑010‑060‑10‑11‑00 Product Type 11 mm Proximity Probe Probe Tip Diameter 11 mm Thread Type M14 × 1.5 Probe Length 60 mm Unthreaded Length 10 mm minimum Cable Length 1.0 m Sensitivity 3.94 V/mm (100 mV/mil) Connector Type Miniature ClickLoc Cable Protection Stainless steel armor Temperature Range –51°C to +177°C Certifications ATEX, IECEx, CSA System Compatibility 3300 XL Proximity Transducer System Dimensions 115.5 × 2.5 × 2 cm Weight 0.16 kg Origin USA HS Code 8537101190 Product Status Active Functional Characteristics Extended linear range for large‑displacement machinery High sensitivity for accurate shaft position and vibration measurement FluidLoc cable design for oil‑rich environments ClickLoc connectors with positive locking feedback Stainless steel armored cable for mechanical protection Full compatibility with 3300 XL monitoring systems Application Scenarios Axial thrust position monitoring in steam turbines Differential expansion measurement Reciprocating compressor rod position detection Keyphasor signal generation Slow‑speed machinery requiring extended measurement range Model Comparison Model Probe Tip Cable Length Protection Typical Use 330704‑010‑060‑10‑11‑00 11 mm 1 m Armored High‑displacement machinery 330704‑000‑060‑10‑11‑00 11 mm 5 m Armored Long‑distance routing 330705‑02‑18‑10‑02‑00 8 mm 1.8 m Unarmored Standard vibration monitoring FAQ Q: What advantages does the 11 mm probe offer over 8 mm versions? A: The 330704‑010‑060‑10‑11‑00 provides a wider linear range, making it ideal for slow‑speed or large‑movement machinery. Q: Can this probe be used in hazardous areas? A: Yes. It is certified under ATEX, IECEx, and CSA standards. Q: Does the probe require calibration during installation? A: No. It is factory‑matched with its extension cable and driver, eliminating field calibration.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330102‑00‑28‑10‑02‑05 | 3300 XL Series | 8 mm Proximity Probe
Overview The 330102‑00‑28‑10‑02‑05 proximity probe is part of Bently Nevada’s 3300 XL 8 mm transducer family, engineered for precise shaft displacement and vibration measurement in rotating machinery. Designed for integration into the 3300 Proximity Transducer System, it provides stable, repeatable performance in demanding industrial environments where accurate condition monitoring is essential. Design and Construction This model features a 3/8‑24 UNF threaded probe body and a factory‑matched cable assembly to maintain linearity and measurement accuracy. The probe includes a standard 1.0‑meter cable and a Miniature ClickLoc connector, ensuring secure, corrosion‑resistant connections. Armored cable protection enhances durability in high‑vibration or abrasive environments, while optional FluidLoc technology prevents oil ingress in lubrication‑rich applications. Technical Specifications Parameter Specification Model 330102‑00‑28‑10‑02‑05 Product Type 8 mm Proximity Probe Probe Tip Diameter 8 mm Thread Type 3/8‑24 UNF Cable Length 1.0 m Connector Type Miniature ClickLoc Pull Strength 330 N (75 lbf) Temperature Range –51°C to +177°C Certifications ATEX, IECEx, CSA System Compatibility 3300 XL Proximity Transducer System Dimensions 20.4 × 22.2 × 3.7 cm Weight 0.15 kg Origin USA HS Code 8537101190 Product Status Active Functional Characteristics High‑accuracy displacement and vibration measurement for critical rotating equipment TipLoc and CableLoc construction for improved mechanical integrity Gold‑plated ClickLoc connectors with audible locking feedback Full interchangeability with other 3300 XL 8 mm components Suitable for hazardous areas with global safety approvals No recalibration required when replacing matched components Application Scenarios Turbines, compressors, and high‑speed pumps Shaft position and radial vibration monitoring Machinery protection systems in power generation and petrochemical plants Environments requiring armored or fluid‑resistant cable assemblies Model Comparison Model Probe Tip Cable Length Protection Typical Use 330102‑00‑28‑10‑02‑05 8 mm 1.0 m Armored Standard industrial machinery 330102‑00‑12‑10‑02‑05 8 mm 5 m Armored Long‑distance routing 330103‑00‑04‑10‑02‑05 5 mm 1 m Unarmored Tight‑clearance installations FAQ Q: Does this probe require calibration before installation? A: No. The 330102‑00‑28‑10‑02‑05 is factory‑matched with its extension cable and driver, eliminating field calibration. Q: Can it be used in hazardous areas? A: Yes. It carries ATEX, IECEx, and CSA certifications. Q: Is the probe compatible with older 3300 systems? A: It is fully compatible with the 3300 XL system and supports backward compatibility with selected 5 mm and 8 mm components.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330101‑00‑25‑10‑02‑05 | 3300 Series | Proximity Probe Assembly
Overview The 330101‑00‑25‑10‑02‑05 proximity probe assembly is part of Bently Nevada’s 3300 XL 8 mm transducer family, engineered for precise vibration and shaft position measurement in rotating machinery. This probe and extension cable set is designed for compatibility with the 3300 XL system architecture and supports high‑accuracy condition monitoring in demanding industrial environments. Design and Performance This model incorporates an 8 mm probe tip and a factory‑matched extension cable to ensure consistent linearity and measurement accuracy. The assembly adheres to API 670 requirements for mechanical configuration, linear range, and temperature stability. Its rugged construction supports long‑term operation in harsh conditions, including wide temperature swings and high mechanical stress. The probe system is fully interchangeable with other 3300 XL 8 mm components, eliminating the need for individual calibration and simplifying maintenance workflows. The ClickLoc‑style coaxial connectors provide secure, vibration‑resistant connections during installation and operation. Technical Specifications Parameter Specification Model 330101‑00‑25‑10‑02‑05 Product Type Proximity Probe + Extension Cable Probe Tip Diameter 8 mm Cable Length 1.0 m (extension cable) System Compatibility 3300 XL 8 mm Proximity Transducer System Linear Range Typically 2 mm (dependent on system configuration) Frequency Response Suitable for high‑speed rotating equipment Temperature Range –51°C to +177°C Connector Type Miniature coaxial (ClickLoc) Compliance API 670 (4th Edition) Dimensions 110 × 1.5 × 1.2 cm Weight 0.23 kg Origin USA HS Code 8537101190 Product Status Active Functional Characteristics Stable displacement and vibration measurement for fluid‑film bearing machines Armored and unarmored cable options for different installation environments High immunity to electrical noise and mechanical interference Backward compatibility with selected 3300 5 mm and 8 mm components No field calibration required due to matched probe‑cable‑driver configuration Application Scenarios Turbomachinery vibration monitoring Shaft position and radial displacement measurement Condition monitoring systems in power generation, petrochemical, and refining industries Machinery protection systems requiring API 670 compliance Model Comparison Model Probe Tip Cable Length Compatibility Typical Use 330101‑00‑25‑10‑02‑05 8 mm 1.0 m 3300 XL Standard vibration monitoring 330101‑00‑12‑10‑02‑05 8 mm 5 m 3300 XL Long‑distance installations 330103‑00‑04‑10‑02‑05 5 mm 1 m 3300 XL Tight‑clearance machinery FAQ Q: Does this probe require calibration before installation? A: No. The 330101‑00‑25‑10‑02‑05 is factory‑matched with its cable and driver, eliminating field calibration. Q: Can it be used with older 3300 series systems? A: Yes, it supports backward compatibility with selected 5 mm and 8 mm components. Q: Is the probe suitable for high‑temperature environments? A: Yes. It is rated for continuous operation up to +177°C.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330130-085-03-00 Extension Cable
Product Overview The Bently Nevada 330130-085-03-00 Extension Cable enhances the 3300 XL Proximity Transducer System with an 8.5-meter armored construction. Its integrated connector protector ensures secure data transmission while resisting mechanical stress and environmental contaminants. Compact dimensions of 20.2 × 22.2 × 3.5 cm and a weight of 0.34 kg make it suitable for demanding industrial environments. Technical Specifications Parameter Value Model Number 330130-085-03-00 Module Type Extension Cable Manufacturer Bently Nevada Product Series 3300 XL Proximity Transducer System Condition Brand New Dimensions 20.2 × 22.2 × 3.5 cm Weight 0.34 kg HS Code 8537101190 System TSI Communication Service Ethernet Router Minimum Order Quantity 1 Origin USA Lead Time In Stock Status Active Cable Length 8.5 m Armored Connector Protection Integrated Protector Mounting Options DIN-rail or Panel Functional Description The 330130-085-03-00 cable maintains signal integrity over extended runs, ensuring accurate vibration data transmission. Its armored jacket protects against abrasion, chemicals, and mechanical damage, while the connector protector prevents contamination. Engineers benefit from flexible installation options, including DIN-rail or panel mounting, making this cable ideal for complex machinery layouts. Applications and Compatibility The 330130-085-03-00 Extension Cable integrates seamlessly with both standard and NSv Proximitor Sensors. It suits industries such as power generation, oil and gas, and heavy manufacturing, where long cable runs are required. Compatibility with the 3300 XL series ensures reliable performance and simplifies system upgrades.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330180-10-05 3300 XL Proximitor Sensor
Product Overview The Bently Nevada 330180-10-05 Proximitor Sensor belongs to the 3300 XL Proximity Transducer System. This 1.0-meter panel-mount sensor ensures precise vibration and position monitoring in turbines, compressors, pumps, and generators. Its compact dimensions and lightweight design simplify installation while maintaining superior electrical isolation. Technical Specifications Parameter Value Model Number 330180-10-05 Module Type 3300 XL Proximitor Sensor Manufacturer Bently Nevada Product Range 3300 Proximity Transducer System Condition Brand New Dimensions 8.8 × 3.5 × 7 cm Weight 0.22 kg HS Code 8537101190 Minimum Order Quantity 1 Origin USA System TSI Communication Service Ethernet Router Status Active Certifications CSA, ATEX, IECEx, CE Probe Compatibility 5 mm and 8 mm proximity probes Mounting Options DIN-rail or panel-mount, 4-hole footprint Functional Description The 330180-10-05 sensor incorporates SpringLoc terminal strips that enable tool-free, vibration-resistant wiring connections. Its enhanced RFI/EMI immunity meets CE mark requirements, allowing installation in fiberglass enclosures without shielded conduit. The sensor eliminates the need for isolator plates, reducing installation complexity while ensuring reliable electrical isolation. Applications and Compatibility The Bently Nevada 330180-10-05 Proximitor Sensor supports critical machinery monitoring in hazardous environments. CSA, ATEX, and IECEx certifications guarantee safe operation. Compatibility with both 5 mm and 8 mm proximity probes provides flexibility for diverse monitoring applications. Operators integrate it easily into legacy systems thanks to its standardized 4-hole footprint. Key Benefits Compact 8.8x3.5x7cm dimensions simplify installation in restricted spaces. Lightweight 0.22kg design improves handling and replacement efficiency. SpringLoc terminals eliminate screw-type connections, enhancing reliability. Certified for hazardous areas, ensuring global compliance and safety. Backward compatibility supports legacy 3300 series installations.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330105-02-12-02-05-00 3300 XL 8 mm Reverse Mount Probe
Product Overview The Bently Nevada 330105-02-12-02-05-00 Reverse Mount Probe belongs to the 3300 XL series, engineered for precise vibration and position monitoring. Its armored 1.0 meter cable with Miniature ClickLoc coaxial connector ensures secure installation and reliable signal transmission. Operators use this probe to measure static position and dynamic vibration in turbines, compressors, and pumps. Technical Specifications Parameter Value Model Number 330105-02-12-02-05-00 Module Type 3300 XL 8 mm Reverse Mount Probe Manufacturer Bently Nevada Product Series 3300 Proximity Transducer System Condition Brand New Dimensions 21 × 20 × 2 cm Weight 0.32 kg HS Code 8537101190 System TSI Communication Service Ethernet Router Minimum Order Quantity 1 Origin USA Lead Time In Stock Status Active Cable Length 1.0 m Armored Connector Type Miniature ClickLoc Coaxial Temperature Range -51°C to +177°C Certifications CSA, ATEX, IECEx Compliance API 670 (4th Edition) Functional Description The 330105-02-12-02-05-00 probe generates voltage outputs proportional to the distance between its tip and target surface. Its advanced eddy current technology ensures superior linear range, temperature stability, and measurement accuracy. The probe eliminates the need for component matching or bench calibration, reducing installation time and maintenance requirements. Engineers rely on the 330105-02-12-02-05-00 for hazardous environments, thanks to CSA, ATEX, and IECEx certifications. Its armored construction withstands extreme industrial conditions, ensuring durability and long-term reliability. Applications and Compatibility The 330105-02-12-02-05-00 Reverse Mount Probe integrates seamlessly with Bently Nevada monitoring systems, supporting predictive maintenance and centralized diagnostics. It suits industries such as power generation, petrochemical, and manufacturing. Compatibility with the 3300 series ensures easy upgrades and interchangeability with probes, extension cables, and Proximitor sensors.
$200.00 $100.00
-
Bently Nevada Bently Nevada 106765-07 Interconnect Cable
Bently Nevada 106765-07 Interconnect Cable Configured for signal transmission continuity in TSI monitoring networks, the Bently Nevada 106765-07 (106765-07 Interconnect Cable) provides direct electrical interconnection between proximity transducer assemblies and associated monitoring hardware within the 3300 Proximity Transducer System. The cable assembly supports stable low-noise signal transport for vibration and shaft position monitoring loops operating under continuous machine protection conditions. Suffix Breakdown & Model Matrix The supplied documentation identifies a fixed catalog model only. No manufacturer-defined suffix matrix or configurable ordering structure was provided for the 106765-07 assembly. Hardware Specifications Parameter Specification Model 106765-07 Brand Bently Nevada Module Type Interconnect Cable Product Series 3300 Proximity Transducer System System Compatibility TSI Origin USA Weight 0.38 kg Dimensions 20.5 x 22 x 3 cm Operating Temp -40 deg C to +150 deg C Voltage Rating 300 VAC/DC Current Rating 3 A to 7 A Conductor Size Approx. 0.22 mm2 Insulation Material High-temperature polymer Communication Service Ethernet router HS Code 8537101190 Product Status Active Power Consumption Passive cable assembly; no independent power consumption specified Eddy-Current Probe Signal Integrity Characteristics The 106765-07 interconnect cable is intended for proximity transducer signal routing where stable probe extension characteristics and low interference coupling are required. In TSI installations, cable routing directly affects eddy-current probe scaling accuracy and gap voltage stability relative to standard -10 VDC target calibration references. Shield continuity and controlled conductor impedance assist in reducing cross-talk between adjacent vibration channels during parallel tray installation. Separation from high-energy motor leads and VFD output cabling is recommended to minimize induced noise within rotor dynamic measurement circuits. The cable insulation system supports elevated ambient exposure near turbine bearing housings, compressor casings, and machinery pedestal installations where thermal gradients may exceed standard control cabinet conditions. Frequently Asked Questions Q: Does the 106765-07 interconnect cable require independent field power?A: No. The assembly functions as a passive signal interconnect component and does not require independent external power input. Q: Can the cable be routed in the same conduit as high-voltage motor conductors?A: Dedicated routing is recommended for proximity transducer circuits. Separation from high-current AC conductors reduces electromagnetic interference and minimizes signal distortion affecting vibration and gap measurements. Q: Is shield grounding required at both cable ends?A: Standard instrumentation grounding practice typically uses single-point shield grounding to reduce ground loop current circulation. Final grounding implementation should follow the TSI system installation standard and site electrical specification. Field Installation Guidelines Before installation, verify connector integrity, conductor insulation condition, and shield continuity using standard low-voltage continuity testing methods. Avoid excessive cable bending near termination points to prevent conductor fatigue or shield deformation. Maintain physical separation between transducer signal cabling and switching power circuits, especially near VFD systems, contactors, and generator excitation wiring. Metallic conduit or grounded tray routing may be used where high electromagnetic exposure exists. During field termination, ensure cable shields remain continuous through junction points without unintended chassis grounding at multiple locations. Probe extension cable lengths should remain consistent with the associated proximity transducer calibration requirements defined by the monitoring system configuration.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330104-00-05-05-01-00 3300 XL 8 mm Probe
Product Overview The Bently Nevada 330104-00-05-05-01-00 3300 XL 8 mm Probe delivers precise vibration and position monitoring in compact installations. Its 5mm design solves space limitations while maintaining full API 670 compliance. The probe features a 0.5m armored cable with M8×1 threading and a protected ClickLoc connector, ensuring secure installation and reliable signal transmission. Technical Specifications Parameter Value Model Number 330104-00-05-05-01-00 Module Type 3300 XL 8 mm Probe Manufacturer Bently Nevada Product Series 3300 Proximity Transducer System Condition Brand New Dimensions 1.8 × 1.6 × 70 cm Weight 0.08 kg HS Code 8537101190 System TSI Communication Service Ethernet Router Minimum Order Quantity 1 Origin USA Lead Time In Stock Status Active Cable Length 0.5 m Armored Thread Type M8 × 1 Connector Type Miniature Coaxial ClickLoc Certifications CSA, ATEX, IECEx, CE Functional Description The 330104-00-05-05-01-00 probe integrates seamlessly with the 3300 XL Proximitor Sensor platform. Its compact 5mm dimensions make it ideal for installations where larger probes cannot fit. Engineers benefit from SpringLoc terminals, RFI/EMI immunity, and electrical isolation built into the mounting configuration. The armored cable ensures mechanical protection, while the ClickLoc connector guarantees secure connections in harsh environments. Applications and Compatibility The 330104-00-05-05-01-00 3300 XL Probe suits industries such as power generation, petrochemical, and manufacturing. It is particularly valuable for monitoring small bearings, high-speed machinery, and equipment with limited installation space. Compatibility with the 3300 Proximity Transducer System ensures easy upgrades and reliable integration into existing monitoring setups.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330525‑02 Velomitor XA Piezo‑Velocity Sensor
Overview The 330525‑02 Velomitor XA Piezo‑Velocity Sensor is a rugged vibration‑monitoring device developed by Bently Nevada for machinery protection and condition monitoring applications. Designed for use in harsh industrial environments, this sensor provides accurate casing‑vibration measurements where shaft‑based proximity probes are not practical. Its compact, sealed construction ensures long‑term reliability in demanding process facilities. Functional Characteristics The sensor is built with a corrosion‑resistant 316L stainless steel housing and an environmentally sealed connector system, eliminating the need for external protective enclosures. The 330525‑02 meets IP65 and NEMA 4X environmental ratings, offering strong resistance to dust, moisture, and chemical exposure. Key performance features include: Piezoelectric velocity measurement for casing vibration Compact form factor for tight mounting locations Weather‑resistant cable and connector assembly Suitable for pumps, compressors, motors, and fans Designed for general industrial use (non‑radiation‑rated) This model is part of the Velomitor XA family and integrates seamlessly with Bently Nevada monitoring systems, including the 3300 series. Technical Specifications Parameter Specification Model 330525‑02 Product Type Velomitor XA Piezo‑Velocity Sensor Brand Bently Nevada Series 3300 Proximity Transducer System Dimensions 7.2 × 2.8 × 2.8 cm Weight 0.14 kg Origin USA HS Code 8537101190 Condition New Availability In Stock Housing Material 316L stainless steel Environmental Rating IP65 / NEMA 4X Application Casing vibration measurement System Compatibility TSI / Bently Nevada monitoring systems Minimum Order 1 unit Integration and System Role The 330525‑02 is used to: Measure casing vibration on rotating equipment Support predictive maintenance programs Provide input to turbine, compressor, and motor protection systems Enable continuous monitoring in harsh industrial environments Its robust mechanical design and stable output make it suitable for long‑term deployment in process industries such as petrochemical, refining, power generation, and water treatment. Application Scenarios Pumps and centrifugal compressors Industrial motors and generators Fans and blowers Machinery with limited mounting space Environments with high moisture, dust, or chemical exposure FAQ Q: What type of vibration does the sensor measure? A: It measures casing vibration using piezoelectric velocity sensing. Q: Does the sensor require a protective housing? A: No. Its stainless‑steel enclosure and sealed connector system provide full environmental protection.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330180-50-05 Proximity Sensor
Product Overview The Bently Nevada 330180-50-05 Proximity Sensor belongs to the advanced 3300 XL Proximitor Sensor system. This 5-meter extension cable ensures reliable signal transmission between probes and monitoring equipment. Its rugged design maintains signal integrity even in high-interference industrial environments. Technical Specifications Parameter Value Model Number 330180-50-05 Module Type Proximity Sensor Manufacturer Bently Nevada Product Range 3300 Proximity Transducer System Condition Brand New Dimensions 8.5 × 3.5 × 7 cm Weight 0.22 kg HS Code 8537101190 Minimum Order Quantity 1 Origin USA System TSI Communication Service Ethernet Router Status Active Functional Description The 330180-50-05 sensor features a panel-mount configuration with a 4-hole footprint identical to legacy systems. Its superior RFI/EMI immunity allows installation in fiberglass enclosures without shielded conduit, reducing installation complexity. The cable assembly incorporates SpringLoc terminal technology, eliminating screw-type connections and preventing loosening caused by vibration. Applications and Compatibility The Bently Nevada 330180-50-05 Proximity Sensor supports vibration and position monitoring in turbines, compressors, and rotating equipment. It works seamlessly with DIN-rail or traditional panel installations, offering flexibility for diverse machinery setups. CSA, ATEX, and IECEx certifications make it suitable for hazardous environments, while CE compliance ensures global acceptance. Key Benefits Compact dimensions (8.5x3.5x7cm) simplify installation in restricted spaces. Lightweight 0.22kg design improves handling and replacement efficiency. SpringLoc terminals enhance reliability by eliminating screw-type connections. Certified for hazardous locations, ensuring safe operation in demanding plants. Maintains signal integrity across 5-meter cable length in high-interference areas.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330902-00-40-10-01-05 3300 NSv Proximity Probe
Product Overview The Bently Nevada 330902-00-40-10-01-05 3300 NSv Proximity Probe belongs to the 3300 Proximity Transducer System. It delivers precise shaft vibration and position measurements in turbines, compressors, and heavy machinery. Its slim profile supports installation in space-constrained environments, while rugged construction ensures long-term reliability. Technical Specifications Parameter Value Model Number 330902-00-40-10-01-05 Module Type 3300 NSv Proximity Probe Manufacturer Bently Nevada Product Range 3300 Proximity Transducer System Condition Brand New Dimensions 62 × 62 × 1 cm Weight 0.06 kg HS Code 8537101190 Minimum Order Quantity 1 Origin USA System TSI Communication Service Ethernet Router Status Active Accuracy ±1% across operating range Operating Temperature –40 °C to +120 °C Protection Rating IP67 Connection Type SpringLoc terminal strips Certifications CE, CSA, ATEX, IECEx Immunity Enhanced RFI/EMI shielding Functional Description The 330902-00-40-10-01-05 probe incorporates advanced RFI/EMI shielding that meets CE standards, ensuring measurement accuracy in electrically noisy environments. Its IP67-rated housing protects against dust and moisture, while SpringLoc terminal strips simplify wiring without tools. The probe maintains ±1% accuracy across –40 °C to +120 °C, making it suitable for harsh industrial conditions. Applications and Compatibility The Bently Nevada 330902-00-40-10-01-05 Proximity Probe suits turbomachinery applications in power generation, oil and gas, and heavy industries. Its slim profile allows installation in high-density DIN rail or panel-mount configurations. Compatibility with the 3300 Proximity Transducer System ensures seamless integration into existing monitoring frameworks. Key Benefits Compact 62x62x1cm dimensions fit space-constrained installations. Lightweight 0.06kg design simplifies handling and replacement. IP67 housing guarantees durability in harsh industrial environments. ±1% accuracy ensures precise vibration and position monitoring. SpringLoc terminals enable secure, tool-free wiring connections.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330130-045-03-00 3300 XL 8 mm Probe
Product Overview The Bently Nevada 330130-045-03-00 3300 XL 8 mm Probe functions as a 5-meter extension cable within the 3300 XL proximity transducer system. It generates precise voltage outputs proportional to probe-to-target distances, enabling accurate measurement of static position and dynamic vibration. Its armored construction and gold-plated ClickLoc connectors ensure secure signal transmission and durability in harsh environments. Technical Specifications Parameter Value Model Number 330130-045-03-00 Module Type 3300 XL 8 mm Probe Manufacturer Bently Nevada Product Series 3300 Proximity Transducer System Condition Brand New Dimensions 27.3 × 27.3 × 3.5 cm Weight 0.46 kg HS Code 8537101190 System TSI Communication Service Ethernet Router Minimum Order Quantity 1 Origin USA Lead Time In Stock Status Active Cable Length 5 m Armored Connector Type Gold-Plated ClickLoc Operating Range -40°C to +177°C Certifications API 670, IP67 Compatibility 8 mm and 5 mm Probes Functional Description The 330130-045-03-00 maintains exceptional signal integrity across its entire length, ensuring accurate vibration and position monitoring. Its IP67 rating and patented strain relief guarantee long-term performance in demanding industrial environments. Engineers benefit from full backward compatibility with both current and legacy 3300 series components, simplifying upgrades and reducing inventory costs. Applications and Compatibility The 330130-045-03-00 3300 XL Probe suits fluid-film bearing machines, Keyphasor applications, and other critical rotating equipment. It integrates seamlessly with Bently Nevada monitoring systems, supporting predictive maintenance and centralized diagnostics. Compatibility with both 8 mm and 5 mm probes ensures flexible installation in space-constrained environments.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330180-51-05 3300 XL 5/8 mm Proximitor Sensor
Product Overview The Bently Nevada 330180-51-05 3300 XL 5/8 mm Proximitor Sensor delivers precision vibration and position monitoring for critical machinery. Designed for the 3300 Series, this sensor meets API 670 standards, ensuring mechanical stability, linear range accuracy, and reliable performance in harsh environments. Technical Specifications Parameter Value Model Number 330180-51-05 Manufacturer Bently Nevada Module Type 3300 XL 5/8 mm Proximitor Sensor Product Range 3300 Series Condition Brand New Dimensions 8.6 × 3.4 × 7 cm Weight 0.2 kg HS Code 8537101190 Minimum Order Quantity 1 Origin USA System TSI Communication Interface Ethernet Router Status Active Pull Strength 330 N (75 lbf) Compliance API 670 mechanical standards Technology TipLoc and CableLoc designs Functional Description The Bently Nevada 330180-51-05 features TipLoc molding technology, which secures probe tips to bodies for maximum durability. Its CableLoc design provides 330 N pull strength, preventing cable detachment and ensuring stable connections. With compact dimensions of 8.6 cm length and lightweight 0.2 kg construction, the sensor integrates easily into industrial systems. Engineers benefit from its ability to maintain signal integrity under vibration, temperature fluctuations, and mechanical stress. Applications and Compatibility The Bently Nevada 330180-51-05 integrates seamlessly into the 3300 XL 8 mm proximity transducer system. Manufacturers deploy this sensor in oil & gas, chemical, and heavy machinery industries where vibration monitoring and position accuracy are critical. Its plug-and-play compatibility eliminates calibration requirements, reducing downtime and ensuring consistent accuracy across system components. Key Advantages API 670 compliance guarantees mechanical stability and linear range accuracy. TipLoc technology ensures strong bonding between probe tips and sensor bodies. CableLoc design delivers 330 N pull strength for secure connections. Compact dimensions simplify installation in space-constrained environments. Full interchangeability reduces calibration needs and streamlines maintenance.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330103-05-12-10-01-00 3300 XL 8 mm Proximity Probes
Product Overview The Bently Nevada 330103-05-12-10-01-00 3300 XL 8 mm Proximity Probe belongs to the 3300 series. It provides precise vibration monitoring for turbines, compressors, and heavy industrial equipment. Its robust construction ensures reliability in harsh environments, while its compact dimensions and lightweight design simplify installation. Technical Specifications Parameter Value Model Number 330103-05-12-10-01-00 Module Type 3300 XL 8 mm Proximity Probe Manufacturer Bently Nevada Product Range 3300 Series Condition Brand New Dimensions 2 × 1.5 × 121 cm Weight 0.1 kg HS Code 8537101190 Minimum Order Quantity 1 Origin USA System TSI Communication Service Ethernet Router Status Active Dynamic Range ±10 V Output Signal 4–20 mA DC Compatibility Accelerometers, velocity transducers Firmware Field-upgradeable Design Modular, IIoT-ready Functional Description The 330103-05-12-10-01-00 probe delivers accurate displacement and vibration measurements with ±10V dynamic range and 4–20mA output. Its modular design supports integration with IIoT platforms while maintaining compatibility with legacy 3500 series installations. Facilities report faster detection of bearing faults and misalignment, improving predictive maintenance effectiveness. Applications and Compatibility The Bently Nevada 330103-05-12-10-01-00 Proximity Probe suits continuous process industries such as oil and gas, power generation, and manufacturing. Its sensitivity parameters optimize monitoring for both high-speed turbines and low-speed compressors. Operators integrate it seamlessly with control systems, gaining reliable protection against unplanned downtime. Key Benefits Compact 2x1.5x121cm dimensions simplify installation in restricted spaces. Lightweight 0.1kg design improves handling and replacement efficiency. ±10V dynamic range ensures precise vibration measurement. 4–20mA output supports integration with modern control systems. Modular design enables forward compatibility with IIoT platforms.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330980-50-05 Proximitor Sensor
Product Overview The Bently Nevada 330980-50-05 Proximitor Sensor belongs to the 3300 Proximity Transducer System. It delivers precise vibration measurements for rotating machinery in power generation, oil and gas, and heavy industry. Engineers rely on its rugged stainless steel construction and integrated electronics to ensure continuous equipment protection. Technical Specifications Parameter Value Model Number 330980-50-05 Module Type Proximitor Sensor Manufacturer Bently Nevada Product Range 3300 Proximity Transducer System Condition Brand New Dimensions 8 × 6 × 6.4 cm Weight 0.24 kg HS Code 8537101190 Minimum Order Quantity 1 Origin USA System TSI Communication Service Ethernet Router Status Active Functional Description The 330980-50-05 sensor combines advanced sensing technology with industrial-grade durability. Its wide frequency response range and excellent temperature stability guarantee consistent performance. Operators benefit from high-resolution vibration velocity measurements that enable early detection of bearing wear, imbalance, and misalignment issues. Applications and Compatibility The Bently Nevada 330980-50-05 Proximitor Sensor suits pumps, fans, and smaller turbines. Facilities integrate it into permanent installations or temporary monitoring setups. Compatibility with the 3300 Proximity Transducer System ensures seamless upgrades and simplified maintenance procedures. Key Benefits Stainless steel housing resists corrosion, moisture, and mechanical stress. Integrated electronics deliver superior signal quality and sensitivity. Compact dimensions (8x6x6.4cm) allow flexible installation in tight spaces. Lightweight 0.24kg design simplifies handling and replacement. Standardized output ensures monitor compatibility without reconfiguration.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330901-22-40-10-01-05 3300 NSv Proximity Probe
Product Overview The Bently Nevada 330901-22-40-10-01-05 NSv Proximity Probe belongs to the 3300 XL NSv Proximity Transducer System. It is engineered for vibration and position monitoring in tight-space applications where standard probes cannot fit. Its compact dimensions and lightweight build make it ideal for compressors and fluid-film bearing machines. Technical Specifications Parameter Value Model Number 330901-22-40-10-01-05 Module Type 3300 NSv Proximity Probe Manufacturer Bently Nevada Product Range 3300 Series Condition Brand New Dimensions 20.3 × 22 × 3.5 cm Weight 0.14 kg HS Code 8537101190 Minimum Order Quantity 1 Origin USA System TSI Communication Service Ethernet Router Status Active Included Components Probe, extension cable, NSv Proximitor Sensor Applications Radial vibration, thrust, tachometer, Keyphasor Functional Description The 330901-22-40-10-01-05 probe supports counter-bore, side-view, and rear-view mounting, ensuring reliable performance in restricted installation areas. It measures radial vibration and axial position on small shafts and minimal targets, providing precise monitoring where traditional 5mm or 8mm probes cannot be used. Applications and Compatibility The Bently Nevada 330901-22-40-10-01-05 NSv Proximity Probe suits centrifugal air compressors, refrigeration compressors, and process gas compressors. It integrates seamlessly with the 3300 XL NSv Proximitor Sensor and extension cables, ensuring compatibility with existing monitoring systems. Its advanced sensing capabilities enhance machinery protection and reduce downtime. Key Benefits Compact 20.3x22x3.5cm dimensions fit restricted installation environments. Lightweight 0.14kg design simplifies handling and replacement. Monitors shafts under 51mm and targets below 15mm with precision. Supports multiple mounting configurations for installation flexibility. Seamless integration with NSv probes and Proximitor Sensors.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330102-00-60-10-01-05 3300 XL 8 mm Proximity Probes
Product Overview The Bently Nevada 330102-00-60-10-01-05 3300 XL 8 mm Proximity Probe belongs to the 3300 system. It delivers precise shaft vibration and position measurements in turbines, compressors, and steam machinery. Its rugged stainless steel housing and armored cabling ensure durability in extreme industrial environments. Technical Specifications Parameter Value Model Number 330102-00-60-10-01-05 Module Type 3300 XL 8 mm Proximity Probe Manufacturer Bently Nevada Product Range 3300 System Condition Brand New Dimensions 30.5 × 33 × 4.5 cm Weight 0.3 kg HS Code 8537101190 Minimum Order Quantity 1 Origin USA System TSI Communication Service Ethernet Router Status Active Operating Temperature –40 °C to +150 °C Linearity ±1% across full measurement range Frequency Response 0–10 kHz Output Signal 4–20 mA DC Housing Material Stainless Steel Cable Protection Armored cabling Functional Description The 330102-00-60-10-01-05 probe captures both slow-roll and high-frequency vibration components with its extended frequency response. Enhanced temperature compensation ensures accuracy across extreme ranges, while ±1% linearity guarantees reliable measurements. Its modular design simplifies installation and maintenance, supporting predictive maintenance strategies in critical industries. Applications and Compatibility The Bently Nevada 330102-00-60-10-01-05 Proximity Probe integrates seamlessly with 3500 monitoring systems. It suits power generation, oil and gas, and heavy manufacturing sectors where machinery protection is essential. Operators rely on its standardized 4–20mA outputs for compatibility with modern control systems and legacy installations. Key Benefits Compact 30.5x33x4.5cm dimensions fit diverse installation environments. Lightweight 0.3kg design improves handling and replacement efficiency. Stainless steel housing resists corrosion and mechanical stress. ±1% linearity ensures precise vibration and displacement monitoring. Extended 0–10kHz frequency response captures critical vibration data.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330930-045-00-CN NSv Extension Cable
Product Overview The Bently Nevada 330930-045-00-CN NSv Extension Cable belongs to the 3300 Proximity Transducer System. It provides advanced vibration and speed measurement capabilities with exceptional reliability. Its rugged design ensures continuous operation in harsh environments, making it indispensable for critical rotating machinery. Technical Specifications Parameter Value Model Number 330930-045-00-CN Module Type NSv Extension Cable Manufacturer Bently Nevada Product Range 3300 Proximity Transducer System Condition Brand New Dimensions 20.5 × 22.5 × 3.5 cm Weight 0.55 kg HS Code 8537101190 Minimum Order Quantity 1 Origin USA System TSI Communication Service Ethernet Router Technology Digital Signal Processing (DSP) Application Range Steam turbines, compressors, large pumps Functional Description The 330930-045-00-CN cable incorporates DSP technology to deliver accurate, real-time health data. Its algorithms distinguish between normal vibrations and developing faults, enabling proactive maintenance. Seamless integration with plant control systems allows centralized monitoring without costly retrofits. Its durable construction withstands extreme temperatures, moisture, and vibration, ensuring long-term reliability. Applications and Compatibility The Bently Nevada 330930-045-00-CN NSv Extension Cable suits steam turbines, centrifugal compressors, and large pumps. It integrates with the 3300 Proximity Transducer System, supporting predictive maintenance programs. Facilities report reduced maintenance costs and improved equipment effectiveness after adopting this cable, thanks to its early warning capabilities. Key Benefits Compact 20.5x22.5x3.5cm dimensions simplify installation in restricted spaces. Moderate 0.55kg weight ensures durability without complicating handling. DSP technology enhances diagnostic accuracy and fault detection. Seamless integration reduces infrastructure upgrade costs. Proven reliability in oil and gas, power generation, and heavy manufacturing.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330106-05-30-10-02-00 3300 XL 8 mm Reverse Mount Probe
Product Overview The Bently Nevada 330106-05-30-10-02-00 3300 XL 8 mm Reverse Mount Probe provides precise eddy current measurements for both static gap and dynamic vibration monitoring. Its M10×1 threaded design and 1-meter cable length ensure secure installation, while the Miniature ClickLoc™ coaxial connector offers tool-free integration. This reverse-mount configuration allows flexible placement in space-constrained machinery setups. Technical Specifications Parameter Value Model Number 330106-05-30-10-02-00 Module Type 3300 XL 8 mm Reverse Mount Probe Manufacturer Bently Nevada Product Series 3300 Proximity Transducer System Condition Brand New Dimensions 30.5 × 33.5 × 4.5 cm Weight 0.3 kg HS Code 8537101190 System TSI Communication Service Ethernet Router Minimum Order Quantity 1 Origin USA Lead Time In Stock Status Active Cable Length 1.0 m Connector Type Miniature ClickLoc Coaxial Thread Type M10 × 1 Compliance API 670 Certifications CSA, ATEX, IECEx Pull Strength 75 lbf Functional Description The 330106-05-30-10-02-00 probe generates voltage outputs proportional to probe-to-target distances, enabling accurate Keyphasor® and speed measurements. Its TipLoc and CableLoc designs enhance durability, while backward compatibility with non-XL 5 mm and 8 mm systems simplifies upgrades. The probe complies with API 670 standards, ensuring linearity, temperature stability, and mechanical accuracy. Applications and Compatibility The 330106-05-30-10-02-00 Reverse Mount Probe suits turbines, compressors, and pumps in industries such as power generation, petrochemical, and manufacturing. It integrates seamlessly with Bently Nevada Proximitors and XL extension cables, supporting predictive maintenance and centralized diagnostics. Its reverse-mount design makes it ideal for installations in tight spaces where standard probes cannot fit.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330877-080-37-00 3300 XL 50mm Extension Cables
Product Overview The Bently Nevada 330877-080-37-00 Extension Cable belongs to the 3300 Proximity Transducer System. It provides a complete upgrade path for legacy 7200 series installations while maintaining compatibility with existing brackets. Its robust construction ensures reliable operation in demanding industrial environments. Technical Specifications Parameter Value Model Number 330877-080-37-00 Module Type 3300 XL 50mm Extension Cable Manufacturer Bently Nevada Product Range 3300 Proximity Transducer System Condition Brand New Dimensions 28 × 28 × 3 cm Weight 0.94 kg HS Code 8537101190 Minimum Order Quantity 1 Origin USA System TSI Communication Service Ethernet Router Status Active Functional Description The 330877-080-37-00 cable delivers a standardized 0.394V/mm (10mV/mil) output, ensuring seamless monitor compatibility. It supports both traditional 7200-style brackets and new adapters for 50mm DE Integral sliding mounts. Operators benefit from improved performance without reconfiguration, while the cable’s durable design guarantees long-term reliability. Applications and Compatibility The Bently Nevada 330877-080-37-00 Extension Cable integrates smoothly into turbines, compressors, and pumps. It requires full component replacement—probe, cable, and Proximitor—when upgrading legacy systems. This comprehensive approach ensures optimal performance and preserves the reliability of the 3300 XL series. Key Benefits Maintains compatibility with 7200 series brackets and adapters. Provides API-compliant design for superior machinery protection. Ensures precise vibration monitoring in critical rotating assets. Offers durable construction for high-value industrial applications.
$200.00 $100.00
You have seen 720 out of 729 products