TSI (Turbomachinery Supervisory Instrumentation) systems monitor and protect rotating equipment. We supply modules, sensors, and spares to support both new and discontinued models. Our solutions help reduce downtime and protect critical assets.
TSI Monitoring Systems
-
Yokogawa Yokogawa Temperature Monitoring Module | F3CX04-0N
Yokogawa F3CX04-0N Temperature Monitoring Module The Yokogawa F3CX04-0N, also cataloged as the F3CX04 Temperature Monitoring Module, operates as a dedicated hardware component for multi-channel temperature input processing within FA-M3 automation platforms. HardwareSpecifications Parameter Specification Model Brand Yokogawa F3CX04-0N Origin Japan Weight 200 g Dimensions 28.9 W × 100 H × 106.1 D mm OperatingTemp Max allowable ambient temperature change rate: 10 degC/h PowerConsumption 440 mA at 5 VDC NumberOfChannels 4 InputIsolation Isolated via photocouplers and transformers TerminalVoltageWithstand 150 VAC tested AlarmTypes Input upper limit alarm, input lower limit alarm (with or without delay) NumberOfAlarmOutputs 4 points per channel (only alarms 1 and 2 have relays) AlarmDelayTimer Yes WarmUpTime 30 minutes min MountingPosition Horizontal only; inverted orientation not allowed ExternalConnection 18-point terminal block with M3.5 screws InputProcessingModes Single-input (default), Two-input changeover Industrial Control Features Omron modules integrate deterministic backplane bus communication for FA-M3 systems. Firmware flash compatibility allows in-field updates without disrupting ongoing input monitoring. Channel-to-channel isolation is maintained to prevent cross-interference, supporting precise analog signal acquisition across all four inputs. Single- and two-input changeover modes allow paired or independent channel monitoring, with configurable alarm delay timers to align with system response requirements. Frequently Asked Questions Q: Can the F3CX04-0N be hot-swapped while the FA-M3 base module is powered?A: No. The module requires system power-down before insertion or removal to prevent signal disruption and relay misoperation. Q: What is the maximum rate of ambient temperature change the module can tolerate?A: The module supports up to 10 degC per hour. Faster changes may affect input accuracy and alarm triggering. Q: Are firmware updates compatible with all installed channel configurations?A: Yes, firmware flash operations preserve current input processing settings, but it is recommended to verify alarm and relay settings post-update. Field Installation Guidelines Mount the module horizontally on the FA-M3 base; inverted or vertical mounting is not permitted. Ensure 18-point terminal block connections are tightened with M3.5 screws to maintain proper electrical isolation. Route analog input wiring separately from high-current or switching circuits to minimize cross-talk. Verify ambient temperature stability; avoid locations with rapid thermal fluctuations exceeding 10 degC per hour. Ground module shielding appropriately to reduce electromagnetic interference and maintain signal integrity.
$200.00 $100.00
-
Bently Nevada Bently Nevada 144181-51 3300 XL 5/8 mm Proximity Sensor
Bently Nevada 144181-51 3300 XL 5/8 mm Proximity Sensor Configured for non-contact shaft displacement and vibration measurement in 3300 XL machinery monitoring networks, the Bently Nevada 144181-51 (144181-51 Proximity Sensor) provides direct electrical execution. The sensor assembly operates with analog voltage output scaling for rotor position and dynamic vibration acquisition across rotating equipment monitoring channels. Suffix Breakdown & Model Matrix Parameter Specification Full Model 144181-51 Base Model 144181 Brand Bently Nevada Series 3300 XL Product Type 5/8 mm Proximity Sensor Measurement Method Eddy-current non-contact sensing Output Type Analog voltage Mounting Method Threaded or bracket-mounted installation Hardware Specifications Parameter Specification Model 144181-51 Brand Bently Nevada Origin United States Series 3300 XL Sensor Type Eddy-current proximity sensor Operating Frequency 10 kHz to 1 MHz Input Impedance 50 Ohm Output Signal Analog voltage Sensitivity 200 mV/mil (7.87 V/mm) Accuracy +/-0.5% Resolution 100 mV Operating Voltage 24 VDC typical Operating Temp -40 deg C to +120 deg C Storage Temp -40 deg C to +125 deg C Humidity 0-95% non-condensing Protection Rating IP65 Housing Material Stainless steel Shaft Diameter Range 10 mm to 300 mm Probe Length 50 mm to 1000 mm Dimensions Approximately 81 x 35 x 64 mm Weight Approximately 0.25 kg to 2 kg depending on configuration Compliance CE, UL, API 670 Application Shaft displacement and vibration monitoring Eddy-Current Probe Scaling and Gap Voltage Validation The 3300 XL sensing architecture applies eddy-current transducer scaling to generate linear shaft displacement output relative to conductive target movement. Probe response is influenced by shaft metallurgy, surface finish, and radial clearance stability. During commissioning, gap voltage verification is commonly performed against nominal negative bias targets near -10 VDC to confirm proper probe-to-shaft positioning within the calibrated linear operating region. Incorrect gap positioning may introduce amplitude compression, non-linear response, or elevated cross-talk between adjacent probe channels. Rotor dynamic monitoring applications typically use the sensor for: Radial vibration measurement Axial thrust displacement detection Differential expansion observation Eccentricity and shaft position tracking The analog response bandwidth supports both slow-roll shaft behavior and higher-frequency vibration signatures generated by imbalance, rub, or misalignment conditions. Frequently Asked Questions Q: Does the 144181-51 support direct hot-swap replacement while the monitoring rack remains energized?A: Hot-swap capability depends on the associated monitoring rack and proximitor interface design. Standard practice requires verification of channel inhibit conditions before probe replacement to avoid transient vibration alarms or invalid gap readings. Q: What installation factors affect proximity sensor linearity?A: Probe tip clearance, shaft material composition, concentricity, cable routing separation, and grounding continuity directly affect linear analog response and signal stability. Q: Can multiple proximity probes be installed in close mechanical spacing?A: Yes, but probe spacing and cable shielding practices must minimize electromagnetic coupling. Cross-talk suppression becomes increasingly important in multi-channel radial vibration monitoring arrangements. Field Installation Guidelines Maintain shield grounding at a single designated instrumentation grounding point to reduce circulating noise currents. Route proximity probe extension cables separately from high-voltage motor leads and VFD output conductors. Verify probe target surface condition before calibration. Excessive shaft runout or surface scoring may distort vibration readings. Avoid excessive cable bending radius near connector transitions and probe heads. Confirm threaded engagement depth and mechanical locking torque according to the associated mounting hardware specification. Validate gap voltage after installation and again after thermal stabilization of the rotating assembly.
$200.00 $100.00
-
Bently Nevada Bently Nevada 135305-01 Dual Vibration XY/Gap Monitor
Bently Nevada 135305-01 Dual Vibration XY/Gap Monitor The Bently Nevada 135305-01, also cataloged as the 135305-01 Dual Vibration XY/Gap Monitor, operates as a dedicated hardware component for continuous radial vibration and shaft gap measurement within 3300/16 series monitoring systems. Hardware Specifications Parameter Specification Model 135305-01 Brand Bently Nevada Origin USA Weight 2.2 lbs Dimensions Standard 3300/16 module size Operating Temp –40 to +85 deg C Relative Humidity 0–95% non-condensing Power Consumption Industry-standard for 3300/16 modules Measurement Channels 2 independent channels (X and Y axes) Functions Radial vibration + shaft gap (displacement) Inputs 2 proximity probes / Proximitor sensors Frequency Response 1 Hz–4 kHz (option-dependent) Bandwidth Up to 24 kHz Sampling Rate Up to 50 kHz per channel Resolution 16-bit Outputs Programmable: 4–20 mA, 0 to –10 Vdc, +1 to +5 Vdc Recorder Outputs Dedicated, short-circuit protected Hot-Swap Compatible within 3300 series racks Compliance API 670, CSA, ATEX, CE Eddy-Current Probe Scaling & Rotor Dynamics The 135305-01 module implements precise eddy-current probe scaling to ensure accurate radial vibration and shaft gap measurements. Gap voltage validation is maintained at –10 VDC targets for all Proximitor channels. Rotor dynamics signals are captured with 16-bit resolution, and cross-talk suppression is applied to prevent interference between X and Y channels. Programmable low-frequency filtering allows monitoring of slow-speed machinery without loss of diagnostic fidelity. Frequently Asked Questions (FAQ) Q: Can this module be hot-swapped without shutting down the 3300/16 rack?A: Yes, the 135305-01 supports controlled hot-swap within 3300 series racks, maintaining all channel calibration and alarm settings. Q: What is the maximum sampling rate per channel?A: Each channel can sample up to 50 kHz, supporting high-speed vibration monitoring. Q: Does the module support independent gap alarm thresholds?A: Yes, separate ALERT and DANGER setpoints can be configured for both vibration and displacement channels. Field Installation Guidelines Install module in a 3300/16 rack with correct slot orientation; ensure proper mechanical retention. Connect Proximitor probes with shielded cabling; terminate shields to system ground. Maintain separation between sensor cabling and high-current or high-voltage lines to reduce EMI. Verify probe excitation voltage and cable continuity before system power-up. Use manufacturer-recommended torque for all terminal connections. Ensure ambient conditions comply with –40 to +85 deg C operating range and 0–95% relative humidity.
$200.00 $100.00
-
Bently Nevada Bently Nevada 133811-02 3500/61 Temperature Monitor Module
Bently Nevada 133811-02 3500/61 Temperature Monitor Module The Bently Nevada 133811-02 serves as the primary 133811-02 3500/61 Temperature Monitor Module utilized to execute high-accuracy temperature signal monitoring across Bently Nevada 3500 Machinery Protection System platforms. Suffix Breakdown & Model Matrix The 133811-02 is supplied as a single fixed-configuration module. No additional suffixes or alternative model matrices are specified in the provided documentation. The module supports six independent temperature input channels and integrates with 3500 Series rack systems for signal processing and alarm output. Hardware Specifications Parameter Specification Model 133811-02 Brand Bently Nevada Origin USA Weight 0.91 kg Dimensions 241.3 × 24.4 × 241.8 mm Operating Temp −30 deg C to +65 deg C Storage Temp −40 deg C to +85 deg C Power Consumption ~5.8 W Input Channels 6 temperature channels Supported Sensors RTDs (2/3/4-wire), Thermocouples (Type J, K, T, E), Thermistors Measurement Range Sensor-dependent (e.g., −200 deg C to +850 deg C for thermocouples) Accuracy ±3 deg C at 25 deg C typical, ±0.1% FS Resolution 16-bit A/D Analog Outputs 2 outputs, 4–20 mA Alarm Functions Independent Alert and Danger thresholds per channel Relay Output Via 3500 rack relay modules Certifications CE, CSA, ATEX, IECEx Rotor Thermal & Signal Integrity Features The module incorporates cross-channel signal isolation to prevent interference between analog temperature inputs. Thermocouple inputs include cold junction compensation (CJC) to maintain accuracy over the operating range. Input scaling is performed internally to ensure consistent readings across 2/3/4-wire RTDs and multiple thermocouple types. The module design mitigates electromagnetic interference from adjacent machinery and rack components, maintaining integrity of real-time monitoring data critical to predictive maintenance. Frequently Asked Questions (FAQ) Q: Can the 133811-02 module be hot-swapped without disrupting the rack?A: Yes. The module supports hot-swap replacement, allowing maintenance without powering down the 3500 Series rack. Q: How are temperature inputs isolated from each other?A: Each input channel is galvanically isolated, reducing cross-talk and preventing interference between sensors. Q: What is the recommended ambient environment for accurate operation?A: Operate within −30 deg C to +65 deg C, with humidity up to 95% non-condensing. Avoid direct exposure to water ingress or strong EMI sources beyond standard industrial control environments. Field Installation Guidelines Install modules in 3500 Series racks according to rack orientation and slot numbering. Ensure proper backplane engagement; listen for tactile click confirming seating. Route sensor cables to minimize exposure to high-voltage lines or switching noise. Maintain grounding and shield continuity on thermocouple or RTD cabling for optimal signal fidelity. Avoid mechanical shock or bending stress on input cables; secure wiring with cable ties or trays.
$200.00 $100.00
-
Bently Nevada Bently Nevada 129974-01 Industrial Monitoring I/O Module
Bently Nevada 129974-01 Industrial Monitoring I/O Module The Bently Nevada 129974-01 serves as the primary 129974-01 Industrial Monitoring I/O Module utilized to execute transducer signal acquisition and vibration diagnostic communication across machinery protection system platforms. Hardware Specifications Parameter Specification Model 129974-01 Brand Bently Nevada Origin United States Weight Not specified Dimensions 150 x 100 x 50 mm Operating Temp -40 to +85 deg C Storage Temp -55 to +105 deg C Power Consumption Not specified Power Supply 24 VDC Input Channels 8 channels Output Channels 4 channels Communication Interfaces Ethernet, RS-485 Signal Range +/-10 Vpp or 4-20 mA Transducer Power -24 VDC regulated, up to 40 mA Frequency Response 4 Hz to 4 kHz vibration; 0.017 Hz to 20 kHz speed Enclosure Rating IP65 Certifications CE, RoHS Supported Sensors Proximity probes, accelerometers, Velomitor transducers Eddy-Current Probe Scaling and Rotor Dynamics The module supports eddy-current probe scaling for shaft vibration and position measurements associated with rotor dynamics analysis. Integrated signal conditioning filters high-frequency interference before transmission to supervisory systems through Ethernet or RS-485 links. Gap voltage validation aligned with -10 VDC probe targets assists in maintaining stable transducer bias conditions during continuous monitoring. Cross-talk suppression between adjacent channels reduces interference during simultaneous multi-sensor acquisition. Frequently Asked Questions (FAQ) Q: Does the 129974-01 support both voltage and current input signals?A: Yes. The module accepts signal ranges of +/-10 Vpp and 4-20 mA depending on sensor configuration. Q: Can the module supply power directly to connected transducers?A: Yes. It provides regulated -24 VDC transducer power with output current up to 40 mA. Q: Are redundant monitoring configurations supported?A: Yes. The module documentation specifies support for redundant configurations intended for machinery protection architectures. Field Installation Guidelines Install the module inside grounded industrial control enclosures with adequate airflow clearance. Route proximity probe and accelerometer cabling separately from motor power conductors. Terminate cable shields at the designated ground reference point to reduce induced electrical noise. Verify transducer polarity and communication addressing before energizing the module. Maintain dry enclosure conditions consistent with the specified IP65 environmental protection level.
$200.00 $100.00
-
Bently Nevada Bently Nevada 124534-01 Proximitor Transducer Module
Bently Nevada 124534-01 Proximitor Transducer Module Configured for shaft vibration and gap position monitoring in Bently Nevada TSI systems, the Bently Nevada 124534-01 (124534 Proximitor Transducer Module) provides direct electrical conversion of eddy-current probe impedance variation into a proportional negative DC output signal for rotor dynamic measurement circuits. Hardware Specifications Parameter Specification Model 124534-01 Brand Bently Nevada Origin United States Product Type Proximitor Transducer Module Supply Voltage -24 VDC Linear Sensitivity 200 mV/mil Sensitivity Equivalent Approximately 7.87 V/mm Measurement Range 10-90 mils (0.25-2.30 mm) Output Signal Negative DC voltage proportional to probe gap Connector Type 3-pin Housing Material Aluminum Mounting Method DIN rail mounting Weight 0.75 lbs Compatibility Bently Nevada 3300 and 3500 monitoring systems Calibration Reference -10 VDC at 50 mil gap target Signal Interface Eddy-current proximity probe input Eddy-Current Probe Scaling and Gap Voltage Validation The module operates as a calibrated Proximitor interface for eddy-current probe assemblies. Linear scaling is maintained at 200 mV/mil throughout the specified operating span between 10 mils and 90 mils. Gap voltage verification is typically referenced at approximately -10 VDC during probe alignment at the 50 mil mechanical center position. Incorrect target gap adjustment may introduce amplitude deviation in radial vibration channels and axial position measurements. Internal circuit construction incorporates shielding methods intended to reduce EMI and probe cable cross-talk effects in turbine supervisory instrumentation installations where parallel routing of transducer cables exists. Frequently Asked Questions Q: Does the 124534-01 support hot replacement during system operation?A: The supplied documentation does not specify online hot-swap capability. Standard industrial practice is to isolate monitor channel power before transducer replacement to prevent incorrect gap reference readings. Q: What type of output does the module generate?A: The module provides a negative DC voltage output proportional to probe-to-target distance variation derived from eddy-current signal conditioning circuitry. Q: What installation factor most directly affects measurement accuracy?A: Probe gapping accuracy and shield grounding continuity directly influence linear response stability and vibration signal integrity. Improper shield termination may increase electrical noise coupling. Field Installation Guidelines Install the module on grounded DIN rail structures with low impedance bonding continuity. Maintain physical separation between transducer cabling and high-voltage motor conductors. Use shielded extension cable assemblies approved for matching eddy-current probe systems. Avoid sharp cable bending near probe connectors to minimize impedance variation. Confirm target material compatibility before calibration procedures. Validate gap voltage prior to machine startup and after rotor maintenance activity. Terminate cable shielding at the designated instrumentation ground point only to reduce ground-loop current circulation.
$200.00 $100.00
-
Bently Nevada Bently Nevada 102550-01 Monitor Main Module
Bently Nevada 102550-01 Monitor Main Module The Bently Nevada 102550-01, also cataloged as the 102550 Monitor Main Module, operates as a dedicated hardware component for PLC I/O signal handling and machinery monitoring interface execution within Bently Nevada monitoring and automation systems. The module links field transducers and controller logic through continuous online signal acquisition and process communication functions. Hardware Specifications Parameter Specification Model 102550-01 Brand Bently Nevada Origin United States Product Type PLC I/O Modules Module Type Monitor Main Module Compatibility Bently Nevada systems and compatible PLC platforms Monitoring Capability Continuous online machinery monitoring Construction Industrial-grade module assembly Integration Method PLC and monitoring system interface connection Dimensions 190 x 16.2 x 10.8 cm Weight 1.2 kg Supported Functions Signal acquisition, monitoring interface, machinery protection support Cross-Talk Suppression and Signal Conditioning The module architecture supports conditioned signal transfer between machinery transducers and PLC interface circuitry. Internal signal routing is arranged to reduce electrical cross-talk between adjacent monitoring channels and control-related signal paths. When integrated with eddy-current proximity probe systems, signal stability depends on matched transducer scaling and controlled grounding continuity. Probe circuits operating near standard -10 VDC gap reference targets require shield integrity throughout the cable path to maintain stable shaft position measurements. Channel isolation practices within the monitoring assembly assist in minimizing transient interference generated by relay switching devices, variable-frequency drives, and adjacent power conductors. Frequently Asked Questions Q: Does the 102550-01 support online module replacement during operation?A: Replacement procedures depend on the host monitoring platform and PLC architecture. Power isolation and communication verification should be completed before module removal. Q: Can the module interface directly with standard PLC input structures?A: The module is designed for integration with compatible PLC systems and Bently Nevada monitoring platforms using supported signal interface methods. Q: What installation condition most affects signal integrity?A: Improper shield grounding, parallel routing with power conductors, and loose connector termination can introduce electrical noise into low-level monitoring signals. Field Installation Guidelines Install the module within a grounded industrial enclosure with adequate spacing for cable routing and heat dissipation. Secure all field wiring to prevent connector stress caused by vibration or cabinet movement. Separate low-level transducer wiring from motor power cables, relay outputs, and switching power supplies. Maintain continuous shield grounding according to the site instrumentation standard. Inspect terminal connections periodically for oxidation, loosened hardware, or insulation degradation. Avoid excessive cable bending near module connector interfaces during maintenance procedures.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/05-02-04-01-00-01 System Rack
Bently Nevada 3500/05-02-04-01-00-01 System Rack The Bently Nevada 3500/05-02-04-01-00-01 serves as the primary 3500/05 System Rack utilized to execute module power distribution and backplane signal routing across 3500 Machinery Protection System platforms. The rack frame supports monitor module installation, redundant power supply integration, and internal communication paths between vibration, relay, and interface modules. Suffix Breakdown & Model Matrix The supplied documentation identifies the model as a fixed rack assembly configuration. No official suffix allocation matrix or option decoding structure was provided within the source material. Hardware Specifications Parameter Specification Model 3500/05-02-04-01-00-01 Brand Bently Nevada Origin United States Product Type Machinery Protection System Racks Rack Size Full-size 19-inch EIA rack Slot Capacity 14 slots Dimensions 19-inch rack format Weight Not specified Mounting Options Panel mount, rack mount, bulkhead mount Operating Temp -20 deg C to +65 deg C Storage Temp -40 deg C to +85 deg C Power Consumption Dependent on installed module count and power supply configuration Power Supply Support Dual redundant power supplies Hazardous Area Rating ATEX/IECEx Zone 2, CSA Class I Division 2 Compliance FCC Part 15, EMC Directive 2014/30/EU, RoHS Directive 2011/65/EU Certifications ABS, DNV GL, CE, CSA, IECEx Rotor Dynamics Signal Path Integrity The rack backplane architecture maintains dedicated communication paths between machinery monitoring modules used for rotor vibration and axial position analysis. Internal signal routing is arranged to reduce electrical interference between adjacent monitor channels and relay outputs. When used with eddy-current probe monitoring systems, the rack supports stable module communication required for probe scaling and gap voltage verification. Typical proximity transducer systems operating near -10 VDC gap targets depend on shield continuity and controlled grounding practices across rack wiring assemblies. Frequently Asked Questions Q: Does the rack permit online replacement of monitoring modules?A: Replacement procedures depend on the installed module type and site maintenance policy. Backplane communication status and redundant power condition should be verified before module extraction. Q: Can the rack operate with a single installed power supply?A: Yes. The rack can operate with one power supply installed. Redundant operation requires installation of dual compatible power supply modules. Q: Are all rack mounting formats interchangeable between full-size and mini-rack versions?A: No. Mini-rack versions are not available with bulkhead mounting configurations. Mechanical mounting compatibility depends on rack frame size.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/05-02-04-01-00-00 System Rack
Bently Nevada 3500/05-02-04-01-00-00 System Rack Configured for module power distribution and backplane communication in the 3500 Machinery Protection System, the Bently Nevada 3500/05-02-04-01-00-00 (3500/05 System Rack) provides direct physical and electrical execution. The rack assembly supports monitoring module installation, redundant power input routing, and internal signal transfer between vibration, relay, and communication modules within the 3500 platform. Hardware Specifications Parameter Specification Model 3500/05-02-04-01-00-00 Brand Bently Nevada Origin United States Product Type Machinery Protection System Rack Rack Format Full-size 19-inch EIA rack Slot Capacity 14 slots Mounting Options Panel mount, rack mount Weight 4.5 kg Operating Temp -20 deg C to +65 deg C Storage Temp -40 deg C to +85 deg C Power Consumption Dependent on installed module population and power supply configuration Power Supply Support Dual redundant power supplies Backplane Function Internal module communication and power distribution Compliance FCC Part 15, EMC Directive 2014/30/EU, LV Directive 2014/35/EU, RoHS Directive 2011/65/EU Hazardous Area Approvals ATEX/IECEx Zone 2, CSA Class I Division 2 Certifications ABS, DNV GL, CE, CSA, IECEx, GOST Eddy-Current Probe Signal Distribution and Cross-Talk Isolation The 3500/05 rack backplane architecture is designed to maintain signal separation between adjacent machinery monitoring modules operating with eddy-current probe inputs. Shield continuity and low-noise grounding paths are used to minimize cross-talk between high-sensitivity vibration channels and relay output circuits. Within 3500 monitoring systems, probe extension cable scaling and gap voltage validation are processed by installed monitor modules while the rack distributes regulated power and communication pathways. Typical proximity probe systems targeting -10 VDC gap reference values depend on stable rack grounding continuity and controlled shield termination practices. Frequently Asked Questions Q: Does the 3500/05 rack support hot-swapping of monitoring modules?A: Module insertion and removal capability depends on the installed monitor type and plant maintenance procedures. Power isolation verification and rack communication status checks should be completed before module replacement. Q: Can redundant power supplies operate simultaneously in the rack?A: Yes. The rack supports dual redundant power supplies configured for automatic transfer during loss of the primary supply input. Q: Are mini-rack and full-size rack mounting methods interchangeable?A: No. Bulkhead mounting is not available for mini-rack versions. Mounting compatibility depends on the selected rack format and frame dimensions.
$200.00 $100.00
-
Bently Nevada 3500/05-01-01-00-00 Bently Nevada System Rack Chassis
Bently Nevada 3500/05-01-01-00-00 System Rack The Bently Nevada 3500/05-01-01-00-00, also cataloged as the 3500/05 system rack, operates as a dedicated hardware chassis for mechanical protection module hosting within the 3500 Machinery Protection System. Configured for structured module accommodation and backplane distribution in the 3500 rack architecture, the Bently Nevada 3500/05-01-01-00-00 (3500/05 rack) provides direct electrical interconnection and physical mounting for monitoring, relay, and communication modules. Suffix Breakdown & Model Matrix 01 → Full-size 19-inch rack configuration 01 → Rear-access wiring architecture 00-00-00 → Standard mechanical and enclosure configuration Hardware Specifications ParameterSpecification Model 3500/05-01-01-00-00 Brand Bently Nevada Origin Not specified Weight 4.5 kg Dimensions Height ~266 mm; Width 483 mm; Depth 267–349 mm Operating Temp -20 deg C to +65 deg C Power Consumption Not specified (backplane distributed, module-dependent) Rack Type 19-inch EIA full-size chassis Slot Capacity 14 slots Mounting Panel mount / rack mount Wiring Access Rear-access Protection Class IP20 Eddy-Current Probe Scaling and Backplane Signal Integrity (TSI Architecture) The 3500/05 rack backplane maintains controlled distribution paths for vibration and position measurement chains used in eddy-current probe systems. Probe scaling alignment is preserved through module-to-backplane impedance consistency, ensuring stable conversion of gap voltage signals typically referenced against -10 VDC linear range targets. Signal routing is structured to reduce cross-talk between adjacent monitoring channels, maintaining separation between vibration, Keyphasor, and relay bus lines. Rotor dynamics data acquisition integrity depends on stable backplane reference grounding and deterministic slot addressing across installed 3500 modules. Frequently Asked Questions (FAQ) Q: Does the 3500/05-01-01-00-00 support hot-swapping of installed modules? A: Yes. The backplane architecture supports module hot-swap while maintaining rack-level power and communication continuity. Individual module replacement does not require full rack power removal. Q: How is backplane power distributed across the 14-slot architecture? A: Power is distributed through a centralized backplane rail system. Load is determined by installed modules, including monitor, relay, and communication cards. Redundant power supply configurations are supported via dedicated supply slots. Q: Can rear-access wiring be combined with panel mounting in the same configuration? A: No mixed configuration is defined within a single rack option code. The 01 wiring option specifies rear-access only, while mounting style is selected independently at cabinet integration level. Field Installation Guidelines Maintain minimum rear clearance for wiring harness routing under rear-access configuration Ensure chassis grounding to cabinet earth using low-impedance bonding strap Install power supply modules before inserting monitoring or communication cards Avoid routing high-voltage cabinet wiring parallel to backplane signal harness paths Verify slot alignment before inserting modules to prevent backplane connector damage Maintain ventilation spacing in accordance with cabinet thermal design limits
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/05-01-03-00-00-00 19-Inch System Rack Chassis
Product Description The Bently Nevada 3500/05-01-03-00-00-00 is a full-width 19-inch industrial rack chassis developed for the 3500 Machinery Protection System. It functions as the mechanical and electrical backbone for all system modules, providing structured housing, integrated power distribution, and internal communication routing across the platform. This chassis is designed to accommodate monitoring modules, relay cards, communication interfaces, Keyphasor modules, and power supply units within a unified rack architecture. It supports continuous-duty operation in industrial environments where system stability and modular scalability are required. The configuration code “01-03-00-00-00” defines a standard full-size rack design with factory default mechanical and backplane layout. Core System Functions Mechanical housing for complete 3500 module architecture Integrated backplane for power and signal distribution Centralized communication routing between modules Support for monitoring, relay, and communication cards Hot-swappable module insertion capability Compatible with redundant power supply configurations Flexible installation in industrial cabinet systems Designed for continuous machinery protection operation Technical Specifications ParameterSpecification Model 3500/05-01-03-00-00-00 Product Type 19-Inch System Rack Chassis System Series Bently Nevada 3500 Rack Standard 19-inch EIA industrial format Total Module Capacity 14 slots Backplane Function Power distribution + system communication bus Power Supply Support 3500/15 AC or DC modules Redundancy Support Available Hot-Swap Capability Supported Supported Modules Monitoring, relay, communication, Keyphasor Slot Architecture Dedicated slot for power supply module Dedicated slot for Rack Interface Module (RIM) 14 configurable module positions for system expansion Mixed module compatibility across all 3500 series components Mechanical Specifications ItemSpecification Width 483 mm (19-inch EIA standard) Height Approx. 266 mm Depth 267–349 mm (varies by mounting configuration) Weight 4.5 kg Material Industrial-grade aluminum alloy Mounting Types Panel mount / Rack mount / Bulkhead mount Electrical Architecture Internal backplane distributes regulated power to all installed modules Supports AC and DC power input via 3500/15 power supplies Dual redundant power supply compatibility Integrated system communication bus for inter-module data exchange Designed for continuous operational stability in protection systems Environmental Ratings ParameterValue Operating Temperature -20°C to +65°C Storage Temperature -52°C to +105°C Humidity 10–90% RH non-condensing Vibration Resistance 5–150 Hz, 2G Shock Resistance 15G, 11 ms Protection Class IP20 Compliance & Certifications EMC: EN 61000-6-2 / EN 61000-6-4 Safety: EN 61010-1 RoHS: 2011/65/EU Hazardous Area Approvals: ATEX / IECEx / CSA / NRTL (Zone 2 rated configurations) Marine Certifications: ABS / DNV-GL compliant designs Key Features Full-size 14-slot chassis architecture for system expansion Compatible with complete 3500 module portfolio Hot-swappable design for maintenance without shutdown Rugged industrial-grade construction Suitable for harsh environmental conditions Supports flexible wiring access (front or rear depending on mounting style) Designed for mission-critical machinery protection infrastructure Application Areas Gas and steam turbine protection systems Compressor station monitoring platforms Oil and gas production facilities Power generation control systems Pipeline pumping infrastructure Offshore and marine machinery protection systems Industrial rotating equipment monitoring networks FAQ How many modules can be installed in this rack? The chassis provides 14 standard module slots, in addition to dedicated positions for power and interface modules. Does it support redundant power configuration? Yes. The rack is designed to support single or dual redundant power supply arrangements. Can modules be replaced while the system is running? Yes. The system supports hot-swappable module replacement for maintenance without full shutdown.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/05-01-03-00-00-01 19-Inch System Rack Chassis
Product Description The Bently Nevada 3500/05-01-03-00-00-01 is a full-width 19-inch rack chassis engineered as the structural backbone of the 3500 Machinery Protection System. It provides the physical housing, electrical backplane distribution, and communication interconnection required for all monitoring, protection, and interface modules in the 3500 platform. This rack serves as the central mounting platform for power supplies, monitoring modules, relay modules, communication gateways, and system interface components. It is designed for continuous operation in industrial environments requiring high reliability, modular expansion, and hot-swappable maintenance capability. The configuration code “01-03-00-00-01” identifies a standard 19-inch chassis variant with factory-defined mechanical and backplane layout. Core System Functions Structural mounting platform for 3500 system modules Integrated backplane for power and data distribution Centralized communication bus architecture Support for monitoring, relay, and communication modules Hot-swappable module insertion and removal Compatibility with redundant power supply configurations Integration into industrial control cabinet systems Designed for continuous-duty machinery protection systems Technical Specifications ParameterSpecification Model 3500/05-01-03-00-00-01 Product Type 19-Inch System Rack Chassis System Platform Bently Nevada 3500 Series Rack Standard 19-inch EIA industrial chassis Slot Capacity 14 module slots Backplane Type Integrated system communication + power bus Mounting Options Panel mount / Rack mount / Bulkhead mount Power Supply Support 3500/15 AC or DC modules Redundant Power Support Supported Module Hot Swap Supported Slot Architecture Dedicated power supply slot(s) Rack Interface Module (RIM) slot 14 total module positions for system expansion Support for mixed module configuration (monitoring, relay, communication) Mechanical Specifications ItemSpecification Width 483 mm (19-inch standard) Height Approx. 266 mm Depth 267–349 mm (varies by mounting style) Weight 4.5 kg Construction Material Industrial-grade aluminum alloy Installation Orientation Horizontal rack cabinet mounting Electrical System Characteristics Backplane distributes regulated power to all installed modules Compatible with AC and DC power supply modules Supports dual-redundant power configuration Integrated system-level communication bus via backplane Continuous operation design for mission-critical monitoring systems Environmental Ratings ParameterValue Operating Temperature -20°C to +65°C Storage Temperature -52°C to +105°C Humidity 10–90% RH, non-condensing Vibration Resistance 5–150 Hz, 2G Shock Resistance 15G, 11 ms Protection Rating IP20 enclosure standard Installation & Integration Notes The 3500/05-01-03-00-00-01 rack is designed for installation in industrial control cabinets and can be configured for: Front-access wiring (bulkhead installations) Rear-access maintenance configurations Standard rack-mounted enclosure systems It provides full compatibility with the complete Bently Nevada 3500 module ecosystem. Application Areas Turbomachinery protection systems Oil and gas compressor monitoring systems Power generation control cabinets Pipeline pumping station installations Industrial rotating equipment monitoring Offshore and marine machinery protection systems SCADA-integrated monitoring infrastructures FAQ What is the main purpose of the 3500/05 rack system? It serves as the central chassis that mechanically supports and electrically connects all modules within the Bently Nevada 3500 machinery protection platform. How many modules can it hold? The rack provides 14 standard module slots, excluding dedicated positions for power supplies and the rack interface module. Does it support redundancy? Yes, the system supports redundant power supply configurations for increased reliability.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/92-02-01-00 Modbus RTU RS485 Gateway Module
Product Description The Bently Nevada 3500/92-02-01-00 is a serial communication interface module designed for the 3500 Machinery Protection System. It establishes a reliable data pathway between the 3500 monitoring rack and external control environments such as DCS, SCADA, PLC systems, and plant-level data historians. The module converts internal rack diagnostic and protection data into Modbus RTU format for transmission over RS-485 networks, enabling integration with widely deployed industrial serial communication infrastructures where Ethernet connectivity is not required or available. The configuration code “02-01-00” defines the hardware and firmware setup: 02: RS-485 Modbus serial interface 01: Low memory configuration 00: Standard firmware package without extended options The module installs into a standard 3500 rack architecture requiring one front slot and one rear I/O slot. Core Communication Functions Real-time Modbus RTU data communication over RS-485 Continuous acquisition of rack and channel-level measurements Transmission of alarm and diagnostic status to external systems Support for multi-drop serial network architectures Structured access to 3500 system registers Integration with PLC, DCS, and SCADA platforms Event and fault data reporting for condition monitoring systems Technical Specifications ParameterSpecification Model 3500/92-02-01-00 Product Type Modbus RTU Communication Gateway Module Communication Interface RS-485 (EIA-485 standard) Protocol Modbus RTU Memory Configuration Low memory architecture Transmission Mode Multi-drop serial communication Baud Rate Range 1,200 to 115,200 bps Data Format 8 data bits, configurable parity, 1 stop bit Maximum Cable Distance Up to 1,200 meters (dependent on baud rate) Power Consumption 7.0 W typical Power Supply 3500 rack backplane Data Handling Capabilities System Data Output Vibration and process measurement values Speed and dynamic machine parameters Rack, module, and channel status indicators Alarm states (Alert / Danger conditions) Configuration and setpoint data Diagnostic and event logs Supported Modbus Functions Read Holding Registers Read Input Registers Read Coil Status (limited support) Read Discrete Inputs Physical Specifications ItemSpecification Dimensions 241.3 × 24.4 × 241.8 mm Weight 0.79 kg Installation Requirement 1 front slot + 1 rear I/O slot Module Format Full-height rack-mounted design Environmental Ratings ParameterValue Operating Temperature -30°C to +65°C Storage Temperature -40°C to +85°C Relative Humidity Up to 95% non-condensing EMC Compliance EN 61000-6-2 / EN 61000-6-4 Safety Standard EN 61010-1 Key Features RS-485 based Modbus RTU communication interface Designed for long-distance industrial serial networks Low memory configuration optimized for standard data handling Stable integration with legacy control systems Multi-drop network capability for distributed architectures Full rack data accessibility through Modbus registers Hot-swappable module design for maintenance flexibility Industrial-grade electrical and environmental robustness Application Scenarios Turbomachinery monitoring and protection systems Oil and gas compressor station control networks Power generation equipment monitoring Pipeline and distribution system supervision PLC-based plant automation systems SCADA and DCS serial communication integration Industrial condition monitoring infrastructure FAQ What communication protocol does this module use? It operates using Modbus RTU over RS-485 serial communication. Is this module suitable for long-distance communication? Yes. RS-485 architecture supports communication distances up to approximately 1,200 meters depending on baud rate and installation conditions. What does the “low memory” configuration mean? It refers to a simplified firmware profile designed for standard register-based communication without extended memory mapping features.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/91-01-02-02 Dual Fiber EGD Gateway Module
Overview The Bently Nevada 3500/91-01-02-02 is a dual-port fiber Ethernet communication gateway designed for the 3500 Machinery Protection System. It provides deterministic Ethernet Global Data (EGD) connectivity between the 3500 monitoring rack and external control platforms including GE Mark VI/VIe turbine controllers, DCS, and SCADA systems. This module is engineered for high-integrity, real-time data transfer in redundant or dual-network architectures. It enables continuous transmission of machine protection data, including vibration measurements, process variables, alarm conditions, and system diagnostics, over industrial fiber-optic networks. The unit is installed in one front slot and one rear I/O slot within the 3500 rack assembly. Core Functions High-speed Ethernet Global Data (EGD) communication interface Dual independent fiber-optic network channels Real-time transmission of rack and channel data Continuous alarm and diagnostic reporting Support for redundant communication architectures Integration with GE Mark VI/VIe control systems Remote command and system control capability Hot-swappable rack module design Technical Specifications ParameterSpecification Model 3500/91-01-02-02 Product Type EGD Communication Gateway Module System Platform Bently Nevada 3500 Series Communication Protocol EGD v2.01 Transport Layer UDP/IP Ethernet Standard IEEE 802.3u Network Interface Dual 100BASE-FX fiber ports Connector Type MT-RJ Fiber Type Multimode fiber (typical installation) Communication Mode Redundant / dual-network support Power Consumption 7.4 W typical Power Source 3500 rack backplane Data Communication Capabilities Producer Data (Outbound from Rack) Vibration and dynamic channel values Speed and process variables Rack and module status information Alarm and setpoint data System health diagnostics Consumer Commands (Inbound Control Signals) Group Reset Alarm Inhibit functions Trip Multiply activation Special Alarm Inhibit control Physical Specifications ItemSpecification Dimensions 241.3 × 24.4 × 241.8 mm Weight 0.79 kg Installation Requirement 1 front slot + 1 rear I/O slot Module Format Full-height rack-mounted module Environmental Specifications ParameterValue Operating Temperature -30°C to +65°C Storage Temperature -40°C to +85°C Humidity Up to 95% non-condensing EMC Compliance EN 61000-6-2 / EN 61000-6-4 Safety Standard EN 61010-1 Key Features Dual fiber-optic Ethernet channels for redundancy 100BASE-FX multimode fiber communication support Deterministic real-time EGD data exchange High immunity to electromagnetic interference Designed for mission-critical turbine and compressor systems Seamless integration with GE control platforms Industrial-grade environmental robustness Hot-swappable maintenance design Application Areas Gas turbine control and monitoring systems Steam turbine protection architectures Compressor station monitoring systems Oil and gas production facilities Pipeline and pumping infrastructure Power generation plants Offshore and marine rotating equipment systems SCADA and distributed control integration FAQ What is the benefit of dual fiber ports in this module? The dual-port design supports redundant network paths or dual communication channels, improving system reliability and fault tolerance. Can this module operate in redundant Ethernet architectures? Yes. The 3500/91-01-02-02 is specifically suited for redundant or dual-network EGD configurations. What type of fiber is supported? The module typically operates with multimode fiber using 100BASE-FX standards and MT-RJ connectors.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/91-01-02-00 Fiber EGD Gateway Module
Overview The Bently Nevada 3500/91-01-02-00 is a fiber-optic Ethernet Global Data (EGD) communication gateway designed for integration within the 3500 Machinery Protection System. This module provides a high-reliability digital interface between the 3500 rack and external automation platforms such as GE Mark VI/VIe turbine control systems, DCS, and SCADA networks. This configuration is engineered for extended-distance communication using fiber-optic media, improving immunity to electromagnetic interference in harsh industrial environments. It enables continuous exchange of machinery protection data, alarm states, and system diagnostics in real time. The module occupies one front slot and one rear I/O slot within the 3500 rack architecture. Core Functions Real-time Ethernet Global Data (EGD) communication Fiber-optic industrial Ethernet data transmission Continuous monitoring of rack and module status Transfer of alarm, setpoint, and channel measurement data Integration with GE turbine control platforms Support for remote reset and alarm control commands High electromagnetic noise immunity for harsh environments Hot-swappable rack module design Technical Specifications ParameterSpecification Model 3500/91-01-02-00 Product Type EGD Communication Gateway Module System Platform Bently Nevada 3500 Series Communication Protocol Ethernet Global Data (EGD) v2.01 Transport Layer UDP/IP Ethernet Standard IEEE 802.3u Network Medium Fiber optic (100BASE-FX) Connector Type MT-RJ fiber interface Data Transmission Type Real-time producer/consumer model Power Consumption 7.4 W typical Power Source 3500 rack backplane Data Communication Structure Producer Data Channel measurement values Rack and module status signals Alarm and warning states System health diagnostics Configuration and setpoint data Consumer Commands Group Reset Alarm Inhibit functions Trip Multiply control Special Alarm Inhibit commands Physical Characteristics ItemSpecification Dimensions 241.3 × 24.4 × 241.8 mm Weight 0.79 kg Installation Requirement 1 front slot + 1 rear I/O slot Form Factor Full-height 3500 rack module Environmental Specifications ParameterValue Operating Temperature -30°C to +65°C Storage Temperature -40°C to +85°C Relative Humidity Up to 95% non-condensing EMC Compliance EN 61000-6-2 / EN 61000-6-4 Key Features Fiber-optic 100BASE-FX Ethernet communication interface Extended-distance transmission capability High immunity to electrical noise and interference Real-time EGD data exchange architecture Hot-swappable design for maintenance flexibility Compatible with GE Mark VI/VIe control systems Reliable industrial-grade communication performance Application Areas Gas turbine control and monitoring systems Steam turbine protection platforms Compressor station monitoring Offshore oil and gas machinery systems Pipeline pumping and transport systems Power generation plant integration Industrial SCADA and DCS communication networks FAQ What is the advantage of the fiber-optic version of the 3500/91? The fiber-optic interface provides improved signal integrity and allows long-distance communication with strong resistance to electromagnetic interference. Can this module work with GE Mark VIe systems? Yes. It is designed specifically for EGD communication environments commonly used in GE turbine control systems. Does the module support remote control commands? Yes. It supports consumer-side commands such as reset, trip multiply, and alarm inhibit functions.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/91-01-01-01 EGD Gateway Module
Overview The Bently Nevada 3500/91-01-01-01 is a dedicated Ethernet Global Data (EGD) gateway module developed for the 3500 Machinery Protection System. The module provides deterministic Ethernet communication between the 3500 monitoring rack and external automation platforms including GE Mark VI/Mark VIe turbine controllers, DCS systems, and industrial SCADA networks. This communication interface transfers machinery protection data, channel diagnostics, alarm conditions, and rack operating parameters across industrial Ethernet networks using EGD v2.01 over UDP/IP. The module is optimized for applications requiring low-latency data transmission and continuous controller synchronization in critical rotating equipment environments. The 3500/91-01-01-01 configuration includes a single RJ-45 10/100BASE-TX Ethernet interface and is designed for installation within standard 3500 rack architectures. Core Functions Ethernet Global Data (EGD) communication interface Real-time rack and channel data transfer High-speed Ethernet connectivity for controller integration Continuous monitoring status transmission Alarm and setpoint synchronization Producer and consumer EGD data support Direct integration with GE turbine control systems Rack-powered operation with hot-swappable capability Technical Specifications Parameter Specification Model Number 3500/91-01-01-01 Product Type EGD Communication Gateway Module Compatible Platform Bently Nevada 3500 Series Communication Protocol EGD Version 2.01 Network Transport UDP/IP Ethernet Standard IEEE 802.3 / IEEE 802.3u Ethernet Speed 10 Mbps / 100 Mbps Network Port Single RJ-45 10/100BASE-TX Typical Power Consumption 7.4 W Power Supply Source 3500 rack backplane Supported Data Types The gateway supports transmission of multiple operational and protection-related data structures, including: Floating-point process variables Rack status information Module diagnostics Channel operating conditions Alarm states Protection setpoints System health parameters EGD Data Exchange Functions Producer Functions Consumer Functions Channel measurements Group Reset Alarm information Alarm Inhibit Setpoint transmission Trip Multiply System diagnostics Special Alarm Inhibit Module status Remote control commands Mechanical Specifications Item Details Dimensions 241.3 × 24.4 × 241.8 mm Weight 0.79 kg Front Slot Requirement 1 full-height slot Rear I/O Requirement 1 dedicated rear slot Environmental Specifications Parameter Value Operating Temperature -30°C to +65°C Storage Temperature -40°C to +85°C Relative Humidity Up to 95% non-condensing Vibration Resistance Conforms to 3500 system requirements Front Panel Indicators Integrated LEDs provide immediate visual indication of module and communication status. Indicator Function OK Module operational status TX/RX Ethernet communication activity Industrial Applications The Bently Nevada 3500/91-01-01-01 module is commonly applied in industrial systems requiring fast Ethernet-based machinery monitoring integration, including: Steam and gas turbine protection Compressor monitoring systems Pipeline pumping stations Refinery process equipment Power generation facilities Offshore rotating machinery systems Industrial DCS and SCADA networks 3500/91-01-01-01 vs 3500/90 Communication Modules Feature 3500/91-01-01-01 3500/90 Primary Protocol EGD Modbus TCP/RTU Network Architecture Real-time Ethernet General-purpose communication Controller Integration GE Mark VI/VIe PLC/DCS platforms Ethernet Port Type Single RJ-45 Ethernet and serial options Data Exchange Model Producer/Consumer Polling-based FAQ What is the function of the 3500/91-01-01-01 module? The module enables high-speed Ethernet communication between the 3500 machinery protection rack and external automation systems using the EGD protocol. Which Ethernet interface is included in this version? This configuration includes a single RJ-45 10/100BASE-TX Ethernet port for copper network connections. Can the module communicate with GE turbine controllers? Yes. The module is specifically designed for integration with GE Mark VI and Mark VIe control systems using Ethernet Global Data communication. Does the module support hot replacement? Yes. The module supports hot-swappable installation within compatible 3500 rack configurations.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/91-01-01-00 EGD Gateway Module
Overview The Bently Nevada 3500/91-01-01-00 is an Ethernet Global Data (EGD) communication module engineered for the 3500 Machinery Protection System. It establishes a high-speed Ethernet interface between the 3500 rack and external industrial control platforms, enabling deterministic data transfer for turbine control, process automation, and machinery monitoring applications. Designed for integration with GE control environments and other EGD-compatible systems, the module exchanges rack measurements, alarm states, module diagnostics, and operational parameters using producer/consumer communication architecture over UDP/IP Ethernet networks. The gateway supports real-time industrial communication where fast data acquisition and low-latency transmission are critical for rotating equipment protection systems. Key Functions Real-time EGD data communication over Ethernet Rack-wide data acquisition from 3500 monitoring systems Producer/consumer data exchange architecture Integration with GE Mark VIe and compatible controllers Continuous transmission of dynamic and static machinery data Remote alarm handling and rack command support Dual-speed Ethernet network compatibility Industrial-grade environmental and EMC compliance Technical Specifications ParameterSpecification Model 3500/91-01-01-00 Product Type EGD Communication Gateway Module System Platform Bently Nevada 3500 Series Communication Protocol EGD v2.01 Ethernet Protocol UDP/IP Ethernet Standards IEEE 802.3, IEEE 802.3u Ethernet Speed 10 Mbps / 100 Mbps Network Interfaces 10BASE-T, 100BASE-TX, optional 100BASE-FX Power Consumption 7.4 W typical Rack Power Source Supplied by 3500 rack Module Installation Front module with rear I/O module Network Interfaces Interface TypeConnector Copper Ethernet RJ-45 Fiber Ethernet (optional) MT-RJ The optional fiber interface supports 100BASE-FX communication for installations requiring extended distance or enhanced electromagnetic noise immunity. Data Exchange Capabilities The module supports both producer and consumer communication functions within EGD-based control architectures. Producer Data Rack operational status Module health information Channel condition monitoring Floating-point process variables Alarm setpoints Dynamic machinery measurements Consumer Commands Group Reset Group Trip Multiply Group Alarm Inhibit Group Special Alarm Inhibit Physical Specifications ItemValue Dimensions 241.3 × 24.4 × 241.8 mm Weight 0.79 kg Front Slot Requirement 1 full-height slot Rear Slot Requirement 1 full-height I/O slot Environmental Specifications ParameterSpecification Operating Temperature -30°C to +65°C Storage Temperature -40°C to +85°C Relative Humidity 95% non-condensing EMC Compliance EN 61000-6-2 / EN 61000-6-4 Status Indicators Integrated front-panel LEDs provide rapid diagnostics and communication monitoring. IndicatorDescription OK Module operating status TX/RX Ethernet activity indication Compliance and Certifications StandardCompliance Electrical Safety EN 61010-1 EMC EN 61000 Series Marine Certifications ABS, DNV-GL Hazardous Area Support CSA, ATEX, IECEx compatible systems Typical Applications The Bently Nevada 3500/91-01-01-00 gateway module is commonly installed in critical machinery protection systems including: Gas turbine monitoring Steam turbine protection Pipeline compressor stations LNG processing facilities Refinery rotating equipment Offshore production systems Power generation plants High-speed compressor trains Comparison: 3500/91 vs 3500/90 Feature3500/913500/90 Primary Communication EGD Ethernet Modbus TCP / Serial Communication Architecture Producer/Consumer Polling-based Typical Integration GE Mark VIe PLC / DCS / SCADA Network Type Real-time Ethernet General industrial communication Response Performance High-speed deterministic Standard monitoring communication FAQ What is the main purpose of the 3500/91-01-01-00 module? The module provides high-speed Ethernet communication between a 3500 monitoring rack and external control systems using the EGD protocol. Does the module support fiber Ethernet connections? Yes. Certain configurations support optional 100BASE-FX fiber-optic communication through an MT-RJ interface. Which controllers are compatible with this gateway? The module is widely integrated with GE Mark VIe turbine controllers and other EGD-compatible automation platforms. Can the gateway receive external commands? Yes. The module supports consumer functions including reset commands and alarm inhibit controls.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/91 EGD Communication Gateway Module
Overview The Bently Nevada 3500/91 EGD Communication Gateway Module is an industrial communication interface designed for the 3500 Machinery Protection System. This module enables high-speed data exchange between the 3500 monitoring rack and external control platforms including distributed control systems (DCS), PLCs, SCADA platforms, and turbine control systems. Unlike standard Modbus-only communication modules, the 3500/91 supports Ethernet Global Data (EGD) communication for deterministic data transfer in controller-based environments such as GE Mark VIe systems. The module continuously acquires dynamic machinery measurements and rack status information, delivering real-time data access suitable for critical rotating equipment applications. The gateway is engineered for power generation, oil and gas, petrochemical, and heavy industrial facilities requiring reliable machinery protection integration over Ethernet networks. Key Features High-speed Ethernet Global Data (EGD) communication Real-time transmission of rack monitoring data Compatible with GE Mark VIe and EGD-enabled controllers Continuous access to vibration and protection measurements Supports rack-wide status and alarm reporting Designed for controller response applications Rack-powered module with single-slot installation Industrial-grade EMC and environmental performance Technical Specifications ParameterSpecification Product Model 3500/91 Product Type EGD Communication Gateway Module System Compatibility Bently Nevada 3500 Series Installation Type Rack-mounted Slot Requirement Single-slot module Power Consumption 7.4 W Power Source Supplied by 3500 rack Communication Method Ethernet Global Data (EGD) Ethernet Interface Industrial Ethernet Protocol Support EGD Data Exchange Type Real-time controller communication Monitored Data Transmission The module provides access to comprehensive rack information, including: Overall vibration values Radial vibration measurements Axial position data Speed and Keyphasor® signals Temperature channels Alarm and danger states Channel OK and module status Rack event information System diagnostic data Communication Performance FeatureDetails Network Function Deterministic Ethernet communication Controller Compatibility GE Mark VIe and EGD-capable systems Response Capability Suitable for fast-response control applications Data Access Rack-wide parameter acquisition Integration Method Ethernet-based industrial automation networks Physical Specifications ItemValue Dimensions (H × W × D) 241.3 mm × 24.4 mm × 241.8 mm Weight 0.79 kg Module Format Full-height rack module Environmental Specifications ParameterSpecification Operating Temperature -30°C to +65°C Storage Temperature -40°C to +85°C Humidity Up to 95% non-condensing EMC Compliance Industrial EMC compliant LED Status Indicators The front panel includes integrated diagnostic LEDs for operational monitoring: IndicatorFunction OK Module operating condition TX/RX Ethernet communication activity Bypass Indicates bypass operation status Application Industries The Bently Nevada 3500/91 communication gateway is commonly deployed in: Gas turbine control systems Steam turbine monitoring Compressor protection systems Power generation facilities LNG and petrochemical plants Offshore production platforms Critical rotating machinery systems 3500/91 vs 3500/90 Communication Module Feature3500/913500/90 Primary Communication EGD Ethernet Modbus TCP / Serial Network Type Deterministic controller network General industrial communication Typical Integration GE Mark VIe systems PLC/DCS/SCADA Communication Speed High-speed Ethernet Ethernet and serial Application Focus Turbine control integration General plant connectivity FAQ What is the primary function of the 3500/91 module? The module transfers real-time machinery protection and monitoring data from a 3500 rack to external Ethernet-based control systems using the EGD protocol. Does the 3500/91 support Modbus communication? The 3500/91 is primarily designed for Ethernet Global Data (EGD) communication. Modbus-based communication is typically handled by the 3500/90 gateway module. Which systems commonly use the 3500/91 gateway? The module is widely used with GE turbine control platforms such as Mark VIe systems and other EGD-compatible industrial controllers. Can the module transmit alarm and diagnostic information? Yes. The gateway communicates rack alarms, module diagnostics, event data, and operational status in addition to process measurements.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/90 125728-01 Communication Gateway Module
Product Description The Bently Nevada 3500/90 (P/N 125728-01) is a communication interface module developed for the 3500 Machinery Protection System. The module serves as the central data exchange interface between the 3500 rack and external automation platforms including DCS, PLC, SCADA, and condition monitoring systems. Installed directly within the 3500 rack, the communication gateway gathers operational information from all installed monitor modules and distributes the data through industrial communication protocols. Parameters such as vibration, shaft position, speed, temperature, alarm status, and event records can be transmitted digitally without requiring extensive point-to-point field wiring. The module supports both serial and Ethernet communication methods, making it suitable for integration into modern industrial control networks and remote monitoring architectures. Main Features Central communication interface for 3500 systems Real-time rack data acquisition and transmission Ethernet and serial communication support Compatible with Modbus RTU and Modbus TCP Alarm and event data reporting Supports system integration with PLC and DCS platforms Reduces conventional hardwired signal requirements LED diagnostics for communication and module status Technical Specifications Parameter Specification Product Type Communication Gateway Module Model 3500/90 Part Number 125728-01 System Compatibility Bently Nevada 3500 Series Installation Rack-mounted Country of Origin USA Power Source Supplied by 3500 rack Typical Power Consumption Approximately 5 W Communication Interfaces Interface Details Ethernet TCP/IP communication Serial Interfaces RS-232, RS-422, RS-485 Serial Baud Rate Up to 115.2 kbps Ethernet Speed Up to 100 Mbps Supported Protocols The 3500/90 125728-01 communication module supports several industrial communication standards: Modbus RTU Modbus TCP OPC interface support Bently Nevada proprietary communication protocols Protocol availability may vary depending on firmware revision and system configuration. Functional Capabilities Function Description Rack Data Collection Retrieves measurements from all installed modules Alarm Reporting Transfers alarm and shutdown information Event Logging Communicates event and status records Real-Time Monitoring Supports continuous machinery data transmission Network Integration Connects 3500 systems to plant control networks Keyphasor® Distribution Supports timing reference integration at system level Environmental Specifications Parameter Value Operating Temperature -30°C to +65°C Extended Operating Range Up to +70°C depending on revision Storage Temperature -40°C to +85°C Humidity Up to 95% non-condensing Physical Characteristics Item Specification Approximate Dimensions 160 × 160 × 120 mm Weight 0.8 kg Form Factor Rack-mounted communication module Typical Applications The Bently Nevada 3500/90 module is widely used in industrial machinery monitoring systems including: Steam turbine protection systems Gas turbine monitoring Compressors and pump trains Offshore and marine rotating equipment Oil and gas processing facilities Power generation plants Petrochemical machinery protection systems Integration Advantages The communication gateway simplifies integration between the 3500 rack and plant-wide automation systems by centralizing machinery data access through digital protocols. This architecture helps reduce installation complexity while improving access to vibration and protection data for operators and maintenance personnel. FAQ What is the purpose of the 3500/90 module? The module functions as the communication interface between the 3500 rack and external control or monitoring systems such as PLC, DCS, or SCADA platforms. Does the module support Ethernet communication? Yes. The unit supports Ethernet TCP/IP communication in addition to serial interfaces including RS-232, RS-422, and RS-485. Can the 3500/90 transmit alarm information? Yes. The module transfers alarm conditions, event data, machinery measurements, and status information from the entire 3500 rack.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/72M 140734-08 Position Monitor Module
Product Description The Bently Nevada 3500/72M (P/N 140734-08) is a four-channel position monitoring module designed for use within the 3500 Machinery Protection System. The module interfaces with proximity probe systems to perform continuous position and displacement measurement on rotating and reciprocating equipment. This monitor processes raw probe signals into calibrated engineering values including shaft axial position, rod position, thermal expansion, and dynamic displacement measurements. Integrated alarm logic enables continuous comparison against configured operating limits for machinery protection and condition assessment. The module is commonly applied in turbine, compressor, and thrust monitoring systems where accurate displacement monitoring and shutdown protection are required. Core Functions Continuous shaft position monitoring Rod position measurement for reciprocating compressors Dynamic displacement analysis Axial thrust monitoring Thermal growth and casing expansion detection Alarm processing with programmable thresholds Buffered signal output for external diagnostics Keyphasor® phase reference support Technical Specifications ParameterSpecification Product Type Position Monitor Module Model 3500/72M Part Number 140734-08 System Compatibility Bently Nevada 3500 Series Monitoring Channels 4 independent channels Supported Sensors Proximity probes and Proximitor® systems Compatible Probe Sizes 5 mm, 8 mm, 11 mm Input Signal Types DC gap voltage and dynamic displacement Typical Gap Voltage Range -10 VDC to -22 VDC Typical Displacement Range Up to 2 mm depending on probe type Input Impedance High impedance Measurement Accuracy ±0.5% of full scale Resolution Better than 0.1% of full scale Update Time Less than 100 ms Power Consumption Approximately 7 W Rack Format Single-slot 3500 module Country of Origin USA Measurement Capabilities Each channel can be configured for one or more of the following monitoring functions: Measurement FunctionDescription Shaft Position Continuous axial displacement monitoring Rod Position Position tracking for reciprocating machinery Dynamic Displacement AC vibration and movement analysis Thermal Expansion Machine casing or rotor growth measurement Phase Reference Keyphasor®-based timing reference Thrust Monitoring Bearing wear and axial movement supervision Output Specifications Output TypeSpecification Recorder Outputs 4–20 mA proportional outputs Maximum Load Resistance 600 Ω Recorder Resolution 0.366 μA Buffered Outputs One coaxial connector per channel Buffered Signal Raw transducer output Output Protection Short-circuit protected Alarm & Protection Functions The 3500/72M 140734-08 supports configurable machine protection features including: Alert and Danger alarm levels per channel Latching or non-latching alarm operation Relay interaction through the 3500/32M relay module Front-panel diagnostic LEDs: OK TX/RX Bypass Environmental Specifications ItemValue Operating Temperature -30°C to +65°C Weight 0.85 kg Installation Method Rack-mounted Environmental Application Industrial machinery protection systems Typical Applications The Bently Nevada 3500/72M module is widely used in: Steam turbines Gas turbines Centrifugal compressors Reciprocating compressors Thrust bearing monitoring systems Axial shaft displacement applications Thermal casing expansion monitoring FAQ What transducers are compatible with the 3500/72M? The module supports Bently Nevada proximity probe systems including probes, extension cables, and Proximitor® sensors in 5 mm, 8 mm, and 11 mm configurations. Can the module monitor both static and dynamic measurements? Yes. The monitor processes DC gap voltage for static position measurement and AC components for dynamic displacement analysis. Is shutdown protection supported? Yes. When integrated with a 3500/32M relay module, the system can initiate machinery shutdown logic based on configured alarm conditions.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/72M Recip Rod Position Monitor
Product Description The Bently Nevada 3500/72M is a four-channel reciprocating compressor monitoring module developed for integration within the 3500 Machinery Protection System. The monitor receives signals from proximity transducers, processes both dynamic and static rod position data, and continuously evaluates operating conditions against programmable protection thresholds. Engineered specifically for reciprocating compressor applications, the module supports machinery condition monitoring, rod drop analysis, and shutdown protection functions. Each channel can be configured independently to generate multiple measured variables, allowing flexible monitoring strategies for compressor cylinders, crossheads, and piston rod movement. Using 3500 Rack Configuration Software, users can define Alert and Danger alarm limits, activate relay outputs, and configure measurement logic according to machine operating requirements. Key Features Four independent monitoring channels Designed for reciprocating compressor protection systems Supports static and dynamic rod position measurements Continuous comparison against configurable alarm limits Compatible with Bently Nevada 3500 racks Buffered outputs for diagnostics and analysis equipment Front-panel communication and status indicators Supports relay activation through 3500 system modules Monitoring Capabilities The 3500/72M module can process and monitor several compressor-related parameters, including: Rod Position Rod Drop Hyper Compressor Position Dynamic Position Differential Expansion-Style Measurements Gap Voltage Monitoring Phase Reference Measurements Each channel may be configured for individual measurement functions depending on compressor design and sensor arrangement. Technical Specifications ParameterSpecification Product Type Recip Rod Position Monitor Model 3500/72M System Platform Bently Nevada 3500 Series Channels 4 independent channels Sensor Compatibility Proximity probes and position transducers Signal Type Static and dynamic position signals Transducer Power Supply -24 VDC Buffered Output Impedance 510 Ω Recorder Outputs 4–20 mA proportional outputs Maximum Recorder Load 600 Ω Output Update Rate Less than 100 ms Alarm Configuration Alert and Danger setpoints Alarm Modes Latching or non-latching Front Panel Indicators OK, TX/RX, Bypass Power Consumption Approximately 7 W Rack Compatibility 3500 Machinery Protection System Input Characteristics ItemSpecification Input Channels Four Supported Sensors Proximity probes, displacement transducers Input Signal Conditioning Dynamic and static position processing Signal Comparison Continuous against configured limits Configuration Method 3500 Rack Configuration Software Environmental & Physical Data ParameterValue Operating Temperature -30°C to +65°C Weight 0.85 kg Installation Type Rack-mounted module Country of Origin USA Application Areas The Bently Nevada 3500/72M monitor is commonly installed in: Reciprocating compressors Hyper compressor systems Petrochemical compressor trains Gas processing plants Refinery compression systems Heavy-duty industrial machinery protection systems System Integration When combined with other Bently Nevada 3500 modules, the 3500/72M can participate in: Compressor shutdown logic Alarm annunciation systems Condition monitoring platforms Distributed control systems (DCS) Predictive maintenance programs FAQ What is the primary function of the 3500/72M module? The module monitors reciprocating compressor rod position and related displacement measurements to help protect machinery from abnormal operating conditions. Can the module generate analog outputs for external systems? Yes. The unit provides proportional 4–20 mA recorder outputs for connection to PLC, DCS, and monitoring systems. Does the 3500/72M support alarm functions? Yes. Each channel supports programmable Alert and Danger setpoints with configurable relay interaction through the 3500 platform.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/70M 136449-09 Recip Velocity Monitor
Product Description The Bently Nevada 3500/70M (P/N 136449-09) is a dedicated reciprocating compressor monitoring module engineered for the 3500 Machinery Protection System. This 4-channel monitor acquires vibration data from seismic transducers and converts the signals into machinery condition parameters used for protection, diagnostics, and process monitoring. Designed for compressor applications, the module continuously evaluates vibration conditions against configurable Alert and Danger thresholds to support early fault detection and machine shutdown protection. It supports multiple monitoring modes for crankcase, frame, and crosshead vibration analysis in reciprocating machinery environments. The module integrates signal conditioning, alarm processing, buffered outputs, and recorder outputs within a single rack-based protection platform. Channel pairs can be configured independently for different measurement strategies depending on compressor operating requirements. Key Features Four-channel reciprocating compressor vibration monitor Compatible with Bently Nevada 3500 protection racks Supports seismic acceleration and velocity transducers Continuous machinery protection with configurable alarm logic Buffered outputs for external analysis equipment Recorder outputs for DCS and PLC integration Front-panel diagnostic LED indicators Designed for high-reliability industrial compressor systems Monitoring Functions Each channel pair can simultaneously perform one or two monitoring functions: Impulse Acceleration Acceleration 2 Reciprocating Velocity Low-Frequency Reciprocating Velocity Technical Specifications ParameterSpecification Product Type Recip Impulse Velocity Monitor Model 3500/70M Part Number 136449-09 System Compatibility Bently Nevada 3500 Series Input Channels 4 seismic transducer inputs Power Consumption 7.7 W nominal Acceleration Input Impedance 10 kΩ Velocity Input Impedance 1 MΩ Special Inhibit Input Contact closure, 5 VDC @ 390 μA Recorder Output Range +4 to +20 mA Recorder Load Resistance 600 Ω maximum Recorder Update Rate Less than 100 ms Recorder Resolution 0.3662 μA Recorder Accuracy ±0.05 mA typical Buffered Output One coaxial connector per channel Buffered Output Impedance 550 Ω typical Transducer Supply Voltage –22 VDC minimum Transducer Supply Current 40 mA maximum Short Circuit Protection Supported Communication Indicators OK, TX/RX, Bypass LEDs Sensitivity Ranges Measurement TypeSensitivity Impulse Acceleration 0.51–11.72 mV/(m/s²) Acceleration 2 0.51–11.72 mV/(m/s²) Recip Velocity 3.54–22.64 mV/(mm/s) Low-Frequency Recip Velocity 3.54–22.64 mV/(mm/s) Physical Specifications ItemValue Dimensions 2.6 cm × 25.6 cm × 24.4 cm Weight 0.85 kg Country of Origin USA Mounting Style 3500 Rack Installation Application Areas The Bently Nevada 3500/70M 136449-09 module is commonly installed in: Reciprocating compressors Petrochemical processing units Natural gas compression stations Refinery rotating equipment systems Heavy industrial vibration protection systems Compressor skid monitoring applications Operational Notes Some third-party industrial listings reference additional values such as 220 V operating voltage, 50 kHz frequency response, stainless steel construction, and extended temperature ranges. These specifications are not standard published parameters for the rack module itself and should be validated against official Bently Nevada documentation before project implementation. FAQ What machinery is the 3500/70M designed for? The module is optimized for reciprocating compressors and associated vibration monitoring applications within the Bently Nevada 3500 protection platform. Can the module provide analog outputs to external systems? Yes. The unit includes proportional 4–20 mA recorder outputs for connection to PLC, DCS, or plant monitoring systems. Does the module support real-time machinery protection? Yes. The monitor continuously compares vibration measurements against configured alarm setpoints and can initiate protection responses through the 3500 system.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/70M Recip Impulse Velocity Monitor
Product Overview The Bently Nevada 3500/70M is a dedicated machinery protection module developed for reciprocating compressors and low-speed industrial equipment operating within the 3500 monitoring platform. The monitor combines vibration analysis, impulse detection, and velocity measurement in a single rack-based module. It continuously evaluates mechanical behavior to identify abnormal impact events, looseness, valve deterioration, and piston-related faults before they lead to unscheduled shutdowns or severe mechanical damage. Designed for high-reliability process industries, the 3500/70M provides real-time protection functions together with long-term condition monitoring capabilities. Core Monitoring Functions The 3500/70M performs dynamic vibration analysis using configurable signal processing techniques optimized for reciprocating machinery. Main operating functions include: Continuous casing vibration monitoring Reciprocating impact detection Rod and shaft motion supervision High-frequency acceleration analysis Machinery protection alarm processing Real-time signal conditioning and filtering Relay activation through the 3500 rack system Integration with plant monitoring and diagnostic software The module is optimized for machinery exhibiting cyclic impact behavior that conventional vibration monitors may not accurately detect. Input and Sensor Compatibility The monitor supports multiple industrial transducer types used in compressor protection systems. Sensor Type Application Velocity Transducers Casing vibration monitoring Velomitors Low-frequency machinery analysis Proximity Probes Rod position and shaft movement Acceleration Sensors Impact and impulse detection The module accepts independently configurable inputs across four monitoring channels. Monitoring Parameters Reciprocating Impulse Monitoring Designed to identify repetitive mechanical impacts associated with: Loose crosshead assemblies Damaged rider bands Valve degradation Piston slap Liquid slugging events Mechanical looseness Velocity Monitoring Measures casing vibration levels in: Inches per second (ips) Millimeters per second (mm/s) Peak and RMS processing methods are supported. Acceleration Monitoring High-frequency acceleration analysis enables early identification of impact-related mechanical faults. Technical Specifications Parameter Specification Model 3500/70M Product Type Reciprocating Impulse / Velocity Monitor Manufacturer Bently Nevada System Compatibility 3500 Machinery Protection System Monitoring Channels 4 Independent Channels Input Types Velocity, Proximity, Acceleration Signal Processing Digital filtering and conditioning Alarm Functions Alert and Danger setpoints Alarm Delay 0.1 to 60 seconds programmable Relay Compatibility 3500 rack relay modules Buffered Outputs Front-panel BNC connectors Communication Indicators TX/RX LED status Bypass Indication Front-panel bypass LED Operating Temperature -30°C to +65°C Storage Temperature -40°C to +85°C Humidity Rating 95% non-condensing Rack Requirement Single-slot 3500 rack module The module supports integration with rack-based shutdown systems for emergency protection logic. Front Panel Features The front interface of the 3500/70M includes status indicators and buffered outputs for diagnostics and maintenance activities. Indicator Function OK LED Module operating status TX/RX LED Rack communication activity Bypass LED Indicates bypassed channels BNC Buffered Outputs Raw signal access for analyzers Buffered outputs allow portable diagnostic instruments to capture vibration waveforms without interrupting system operation. Typical Industrial Applications The 3500/70M is primarily installed in machinery protection systems for reciprocating equipment operating under critical process conditions. Common applications include: Reciprocating compressors Process gas compressors Hydrogen compressors Pipeline compressor stations Engine-driven compressors Low-speed industrial machinery API 670 machinery protection systems The module is particularly effective for detecting impact-related failures that develop gradually during machine operation. FAQ Q: What machinery is the 3500/70M designed for?The module is intended primarily for reciprocating compressors and other low-speed machinery requiring impact and vibration monitoring. Q: How many channels does the monitor support?The 3500/70M provides four independently configurable monitoring channels. Q: Can the module detect mechanical looseness?Yes. The impulse monitoring algorithms are specifically designed to identify looseness, valve wear, and impact-related faults. Q: Are buffered outputs available for portable analyzers?Yes. Front-panel BNC connectors provide direct access to raw vibration signals for diagnostic equipment.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/65 184469-01 RTD TC Temperature Monitor
Product Overview The Bently Nevada 3500/65 184469-01 is a rack-based temperature monitoring assembly developed for the 3500 Machinery Protection System. The module combination provides continuous thermal supervision for rotating equipment using RTD and thermocouple sensor inputs. The external termination I/O assembly 184469-01 is designed for installations requiring simplified field wiring access, improved shielding performance, and flexible RTD/TC termination arrangements. It is commonly implemented in API 670 compliant turbine and compressor monitoring systems where long-term reliability and maintainability are essential. The monitor supports independent channel configuration, alarm processing, and integration with machinery condition monitoring platforms. System Functions The 3500/65 184469-01 performs temperature acquisition, signal conditioning, and protection processing for industrial machinery applications. Key operational capabilities include: Six independent temperature input channels RTD and thermocouple sensor compatibility Continuous signal conversion for rack processing Channel-based Alert and Danger alarms Sensor fault diagnostics and integrity monitoring Digital filtering and signal stabilization Communication with System 1 monitoring software Compatibility with recorder output modules for 4–20 mA transmission Each channel can be configured individually according to the sensor type and operating range. Supported Temperature Sensors RTD Sensor Compatibility RTD Type Wiring Configuration Pt100 Platinum RTD 2-wire / 3-wire / 4-wire Ni120 Nickel RTD Supported Cu10 Copper RTD Supported Thermocouple Compatibility Thermocouple Type Typical Usage Type J Industrial process equipment Type K Turbine and exhaust monitoring Type E High-sensitivity applications Type T Low-temperature environments The 184469-01 I/O assembly incorporates cold junction compensation support for thermocouple stability and measurement accuracy. Technical Specifications Parameter Specification Model 3500/65 184469-01 Product Type RTD / Thermocouple Temperature Monitor Manufacturer Bently Nevada System Platform 3500 Machinery Protection System Channel Count 6 Independent Channels Sensor Types RTD and Thermocouple RTD Support Pt100, Ni120, Cu10 Thermocouple Support J, K, E, T Termination Method External Terminal Block I/O Module 184469-01 Alarm Functions Alert and Danger Signal Processing High-resolution digital conversion Diagnostics Open circuit, short circuit, out-of-range detection Isolation Channel-to-channel and channel-to-ground Operating Temperature -30°C to +65°C Humidity Rating 95% non-condensing Mounting 3500 Rack System Dimensions 24.1 × 2.6 × 11.2 cm Weight 0.45 kg The external termination design simplifies commissioning and field maintenance in large industrial cabinets. Features of the 184469-01 External I/O Module The 184469-01 differs from standard internal termination modules by offering enhanced field accessibility and specialized termination architecture. Notable design characteristics include: External screw-terminal wiring interface Improved shielding and grounding structure Support for complex OEM sensor wiring layouts Easier cable inspection and maintenance access Reduced disturbance during service procedures Optimized signal routing for electrically noisy environments This configuration is frequently selected for turbine packages and compressor skids requiring organized external wiring infrastructure. Industrial Applications The 3500/65 184469-01 assembly is commonly used in thermal protection systems for critical machinery. Typical installation environments include: Steam and gas turbines Centrifugal compressors Industrial pumps Generator temperature protection systems Gearbox thermal monitoring Lubrication oil temperature supervision Seal oil and auxiliary process systems The module is particularly suited for installations where external termination accessibility is a maintenance requirement. FAQ Q: Does the 3500/65 support both RTD and thermocouple sensors simultaneously?Yes. Individual channels can be independently configured for RTD or thermocouple operation. Q: What is the purpose of the 184469-01 module?The 184469-01 provides an external field termination interface for sensor wiring connected to the 3500/65 monitor. Q: Is the module suitable for API 670 applications?Yes. The configuration is commonly used in API 670 compliant machinery protection systems. Q: What advantages does external termination provide?External termination improves field wiring accessibility, simplifies maintenance, and reduces downtime during service procedures.
$200.00 $100.00
You have seen 24 out of 607 products