General Electric (GE) offers a comprehensive range of industrial automation products. Its portfolio includes PACSystems RX3i/RX7i, Genius I/O modules, Mark VIe controllers, and PLC systems. GE products ensure reliable operation, scalable automation, and long-term support for industrial applications worldwide.
General Electric
-
General Electric GE DS200SIOCG1AEA Serial Input/Output Control Board
GE DS200SIOCG1AEA Serial Input/Output Control Board The GE DS200SIOCG1AEA, also cataloged as the DS200SIOC Serial Input/Output Control Board, operates as a dedicated hardware component for serial data exchange and control signal routing within the GE Mark V Speedtronic turbine control system. It manages RS-232, RS-485, and optional fiber communication interfaces between controllers and external subsystems. Hardware Specifications Parameter Specification Model DS200SIOCG1AEA Brand GE Origin USA Weight 0.4 kg Operating Temp 0 deg C to +55 deg C Power Consumption Not specified; powered through Mark V backplane (+5 VDC, +/-15 VDC) Product Type Serial Input/Output Control Board Series Mark V Speedtronic turbine control system Communication Interfaces RS-232, RS-485, optional fiber-optic links depending on revision Processor Dedicated communication processor Memory PROM firmware storage and EEPROM configuration storage Assembly Type Normal Assembly Revision Quantity 3 revisions Firmware Compatibility and Industrial Network Processing The DS200SIOCG1AEA uses a dedicated communication processor to handle serial protocol execution, data transfer, and controller-to-device interface functions. Within the Mark V platform, the board manages serial communication paths through RS-232 and RS-485 interfaces while supporting revision-dependent fiber-optic communication options. The GE Mark V architecture requires firmware and hardware revision matching for proper backplane operation. PROM-based firmware storage and EEPROM parameter retention provide configuration support for communication functions. Diagnostic LEDs, processor reset control, and onboard test points provide local status verification. Frequently Asked Questions Q: What communication interfaces are supported by the DS200SIOCG1AEA?A: The board supports RS-232 and RS-485 serial communication interfaces. Fiber-optic communication capability depends on the specific hardware revision. Q: How is the DS200SIOCG1AEA powered inside the Mark V system?A: The board receives operating power through the Mark V backplane, including +5 VDC and +/-15 VDC supply rails. Q: Can the board revision be changed without system verification?A: No. Hardware revision and firmware compatibility must be checked against the installed Mark V controller configuration before replacement. Field Installation Guidelines Install the DS200SIOCG1AEA in the designated Mark V rack backplane slot with power removed from the control cabinet. Verify edge connector alignment before insertion to prevent mechanical damage. Route serial communication cables separately from high-voltage power conductors to reduce electrical interference. Apply proper cable shielding practices, with shield termination following the system grounding design. Confirm RS-232 and RS-485 wiring polarity before energizing the system. After installation, verify backplane seating, communication status LEDs, and controller recognition through standard Mark V diagnostic procedures.
$200.00 $100.00
-
General Electric GE DS200LDCCG1AAA LAN Drive Control Card
GE DS200LDCCG1AAA LAN Drive Control Card The GE DS200LDCCG1AAA, also cataloged as the DS200LDCC LAN Drive Control Card, operates as a dedicated hardware component for LAN communication and drive control processing within GE Mark V Speedtronic turbine control system platforms. It manages controller data exchange, motor processing, and drive interface operations through integrated processor circuits. Suffix Breakdown & Model Matrix Segment Description DS200 GE Mark V board family designation LDCC LAN Drive Control Card functional acronym G1 Hardware configuration identifier A Functional revision 1 A Functional revision 2 A Artwork revision Hardware Specifications Parameter Specification Model DS200LDCCG1AAA Brand GE Origin United States Weight 0.8 kg Operating Temp -10 to +60 deg C Power Consumption 20 W Product Type Drive Control LAN Communication Boards Series Mark V Speedtronic Functional Acronym LDCC Functional Description Drive Control/LAN Communications Board Power Supply +5 VDC, +/-15 VDC via backplane Operating Voltage 24 VDC Power Requirements +5 VDC, 7 A Input Voltage 90-264 VAC Output Voltage 0-10 VDC Frequency 50/60 Hz Isolation Voltage 1500 VAC Current Rating (Exciter Control) 10 A to 30 A Microprocessors LCP, DCP, MCP, CMP Memory 6 PROMs and EEPROM Connectors Mark V rack backplane edge connector Diagnostics RESET button, LED keypad display, bar graph LEDs PCB Coating Conformal coating GE Mark V Processor Communication and Drive Control Interface The DS200LDCCG1AAA integrates multiple processor units for distributed drive control and LAN communication tasks. The LAN Control Processor (LCP) manages communication exchange and bus conversion, while the Drive Control Processor (DCP) handles peripheral I/O processing and analog/digital conversion functions. The Motor Control Processor (MCP) and Co-Motor Processor (CMP) provide additional processing paths for motor control circuits and interface operations. This architecture supports deterministic data exchange between GE Mark V controller modules, exciter systems, and drive assemblies. Firmware Flash Compatibility and I/O Processing Architecture The DS200LDCCG1AAA uses PROM-based configuration storage and EEPROM parameter retention for field-adjustable settings. Firmware compatibility is dependent on the installed GE Mark V controller revision and drive configuration. The LDCC board supports I/O density scaling through dedicated processor functions rather than direct field-level control logic. Revision matching between hardware and firmware is required for correct communication behavior within the Mark V rack. Frequently Asked Questions Q: What processor functions are included on the DS200LDCCG1AAA?A: The board contains LAN Control Processor (LCP), Drive Control Processor (DCP), Motor Control Processor (MCP), and Co-Motor Processor (CMP) functions. Q: What diagnostic hardware is available on the DS200LDCCG1AAA?A: The board includes a RESET button, LED keypad display, and bar graph LED indicators for status monitoring and troubleshooting. Q: Can the DS200LDCCG1AAA operate independently from a GE Mark V rack?A: No. The board requires integration with the GE Mark V backplane and associated controller assemblies for communication and control operation. Field Installation Guidelines Install the DS200LDCCG1AAA into the designated GE Mark V rack slot and verify the edge connector is correctly seated before applying system power. Confirm board revision, firmware compatibility, and configuration parameters before replacement or commissioning. Maintain proper grounding between the control rack, cabinet structure, and connected drive equipment. Route LAN communication, feedback, and control wiring separately from high-current power cables. Apply suitable shielding and grounding methods to reduce electrical interference. Inspect connectors, PCB coating condition, and mounting points during installation and maintenance procedures.
$200.00 $100.00
-
General Electric GE DS200LDCCG1ADA LAN Drive Control Card
GE DS200LDCCG1ADA LAN Drive Control Card The GE DS200LDCCG1ADA, also cataloged as the DS200LDCC LAN Drive Control Card, operates as a dedicated hardware component for LAN communication and drive control processing within GE Mark V Speedtronic turbine control system platforms. It executes controller data exchange, motor interface processing, and drive-related signal handling through integrated processors. Hardware Specifications Parameter Specification Model DS200LDCCG1ADA Brand GE Origin United States Weight 0.8 kg Operating Temp -10 to +60 deg C Power Consumption 20 W Product Type Drive Control LAN Communication Boards Series Mark V Speedtronic Functional Acronym LDCC Functional Description Drive Control/LAN Communications Board Power Supply +5 VDC, +/-15 VDC via backplane Additional Supply 24 VDC Current Rating (Exciter Control) 10 A to 30 A Input Voltage 90-264 VAC Output Voltage 0-10 VDC Frequency 50/60 Hz Isolation Voltage 1500 VAC Microprocessors LCP, DCP, MCP, CMP Memory 6 PROMs and EEPROM Diagnostics RESET button, LED keypad display, bar graph LEDs PCB Coating Normal coating Mounting Type GE Mark V rack backplane installation GE Mark V Processor Communication and Drive Interface The DS200LDCCG1ADA integrates multiple processor sections for GE Mark V drive control and LAN communication tasks. The LAN Control Processor (LCP) manages communication exchange and bus conversion, while the Drive Control Processor (DCP), Motor Control Processor (MCP), and Co-Motor Processor (CMP) handle I/O processing, motor control functions, and subsystem data operations. The board supports deterministic controller communication through the Mark V backplane architecture. Its processor-based design enables coordinated handling of drive reset functions, operator interface processing, and exciter control communication. Firmware Flash Compatibility and Backplane Communication The DS200LDCCG1ADA uses programmable memory devices including PROM storage for configuration and EEPROM storage for field parameters. Firmware compatibility depends on the installed GE Mark V controller revision and drive system configuration. The LDCC hardware supports I/O density scaling through distributed processor handling rather than direct field Ethernet control. Revision identifiers A, D, and A define functional, hardware, and artwork configuration states for system matching. Frequently Asked Questions Q: What processor functions are included on the DS200LDCCG1ADA?A: The board contains LAN Control Processor (LCP), Drive Control Processor (DCP), Motor Control Processor (MCP), and Co-Motor Processor (CMP) sections. Q: What power connections are required for the DS200LDCCG1ADA?A: The board receives controller power through GE Mark V interfaces including +5 VDC, +/-15 VDC, and 24 VDC supply circuits depending on system configuration. Q: Does the DS200LDCCG1ADA provide onboard diagnostics?A: Yes. The board includes a RESET button, LED keypad display, and status indication LEDs for hardware monitoring. Field Installation Guidelines Install the DS200LDCCG1ADA into the assigned GE Mark V rack position and verify the backplane connector is fully seated before energizing the system. Confirm that firmware revision, board configuration, and memory settings match the installed drive control architecture. Maintain correct grounding between the rack assembly and cabinet structure. Route LAN, control, and feedback wiring separately from high-current power conductors. Apply proper cable shielding and grounding practices to reduce electrical interference. Inspect connectors, PCB surfaces, and mounting points during installation and maintenance procedures.
$200.00 $100.00
-
General Electric GE DS200LDCCH1AKA LAN Communication Drive Control Board
GE DS200LDCCH1AKA LAN Communication Drive Control Board The GE DS200LDCCH1AKA, also cataloged as the DS200LDCC LAN Communication Drive Control Board, operates as a dedicated hardware component for LAN data exchange and drive control processing within GE Mark V Speedtronic turbine control system platforms. It executes communication handling, motor processing, and controller interface functions through onboard processors. Suffix Breakdown & Model Matrix Segment Description DS200 GE Mark V board family designation LDCC LAN Communication / Drive Control functional acronym H1 Hardware configuration identifier A Functional revision 1 K Functional revision 2 A Artwork revision Hardware Specifications Parameter Specification Model DS200LDCCH1AKA Brand GE Origin United States Weight 0.5 kg Operating Temp 0 to +55 deg C Power Consumption Not specified Product Type LAN Communication Drive Control Boards Series Mark V Speedtronic Functional Acronym LDCC Functional Description Drive Control/LAN Communications Board Power Supply +5 VDC, +/-15 VDC via backplane Communication Interfaces LAN interface, RJ45 Ethernet, DB9 RS-232 depending on revision Processors LAN Control Processor (LCP), Drive Control Processor (DCP), Motor Control Processor (MCP), Co-Motor Processor (CMP) Memory 6 PROMs for configuration and EEPROM for field parameters Diagnostics RESET button, alphanumeric keypad, LED indicators PCB Coating Conformal coating Mounting Type Mark V rack backplane installation GE Mark V Processor Communication and Drive Control Interface The DS200LDCCH1AKA integrates multiple embedded processors to manage communication exchange and drive control processing within GE Mark V turbine control architectures. The LAN Control Processor handles communication conversion, while the Drive Control Processor and Motor Control Processor execute peripheral I/O handling, analog/digital conversion, and motor control data processing. The board supports deterministic backplane communication between controller modules and connected drive or exciter systems. Its processor-based architecture provides distributed handling of LAN communication tasks, operator interface functions, and drive-related control operations. Firmware Flash Compatibility and Processor Memory Management The DS200LDCCH1AKA uses programmable memory components including PROM devices and EEPROM storage for configuration parameters. Firmware compatibility depends on installed Mark V system revisions and processor configuration requirements. The board revision identifiers A, K, and A represent functional and artwork configuration states. Replacement boards require matching firmware and hardware revision compatibility to maintain controller communication and drive operation. Frequently Asked Questions Q: What processors are integrated into the DS200LDCCH1AKA?A: The board contains four processing sections: LAN Control Processor (LCP), Drive Control Processor (DCP), Motor Control Processor (MCP), and Co-Motor Processor (CMP). Q: Does the DS200LDCCH1AKA communicate directly with external Ethernet networks?A: The board provides LAN communication functions through GE Mark V system interfaces. External connector availability depends on board revision configuration. Q: What diagnostic functions are available on the board?A: The board includes a RESET button, onboard alphanumeric keypad, LED indicators, and diagnostic display functions for troubleshooting. Field Installation Guidelines Install the DS200LDCCH1AKA into the assigned GE Mark V rack slot and verify edge connector engagement before system power application. Confirm processor firmware compatibility, memory configuration, and board revision before installation. Maintain proper grounding between the rack assembly and cabinet structure. Route communication and control wiring separately from high-current power conductors. Use appropriate shielding and grounding practices for communication cables to reduce electrical interference. Inspect RJ45, serial connectors, and backplane contacts for mechanical damage or contamination during maintenance procedures.
$200.00 $100.00
-
General Electric GE DS215TCQAG1BZZ01A TCQA Analog I/O Board
GE DS215TCQAG1BZZ01A TCQA Analog I/O Board The GE DS215TCQAG1BZZ01A, also cataloged as the DS215TCQA Analog I/O Board, operates as a dedicated hardware component for analog signal acquisition and output execution within GE Mark V Speedtronic turbine control system platforms. It processes temperature, pressure, flow, and vibration signals through onboard conversion and conditioning circuits. Suffix Breakdown & Model Matrix Segment Description DS215 GE Mark V board family designation TCQA TCQA analog I/O functional acronym G1 Hardware configuration identifier B Functional revision 1 ZZ Functional revision 2 designation 01A Artwork revision identifier Hardware Specifications Parameter Specification Model DS215TCQAG1BZZ01A Brand GE Origin United States Weight 0.39 kg Dimensions 262 x 185 x 39 mm Operating Temp -40 to +70 deg C Product Type Analog I/O Boards Series Mark V LM Functional Acronym TCQA Functional Description Circuit Board and Firmware Power Supply 24 VDC Input Signals Temperature, pressure, flow, vibration, and analog process signals Output Signals Analog control signals for turbine subsystems Communication Interfaces RS-485, CAN, Modbus TCP/IP depending on revision Signal Processing Analog-to-digital conversion and analog output control PCB Coating Normal coating Mounting Type Mark V rack/backplane installation GE Mark V Analog I/O Processing and Deterministic Control Interface The DS215TCQAG1BZZ01A provides analog input acquisition and output control functions within the GE Mark V LM control platform. The board converts field sensor signals into processed data values and transfers control information through the turbine controller backplane architecture. The TCQA board supports I/O density scaling within Mark V turbine control configurations by handling multiple analog channels through high-density connectors. Signal conditioning circuits perform input stabilization, conversion, and diagnostic verification for connected field devices. GE Mark V Firmware and Backplane Compatibility The DS215TCQAG1BZZ01A includes board-level firmware support for Mark V R/S/T core compatibility. The revision identifiers B and Z define functional modifications and firmware/artwork configuration states that must match the installed control rack requirements. The board uses GE Mark V deterministic communication architecture rather than modern Ethernet field networks. Backplane communication timing is controlled by the associated processor modules for synchronized turbine monitoring and control operations. Frequently Asked Questions Q: Does the DS215TCQAG1BZZ01A operate as a standalone controller?A: No. The TCQA board functions as an analog I/O interface module and requires integration with GE Mark V processor and rack assemblies. Q: What field signals can be connected to the DS215TCQAG1BZZ01A?A: The board processes analog signals including temperature, pressure, flow, vibration, and other turbine monitoring inputs. Q: Are firmware and revision compatibility required for replacement installation?A: Yes. Functional revision and firmware configuration must match the installed Mark V system architecture. Field Installation Guidelines Install the DS215TCQAG1BZZ01A into the designated GE Mark V rack slot and verify backplane connector alignment before applying power. Connect analog field wiring according to cabinet documentation. Use shielded instrumentation cables where required and terminate shields according to grounding practices to reduce noise coupling. Separate analog signal wiring from high-current power conductors. Confirm board revision, firmware compatibility, and connector seating before commissioning the turbine control system.
$200.00 $100.00
-
General Electric GE DS200FSAAG1ABA Flame Safeguard Amplifier Card
GE DS200FSAAG1ABA Flame Safeguard Amplifier Card Configured for flame scanner signal conditioning in GE Mark V Speedtronic turbine control system platforms, the GE DS200FSAAG1ABA (DS200FSAA Flame Safeguard Amplifier Card) provides direct physical/electrical execution of UV/IR flame input processing, logic conversion, and analog output generation for combustion monitoring interfaces. Hardware Specifications Parameter Specification Model DS200FSAAG1ABA Brand GE Origin United States Weight 0.5 kg Operating Temp -30 to +65 deg C Product Type Flame Safeguard Amplifier Cards Series Mark V Speedtronic Functional Acronym FSAA Functional Description Field Supply Amplifier Input Signal Type UV/IR flame scanner signals Logic Supply Voltage 24 VDC nominal Output Signals TTL logic and 4-20 mA scaled output Communication Interface DLAN / serial link to VME backplane PCB Coating Style Normal coating Mounting Type Eurocard / VME backplane slot GE Mark V Flame Signal Processing and Control Interface The DS200FSAAG1ABA processes ultraviolet and infrared flame scanner signals and converts scanner output characteristics into turbine controller-compatible logic states. The card provides flame presence evaluation through signal conditioning circuits and generates TTL logic outputs with 4-20 mA analog scaling for monitoring interfaces. The FSAA board integrates into GE Mark V combustion monitoring architectures through the VME backplane communication structure. The hardware design includes field signal amplification circuits, input conditioning paths, and interface electronics for flame detection feedback. Profinet / EtherNet-IP Deterministic Control Network Compatibility The DS200FSAAG1ABA is part of the GE Mark V industrial control hardware platform and communicates through the DLAN / VME control architecture rather than Ethernet-based field networks. Its deterministic backplane interface supports fixed-cycle signal exchange between turbine control processor assemblies and combustion monitoring hardware. The board revision structure identifies functional and artwork modifications through the A, B, and A suffix configuration. Hardware replacement requires matching revision compatibility with the installed Mark V control rack configuration. Frequently Asked Questions Q: What type of input signal does the DS200FSAAG1ABA process?A: The board accepts UV or IR flame scanner signals and converts them into processed logic and analog monitoring outputs. Q: Does the DS200FSAAG1ABA communicate through Ethernet networks?A: No. The board uses the GE Mark V DLAN / VME backplane communication structure for controller integration. Q: What installation factors affect flame signal accuracy?A: Proper grounding, shield termination, scanner wiring separation, and correct rack installation affect flame signal integrity and prevent unwanted signal interference. Field Installation Guidelines Install the DS200FSAAG1ABA in the designated GE Mark V VME rack slot and confirm connector engagement before applying system power. Verify flame scanner wiring polarity, shielding connections, and cable routing practices according to the turbine control cabinet documentation. Keep flame signal wiring separated from high-current switching circuits to reduce electrical noise coupling. Confirm board revision compatibility, configuration settings, and grounding connections before commissioning. Inspect the conformal-coated PCB surface and connectors for contamination or mechanical damage during maintenance procedures.
$200.00 $100.00
-
General Electric GE DS200DCFBG2BNC DC Feedback Power Supply Boar
GE DS200DCFBG2BNC DC Feedback Power Supply Board The GE DS200DCFBG2BNC, also cataloged as the DS200DCFB DC Feedback Power Supply Board, operates as a dedicated hardware component for regulated DC power distribution and feedback signal processing within GE Mark V Speedtronic turbine control system platforms. It provides control-level voltage regulation, feedback monitoring, and protection circuit execution for drive control interfaces. Hardware Specifications Parameter Specification Model DS200DCFBG2BNC Brand GE Origin United States Weight 0.75 kg Power Consumption Powered from GE Mark V control system supply circuits Product Type DC Feedback Power Supply Boards Series Mark V Speedtronic Assembly Type PCB assembly with conformal coating Connectors 18 plug connectors and 9 stab connectors Configuration Components 7 DIP switches and 12 jumpers Protection Circuits Short-circuit protection, thermal monitoring, fuse indication Fuse Configuration 3 protective fuses with LED/neon status indicators Feedback Functions Voltage and current feedback monitoring GE Mark V DC Power Feedback and Control Interface The DS200DCFBG2BNC integrates DC power regulation and feedback processing functions for GE Mark V turbine control architectures. The board contains voltage/current feedback circuits, protection components, transformers, relays, and switching elements used for controlled power conversion and monitoring. The DS200DCFB board family supports industrial control hardware configuration through DIP switch selections and jumper settings. These configuration elements allow adjustment of AC line voltage selection and DC bridge or motor voltage feedback VCO circuits according to system requirements. Industrial Control Bus and Hardware Configuration The DS200DCFBG2BNC follows GE Speedtronic Mark V hardware design practices for rack-based controller integration. The board revision structure includes functional, hardware, and artwork modifications identified by the B, N, and C revision identifiers. Compatibility with earlier DS200DCFBG2 assemblies allows integration into existing control rack configurations. Frequently Asked Questions Q: Does the DS200DCFBG2BNC contain independent application firmware?A: No. The board operates as a hardware power supply and feedback interface module. Control logic and system diagnostics are executed by connected GE Mark V processor assemblies. Q: What protection functions are integrated into the board?A: The board includes short-circuit protection, thermal monitoring circuits, fuse protection, and LED/neon indicators for fuse status observation. Q: What configuration elements are available on the board?A: The DS200DCFBG2BNC provides DIP switches and jumper points for hardware configuration, including voltage selection and feedback circuit settings. Field Installation Guidelines Install the DS200DCFBG2BNC into the designated GE Mark V rack position and verify all plug and stab connector alignment before applying power. Inspect connector contacts, fuse indicators, and board mounting points during installation. Maintain proper separation between power wiring and low-level feedback signal wiring to reduce electrical noise coupling. Connect grounding and shielding according to GE cabinet wiring practices. Confirm jumper and DIP switch positions match the required turbine control configuration before system startup.
$200.00 $100.00
-
General Electric DS200SVAAG1A GE Voltage Attenuator Board
GE DS200SVAAG1A Voltage Attenuator Board The GE DS200SVAAG1A, also cataloged as the DS200SVAA Voltage Attenuator Board, operates as a dedicated signal conditioning hardware component for analog voltage attenuation within GE Mark V Speedtronic turbine control system platforms. It provides isolated scaling of field voltage inputs into controller-compatible analog levels through passive attenuation circuits and electrical isolation paths. Hardware Specifications Parameter Specification Model DS200SVAAG1A Brand GE Origin United States Weight 0.5 kg Operating Temp -30 to +65 deg C Power Consumption Passive board design; powered by 28 VDC system supply Product Type Voltage Attenuator Board Series Drive Control System Compatibility GE Mark V Speedtronic turbine control system Input Voltage Range Up to +/-200 VAC/VDC depending on configuration Output Voltage Range +/-10 VDC conditioned signal Channels Multiple isolated analog input channels Accuracy +/-0.1% FS Isolation Rating 2500 Vrms channel-to-ground Response Time <5 ms Mounting Type Rack-mount, single-slot Technology Surface mount electronics GE Mark V Analog Signal Attenuation and Isolation The DS200SVAAG1A performs analog voltage scaling between field-level signals and GE Mark V controller input circuits. The board attenuates higher amplitude voltage signals into a +/-10 VDC output range suitable for turbine control processing. Channel isolation supports separation between input circuits and control electronics, reducing ground loop effects and electrical interference. The board architecture follows GE industrial control hardware practices, using surface mount components and rack-based installation within Speedtronic control cabinets. Signal conditioning functions include voltage reduction, analog stabilization, and electrical interface adaptation. Firmware and I/O Interface Characteristics The DS200SVAAG1A operates as a hardware-level interface board without independent firmware execution. Diagnostic information is handled through connected GE Mark V processor and controller boards. The analog interface design supports deterministic signal transfer within turbine control I/O architectures. Frequently Asked Questions Q: Does the DS200SVAAG1A execute application firmware independently?A: No. The board is a passive voltage attenuation and signal conditioning module. Monitoring and control functions are performed by connected GE Mark V processor boards. Q: What signal conversion function does the DS200SVAAG1A provide?A: The board attenuates incoming high-level analog voltage signals and provides conditioned +/-10 VDC outputs for controller processing. Q: What installation factors affect analog signal performance?A: Shielding, grounding practices, cable routing, and separation from high-current conductors affect analog signal integrity. Field Installation Guidelines Install the DS200SVAAG1A in the designated GE Mark V rack slot with the correct backplane connection. Verify board alignment before insertion to prevent connector damage. Use shielded instrumentation wiring for analog signal connections where required. Terminate cable shields according to cabinet grounding practices and avoid routing analog signal cables parallel to high-voltage or high-current wiring. Confirm that field voltage inputs remain within the specified board configuration range before energizing the system. Inspect connectors, terminal points, and rack seating during commissioning procedures.
$200.00 $100.00
-
General Electric GE DS200TCQBG1BCB Analog I/O Board
GE DS200TCQBG1BCB Analog I/O Board The GE DS200TCQBG1BCB, also cataloged as the DS200TCQB Analog I/O Board, operates as a dedicated hardware component for analog signal acquisition, conditioning, and output execution within GE Mark V Speedtronic turbine control systems. Hardware Specifications Parameter Specification Model DS200TCQBG1BCB Brand GE Origin United States Weight 1.0 kg Dimensions 280 x 200 x 30 mm Operating Temp -30 to +65 deg C Power Consumption +5 VDC, 6 A Product Type Analog I/O Boards Series Mark V Functional Acronym TCQB Functional Description RST Extended Analog I/O Board Analog Inputs 8 channels, configurable for 4-20 mA or 0-10 V Analog Outputs 4 channels, +/-10 V or 4-20 mA Resolution 12-16 bit ADC/DAC depending on revision Accuracy +/-0.5% FS Relay Channels 12 channels Field Power Supply 28 VDC Isolation 2500 VAC field-to-logic isolation Connectors Ribbon cable connectors and field terminal blocks GE Mark V Analog Signal Processing and Network Integration The DS200TCQBG1BCB performs analog input acquisition and analog output generation within the GE Mark V control architecture. The board processes field sensor and actuator signals through onboard signal conditioning circuits before exchanging data with Mark V processor modules. The TCQB board supports GE industrial control requirements through I/O density scaling and backplane communication between control modules. Analog channels are configured for current and voltage signal types, allowing connection to turbine instrumentation and control devices. Firmware and hardware compatibility must match the installed Mark V system configuration. Board revision identifiers define supported hardware behavior, including backwards compatibility with earlier TCQB revisions. Frequently Asked Questions Q: What analog signal types are supported by the GE DS200TCQBG1BCB?A: The board supports configurable analog inputs including 4-20 mA and 0-10 V signals, with analog outputs available in +/-10 V and 4-20 mA formats. Q: What power supply rails are required for the DS200TCQBG1BCB?A: The board requires +5 VDC logic power at 6 A and uses analog supply rails for signal processing functions. Q: Is the DS200TCQBG1BCB compatible with non-GE control systems?A: No. The board is designed for GE Mark V Speedtronic systems and requires the corresponding rack, processor modules, and communication interfaces. Field Installation Guidelines Install the DS200TCQBG1BCB according to the GE Mark V rack and wiring configuration requirements. Verify terminal assignments before connecting analog field devices. Use shielded instrumentation cables for low-level analog signals where required. Connect cable shields according to the site grounding standard to reduce electromagnetic interference. Maintain separation between analog signal wiring and high-current power conductors. Before installation, inspect ribbon connectors, terminal blocks, and PCB surfaces for damage or contamination. Apply ESD protection when handling the board. Confirm board revision compatibility and verify analog channel operation after installation and system initialization.
$200.00 $100.00
-
General Electric GE DS200TCPSG1APE Power Supply Board
GE DS200TCPSG1APE Power Supply Board The GE DS200TCPSG1APE, also cataloged as the DS200TCPS Power Supply Board, operates as a dedicated hardware component for regulated DC power conversion and voltage rail distribution within GE Mark V Speedtronic turbine control systems. Hardware Specifications Parameter Specification Model DS200TCPSG1APE Brand GE Origin United States Weight 2.60 lbs Dimensions 280 x 200 x 30 mm Operating Temp -30 to +65 deg C Product Type Power Supply Boards Functional Acronym TCPS Functional Description DC Power Supply Input Board Input Voltage 115/230 VAC, 50/60 Hz DC Outputs +5 VDC @ 15 A, +15 VDC @ 2 A, -15 VDC @ 2 A, +24 VDC @ 1 A Regulation Accuracy +/-2% Ripple and Noise <50 mV RMS Isolation 2500 VAC input-to-output isolation Protection Functions Overvoltage, overcurrent, and thermal shutdown Connectors Backplane edge connector and terminal blocks Cooling Method Convection cooling with optional forced air PCB Coating Normal coating Assembly Type Normal Assembly GE Mark V Power Distribution and Firmware Compatibility The DS200TCPSG1APE provides regulated DC voltage rails for GE Mark V processor and I/O control boards. The board converts incoming AC power into controlled DC outputs required by system modules, including logic and analog supply rails. The power architecture supports GE industrial control platforms through backplane power distribution. Voltage rail monitoring is provided through onboard LED indicators for status verification of the generated supplies. For GE Mark V systems, firmware and hardware revision compatibility must be verified before replacement. The DS200TCPSG1APE includes revision identifiers that define board configuration and compatibility with installed Mark V assemblies. Frequently Asked Questions Q: What DC voltage outputs are generated by the GE DS200TCPSG1APE?A: The board provides regulated +5 VDC, +15 VDC, -15 VDC, and +24 VDC output rails for Mark V control modules. Q: What protection functions are integrated into the DS200TCPSG1APE power supply board?A: The board includes overvoltage protection, overcurrent protection, and thermal shutdown functions for power circuit protection. Q: Can the DS200TCPSG1APE be installed in systems other than GE Mark V?A: No. The board is designed for GE Mark V Speedtronic control systems and requires compatible rack hardware and power distribution connections. Field Installation Guidelines Install the DS200TCPSG1APE in the designated GE Mark V rack position and verify backplane connector alignment before energizing the system. Disconnect input power before board replacement. Inspect terminal blocks, edge connectors, and PCB surfaces for contamination or mechanical damage before installation. Maintain separation between AC input wiring and low-level control signal cables to reduce electrical interference. Follow site grounding procedures for protective earth and shield termination. Use ESD protection when handling the board to prevent damage to power control and monitoring circuits. Confirm voltage rail output measurements and board revision compatibility before returning the Mark V control system to operation.
$200.00 $100.00
-
General Electric GE DS200STBAG1ACB Signal Terminal Board
GE DS200STBAG1ACB Signal Terminal Board Configured for field signal termination and electrical interfacing in GE Mark V Speedtronic turbine control systems, the GE DS200STBAG1ACB (DS200STBA Signal Terminal Board) provides direct physical connection between analog, digital, and drive-related field wiring circuits and processor control modules. Suffix Breakdown & Model Matrix Segment Description DS200 GE Mark V Speedtronic control board family STBA Signal Terminal Board functional acronym G1 Board group / hardware configuration identifier A Functional revision 1 C Functional revision 2 B Artwork revision Hardware Specifications Parameter Specification Model DS200STBAG1ACB Brand GE Origin United States Weight 0.73 lbs Dimensions 280 x 200 x 30 mm Operating Temp -30 to +65 deg C Power Consumption Not specified; powered from Mark V control rack supply Product Type Signal Terminal Boards Functional Acronym STBA Application Platform GE Mark V Speedtronic turbine control system Signal Inputs Analog 4-20 mA, 0-10 V signals and digital 24 VDC signals Signal Outputs Relay and analog output termination interfaces Terminal Interface Field wiring terminal blocks and ribbon cable connectors Isolation 2500 VAC field-to-logic isolation Power Supply +5 VDC logic and +/-15 VDC analog supply rails PCB Coating Normal coating Indicators LED signal activity indicators GE Mark V Signal Interface and Network Integration The DS200STBAG1ACB functions as a field termination interface within GE Mark V control architecture. It provides terminal access for multi-input and multi-output signal circuits, including analog measurement channels, digital status signals, and drive-related wiring connections. The board supports GE industrial control integration through dedicated terminal connections and processor board interfaces. The terminal design separates field wiring from internal control electronics, while the 2500 VAC field-to-logic isolation specification defines the electrical separation between external circuits and controller logic domains. For GE Mark V systems, firmware and hardware compatibility must match the installed control configuration. Board revision identifiers, including functional revision and artwork revision, define the applicable hardware configuration. Frequently Asked Questions Q: What type of signals can the GE DS200STBAG1ACB terminate?A: The DS200STBAG1ACB provides termination interfaces for analog signals such as 4-20 mA and 0-10 V, as well as digital 24 VDC field signals. Q: Does the DS200STBAG1ACB provide electrical isolation between field wiring and control logic?A: Yes. The board specification includes 2500 VAC field-to-logic isolation between external signal circuits and internal control electronics. Q: Is the DS200STBAG1ACB compatible with non-GE control platforms?A: No. The board is designed for GE Mark V Speedtronic turbine control systems and requires the corresponding GE rack, processor modules, and wiring configuration. Field Installation Guidelines Install the DS200STBAG1ACB in the designated GE Mark V rack assembly and verify terminal block assignments before connecting field wiring. Separate low-level analog signal cables from high-current power conductors to reduce electrical noise coupling. Use shielded instrumentation cables where required, with cable shields terminated according to site grounding practices. Inspect terminal contacts, ribbon cable connectors, and PCB surfaces before installation. Handle the board using ESD protection procedures to prevent damage to logic components. Confirm board revision compatibility with the existing Mark V hardware configuration before system startup.
$200.00 $100.00
-
General Electric DS200SDCIG1AFB GE Drive Control Card
GE DS200SDCIG1AFB Drive Control Card The GE DS200SDCIG1AFB, also cataloged as the DS200SDCI Drive Control Card, operates as a dedicated hardware component for drive control processing, signal conditioning, and module communication within GE Mark V Speedtronic turbine control systems. Hardware Specifications Parameter Specification Model DS200SDCIG1AFB Brand GE Origin United States Weight 1.2 kg Operating Temp -30 to +65 deg C Product Type Drive Control Card / Processor Board Processor 16-bit Motorola MC68xxx series CPU Memory EPROM firmware storage and RAM runtime memory I/O Interface Analog and digital signal interfaces through daughter boards Communication Ports RS-232 / RS-485 serial communication interfaces Bus Interface GE Mark V backplane connection Power Input +5 VDC logic and +/-15 VDC analog supply rails Isolation 2500 VAC field-to-logic isolation PCB Protection Conformal coating for dust and moisture resistance Diagnostic Interface On-board LED status and fault indicators GE Mark V Drive Control and Communication Architecture The DS200SDCIG1AFB provides processor-based execution for GE Mark V turbine control drive functions. The board performs signal processing operations, executes stored control firmware, and exchanges data with other Mark V control modules through the rack backplane interface. The board architecture includes EPROM-based firmware storage and RAM memory for runtime calculations. Serial communication channels support diagnostic access and configuration functions through RS-232 and RS-485 interfaces. For GE industrial control platforms, firmware flash and memory compatibility must match the installed Mark V system configuration. Incorrect firmware revision matching can affect board initialization and module communication behavior. Frequently Asked Questions Q: What processor architecture is used on the GE DS200SDCIG1AFB?A: The DS200SDCIG1AFB uses a 16-bit Motorola MC68xxx series processor for drive control execution and signal processing tasks. Q: What power supply rails are required by this control card?A: The board operates from Mark V rack power rails, including +5 VDC logic supply and +/-15 VDC analog supply rails. Q: Can the DS200SDCIG1AFB operate outside a GE Mark V rack system?A: No. The card is designed for integration within GE Mark V Speedtronic control racks and requires compatible backplane communication and firmware configuration. Field Installation Guidelines Install the DS200SDCIG1AFB only in the designated GE Mark V rack slot with the correct mechanical alignment and backplane connection. Before handling the board, apply ESD protection procedures to prevent damage to processor, memory, and communication circuits. Verify that the EPROM firmware version matches the target control system configuration before replacement. Route signal wiring separately from high-current power conductors to reduce electrical interference. Maintain proper cable shielding practices, with shield termination connected according to the site grounding standard. Ensure connectors are fully seated and inspect the card edge contacts for contamination before system startup.
$200.00 $100.00
-
General Electric GE DS200SIOBG1AAA Serial I/O Board
GE DS200SIOBG1AAA Serial I/O Board Configured for field signal acquisition and serial communication in GE Mark V Speedtronic turbine control systems, the GE DS200SIOBG1AAA (DS200SIOB Serial I/O Board) provides direct physical/electrical execution for digital I/O, analog signal conversion, and RS-232/RS-485 data exchange between field devices and control processors. Hardware Specifications Parameter Specification Model DS200SIOBG1AAA Brand GE General Electric Origin United States Weight 0.58 kg Dimensions 250 x 180 x 30 mm Operating Temp -30 to +65 deg C Power Consumption 0.3 A @ 5 VDC logic supply Product Type Serial I/O Board Series Mark V Speedtronic Digital Inputs 16 channels, 24 VDC, 3.3 kOhm input impedance Digital Outputs 8 channels, 24 VDC, 0.5 A maximum Analog Inputs 4 channels, 4-20 mA or 0-10 V Analog Outputs 2 channels, 4-20 mA Serial Communication Ports 2 x RS-232/RS-485 ports Serial Baud Rate 300-38,400 bps Processor 16-bit CPU with ADC/DAC signal processing Memory 128 KB flash configuration memory Isolation Voltage 2500 VAC field-to-logic isolation External Power Supply 24 VDC Indicators 8 LED indicators for power, run, fault, and I/O status Storage Temp -40 to +85 deg C PCB Protection Standard coating, conformal coating optional Compliance UL, CSA certified GE Mark V Industrial Control Interface Characteristics The DS200SIOBG1AAA integrates digital and analog signal handling with serial communication functions within GE Mark V control architectures. The board provides 16 digital inputs, 8 digital outputs, 4 analog inputs, and 2 analog outputs for connection to field sensors, actuators, and auxiliary control circuits. The embedded 16-bit processor performs signal processing through integrated ADC and DAC functions. The dual RS-232/RS-485 interfaces support serial device communication with configurable baud rates, allowing data exchange between connected control components. Profinet / EtherNet/IP Deterministic Networks and I/O Density Scaling As part of the GE Mark V industrial control platform, the DS200SIOBG1AAA follows structured I/O density scaling through combined discrete, analog, and serial interfaces. The board architecture provides centralized field signal collection while maintaining electrical isolation between external wiring and control logic. The 2500 VAC field-to-logic isolation separates external devices from internal processing circuits. Connectorized board integration supports cabinet-based installation and structured signal routing within turbine control systems. Frequently Asked Questions Q: What communication interfaces are available on the DS200SIOBG1AAA?A: The board provides two independent RS-232/RS-485 serial communication ports with configurable baud rates from 300 to 38,400 bps. Q: What types of field signals can the DS200SIOBG1AAA process?A: The board supports 24 VDC digital inputs, 24 VDC digital outputs, 4-20 mA or 0-10 V analog inputs, and 4-20 mA analog outputs. Q: Does the DS200SIOBG1AAA provide electrical isolation?A: Yes. The board provides 2500 VAC field-to-logic isolation between external signal circuits and internal control electronics. Field Installation Guidelines Install the DS200SIOBG1AAA in the designated GE Mark V control cabinet position and verify board orientation before connection. Confirm all field wiring assignments for digital inputs, outputs, and analog channels according to the applicable system drawings. Use shielded cables for low-level analog signals where required. Route communication wiring separately from high-current power cables to reduce electromagnetic interference. Connect cable shields according to the cabinet grounding design. Before board replacement, document existing connector locations and signal assignments. After installation, verify LED status indicators, serial communication parameters, and I/O signal operation through the Mark V diagnostic interface.
$200.00 $100.00
-
General Electric GE DS200TCRAG1ACC Relay Output Board
GE DS200TCRAG1ACC Relay Output Board The GE DS200TCRAG1ACC, also cataloged as the DS200TCRA Relay Output Board, operates as a dedicated hardware component for relay signal switching and field device control within GE Mark V Speedtronic turbine control systems. It provides isolated relay outputs for actuators, solenoids, alarms, and auxiliary equipment interfaces. Hardware Specifications Parameter Specification Model DS200TCRAG1ACC Brand GE General Electric Origin United States Weight 0.85 kg Dimensions 259 x 191 x 30 mm Operating Temp -40 to +65 deg C Power Consumption Not specified Product Type Relay Output Board Series Mark V Speedtronic Functional Acronym TCRA Relay Channels 16-30 relay outputs depending on revision Relay Type SPDT Form C mechanical relays Contact Rating 5 A @ 250 VAC / 30 VDC Isolation Protection 2.5-5 kV RMS Relay Contacts Gold-plated contacts Contact Life 500,000+ operations Response Time <10 ms Indicators LED status indication per relay channel Power Supply 24 V DC relay coil supply; backplane +5 VDC and +/-15 VDC Connectors 4 x 34-pin connectors, 4 x 12-pin connectors, 34-pin terminal block PCB Coating Normal coating Storage Temp -40 to +85 deg C Humidity Range 10-95% non-condensing Compliance UL, CSA, SIL2 GE Mark V Relay Output Switching Characteristics The DS200TCRAG1ACC provides relay-based discrete output switching between Mark V control logic and external field circuits. The board uses isolated mechanical relay channels with gold-plated contacts to control external actuators, alarm circuits, and auxiliary equipment. The relay output architecture supports industrial control applications requiring electrical separation between control electronics and field loads. Channel status LEDs provide local indication of relay activation states for maintenance diagnostics. For GE Mark V system integration, the board operates through backplane communication and connector interfaces associated with Group 1 control assemblies. The DS200TCRAG1ACC supports firmware and hardware compatibility within defined Mark V module configurations. Deterministic Relay Control and I/O Interface The DS200TCRAG1ACC applies relay output switching logic within GE industrial control architectures. The isolated relay channels provide separation between low-level control signals and external electrical loads. The board supports discrete I/O density scaling through multiple relay channels, allowing turbine control systems to manage multiple field devices from a single terminal board assembly. Connectorized field wiring supports structured cabinet installation and signal distribution. Frequently Asked Questions Q: What type of outputs are provided by the DS200TCRAG1ACC?A: The board provides mechanical SPDT Form C relay outputs for switching external field devices such as actuators, solenoids, alarms, and auxiliary equipment. Q: Does the DS200TCRAG1ACC provide electrical isolation between control and field circuits?A: Yes. The relay output channels provide galvanic separation between Mark V control electronics and connected field circuits. Q: What diagnostic functions are available on the relay output board?A: Each relay channel includes an LED indicator for local relay status monitoring during operation and maintenance procedures. Field Installation Guidelines Install the DS200TCRAG1ACC within the designated GE Mark V control cabinet slot and verify connector orientation before insertion. Confirm all relay output wiring assignments against system drawings before energizing external field circuits. Maintain separation between relay output wiring and sensitive analog signal cables to reduce electrical interference. Ground cable shields according to cabinet grounding practices where shielded field wiring is applied. Before replacing the board, record existing connector positions and relay channel assignments. After installation, verify LED status indications and confirm correct field device activation through the Mark V control interface.
$200.00 $100.00
-
General Electric GE DS200QTBAG1ADC Analog I/O Terminal Board
GE DS200QTBAG1ADC Analog I/O Terminal Board The GE DS200QTBAG1ADC, also cataloged as the DS200QTBA Analog I/O Terminal Board, operates as a dedicated hardware component for analog signal termination and conditioning within GE Mark V Speedtronic turbine control systems. It interfaces with LVDT feedback, servo valve outputs, magnetic pulse inputs, and generator power signals through field wiring connections. Hardware Specifications Parameter Specification Model DS200QTBAG1ADC Brand GE Energy Origin United States Weight 0.40 kg Dimensions 25.9 x 16.0 x 6.4 cm Operating Temp -40 to +85 deg C Power Consumption Not specified Product Type Analog I/O Terminal Board Series Mark V Speedtronic / EX2000 Configuration Signal Inputs 6 magnetic pulse frequency inputs, 0-10 kHz LVDT Channels 6 channels with 5 kHz / 10 VAC excitation Servo Outputs 8 channels, 4-20 mA / +/-10 V outputs Resolution 16-bit analog resolution Analog Accuracy +/-0.5% Servo Output Accuracy +/-0.05% Response Time <=5 ms Isolation Voltage 1000 V AC continuous Surge Protection 130 V AC MOV protection per channel Connectors 2 terminal blocks with 72 signals each, 1 x 40-pin JFF connector Communication Interface RS-232 / RS-485 diagnostic port PCB Protection Conformal coating with EMI resistance Hot-Swap Capability Supported Diagnostics LED signal status indicators GE Mark V Analog Signal Interface Characteristics The DS200QTBAG1ADC terminal board provides signal routing and conditioning functions between field devices and GE Mark V control modules. The board processes analog feedback loops including LVDT actuator position signals, servo valve command outputs, turbine speed pulse signals, and generator measurement inputs. The analog channels support 16-bit conversion resolution for turbine control signal processing. LVDT interface circuits provide excitation and feedback demodulation functions for actuator position measurement. Servo output channels support electro-hydraulic valve command transmission with fast signal response characteristics. The board architecture supports deterministic signal handling within Mark V turbine control configurations. Terminal connections provide field wiring termination, while the JFF connector provides internal control system interface connections. Frequently Asked Questions Q: What field signals can the DS200QTBAG1ADC process?A: The board supports LVDT feedback channels, magnetic pulse frequency inputs, servo valve analog outputs, and generator power transmitter signals within Mark V control configurations. Q: Does the DS200QTBAG1ADC support hot swapping?A: The board supports hot-swap capability. Field replacement procedures must follow GE Mark V system maintenance requirements to avoid signal calibration or wiring errors. Q: What type of diagnostic interface is available on this terminal board?A: The board provides LED status indicators and RS-232/RS-485 serial communication connections for diagnostic monitoring. Field Installation Guidelines Install the DS200QTBAG1ADC according to GE Mark V cabinet wiring procedures. Verify terminal block assignments before connecting field devices, especially for LVDT excitation, servo outputs, and pulse input circuits. Use shielded cables for analog signal wiring where required. Connect cable shields according to the cabinet grounding scheme to reduce electromagnetic interference on low-level feedback signals. Separate analog signal cables from high-current power conductors and switching circuits. Confirm connector seating, terminal torque, and board alignment before system energization. During replacement operations, record existing wiring positions and verify signal calibration after installation.
$200.00 $100.00
-
General Electric GE DS200PTBAG1BBA Terminal Board
GE DS200PTBAG1BBA Terminal Board The GE DS200PTBAG1BBA, also cataloged as the DS200PTBA Terminal Board, operates as a dedicated hardware component for field signal termination and protection circuit routing within the GE Mark V Speedtronic turbine control system. The board provides physical wiring interfaces for turbine sensors, actuators, and auxiliary devices connected to processor boards. Hardware Specifications Parameter Specification Model DS200PTBAG1BBA Brand GE Origin USA Weight 0.50 kg Dimensions 280 x 200 x 25 mm Operating Temp -30 deg C to +65 deg C Power Consumption Passive terminal interface board, no dedicated power consumption Board Type Terminal Board Functional Acronym PTBA System Platform GE Mark V Speedtronic Turbine Control System Product Series Mark V Speedtronic Functional Description Protection Termination Module Supported Signals Analog signals and discrete input/output circuits Terminal Interface Multiple screw-type field wiring terminals Isolation Galvanic isolation between field and logic interfaces Mounting Type Panel-mounted in Mark V cabinet Assembly Type Normal Assembly PCB Protection Conformal coating I/O Density Scaling and Protection Signal Routing The DS200PTBAG1BBA provides the termination layer for protection-related field circuits in the GE Mark V architecture. The board organizes external wiring connections from sensors, actuators, and auxiliary devices before signal transfer to control processing modules such as TCRA, TCCB, and TCDA. The PTBA terminal interface supports I/O density scaling by providing structured connection points for multiple turbine control circuits. The passive wiring design maintains signal separation and allows integration with different Mark V processor boards through defined terminal assignments. Frequently Asked Questions Q: Is the DS200PTBAG1BBA a signal processing module?A: No. The PTBA is a passive protection termination module used for field wiring connection and signal routing. Q: What type of field devices can be connected through the terminal board?A: The board supports wiring connections for turbine sensors, actuators, auxiliary devices, and analog/discrete I/O circuits according to the Mark V cabinet configuration. Q: Does the DS200PTBAG1BBA require firmware configuration?A: No. The terminal board does not contain a processor or firmware storage and functions as a hardware termination interface. Field Installation Guidelines Install the DS200PTBAG1BBA at the specified GE Mark V cabinet mounting location and verify terminal identification before connecting field wiring. Confirm screw terminal connections are tightened according to approved cabinet wiring procedures. Route field signal cables separately from high-current power conductors and switching circuits to reduce electromagnetic interference. Use shielded instrumentation wiring where required and connect cable shields according to the cabinet grounding arrangement. Before replacement or maintenance, isolate system power and verify field circuits are de-energized. Confirm terminal assignments, connector references, and revision compatibility before returning the control system to operation.
$200.00 $100.00
-
General Electric GE DS200TBQBG1ACB Terminal Board
GE DS200TBQBG1ACB Terminal Board The GE DS200TBQBG1ACB, also cataloged as the DS200TBQB Terminal Board, operates as a dedicated hardware component for field signal termination and I/O routing within the GE Mark V Speedtronic turbine control system. The board provides physical connection points for analog and discrete signals between field devices and control electronics. Hardware Specifications Parameter Specification Model DS200TBQBG1ACB Brand GE Origin USA Weight 0.48 kg Dimensions 280 x 200 x 25 mm Operating Temp -30 deg C to +65 deg C Power Consumption Passive terminal interface board, no dedicated power consumption Board Type Terminal Board Functional Acronym TBQB System Platform GE Mark V Speedtronic Turbine Control System Product Type Input Termination Module Supported Signals Discrete inputs/outputs and analog signals Terminal Interface Multiple screw-type field wiring terminals Isolation Galvanic isolation between field and logic interfaces Mounting Panel-mounted in Mark V cabinet PCB Protection Conformal coating I/O Density Scaling and Field Signal Routing The DS200TBQBG1ACB provides the field termination layer for GE Mark V turbine control I/O circuits. The terminal board routes analog and discrete signals from external sensors, switches, and actuators to processor interface boards including TCRA and TCCB modules. The board supports I/O density scaling within the Mark V cabinet by organizing multiple field circuits into structured terminal connections. Its passive signal routing design maintains wiring separation and simplifies connection between field devices and control processing hardware. Frequently Asked Questions Q: Is the DS200TBQBG1ACB responsible for signal processing?A: No. The board is a passive terminal interface module used for field wiring termination and signal routing. Q: What types of signals can be connected through the TBQB terminal board?A: The board supports discrete input/output signals and analog field signals according to the Mark V cabinet configuration. Q: Does the terminal board require an external power supply?A: No. The DS200TBQBG1ACB does not contain active processing circuits and does not require an independent power connection. Field Installation Guidelines Install the DS200TBQBG1ACB in the designated Mark V cabinet mounting location and verify terminal identification before field wiring connection. Confirm all screw terminals are properly tightened to maintain stable electrical contact. Route analog signal cables separately from high-current power conductors and switching circuits to minimize electromagnetic interference. Use shielded cables where required, and terminate shields according to the turbine control cabinet grounding practice. Before installation or maintenance, isolate system power and verify field circuits are de-energized. Check terminal assignments, signal polarity, and connection references against the approved Mark V wiring documentation before system startup.
$200.00 $100.00
-
General Electric GE DS200TBCAG1AAA Terminal Board
GE DS200TBCAG1AAA Terminal Board Configured for field signal termination and analog/discrete wiring connection in the GE Mark V Speedtronic turbine control system, the GE DS200TBCAG1AAA (DS200TBCA Terminal Board) provides direct physical/electrical execution for routing field device signals between external wiring and Mark V control modules. Hardware Specifications Parameter Specification Model DS200TBCAG1AAA Brand GE Origin USA Weight 0.45 kg Dimensions 280 x 200 x 25 mm Operating Temp -30 deg C to +65 deg C Power Consumption Passive terminal interface board, no dedicated power consumption Board Type Terminal Board Functional Acronym TBCA System Platform GE Mark V Speedtronic Turbine Control System Mounting Location R5 Core Communication Connector 3PL Input Signal Types 4-20 mA and discrete field signals Output Signal Type 4-20 mA Output Connector JAA Terminal Interface Screw-type field wiring terminals Isolation Galvanic isolation between field and logic interfaces PCB Protection Conformal coating Board Function Field wiring termination and signal routing I/O Density Scaling and Field Signal Integration The DS200TBCAG1AAA provides the physical termination layer between turbine field devices and GE Mark V control electronics. The terminal board supports organized connection of analog and discrete signals from sensors, switches, and actuators to processor interface boards such as TCCA and TCCB. Within the Mark V architecture, the terminal interface supports I/O density scaling by allowing multiple field circuits to be routed through structured terminal points before reaching control processing modules. The board maintains signal separation and wiring organization for analog current loops and discrete control circuits. Frequently Asked Questions Q: Is the DS200TBCAG1AAA an active processing module?A: No. The board is a passive terminal interface component used for field wiring termination and signal routing to Mark V control electronics. Q: What field signal types can be connected through this terminal board?A: The board supports analog 4-20 mA signals and discrete field device connections according to the Mark V cabinet configuration. Q: Does the DS200TBCAG1AAA require a separate power supply connection?A: No. The board functions as a passive wiring interface and does not contain an independent power conversion circuit. Field Installation Guidelines Install the DS200TBCAG1AAA at the specified Mark V cabinet mounting position and verify terminal identification before connecting field wiring. Ensure screw terminals are properly secured to maintain stable electrical contact. Route analog signal cables separately from high-current conductors and switching circuits to reduce electromagnetic interference. Use shielded instrumentation wiring where required, with cable shield termination following the cabinet grounding design. Before servicing or rewiring, remove applicable system power sources and confirm signal isolation. Verify terminal assignments, polarity, and connector references against the approved Mark V wiring documentation before system startup.
$200.00 $100.00
-
General Electric GE DS200SLCCG3AGH LAN Communication Board
GE DS200SLCCG3AGH LAN Communication Board Configured for Ethernet and ARCnet data communication in the GE Mark V Speedtronic turbine control system, the GE DS200SLCCG3AGH (DS200SLCC LAN Communication Board) provides direct physical/electrical execution for controller network interfacing, protocol processing, and diagnostic data exchange between turbine control processors and external systems. Suffix Breakdown & Model Matrix Model Element Description DS200 GE Mark V DS200 hardware series designation SLCC LAN Communication Board functional acronym G3 Board hardware configuration identifier AGH Functional revision and artwork revision designation Functional Revision 1 A Functional Revision 2 G Artwork Revision H Hardware Specifications Parameter Specification Model DS200SLCCG3AGH Brand GE Origin USA Weight 0.55 kg Dimensions 200 x 150 x 25 mm Operating Temp -30 deg C to +65 deg C Power Consumption 24 VDC, 250 mA max Board Type LAN Communication Board Functional Acronym SLCC System Platform GE Mark V Speedtronic Turbine Control System Network Interface 10Base-T Ethernet (RJ45) Additional Network Interface ARCnet communication Supported Protocols TCP/IP, Modbus TCP, GE SRTP, ARCnet Processor 32-bit CPU with integrated Ethernet controller Firmware Memory 512 KB flash SRAM Memory 256 KB Data Retention 0.22 F super capacitor, approx. 72 hours Isolation 1500 V RMS Ethernet-to-backplane isolation Connectors RJ45, 9-pin SUB-D debug port, terminal block Indicators Power, Link, Activity, Fault LEDs PCB Protection Normal coating Deterministic Network Communication The DS200SLCCG3AGH manages communication between Mark V controller cores and plant-level control networks through Ethernet and ARCnet interfaces. The onboard communication processor handles protocol conversion, packet processing, and network diagnostics without direct loading of the turbine control processor. The board supports industrial network integration through TCP/IP, Modbus TCP, and GE SRTP communication methods. Ethernet communication paths provide deterministic data transfer between controller racks, HMI interfaces, and distributed control system connections. Frequently Asked Questions Q: What network interfaces are available on the DS200SLCCG3AGH?A: The board provides a 10Base-T Ethernet RJ45 interface and ARCnet communication capability for Mark V turbine control network connections. Q: What diagnostic information can be monitored from the board?A: Four front-panel LEDs indicate power status, network link condition, communication activity, and fault conditions. Q: Does the board isolate Ethernet signals from the control backplane?A: Yes. The communication interface provides 1500 V RMS isolation between Ethernet circuitry and the Mark V backplane. Field Installation Guidelines Install the DS200SLCCG3AGH in the designated GE Mark V <C> core rack position and verify connector orientation before insertion. Follow approved cabinet procedures for module removal and installation. Use shielded Ethernet cabling where required by the cabinet network design. Route communication cables separately from high-current power wiring and switching circuits to reduce electromagnetic interference. Verify Ethernet connections, terminal wiring, and communication configuration settings before startup. Confirm DIP switch settings, network parameters, and protocol assignments according to the approved Mark V system configuration. After power application, observe the Power, Link, Activity, and Fault LEDs to confirm communication initialization and network status.
$200.00 $100.00
-
General Electric GE DS200TCCBG1BED Common Extended Analog I/O Board
GE DS200TCCBG1BED Common Extended Analog I/O Board The GE DS200TCCBG1BED, also cataloged as the DS200TCCB Common Extended Analog I/O Board, operates as a dedicated hardware component for analog signal acquisition and conversion within the GE Speedtronic Mark V turbine control system. The board processes RTD, thermocouple, transmitter, and voltage input signals through integrated A/D conversion and analog output channels. Hardware Specifications Parameter Specification Model DS200TCCBG1BED Brand GE Origin USA Weight 2.00 lbs Dimensions 230 x 170 x 30 mm Operating Temp 0 deg C to +50 deg C typical; extended tolerance -30 deg C to +65 deg C Power Consumption Approx. 8 W Board Type Common Extended Analog I/O Board Functional Acronym TCCB System Platform GE Speedtronic Mark V Turbine Control System Analog Inputs 8 differential channels Supported Inputs RTD, thermocouple, 4-20 mA, +/-10 V Analog Outputs 4 channels, 0-10 V or 4-20 mA Input Resolution 12-bit A/D conversion Output Resolution 12-bit DAC conversion Input Accuracy +/-0.05% FS Output Accuracy +/-0.1% FS Sampling Rate Approx. 200 Hz per channel Isolation Voltage 1500 V field-to-logic Power Supply 24 VDC +/-10% and +5 VDC logic rail Connectors JCC/JDD RTD inputs, JEE auxiliary, 3PL I/O engine interface Processor Intel 80196 microcontroller Firmware Storage Socketed EPROMs PCB Protection Normal coating PCB Layers 6-layer noise-hardened design I/O Density Scaling and Analog Processing The DS200TCCBG1BED extends the analog processing capacity of the GE Mark V platform through additional RTD, thermocouple, current, and voltage measurement channels. The onboard signal conditioning circuitry performs local conversion of field analog signals before transferring processed data through the control architecture. The board uses GE industrial control I/O density scaling methods to increase sensor channel availability while maintaining compatibility with Mark V control racks. The onboard Intel 80196 microcontroller manages local scanning, conversion handling, and diagnostic processing. Frequently Asked Questions Q: What types of field signals can be connected to the DS200TCCBG1BED analog inputs?A: The board supports differential analog inputs for RTD, thermocouple, 4-20 mA transmitter signals, and +/-10 V voltage inputs. Q: Does the DS200TCCBG1BED provide isolation between field wiring and control electronics?A: Yes. The board provides 1500 V field-to-logic isolation for separation between external analog signals and internal control circuits. Q: Is firmware stored directly on the board hardware?A: Yes. The board uses socketed EPROM devices for firmware storage and calibration data management. Field Installation Guidelines Install the DS200TCCBG1BED in the designated GE Speedtronic Mark V rack location and verify connector identification before applying power. Confirm that JCC, JDD, JEE, and 3PL connections match the approved wiring documentation. Analog signal cables should be routed separately from high-voltage and high-current conductors to reduce electromagnetic interference. Shielded instrumentation cables should be used where required, with cable shields terminated according to the control cabinet grounding design. After installation, verify field input polarity, RTD and thermocouple wiring configuration, and analog channel assignments. Perform the required calibration procedure using the onboard reference points before returning the turbine control system to service.
$200.00 $100.00
-
General Electric DS200TCDAH1BHJE GE Mark V Digital I/O Board
GE DS200TCDAH1BHJE Digital I/O Board Configured for discrete signal acquisition and output execution in the GE Speedtronic Mark V turbine control system, the GE DS200TCDAH1BHJE (DS200TCDA Digital I/O Board) provides direct physical/electrical execution through optically isolated digital input and output channels. The board transfers field contact, trip switch, sensor, and actuator signals through the IONET backplane interface. Hardware Specifications Parameter Specification Model DS200TCDAH1BHJE Brand GE Origin USA Weight 0.8 kg Dimensions 178 x 101 x 30 mm Operating Temp -20 deg C to +60 deg C Power Consumption Powered from 5 VDC, 24 VDC, and 125 VDC system rails Board Type Digital Input/Output Processor Board System Platform GE Speedtronic Mark V Turbine Control System Digital Inputs 16 optically isolated channels Digital Outputs 16 optically isolated channels Isolation Method Optocoupler-based galvanic isolation Communication Interface IONET proprietary backplane communication Connectors Dual 50-pin headers and 2 x 3-pin plugs Configuration 8 jumper blocks (JP1-JP8) Diagnostics 10-LED diagnostic array and CR9 side LED PCB Protection Full conformal coating IONET Backplane and Digital Signal Processing The DS200TCDAH1BHJE integrates GE Mark V digital I/O processing functions through the IONET backplane communication network. The onboard microcontroller performs local I/O scanning and signal handling, reducing direct processing load on the turbine control processor. The board supports deterministic digital data exchange between field devices and the Mark V control core. Input channels accept discrete signals from limit switches and sensors, while output channels provide control signals for relay interfaces, solenoid drivers, and annunciator circuits through compatible relay driver boards. Frequently Asked Questions Q: Does the DS200TCDAH1BHJE provide electrical isolation between field signals and the control system?A: Yes. The board uses optocoupler-based galvanic isolation for its digital input and output channels to separate field wiring from internal control electronics. Q: What communication method is used for data exchange with the Mark V system?A: The board communicates through the proprietary GE IONET backplane interface for digital signal transfer between I/O hardware and the turbine control processor. Q: What diagnostic functions are available on the board?A: The board includes a 10-LED diagnostic array for channel status indication and a CR9 LED for board power and processing activity monitoring. Field Installation Guidelines Install the DS200TCDAH1BHJE in the designated GE Speedtronic Mark V rack position and verify connector alignment before insertion. Ensure that dual 50-pin headers and auxiliary plugs are fully seated to maintain correct field signal routing. Field wiring should be separated from high-current power conductors and high-noise switching circuits. Use appropriate cable shielding practices, with shield termination following the grounding requirements of the turbine control cabinet design. Verify supply rail connections for 5 VDC, 24 VDC, and 125 VDC sources before energizing the module. Maintain clean cabinet conditions to preserve the conformal coating protection and prevent contamination from moisture, dust, or conductive particles. Confirm jumper block settings match the approved control configuration before system operation.
$200.00 $100.00
-
General Electric GE DS200TCDAH1BHE Digital to Analog Converter Board
GE DS200TCDAH1BHE Digital to Analog Converter Board Configured for digital signal conversion in the GE Mark V turbine control system, the GE DS200TCDAH1BHE (DS200TCDA Digital to Analog Converter Board) provides direct electrical conversion from processor-generated digital data to analog output signals for turbine control interfaces. Hardware Specifications Parameter Specification Model DS200TCDAH1BHE Brand GE General Electric Origin United States Weight 0.8 kg Dimensions 233 mm x 160 mm x 25 mm Operating Temp -30 to +65 deg C Power Consumption Supplied through +5 VDC and +/-15 VDC backplane power Product Type Digital I/O Boards Series Mark V Functional Acronym TCDA Input Voltage +5 VDC, +/-15 VDC from backplane Digital Input Interface 16-bit parallel bus from CPCA/SDCC boards Analog Output Range +/-10 VDC, 4-20 mA DAC Resolution 12-bit Isolation Rating 2500 Vrms Response Time < 5 ms signal conversion Diagnostics Front-panel LEDs: Run, Fail, Output Status Redundancy Support Dual/triple modular redundancy compatible Mounting Type Rack mount, single-slot Deterministic Network and I/O Density Characteristics The DS200TCDAH1BHE operates as an analog interface expansion board within the GE Mark V control architecture. The module receives digital control values through the processor board interface and performs digital-to-analog conversion for connected field devices. I/O density scaling is achieved through dedicated conversion channels supporting multiple analog output requirements within the rack system. The board interfaces with CPCA and SDCC processor modules through the Mark V backplane structure. Firmware flash compatibility and processor configuration must match the installed control system revision to maintain correct signal mapping and output execution. Frequently Asked Questions Q: What type of signals does the DS200TCDAH1BHE convert?A: The board converts 16-bit digital control data from processor boards into analog output signals including +/-10 VDC and 4-20 mA. Q: Does the DS200TCDAH1BHE contain independent control processing?A: No. The board performs digital-to-analog conversion functions and relies on connected Mark V processor boards for control logic execution. Q: Which processor boards interface with the TCDA board?A: The module interfaces with CPCA and SDCC processor boards within the GE Mark V control system. Field Installation Guidelines Install the DS200TCDAH1BHE in the designated Mark V rack slot and verify proper backplane connector alignment before energizing the system. Confirm that analog output wiring matches the approved terminal configuration and signal requirements. Route analog signal cables separately from high-power conductors to reduce electrical noise coupling. Cable shielding should be grounded according to the site grounding standard. Verify polarity, terminal tightness, and processor board compatibility before commissioning.
$200.00 $100.00
-
General Electric GE DS200SDCCG5AHD Drive Control Card
GE DS200SDCCG5AHD Drive Control Card The GE DS200SDCCG5AHD, also cataloged as the DS200SDCC Drive Control Card, operates as a dedicated hardware component for executing drive control algorithms and managing processor-based I/O functions within the GE Mark V control system. It provides CPU processing, communication interfaces, and deterministic control execution. Hardware Specifications Parameter Specification Model DS200SDCCG5AHD Brand GE General Electric Origin United States Weight 0.9 kg Dimensions 233 mm x 160 mm x 25 mm Operating Temp -30 to +65 deg C Power Consumption Supplied through +5 VDC and +/-15 VDC backplane power Product Type Drive Control Cards Series Mark V Functional Acronym SDCC Processor Motorola 68020 32-bit CPU Clock Speed 20 MHz Memory 2 MB DRAM, 512 KB SRAM, 1 MB EPROM Non-Volatile Storage EEPROM configuration storage Communication Interfaces VMEbus, RS-232, Ethernet 10 Mbps Isolation Rating 2500 Vrms Response Time < 10 ms control loop execution Diagnostics Front-panel LEDs: Run, Fail, Comm, Watchdog Mounting Type VME rack mount, single-slot Redundancy Support Dual and TMR compatible architecture Deterministic Network and Firmware Interface Characteristics The DS200SDCCG5AHD operates as a processor and communication node within the Mark V control architecture. The board manages backplane bus communication velocity through VMEbus interaction and coordinates data exchange between control logic, connected I/O assemblies, and external communication ports. Firmware flash compatibility and configuration data storage are managed through onboard memory devices including EEPROM and EPROM. Correct firmware matching is required for initialization and communication with the Mark V system. The processor executes control routines with defined timing for turbine and drive control applications. Frequently Asked Questions Q: What processor architecture is used on the DS200SDCCG5AHD?A: The board uses a Motorola 68020 32-bit CPU operating at 20 MHz for control algorithm execution and system processing. Q: Which communication interfaces are available on this control card?A: The DS200SDCCG5AHD provides VMEbus, RS-232, and Ethernet communication interfaces for system integration and diagnostics. Q: Does the SDCC board support redundant control configurations?A: The provided specifications indicate compatibility with dual and triple modular redundancy (TMR) configurations within the Mark V control architecture. Field Installation Guidelines Install the DS200SDCCG5AHD into the assigned Mark V VME rack slot with the correct mechanical alignment. Verify backplane connector engagement before applying system power. Ensure that firmware configuration matches the installed Mark V control system version. Route communication and signal cables separately from high-voltage conductors to reduce electromagnetic interference. Maintain proper grounding practices for rack assemblies and cable shields according to site electrical standards. Confirm airflow paths remain unobstructed to maintain the specified operating temperature range.
$200.00 $100.00
-
General Electric GE DS200TCQCG1BKG Digital I/O Termination Board
GE DS200TCQCG1BKG Digital I/O Termination Board The GE DS200TCQCG1BKG, also cataloged as the DS200TCQC Digital I/O Termination Board, operates as a dedicated hardware component for digital signal termination and field wiring interface within the GE Mark V turbine control system. It provides physical connections for digital input, output, and trip circuit signals between field devices and control processor boards. Hardware Specifications Parameter Specification Model DS200TCQCG1BKG Brand GE General Electric Origin United States Weight 0.8 kg Dimensions 233 mm x 160 mm x 25 mm Operating Temp -30 to +65 deg C Power Consumption Passive termination board; powered through connected control system interfaces Product Type Digital I/O Termination Board Series Mark V Functional Acronym TCQC Signal Types Supported Digital inputs, digital outputs, trip solenoid signals Input Voltage 125 VDC nominal field supply Digital Signal Level 24 VDC Terminal Type Multi-level screw terminals Isolation Rating 2500 Vrms Response Time < 10 ms signal transfer Mounting Type Rack mount, single-slot Diagnostics Passive board monitoring through connected CPCA/LDCC boards Redundancy Supports dual/triple wiring redundancy EtherNet/IP and I/O Density Interface Characteristics The DS200TCQCG1BKG is configured as a passive field termination interface within the Mark V control architecture. The board provides organized signal routing between external digital devices and processor modules without onboard signal execution. Digital I/O density scaling is achieved through the termination arrangement, allowing multiple field circuits to be connected within the rack-based control structure. Signal integrity depends on correct terminal assignment, cable routing, and interface compatibility with connected control boards. Frequently Asked Questions Q: Does the DS200TCQCG1BKG perform signal processing internally?A: No. The board is a passive termination assembly. Signal monitoring and processing are performed by connected Mark V processor and I/O control boards. Q: What field signals can be connected to this termination board?A: The board supports digital input signals, digital output signals, and trip solenoid related circuits using field wiring connections. Q: Is the board compatible with redundant wiring configurations?A: The supplied data indicates support for dual and triple wiring redundancy arrangements within the Mark V control system architecture. Field Installation Guidelines Install the DS200TCQCG1BKG in the designated Mark V rack slot and verify mechanical alignment before securing the board. Field wiring should be terminated according to the approved terminal assignment documentation. Maintain separation between low-level signal wiring and high-energy conductors to reduce electrical interference. Cable shields should be connected according to the system grounding standard, with attention to avoiding ground loops. Verify terminal tightness, insulation condition, and polarity before energizing the control system. Confirm compatibility with connected CPCA, LDCC, and related Mark V control modules before operation.
$200.00 $100.00
You have seen 360 out of 1313 products