تقدم ABB حلول أتمتة صناعية شاملة لمحركات الأقراص وأنظمة التحكم والروبوتات. يضمن مخزوننا العالمي وصولاً سريعاً إلى قطع الغيار النادرة. قلل من وقت التوقف عن العمل وحافظ على استمرارية الإنتاج باستخدام مكونات ABB المعتمدة.
شركة أي بي بي
-
ABB AI880A 3BSE039293R1 High Integrity ABB S800 I/O Analog Input Module
ABB AI880A 3BSE039293R1 High Integrity Analog Input Module Configured for 4-20 mA and 0-20 mA signal acquisition in ABB System 800xA S800 I/O networks, the ABB AI880A 3BSE039293R1 (AI880A High Integrity Analog Input Module) provides direct physical and electrical conversion of field analog signals into controller data. Hardware Specifications Parameter Specification Model AI880A 3BSE039293R1 Brand ABB Product Type High Integrity Analog Input Module Origin Sweden Weight 0.15 kg Dimensions 4.5 x 11 x 11.8 cm (shipping size) Operating Temp 0 to +55 deg C Storage Temp -40 to +70 deg C Power Consumption Not specified in provided data Signal Specification 0-20 mA, 4-20 mA Number of Channels 8 Signal Type Unipolar single ended Resolution 12 bit Input Impedance 250 Ohm with shunt stick TY801 Maximum Input Voltage 11 VDC non destructive NMRR > 40 dB at 50 Hz and 60 Hz Rated Insulation Voltage 50 V Dielectric Test Voltage 500 VAC HART Communication Supported Compatible MTU TU834, TU844, TU845, TU854 ABB S800 I/O Backplane and I/O Density Characteristics The AI880A operates as an ABB S800 I/O analog acquisition component with eight input channels for current-based field signals. The module communicates through the S800 I/O architecture and supports integration with ABB System 800xA control environments. The module uses channel-level signal processing for 0-20 mA and 4-20 mA inputs. Furthermore, the 12 bit conversion resolution provides digital representation of measured process values for controller execution. The ABB I/O platform supports backplane bus communication and I/O density scaling through modular S800 configurations. The AI880A installation requires compatible Module Termination Units, including TU834, TU844, TU845, and TU854, to complete field wiring connections. Frequently Asked Questions Q: What input signals does the AI880A 3BSE039293R1 accept?A: The AI880A accepts unipolar single ended analog current inputs with 0-20 mA and 4-20 mA signal ranges. Q: How many analog input channels are available on the AI880A module?A: The AI880A provides eight analog input channels with 12 bit signal resolution. Q: Which termination units are compatible with the AI880A?A: The module supports TU834, TU844, TU845, and TU854 Module Termination Units for field signal connection. Field Installation Guidelines Install the AI880A module according to ABB S800 I/O mechanical configuration requirements. Verify that the selected Module Termination Unit matches the installed hardware arrangement before connecting field wiring. Use appropriate shielded signal cables for analog current loops. Connect cable shields according to site grounding practices to reduce electromagnetic interference. Separate low-level analog signal wiring from high-voltage power conductors to minimize coupling noise. Confirm current loop polarity before commissioning. Check that field transmitters provide signals within the specified input range of 0-20 mA or 4-20 mA before enabling process measurement functions.
$199.00 $99.00
-
ABB AI893 3BSC690141R1 ABB Advant AC800F-Freelance Analog Input Module
ABB AI893 3BSC690141R1 Analog Input Module The ABB AI893 3BSC690141R1, also cataloged as the AI893 Analog Input Module, operates as a dedicated hardware component for RTD and thermocouple signal acquisition within ABB S800 I/O systems. The module provides 8 input channels with intrinsic safety interface support for temperature measurement applications. Hardware Specifications Parameter Specification Model AI893 3BSC690141R1 Brand ABB Product Type Analog Input Module Origin Sweden Weight 0.2 kg Dimensions 4.4 x 12.1 x 10.8 cm Operating Temp 0 to +55 deg C Storage Temp -40 to +70 deg C Power Consumption Not specified Input Type RTD or TC Number of Channels 8 Resolution 15 bit + sign Input Impedance >10 Mohm Common Mode Voltage Input +/- 5 V CMRR at 50 Hz, 60 Hz >100 dB NMRR at 50 Hz, 60 Hz >80 dB Signal Interface Intrinsic safety interface Product Function Temperature signal input processing ABB S800 I/O Backplane Integration and Signal Processing The AI893 module connects to ABB S800 I/O architecture through the standard I/O communication structure and processes field temperature signals from RTD and thermocouple sensors. In addition, the module supports I/O density scaling with 8 measurement channels in a compact hardware format. The module performs analog signal conversion using 15 bit plus sign resolution. Furthermore, the input stage provides high impedance measurement characteristics and noise rejection performance through common mode and normal mode rejection specifications. ABB industrial control modules use defined backplane bus communication methods for deterministic data exchange between I/O hardware and controller platforms. The AI893 supports temperature measurement configurations where signal integrity, channel separation, and correct sensor wiring are required. Frequently Asked Questions Q: What sensor types can the ABB AI893 3BSC690141R1 accept?A: The AI893 accepts RTD and thermocouple (TC) input signals through its 8 analog input channels with intrinsic safety interface support. Q: What is the resolution of the AI893 analog measurement input?A: The module provides 15 bit plus sign resolution for analog temperature signal conversion. Q: Does the AI893 support intrinsic safety field connections?A: Yes. The module includes an intrinsic safety interface for compatible field measurement applications. Field Installation Guidelines Install the AI893 module according to ABB S800 I/O system installation procedures and verify the correct module position before power application. Connect RTD and thermocouple field wiring using suitable industrial instrumentation cables. Maintain proper cable routing separation between analog signal lines and high-voltage power conductors to reduce electrical interference. For thermocouple applications, verify correct polarity and compensation requirements before commissioning. Ensure shielding practices follow the plant grounding standard and avoid multiple grounding points that may introduce measurement noise. Check terminal connections, module addressing, and controller configuration before placing the analog input channel into service.
$199.00 $99.00
-
ABB DI801 3BSE020508R1 ABB S800 I/O Digital Input Module
ABB DI801 Digital Input Module The ABB DI801 3BSE020508R1, also cataloged as the DI801 Digital Input Module, provides 24 VDC field signal acquisition for S800 I/O systems. The module executes direct electrical input processing through 16 isolated digital channels with channel status indication, filtering selection, and process voltage supervision capability. Hardware Specifications Parameter Specification Model DI801 3BSE020508R1 Brand ABB Origin Sweden Product Type Digital Input Module System Platform ABB S800 I/O Signal Specification 24 VDC Number of Channels 16 digital inputs Signal Type Current sinking Input Voltage Range "0": -30 to +5 V; "1": 15 to 30 V Input Current 6 mA at 24 VDC Input Impedance 3.5 kOhm Isolation Groupwise isolated from ground HART Support No SOE Support No Redundancy No High Integrity No Intrinsic Safety No Filter Times 2 ms, 4 ms, 8 ms, 16 ms selectable Maximum Field Cable Length 600 m Rated Insulation Voltage 50 V Dielectric Test Voltage 500 V Power Dissipation Typical 2.2 W Modulebus +5 V Current Consumption 70 mA Modulebus +24 V Current Consumption 0 Weight 0.24 kg Dimensions 86.1 mm W x 58.5 mm D x 110 mm H Operating Temp 0 to +55 deg C Storage Temp -40 to +70 deg C Protection Class IP20 according to IEC 60529 ABB S800 I/O Backplane and I/O Density Characteristics The DI801 operates within the ABB S800 I/O architecture and provides direct digital signal processing through the ModuleBus interface. The module supports I/O density scaling with sixteen input channels integrated into one compact S800L mechanical design. Each input channel contains current limiting components, EMC protection circuits, LED status indication, and an optical isolation barrier. Therefore, the module separates field signal conditions from internal electronics while maintaining channel-level diagnostic visibility. The DI801 supports ABB S800 I/O backplane communication functions and maintains compatibility with standard S800 system configurations. Channel 16 can additionally monitor process voltage conditions for group supervision functions. Frequently Asked Questions Q: Does the DI801 support redundant input operation?A: No. The DI801 is specified as a non-redundant digital input module and provides one isolated group containing sixteen input channels. Q: What diagnostic indications are available on the DI801 front panel?A: The module provides an S status LED for run or fault indication and individual channel LEDs for input states from channel 1 to channel 16. Q: Can the DI801 monitor external process voltage conditions?A: Yes. Channel 16 can be configured as a process voltage supervision input for the input group. Field Installation Guidelines Install the DI801 module in an ABB S800 I/O station according to the approved mechanical arrangement. Verify that the module keying, connector alignment, and mounting position match the configured system design. Connect field wiring according to the specified wire size range. Maintain proper separation between signal wiring and high-voltage conductors to reduce electromagnetic interference. Use appropriate grounding practices for cabinet installation. Confirm that field cable shielding, EMC protection, and protective earth connections follow the site electrical installation standard. Before commissioning, verify input polarity, 24 VDC field supply levels, channel LED operation, and process voltage supervision status through the control system diagnostics.
$199.00 $99.00
-
ABB TU847Z ABB S800 I/O Module Termination Unit
ABB TU847 Module Termination Unit The ABB TU847 3BSE022462R1, also cataloged as the TU847 Module Termination Unit, provides physical and electrical connection management for redundant CI840/CI840A field communication interface configurations within ABB System 800xA ModuleBus networks. Hardware Specifications Parameter Specification Model TU847 3BSE022462R1 Brand ABB Product Type Module Termination Units Origin Sweden Weight 0.5 kg (1.1 lbs) Dimensions Width 124 mm, Height 186 mm including latch, Depth 47 mm Operating Temp 0 to +55 deg C (approved range +5 to +55 deg C) Power Consumption 24 VDC input, ModuleBus distribution maximum 5 V 1.5 A and 24 V 1.5 A Communication Protocol PROFIBUS DP-V1 Configuration Type Redundant CI840/CI840A, Single I/O Module Redundancy Yes Hot Swap Support No Power Input 24 VDC (19.2 to 30 V) Mounting Orientation Vertical or Horizontal Connector Interface PROFIBUS DSUB9 connector, Service ports RJ45 connector Mechanical Key Configuration 36 different combinations Rated Insulation Voltage 50 V Dielectric Test Voltage 500 VAC Protection Class IP20 according to IEC 529 Relative Humidity 5 to 95 %, non-condensing Storage Temperature -40 to +70 deg C Equipment Class Class I according to IEC 60536, earth protected Certifications CE, EN 61010-1, UL 61010-1, EN 61010-2-201, UL 61010-2-201 Hazardous Location Approval cULus Hazardous Location Class 1 Zone 2, ATEX Zone 2 Marine Certificates ABS, BV, DNV-GL, LR ABB ModuleBus Redundant Communication Interface The TU847 uses ABB ModuleBus architecture to connect two CI840/CI840A communication interface modules in a redundant arrangement. The unit provides dual module positions, dual rotary switches for station address settings from 0 to 99, and electrical ModuleBus connections for distributed I/O communication. The mechanical key system prevents incorrect module installation. Each position uses two six-position keys, creating 36 configuration combinations for module identification control. The TU847 supports connection of a ModuleBus Optical Port TB842 through the TB806 adapter. Therefore, optical ModuleBus extension capability can be integrated into the same hardware configuration. Backplane Bus Communication and I/O Density Scaling The TU847 operates as a passive connection unit within ABB industrial control platforms. It maintains electrical routing between CI840/CI840A interfaces and the ModuleBus network while supporting redundant communication paths. The unit applies ABB backplane bus communication architecture for I/O density scaling across System 800xA installations. Additionally, the fixed ModuleBus current distribution limits define the available power capacity for connected communication modules. Frequently Asked Questions Q: Does the TU847 support hot swap replacement during system operation?A: No. The TU847 cannot be replaced with power applied. The system power must be removed before mechanical replacement. Q: Can the TU847 operate with redundant CI840 and CI840A modules?A: Yes. The TU847 is designed for redundant CI840/CI840A communication interface configurations with two module positions. Q: What installation clearance is required for TU847 removal?A: The TU847 requires available space on the left side to allow removal from the mounting arrangement. Field Installation Guidelines Install the TU847 in a vertical or horizontal mounting position according to cabinet layout requirements. Verify that power is disconnected before removing or replacing the unit. Confirm mechanical key positions before inserting CI840/CI840A modules. Route PROFIBUS cables separately from high-voltage power conductors to reduce electrical interference. Use approved wire sizes from 0.25 to 2.5 mm2 with recommended terminal torque of 0.5 to 0.6 Nm. Maintain proper protective earth connection according to the equipment Class I installation requirements. Check ModuleBus connections and station address settings before commissioning. Ensure environmental conditions remain within the specified operating temperature and humidity limits.
$199.00 $99.00
-
ABB Redundant Module Termination Unit ABB S800 I/O Module TU844 3BSE021445R1
ABB TU844 3BSE021445R1 Redundant Module Termination Unit The ABB TU844 3BSE021445R1, also cataloged as the TU844 Redundant Module Termination Unit, provides physical signal termination and ModuleBus distribution for ABB S800 I/O modules including AI845, AI880, AI880A, and DP840 configurations. Hardware Specifications Parameter Specification Model TU844 3BSE021445R1 Brand ABB Product Type Redundant Module Termination Unit (MTU) Origin Sweden Weight 0.6 kg (1.3 lbs) Dimensions Width: 131 mm including connector; Depth: 64 mm including terminals; Height: 186.5 mm including locking device Operating Temp 0 to +55 deg C (+32 to +131 deg F) Power Consumption Passive MTU design; power consumption generated by connected I/O modules Configuration Type Redundant Connection Type Terminal block I/O Channels 8 Process Voltage Connections 2 + 2 process voltage connections Maximum Voltage Rating 50 V per channel Maximum Current Rating 2 A per I/O channel Maximum Process Connection Current 5 A Compatible I/O Modules AI845, AI880, AI880A, DP840 Mounting Method Horizontal DIN rail mounting ModuleBus Distribution Dual ModuleBus distribution to I/O module and next MTU Input Selection Voltage or current input selection through TY801 shunt sticks Dielectric Test Voltage 500 V AC Wire Size Solid: 0.2 - 4 mm2; Stranded: 0.2 - 2.5 mm2, 24 - 12 AWG Recommended Terminal Torque 0.5 - 0.6 Nm Wire Stripping Length 7 mm Protection Class IP20 according to IEC 60529 Relative Humidity 5 to 95 %, non-condensing Storage Temperature -40 to +70 deg C (-40 to +158 deg F) Pollution Degree Degree 2, IEC 60664-1 Corrosion Protection ISA-S71.04 G3 EMC Compliance EN 61000-6-4, EN 61000-6-2 Electrical Safety Standards EN 61010-1, UL 61010-1, EN 61010-2-201, UL 61010-2-201 Hazardous Location Certification C1 Div 2 cULus, C1 Zone 2 cULus, ATEX Zone 2 Marine Certification ABS, BV, DNV-GL, LR RoHS Compliance EN 50581:2012 WEEE Compliance Directive 2012/19/EU ABB S800 I/O ModuleBus Signal Distribution The TU844 provides electrical termination and routing functions for redundant ABB S800 I/O installations. It distributes two ModuleBuses, with one bus assigned to each I/O module and the outgoing connection extended to the next MTU. The unit generates module addressing by shifting outgoing position signals through the MTU chain. Therefore, connected I/O modules receive the correct hardware position information without additional software configuration. The TU844 supports eight I/O channels, where each channel contains two I/O terminals and one ZP connection. Additionally, TY801 individual shunt sticks define the input mode between voltage and current signals. The channel design supports a maximum rated voltage of 50 V and a maximum rated current of 2 A. The mechanical key system configures compatibility between the MTU and installed I/O modules. Each I/O module position uses two mechanical keys, and each key provides six positions. Therefore, the configuration system supports 36 possible mechanical combinations without changing electrical functionality. Frequently Asked Questions Q: What I/O modules can be connected to the ABB TU844 3BSE021445R1? A: The TU844 supports ABB S800 I/O modules including AI845, AI880, AI880A, and DP840 modules in redundant configurations. Q: How does the TU844 select voltage or current input signals? A: The input selection is performed through individual TY801 shunt sticks. The shunt stick defines whether the channel operates with voltage or current input signals. Q: Can the TU844 be installed on a standard DIN rail? A: Yes. The TU844 uses horizontal DIN rail mounting and includes a mechanical latch that locks the MTU to the rail. Field Installation Guidelines Install the TU844 on a standard DIN rail with the locking mechanism fully engaged before wiring. Verify that the mechanical key positions match the installed ABB S800 I/O module type before commissioning. Use approved terminal wiring methods and maintain correct conductor preparation according to the specified wire range. Separate signal wiring from high-current power cables to reduce electrical interference. Connect cable shields according to the plant grounding standard when shielded instrumentation wiring is used. Confirm TY801 shunt stick positions before applying field signals to prevent incorrect voltage or current input configuration. Inspect ModuleBus connections between adjacent MTUs before system power-up. Maintain environmental limits for temperature, humidity, pollution degree, and enclosure protection during installation.
$199.00 $99.00
-
ABB Module Termination Unit ABB S800 I/O Module TU849 3BSE042560R1
ABB TU849 3BSE042560R1 Module Termination Unit The ABB TU849 3BSE042560R1, also cataloged as the TU849 Module Termination Unit, provides physical termination and power distribution for redundant TB840/TB840A Optical ModuleBus Modem configurations within ABB ModuleBus networks. Hardware Specifications Parameter Specification Model TU849 3BSE042560R1 Brand ABB Origin Sweden Product Type Module Termination Unit (MTU) Communication Protocol ModuleBus Configuration Type Redundant TB840/TB840A, Single I/O, Dual Power Power Input 24 VDC (19.2 to 30 V) Weight 0.45 kg Dimensions 124 mm W x 186.5 mm H x 47 mm D Mounting Vertical or Horizontal DIN rail mounting Operating Temp 0 to +55 deg C (approved range +5 to +55 deg C) Storage Temperature -40 to +70 deg C Power Consumption 2.5 W ModuleBus Current Distribution Maximum 5 V 1.5 A and 24 V 1.5 A Line Redundancy Yes Hot Swap Support No Mechanical Key Configurations 36 selectable combinations Rated Insulation Voltage 50 V Dielectric Test Voltage 500 VAC Protection Class IP20 according to IEC 60529 Relative Humidity 5 to 95 %, non-condensing Wire Size Range Solid and stranded 0.2 to 2.5 mm2, 24 to 12 AWG Recommended Terminal Torque 0.5 Nm ABB ModuleBus Redundant Power and I/O Interface Design The TU849 uses passive electrical routing to connect two TB840/TB840A Optical ModuleBus Modems with individual power supply inputs. The unit provides one electrical ModuleBus connection and supports redundant modem installation for non-redundant I/O configurations. Furthermore, the MTU integrates a rotary switch for cluster address selection from 1 to 7. Four mechanical keys define module compatibility through 36 selectable hardware configurations. The key positions can be adjusted with a screwdriver to match the installed modem arrangement. For ABB industrial control platforms, the TU849 supports ModuleBus communication structures where backplane bus communication velocity and I/O density scaling depend on the connected controller and I/O architecture. The passive termination design maintains direct signal routing without internal processing functions. Frequently Asked Questions Q: Does the ABB TU849 support hot swap replacement of TB840/TB840A modules?A: No. The TU849 does not provide hot swap capability. Power isolation and system shutdown procedures should be followed before replacing connected modem modules. Q: What type of power connection does the TU849 provide for redundant modem installation?A: The TU849 provides two separate power supply connections, with one connection assigned to each TB840/TB840A modem position. Q: How are module compatibility settings configured on the TU849?A: The MTU uses four mechanical keys with six positions each. These settings provide 36 possible hardware configurations and can be adjusted using a screwdriver. Field Installation Guidelines Install the TU849 on a standard DIN rail using the integrated mechanical latch. Verify that the latch is correctly locked after mounting to prevent mechanical movement during operation. Connect the 24 VDC power supply lines according to the assigned modem positions. Maintain correct polarity and separate power routing for each redundant modem connection. Use approved industrial wiring practices when connecting ModuleBus and power conductors. Keep signal cables separated from high-voltage switching circuits to reduce electrical interference. Before operation, verify the rotary switch cluster address setting and confirm that the mechanical key configuration matches the installed TB840/TB840A modem type.
$199.00 $99.00
-
ABB TU847 3BSE022462R1 ABB S800 I/O Module Termination Unit
ABB TU847 3BSE022462R1 Module Termination Unit Configured for CI840 module termination and non-redundant I/O support in ABB System 800xA control networks, the ABB 3BSE022462R1 (TU847 Module Termination Unit) provides direct physical connection between CI840 communication interfaces and connected I/O modules. Hardware Specifications Parameter Specification Model TU847 3BSE022462R1 Brand ABB Origin Sweden Weight 0.5 kg Dimensions 47 mm depth x 186 mm height x 124 mm width Operating Temp Not specified by manufacturer Power Consumption Passive termination unit; power consumption not specified Product Type Module Termination Unit Compatible Module CI840 communication interface Mounting Type Vertical module mounting I/O Configuration Supports non-redundant I/O Redundancy Configuration 1+1 CI840 configuration support Included Components 1 pcs Power Supply Connector, 1 pcs TB807 Modulebus Terminator Protection Compliance RoHS according to EU Directive 2011/65/EU WEEE Category Small Equipment, no external dimension more than 50 cm Customs Tariff Number 85371098 ABB Industrial Control Bus Integration The TU847 3BSE022462R1 operates as a passive interface component within ABB System 800xA S800 I/O configurations. Therefore, it provides mechanical termination, power connection routing, and Modulebus termination functions for CI840 communication modules. The unit supports ABB backplane bus communication structures where module positioning, connector alignment, and termination integrity affect I/O communication stability. Additionally, the included TB807 Modulebus Terminator completes the Modulebus connection path for non-redundant I/O installations. The TU847 design follows ABB S800 I/O hardware architecture principles, allowing vertical installation of associated modules while maintaining the required electrical interface between the communication module and field I/O assemblies. Frequently Asked Questions Q: What ABB module is the TU847 3BSE022462R1 designed to support?A: The TU847 is designed for CI840 communication interface installations and supports 1+1 CI840 configurations with non-redundant I/O operation. Q: Does the TU847 include termination accessories?A: Yes. The unit includes one Power Supply Connector and one TB807 Modulebus Terminator as specified in the product documentation. Q: Is the TU847 a powered electronic I/O module?A: No. The TU847 is a Module Termination Unit that provides physical termination and connection functions rather than performing signal processing. Field Installation Guidelines Install the TU847 in the specified vertical mounting orientation within the ABB S800 I/O assembly. Verify that the CI840 interface module is correctly seated before applying system power. Confirm that the Power Supply Connector is properly installed and mechanically secured. Install the TB807 Modulebus Terminator according to the Modulebus termination requirements. Maintain separation between communication wiring and high-voltage power cables to reduce electrical interference. Connect grounding and shielding according to the control cabinet design and ABB installation requirements. Inspect connectors for contamination, mechanical damage, or improper engagement before commissioning.
$199.00 $99.00
-
ABB TU890 3BSC690075R1 ABB S800 I/O Compact Terminal Block
ABB TU890 3BSC690075R1 Compact Terminal Block Configured for field signal termination and process power connection in ABB S800 I/O systems, the ABB TU890 3BSC690075R1 (TU890 Compact Terminal Block) provides direct physical electrical connection between I/O modules and external field wiring. Hardware Specifications Parameter Specification Model TU890 3BSC690075R1 Brand ABB Product Type Compact Terminal Block Origin Sweden Weight 0.22 kg Dimensions 21 x 6.5 x 8.8 cm Operating Temp 55 deg C Power Consumption Passive terminal connection, no external power consumption Type Compact Connection Terminal block Channels 8 Voltage 24 V Mounting Horizontal DIN rail mounting Process Connections 27 blue terminals Compatible I/O Modules AI890, AI893, AI895, AO890, AO895, DI890, DO890 Mounting Detail 55 deg mounting orientation ABB S800 I/O Terminal Interface and I/O Density Scaling The TU890 provides field wiring termination for ABB S800 I/O modules. It connects process signals, module power interfaces, and ModuleBus-related connections through a compact terminal structure. Furthermore, the terminal block supports I/O density scaling by allowing compact installation arrangements with compatible AI, AO, DI, and DO modules. The mechanical keying design prevents incorrect module insertion, while the DIN rail latching mechanism maintains fixed positioning during operation. The ABB S800 architecture uses structured backplane and ModuleBus communication paths. Therefore, correct terminal assignment and module compatibility verification are required before installation. Frequently Asked Questions Q: Which ABB I/O modules are compatible with the TU890 3BSC690075R1?A: The TU890 is specified for use with ABB AI890, AI893, AI895, AO890, AO895, DI890, and DO890 I/O modules. Q: Does the TU890 require an external power supply?A: No. The TU890 is a passive terminal block and does not require an independent power input. Q: What mounting method does the TU890 use?A: The TU890 uses horizontal DIN rail mounting with an integrated latching device for mechanical retention. Field Installation Guidelines Install the TU890 on a correctly positioned DIN rail according to the cabinet mechanical layout. Verify terminal assignments before connecting field wiring to avoid incorrect signal routing. Keep field signal cables separated from high-current power conductors to reduce electrical interference. Connect cable shields according to the control cabinet grounding design and applicable site standards. Confirm that the installed I/O module type matches the terminal block compatibility list before energizing the system.
$199.00 $99.00
-
ABB ABB TB820V2 3BSE013208R1 Modulebus Optical Modem
ABB TB820V2 3BSE013208R1 Modulebus Optical Modem Configured for optical Modulebus communication extension in ABB S800 I/O systems, the ABB TB820V2 3BSE013208R1 (TB820V2 Modulebus Optical Modem) provides direct physical data transmission between Modulebus segments through optical interfaces. Hardware Specifications Parameter Specification Model TB820V2 3BSE013208R1 Brand ABB Product Type Modulebus Optical Modem Origin Sweden Weight 0.34 kg Dimensions 17 x 5.8 x 12 cm Communication Interface Modulebus optical interface Application Platform ABB S800 I/O system Function Optical Modulebus segment extension and adapter module Backplane Bus Communication and I/O Network Integration The TB820V2 operates as an optical communication interface within ABB industrial control architectures. Therefore, it transfers Modulebus communication signals through optical media to extend physical separation between connected I/O clusters. The unit supports ABB Modulebus network configurations where optical transmission is required. In addition, the optical interface reduces electrical coupling between separated hardware sections and supports distributed I/O installation layouts. The TB820V2 belongs to ABB industrial control hardware designed around backplane bus communication velocity management and I/O density scaling. It integrates with ABB S800 I/O components through the defined Modulebus architecture without providing independent control processing functions. Frequently Asked Questions Q: What is the primary function of the ABB TB820V2 3BSE013208R1?A: The TB820V2 functions as a Modulebus Optical Modem that converts and transfers Modulebus communication signals through optical media between compatible ABB system sections. Q: Does the TB820V2 operate as a standalone controller module?A: No. The TB820V2 is a communication interface component and does not execute user application logic or control algorithms. Q: What system platform uses the TB820V2 Modulebus Optical Modem?A: The TB820V2 is designed for ABB S800 I/O system configurations requiring optical Modulebus communication extension. Field Installation Guidelines Install the TB820V2 according to ABB S800 I/O system hardware configuration requirements. Verify optical cable compatibility before connecting the Modulebus optical interface. Route optical communication cables separately from high voltage power wiring to minimize installation interference. Ensure all mounting connections maintain proper mechanical fixation inside the control cabinet. Confirm system power isolation before removing or installing the module. Check connector alignment before applying system power after installation.
$199.00 $99.00
-
ABB ABB TB805 3BSE008534R1 Modulebus Extension Cable Adaptor
ABB TB805 3BSE008534R1 Modulebus Extension Cable Adaptor Configured for Modulebus extension cable connection in ABB System 800xA and S800 I/O networks, the ABB TB805 3BSE008534R1 (TB805 Modulebus extension cable adaptor) provides direct physical interface conversion through a D-sub 25 female connector for TK801 extension cables. Hardware Specifications Parameter Specification Model TB805 3BSE008534R1 Brand ABB Product Type Modulebus Extension Cable Adaptor Origin Not specified in provided data Weight 0.046 kg Dimensions 25 mm depth x 109 mm height x 22 mm width Operating Temp Not specified in provided data Power Consumption Passive component, no external power consumption Connector Type D-sub 25 female Compatible Cable TK801 Modulebus extension cable Product Function Modulebus outlet and extension cable interface adapter Product Category Module_Termination_Unit RoHS Status Following EU Directive 2011/65/EU WEEE Category 5. Small Equipment (No External Dimension More Than 50 cm) Backplane Bus and Industrial Network Interface The ABB TB805 belongs to the ABB S800 I/O Modulebus accessory family and provides a physical connection point for extending Modulebus communication paths. Therefore, the adaptor maintains the required mechanical alignment between the controller-side interface and external TK801 extension cables. The TB805 uses a passive signal routing structure without internal processing firmware. Consequently, it does not modify communication data or require configuration parameters. The component supports ABB industrial control architectures where I/O density scaling and backplane bus communication velocity management are handled by the active controller and I/O modules. The D-sub 25 female interface provides a defined electrical connection point. Additionally, correct cable shielding and grounding practices help maintain signal integrity in industrial environments. Frequently Asked Questions Q: Does the TB805 require an external power supply?A: No. The TB805 is a passive Modulebus extension cable adaptor and does not require external power input. Q: What cable connects to the TB805 interface?A: The TB805 is designed for use with the ABB TK801 Modulebus extension cable through its D-sub 25 female connector interface. Q: Does the TB805 contain firmware or communication configuration settings?A: No. The TB805 is a hardware adaptor without firmware functions or user-configurable parameters. Field Installation Guidelines Install the TB805 according to ABB S800 I/O system installation procedures. Verify that the D-sub 25 connector is fully seated and mechanically secured before system operation. Route the TK801 extension cable separately from high-voltage power wiring and high-current switching conductors. Maintain proper cable bending radius and avoid excessive mechanical stress on the connector assembly. Connect cable shielding according to the system grounding design. Confirm that all Modulebus extension connections are correctly installed before applying power to the associated ABB control system.
$199.00 $99.00
-
ABB ABB TB806 3BSE008536R1 ModuleBus Extension Cable Adaptor
ABB TB806 3BSE008536R1 ModuleBus Extension Cable Adaptor Configured for ModuleBus signal extension connection in ABB S800 I/O systems, the ABB TB806 3BSE008536R1 (TB806 ModuleBus Extension Cable Adaptor) provides direct physical interface adaptation between ModuleBus segments through a D-SUB 25 male connector. Hardware Specifications Parameter Specification Model TB806 3BSE008536R1 Brand ABB Product Type ModuleBus Extension Cable Adaptor Origin Sweden Weight 0.1 kg Dimensions 12.7 x 5.1 x 5.1 cm Operating Temp 0 to +55 deg C Storage Temperature -25 to +70 deg C Humidity Range RH 5 to 95 % Power Consumption Passive interface component, no external power supply required Mechanics S800 Connector Type D-SUB 25 male Tariff Code 8537101190 Hazardous Location C1 Div 2 cULus, C1 Zone 2 cULus, ATEX Zone 2 Marine Certification ABS, BV, DNV, LR Pollution Degree Degree 2, IEC 60664-1 Corrosion Protection ISA-S71.04: G3 ABB S800 ModuleBus Interface Characteristics The TB806 operates as a passive ModuleBus interface adapter within ABB S800 I/O configurations. Therefore, it supports physical connection extension between compatible ModuleBus components while maintaining the electrical characteristics of the communication path. In addition, ABB S800 architecture depends on defined backplane and ModuleBus communication structures. The TB806 provides the required connector conversion function without adding firmware processing or active communication control. Furthermore, the adaptor supports industrial installation requirements with specified hazardous location approvals and environmental protection classifications. The unit maintains compatibility with ABB ModuleBus extension arrangements where D-SUB 25 male interfaces are required. Frequently Asked Questions Q: Does the ABB TB806 3BSE008536R1 require an external power supply?A: No. The TB806 is a passive ModuleBus extension cable adaptor and does not require an independent power input. Q: What connector interface does the TB806 provide?A: The TB806 provides a D-SUB 25 male connector interface for ModuleBus extension connection within ABB S800 configurations. Q: Can the TB806 be installed in hazardous areas?A: Yes. The listed certifications include C1 Div 2 cULus, C1 Zone 2 cULus, and ATEX Zone 2 approval classifications. Field Installation Guidelines Install the TB806 according to ABB S800 ModuleBus system documentation and approved wiring practices. Verify connector orientation before inserting the D-SUB interface to prevent mechanical damage. Maintain proper cable routing and separate ModuleBus wiring from high-voltage power conductors. Use appropriate shielding and grounding methods according to the installation environment. Confirm environmental conditions remain within the specified operating temperature and humidity limits. Inspect connectors for contamination, corrosion, or mechanical stress before system commissioning.
$199.00 $99.00
-
ABB TB850 3BSC950193R1 ABB S800 I/O CEX-Bus Terminator
ABB TB850 3BSC950193R1 CEX-Bus Terminator The ABB TB850 3BSC950193R1, also cataloged as the TB850 CEX-Bus Terminator, provides direct electrical termination for CEX-Bus communication networks in ABB industrial control platforms. It applies a 120 ohm termination resistance through a 25-pin DB25P male connector interface to maintain bus signal integrity. Hardware Specifications Parameter Specification Model TB850 3BSC950193R1 Brand ABB Product Type CEX-Bus Terminator Origin Sweden Weight 0.05 kg Dimensions 6.5 x 2.5 x 4.2 cm Operating Temp -25 deg C to +70 deg C Storage Temp -40 deg C to +85 deg C Power Consumption Passive termination device, no external power required Bus Interface CEX-Bus Termination Resistance 120 ohm Bus Voltage 5 VDC Connector Type 25-pin DB25P male connector Cable Interface 9-pin D-sub connector or terminal block compatible interface Humidity 5-95% RH, non-condensing Pollution Degree 2 Tariff Code 8537101190 ABB Industrial Control Bus Signal Termination The ABB TB850 supports CEX-Bus communication stability by providing the required end-of-line termination resistance. Therefore, the module reduces signal reflections on the communication line and maintains correct electrical characteristics across connected CEX-Bus segments. For ABB PLC and DCS configurations, CEX-Bus communication depends on correct termination placement. The TB850 installs at the designated bus endpoint and works as a passive electrical component without firmware configuration or parameter settings. Additionally, ABB control system installations require correct connector seating and cable routing to maintain communication performance. The termination resistor directly matches the bus impedance requirement of 120 ohm. Frequently Asked Questions Q: What is the primary function of the ABB TB850 3BSC950193R1?A: The TB850 functions as a CEX-Bus terminator by providing a 120 ohm termination resistance at the communication bus endpoint. Q: Does the TB850 require external power or firmware configuration?A: No. The TB850 is a passive termination component and does not require external power, firmware loading, or software configuration. Q: What installation consideration applies to the TB850 connection?A: The installer should place the terminator at the correct CEX-Bus endpoint and verify proper connector engagement and cable shielding practices. Field Installation Guidelines Install the TB850 only at the specified CEX-Bus termination position within the ABB control system configuration. Verify that the communication cable connection is fully seated before system startup. Maintain proper cable separation from high-voltage power wiring to reduce electromagnetic interference. Connect cable shields according to the ABB system grounding specification. Avoid mechanical stress on the DB25 connector during installation and maintenance operations. Confirm bus continuity and termination resistance before commissioning the communication network.
$199.00 $99.00
-
ABB TB846 3BSE021439R1 ABB Advant S800 I/O Dual Modulebus Inlet Module
ABB TB846 3BSE021439R1 Dual Modulebus Inlet Module Configured for redundant ModuleBus cable adaptation in ABB S800 I/O systems, the ABB TB846 3BSE021439R1 (TB846 Dual Modulebus Inlet Module) provides direct physical connection and signal routing between redundant ModuleBus communication paths. Hardware Specifications Parameter Specification Model TB846 3BSE021439R1 Brand ABB Product Type Dual Modulebus Inlet Module Article Number 3BSE021439R1 Spare Model TB846 System Platform ABB S800 I/O Function Redundant ModuleBus Cable Adaptor Data Rate 1 Mbit/s Origin Sweden Weight 0.04 kg Dimensions 1.6 x 5.4 x 5.6 cm Operating Temp -20 deg C to +70 deg C Storage Temp -40 deg C to +85 deg C Humidity 5 - 95 % RH, non-condensing Mechanics S800 ABB S800 ModuleBus Communication Interface The TB846 operates as a passive communication interface component within the ABB S800 I/O architecture. It manages redundant ModuleBus cable connections and supports communication transfer at a 1 Mbit/s data rate. Additionally, the module supports ABB backplane bus communication velocity management within S800 I/O configurations. The hardware design enables I/O density scaling by allowing redundant communication paths between connected S800 components. The TB846 uses the S800 mechanical design format and maintains electrical separation between ModuleBus connection paths. Therefore, installation practices must maintain proper cable routing and grounding according to ABB system documentation. Frequently Asked Questions Q: What is the primary function of the ABB TB846 module?A: The TB846 functions as a Dual Modulebus Inlet Module and provides redundant ModuleBus cable adaptation for ABB S800 I/O systems. Q: Does the TB846 contain active processing functions?A: No. The TB846 is a communication interface component and does not operate as a CPU or signal processing module. Q: What environmental conditions support TB846 installation?A: The module operates from -20 deg C to +70 deg C and supports 5 - 95 % RH non-condensing humidity conditions. Field Installation Guidelines Install the TB846 according to ABB S800 system installation procedures. Verify that ModuleBus cables are correctly seated and mechanically secured before system startup. Keep communication cables separated from high-voltage power wiring to reduce electromagnetic interference. Connect cable shielding according to the applicable ABB grounding recommendations. Before replacing or installing the module, confirm system power status and verify the permitted hot-swap conditions of the connected S800 configuration.
$199.00 $99.00
-
ABB TB852 3BSC950263R1 ABB Advant S800 I/O RCU Link Terminator
ABB TB852 RCU Link Terminator Configured for RCU link termination in ABB Advant Controller and System 800xA platforms, the ABB TB852 3BSC950263R1 (TB852 RCU Link Terminator) provides direct physical termination for redundant control unit communication links. Hardware Specifications Parameter Specification Model TB852 Brand ABB Product Type RCU Link Terminator Product ID 3BSC950263R1 Origin Global ABB supply chain Weight 0.02 kg Dimensions 23 mm width x 20 mm height x 57 mm depth Power Consumption Passive component, no external power consumption Communication Function RCU link signal termination Application Platform ABB Advant Controller / System 800xA environments HS Code 85369095 / 853690 Industrial Control Bus Termination Characteristics The TB852 is a passive termination component designed for ABB redundant control communication networks. It terminates the RCU link electrical path and reduces signal reflection at the communication endpoint. Furthermore, the component supports stable data transmission by maintaining the correct termination state of the RCU communication circuit. ABB industrial control architectures use this type of termination hardware to preserve communication quality between redundant processing units and associated control modules. For ABB PLC and DCS installations, proper backplane bus communication velocity management and I/O density scaling depend on correct physical network configuration. Therefore, TB852 installation must follow the controller hardware topology requirements defined for the specific ABB control system. Frequently Asked Questions Q: What is the primary function of ABB TB852 3BSC950263R1?A: The TB852 functions as an RCU Link Terminator. It provides endpoint termination for the ABB RCU communication link and maintains proper electrical signal conditions. Q: Does the TB852 require an external power supply?A: No. The TB852 is a passive termination component and does not require an external power connection. Q: Can the TB852 be installed in any ABB control network position?A: No. The TB852 must be installed at the designated termination point of the RCU link according to the ABB system hardware configuration. Field Installation Guidelines Install the TB852 only at the specified RCU link termination position within the ABB control architecture. Verify that the communication cable routing matches the ABB controller installation documentation. Maintain separation between communication wiring and high-voltage power cables to reduce electrical interference. Confirm connector seating and mechanical fixation before system startup. Follow ABB grounding and shielding practices for connected communication cables. Do not modify the passive termination circuitry or replace the component with non-approved termination devices.
$199.00 $99.00
-
ABB TB815 3BSE013204R1 ABB Advant S800 I/O Interconnection Units
ABB TB815 3BSE013204R1 Interconnection Unit Configured for ModuleBus interconnection and termination functions in ABB Advant Master Process Control System platforms, the ABB TB815 3BSE013204R1 (TB815 Interconnection Unit) provides direct physical connection between ModuleBus segments with an integrated TB807 ModuleBus Terminator. Hardware Specifications Parameter Specification Model TB815 3BSE013204R1 Brand ABB Product Type I-O Module / Interconnection Unit Origin Sweden Weight 0.25 kg Dimensions 90 mm depth x 250 mm height x 50 mm width Power Consumption Passive interconnection component, no external power consumption specified Included Components 1 pc TB815 Interconnection Unit and 1 pc TB807 ModuleBus Terminator ModuleBus Function Physical interconnection and termination of ModuleBus communication lines Product Family ABB Advant Master Process Control System RoHS Status Exempted according to EU Directive 2011/65/EU Article 2(4)(c), (e), (f), and (j) ABB Industrial Control Bus Integration The TB815 operates as a passive ModuleBus interconnection component within ABB industrial control architectures. It connects ModuleBus sections and maintains the required termination arrangement through the included TB807 ModuleBus Terminator. Furthermore, ABB ModuleBus designs use controlled communication paths between I/O units and controller interfaces. Therefore, correct installation of the TB815 supports stable backplane bus communication velocity and proper I/O density scaling within compatible ABB S800 and Advant control configurations. The unit does not provide signal processing, firmware execution, or field signal conversion. Instead, it performs physical network arrangement functions between ModuleBus components. Frequently Asked Questions Q: What components are included with the ABB TB815 3BSE013204R1?A: The assembly includes one TB815 Interconnection Unit and one TB807 ModuleBus Terminator. Q: Does the TB815 require an external power supply?A: No. The TB815 is a passive interconnection component and does not require an external power connection. Q: What communication function does the TB815 provide in an ABB system?A: The TB815 provides physical ModuleBus interconnection and termination functions for compatible ABB control system configurations. Field Installation Guidelines Install the TB815 according to ABB system configuration drawings and ModuleBus installation instructions. Verify that the included TB807 ModuleBus Terminator is installed in the designated termination position. Keep ModuleBus wiring separated from high-voltage power cables to reduce electromagnetic interference. Maintain proper cable routing and grounding practices according to ABB industrial control cabinet standards. Inspect connector alignment before mounting the unit to prevent mechanical damage. Confirm ModuleBus communication integrity after installation through the system diagnostic functions.
$199.00 $99.00
-
ABB TB807 3BSE00853R1 Modulebus ABB Advant S800 I/O Termination Units
ABB TB807 Modulebus Terminator The ABB 3BSE008538R1, also cataloged as the TB807 Modulebus Terminator, operates as a passive termination unit for completing Modulebus communication lines within ABB S800 I/O system configurations. Hardware Specifications Parameter Specification Model TB807 3BSE008538R1 Brand ABB Product Type Modulebus Termination Unit Origin Sweden Weight 10 g Dimensions Width: 17 mm; Depth: 13 mm; Height: 19 mm Operating Temp 0 to +55 deg C Storage Temperature -25 to +70 deg C Power Consumption Passive unit, no external power consumption Mechanical Platform S800 Protection Class IP20 according to IEC 60529 Pollution Degree Degree 2 according to IEC 60664-1 Electrical Safety IEC 61131-2, UL 61010-1, UL 61010-2-201 EMC Compliance EN 61000-6-4 and EN 61000-6-2 Corrosion Protection ISA-S71.04: G3 RoHS Compliance EU RoHS, UAE RoHS, CN RoHS WEEE Compliance Directive 2012/19/EU Hazardous Location Certification C1 Div 2 cULus, C1 Zone 2 cULus, ATEX Zone 2 Marine Certification ABS, BV, DNV, LR Modulebus Termination Function The ABB TB807 provides physical termination for the S800 Modulebus network. The unit completes the communication bus structure by applying the required termination impedance at the end of the Modulebus segment. Therefore, it prevents signal reflections and maintains correct bus electrical characteristics. The TB807 uses a passive design without active electronics or external power input. Additionally, its compact S800 mechanical format supports installation within ABB I/O assemblies where space requirements apply. Frequently Asked Questions Q: What is the primary function of the ABB TB807?A: The TB807 functions as a passive Modulebus termination unit. It terminates the end of an S800 Modulebus segment and maintains proper bus signal conditions. Q: Does the TB807 require a power supply connection?A: No. The TB807 is a passive component and does not require external power or firmware configuration. Q: Which ABB system platform uses the TB807?A: The TB807 belongs to the ABB S800 mechanical platform and is designed for Modulebus termination applications. Field Installation Guidelines Install the TB807 at the designated end position of the Modulebus communication segment according to ABB system configuration requirements. Verify that the termination unit is installed securely within the S800 hardware assembly. Maintain proper cable routing and avoid parallel installation with high-current power conductors to reduce electromagnetic interference. Follow ABB grounding and shielding practices for Modulebus cable installations. Confirm that environmental conditions remain within the specified operating temperature, humidity, and protection class limits. Inspect mechanical connections during commissioning to ensure correct physical placement and bus continuity.
$199.00 $99.00
-
ABB ABB TB511-ETH AC500 V2 Terminal Base
ABB TB511-ETH AC500 V2 Terminal Base Configured for Ethernet and serial communication module integration in AC500 V2 PLC systems, the ABB TB511-ETH (TB511-ETH Terminal Base) provides physical connection support for communication interfaces including Ethernet, RS232, and RS485 within ABB AC500 V2 platforms. Hardware Specifications Parameter Specification Model TB511-ETH Brand ABB Origin Sweden Product Type Terminal Base System Platform ABB AC500 V2 Communication Interfaces Ethernet, 2 x serial interfaces RS232/RS485 Communication Connector Type D-SUB, RJ45, Terminals Communication Module Slot 1 slot Supply Voltage 24 V DC Input Voltage Type DC Degree of Protection IP20 Operating Temp 0 to +60 deg C Storage Temperature -40 to +70 deg C Weight 0.159 kg Dimensions 28 x 135 x 95.5 mm PLC Communication Interface Integration The ABB TB511-ETH provides an AC500 V2 terminal base structure with integrated communication interfaces. It supports one communication module slot and combines Ethernet networking with two serial channels based on RS232/RS485 electrical standards. Furthermore, the terminal base supports deterministic PLC communication expansion through ABB AC500 V2 architecture. The design follows industrial PLC backplane communication requirements and enables I/O density scaling within modular controller configurations. The TB511-ETH operates with 24 V DC supply input and maintains IP20 protection for cabinet-based installations. Its Ethernet interface and serial communication ports allow connection between AC500 V2 controllers and external automation devices. Frequently Asked Questions Q: What communication interfaces are available on the ABB TB511-ETH? A: The TB511-ETH provides one Ethernet interface and two serial interfaces supporting RS232 and RS485 communication through D-SUB, RJ45, and terminal connections. Q: Can the TB511-ETH operate outside the AC500 V2 platform? A: The TB511-ETH is designed specifically for ABB AC500 V2 systems and provides the mechanical and electrical interface required by this controller platform. Q: What environmental conditions are specified for TB511-ETH operation? A: The module supports operation from 0 to +60 deg C and storage from -40 to +70 deg C according to ABB technical specifications. Field Installation Guidelines Install the TB511-ETH on a compatible ABB AC500 V2 controller assembly according to the system hardware configuration. Verify the 24 V DC supply wiring polarity before applying power. Connect Ethernet cables separately from high-voltage power conductors to reduce electromagnetic interference. Route RS232/RS485 communication wiring with appropriate shielding and grounding practices. Confirm terminal connections and connector seating before system commissioning. Maintain cabinet airflow requirements within the specified operating temperature range. Follow ABB AC500 V2 installation documentation for communication module configuration and firmware compatibility.
$199.00 $99.00
-
ABB TB842 3BSE022464R1 ModuleBus Optical Ports ABB S800 I/O
ABB TB842 ModuleBus Optical Port The ABB TB842 3BSE022464R1, also cataloged as the TB842 ModuleBus Optical Port, provides fiber optic communication between CI801 or CI840/CI840A FCI modules and TB820/TB820V2/TB840/TB840A ModuleBus modems within Optical ModuleBus networks. Hardware Specifications Parameter Specification Model TB842 3BSE022464R1 Brand ABB Product Type ModuleBus Optical Port Communication Protocol ModuleBus Origin Sweden Weight 90 g Dimensions Width 17.6 mm, Height 56.7 mm, Depth 42.3 mm Operating Temp 0 to +55 deg C Storage Temp -40 to +70 deg C Power Consumption 0.5 W power dissipation, 20 mA typical 24 VDC consumption ModuleBus Interface Fiber optic interface with one transmit and one receive connection Communication Speed Maximum 10 Mbit/s Optical Wavelength 650 nm Optical Connector Type Agilent, former Hewlett-Packard, Versatile Link Optical Fiber Support Plastic fiber and HCS (Hard Clad Silica) fiber Line Redundancy Supported Module Redundancy Supported Hot Swap Supported Mounting Position Vertical or horizontal Protection Class IP20 according to IEC 60529 Equipment Class Class I according to IEC 60536 Humidity Range 5 to 95 %, non-condensing CE Marking Yes Safety Standards EN 61010-1, UL 61010-1, EN 61010-2-201, UL 61010-2-201 Hazardous Location Approval cULus Hazardous Location Class 1 Zone 2, ATEX Zone 2 Marine Certifications ABS, BV, DNV-GL, LR RoHS Compliance EU RoHS, UAE RoHS, CN RoHS WEEE Compliance DIRECTIVE/2012/19/EU ABB Optical ModuleBus Communication Interface The TB842 operates as an optical communication node within ABB ModuleBus architectures. It connects CI801 FCI modules through TB806 and interfaces with CI840/CI840A FCI modules through TU847 and TB806 for single I/O configurations. For redundant I/O configurations, it connects through TU846 and TB846. The module supports both simplex and duplex optical configurations. In simplex operation, optical ModuleBus nodes form a ring structure. In duplex operation, nodes connect in a linear arrangement. Therefore, the TB842 configuration depends on the required network topology and redundancy design. The optical transmitter and receiver support communication rates up to 10 Mbit/s. Additionally, each ModuleBus network must use identical transmitter and receiver types across all connected nodes to maintain communication compatibility. For ABB industrial control systems, the TB842 supports backplane bus communication velocity requirements and I/O density scaling by extending optical ModuleBus connectivity between distributed I/O components and communication interface modules. Frequently Asked Questions Q: What optical fiber types can the ABB TB842 support?A: The TB842 supports plastic optical fiber and HCS (Hard Clad Silica) optical fiber using Agilent, former Hewlett-Packard, Versatile Link connectors. The complete ModuleBus network must use the same transmitter and receiver type. Q: Can the TB842 operate in redundant ModuleBus configurations?A: Yes. The TB842 supports both line redundancy and module redundancy. It can operate in simplex optical ring configurations and duplex optical row configurations according to system architecture requirements. Q: What is the maximum communication speed of the TB842?A: The TB842 optical interface supports a maximum communication speed of 10 Mbit/s with a 650 nm optical wavelength. Field Installation Guidelines Install the TB842 on an ABB-compatible mounting assembly in either vertical or horizontal orientation according to cabinet design requirements. Verify that the selected optical fiber type matches all connected ModuleBus nodes before commissioning. The optical transmitter and receiver types must remain consistent throughout the network. Route fiber optic cables separately from high-voltage power wiring and strong electromagnetic interference sources. Maintain proper bending radius limits specified by the selected fiber manufacturer. Check all Versatile Link optical connectors for correct alignment and clean optical surfaces before connection. Contamination on optical interfaces can reduce signal quality. Confirm 24 VDC power wiring polarity before energizing the module. Use appropriate grounding practices for the cabinet and connected ABB control equipment.
$199.00 $99.00
-
ABB ABB Advant S800 I/O ModuleBus Modem TB820 3BSE008555R1
ABB TB820 ModuleBus Modem The ABB 3BSE008555R1, also cataloged as the TB820 ModuleBus Modem, operates as a dedicated communication interface component for ModuleBus signal transmission and expansion within ABB Advant OCS and AC 400 system architectures. Hardware Specifications Parameter Specification Model TB820 Brand ABB Origin Sweden Power Consumption Supplied through system rack or ModuleBus interface Product Type ModuleBus Modem / Interface Unit Part Number 3BSE008555R1 Communication Function ModuleBus communication extension and interface System Compatibility ABB Advant OCS / AC 400 control systems Mounting Method DIN rail or rack mounting depending on system configuration Signal Interface Electrical or optical ModuleBus communication interface Backplane Bus Communication and I/O Expansion Characteristics The ABB TB820 uses the ABB ModuleBus architecture to transfer communication signals between controller assemblies and connected I/O units. Therefore, the unit provides a physical interface for extending ModuleBus communication paths within compatible ABB control platforms. The module supports structured communication between system nodes and maintains ModuleBus signal integrity through the defined ABB hardware interface. In addition, the TB820 can be integrated into configurations requiring distributed I/O placement and controller-to-I/O communication extension. The ABB industrial control platform design focuses on backplane bus communication velocity, deterministic data exchange, and I/O density scaling. However, TB820 specific firmware flash compatibility and communication parameters depend on the installed ABB system revision and hardware configuration. Frequently Asked Questions Q: What is the primary function of the ABB TB820 3BSE008555R1?A: The TB820 functions as a ModuleBus Modem that provides communication interfacing and expansion capability for ABB ModuleBus-based control systems. Q: Can the TB820 operate as a standalone communication device?A: No. The TB820 requires integration with compatible ABB control hardware and ModuleBus system components for operation. Q: Does the TB820 support optical ModuleBus communication?A: The TB820 is designed for ModuleBus communication extension. The exact optical or electrical interface capability depends on the connected ABB hardware configuration. Field Installation Guidelines Install the ABB TB820 according to the applicable ABB system installation manual and hardware configuration requirements. Verify that the mounting position matches the specified rack or DIN rail arrangement before wiring. Keep ModuleBus communication cables separated from high-voltage power conductors to reduce electrical interference. Connect cable shielding and grounding according to ABB control cabinet grounding practices. Check connector seating, module alignment, and system power conditions before commissioning. Confirm controller recognition and ModuleBus communication status through the ABB engineering tool after installation.
$199.00 $99.00
-
ABB Modulebus Terminator ABB S800 I/O TB807 3BSE008538R1
ABB TB807 Modulebus Terminator Configured for Modulebus line termination in ABB automation system networks, the ABB 3BSE008538R1 (TB807 Modulebus Terminator) provides direct physical termination for Modulebus communication segments. This hardware component maintains bus electrical conditions by completing the communication line structure. Hardware Specifications Parameter Specification Model 3BSE008538R1 ABB Type Designation TB807 Product Type Module Termination Unit Brand ABB Origin Bulgaria Function Modulebus Terminator Communication Interface Modulebus termination interface Weight 0.01 kg Dimensions 13 mm depth x 19 mm height x 17 mm width Operating Temp Not specified Power Consumption Passive termination component; no external power supply required Cable Length 0 m Modulebus Termination and Industrial Bus Control The ABB TB807 terminates Modulebus communication paths within ABB control architectures. Therefore, it provides the required electrical endpoint for bus segments and supports correct signal behavior across connected modules. The unit belongs to ABB Modulebus termination components and operates as a passive hardware element. Additionally, its compact mechanical design allows installation at designated Modulebus endpoint positions without additional wiring length. The TB807 supports ABB industrial control platforms through direct Modulebus interface compatibility. Furthermore, its termination function contributes to stable backplane bus communication velocity and proper I/O density scaling within ABB distributed control configurations. Frequently Asked Questions Q: What is the primary function of the ABB TB807 3BSE008538R1?A: The TB807 functions as a Modulebus terminator. It completes the physical communication line and provides the required termination point for Modulebus segments. Q: Does the TB807 require an external power connection?A: No. The TB807 is a passive termination component and does not require a separate power supply connection. Q: Where should the TB807 be installed in a Modulebus configuration?A: The TB807 should be installed at the designated endpoint of the Modulebus communication path according to ABB system installation documentation. Field Installation Guidelines Install the TB807 only at the specified Modulebus termination position within the ABB control system configuration. Verify that the module connector is fully seated before system commissioning. Keep Modulebus wiring separated from high-voltage power cables to reduce electrical interference. Follow ABB grounding and shielding practices for connected communication cables. Inspect connector conditions and mechanical mounting points during maintenance activities.
$199.00 $99.00
-
ABB TB825 3BSE036634R1 Optical Media Converter ABB Advant S800 I/O
ABB TB825 3BSE036634R1 Optical Media Converter Configured for optical signal conversion in the ABB Modulebus network, the ABB TB825 3BSE036634R1 (TB825 Optical Media Converter) provides direct physical data transmission conversion between electrical and optical communication interfaces. Hardware Specifications Parameter Specification Model TB825 3BSE036634R1 Brand ABB Product Type Optical Media Converter Origin Sweden Weight 0.2 kg Dimensions 10.2 x 5.1 x 15.2 cm Communication Protocol Modulebus Master or Slave Slave Line Redundancy No Power Supply 24 VDC Power Consumption 96 mA typical at 24 VDC Operating Temp 0 to +55 deg C (+32 to +131 deg F), approvals issued for +5 to +55 deg C Storage Temp -40 to +70 deg C (-40 to +158 deg F) Relative Humidity 5 to 95 %, non-condensing Hazardous Location Approval C1 Div 2 cULus, C1 Zone 2 cULus, ATEX Zone 2 Marine Certificates ABS, BV, DNV-GL, LR Modulebus Optical Communication Conversion The ABB TB825 3BSE036634R1 performs optical media conversion within ABB industrial control architectures using Modulebus communication. Therefore, the module transfers communication signals through optical interfaces to support extended network connections and electrical isolation between connected segments. Additionally, the TB825 operates as a slave device on the Modulebus network. The module supports a 24 VDC power input with a typical current consumption of 96 mA and does not provide line redundancy functionality. For ABB automation platforms, communication performance depends on the Modulebus configuration, connected controller capacity, and installed firmware compatibility. Furthermore, the optical conversion function helps separate communication segments where electrical signal transmission limitations exist. Frequently Asked Questions Q: What communication protocol does the ABB TB825 3BSE036634R1 support?A: The TB825 supports the ABB Modulebus communication protocol and operates as a slave device within the network structure. Q: Does the TB825 provide redundant communication lines?A: No. The TB825 specification indicates that line redundancy is not supported. Q: What power supply is required for the TB825 module?A: The TB825 requires a 24 VDC supply and consumes approximately 96 mA under typical operating conditions. Field Installation Guidelines Install the TB825 module according to the ABB system hardware configuration requirements. Verify that the 24 VDC power supply polarity matches the module connection specification before energizing the unit. Route optical communication cables separately from high-voltage power cables to reduce electromagnetic interference risks. Maintain proper optical connector cleanliness because contamination can affect signal transmission quality. Confirm hazardous location requirements before installation in classified areas. Ensure the ambient temperature and humidity remain within the specified operating limits.
$199.00 $99.00
-
ABB Power Supply Device ABB Advant S800 I/O Power Supply Devices
ABB SD821 Power Supply Device The ABB SD821 3BSC610037R1, also cataloged as the SD821 Power Supply Device, operates as a dedicated hardware component for converting incoming AC power into regulated 24 VDC output within ABB industrial control system platforms. Hardware Specifications Parameter Specification Model SD821 Brand ABB Origin Sweden Weight 0.44 kg Dimensions 5 x 10.6 x 13 cm Operating Temp Not specified Power Consumption 2.5 A output rating Input Voltage 230 VAC Output Voltage 24 VDC Product Type Power Supply Device Spare Model 3BSC610037R1 Manufacturer Status Discontinued by manufacturer Industrial Control Power Conversion Characteristics The ABB SD821 power supply device provides AC to DC conversion for ABB automation hardware installations. It accepts a 230 VAC input source and delivers a 24 VDC output supply for connected control components. Furthermore, the SD821 supports ABB system power distribution requirements through regulated DC output. The module design aligns with industrial cabinet installation practices where stable DC voltage distribution supports PLC, DCS, and I/O hardware operation. For ABB control platforms, power supply integration requires consideration of backplane bus communication velocity, I/O density scaling, and firmware flash compatibility across connected hardware modules. Therefore, engineers should verify system-level power requirements before installation or replacement. Frequently Asked Questions Q: What is the primary electrical function of the ABB SD821?A: The ABB SD821 converts a 230 VAC input supply into a 24 VDC output supply for industrial automation equipment. Q: Can the SD821 be used as a direct replacement for another power supply module?A: Replacement selection requires verification of voltage rating, current capacity, mechanical dimensions, and ABB system compatibility. Q: Does the SD821 support redundant power supply configuration?A: The provided technical data does not specify redundancy capability. System documentation should be checked before implementing parallel or backup power arrangements. Field Installation Guidelines Install the ABB SD821 inside a suitable industrial control cabinet with appropriate ventilation and mechanical support. Connect the 230 VAC input wiring according to the applicable electrical installation standard. Verify polarity and grounding requirements on the 24 VDC output side before connecting field devices. Keep AC input wiring separated from low-voltage DC signal cables to reduce electrical interference. Use proper grounding methods for cabinet assemblies and maintain clean cable routing around control modules. Before energizing the system, confirm input voltage level, output voltage stability, and load requirements against the installed automation hardware specifications.
$199.00 $99.00
-
ABB ABB Advant S800 I/O SD822 3BSC610038R1 Power Supply Module
ABB SD822 3BSC610038R1 Power Supply Module The ABB SD822 3BSC610038R1, also cataloged as the SD822 Power Supply Module, operates as a dedicated hardware component for AC to 24 VDC power conversion within ABB industrial control system platforms. It provides a 230 VAC input interface and a 5 A rated 24 VDC output supply for connected control equipment. Hardware Specifications Parameter Specification Model SD822 3BSC610038R1 Brand ABB Product Type Power Supply Module Origin Sweden Weight 0.6 kg Dimensions 6.3 x 10.5 x 13.1 cm Input Voltage 230 VAC Output Voltage 24 VDC Output Current 5 A Power Supply 100 - 120 VAC Power Consumption 150 VA typical Operating Temp 0 - +50 deg C Storage Temp -40 - +70 deg C Humidity 5 - 95 % RH non-condensing Tariff Code 8537101190 Industrial Control Power Integration The ABB SD822 power supply module supports industrial control power distribution through regulated 24 VDC output conversion. Furthermore, the module design aligns with ABB PLC and DCS hardware environments where stable DC power is required for I/O assemblies, controllers, and auxiliary control circuits. ABB system power architectures typically use modular power distribution methods with controlled load allocation. Therefore, correct installation requires verification of input voltage range, output polarity, grounding arrangement, and connected load requirements before energizing the module. The module operates as a power conversion component rather than a communication device. It does not provide field signal processing, protocol conversion, or I/O channel management functions. Its primary function is supplying DC operating power to compatible automation hardware. Frequently Asked Questions Q: What is the primary function of the ABB SD822 3BSC610038R1 module?A: The SD822 3BSC610038R1 converts AC input power into a regulated 24 VDC output supply for ABB industrial automation equipment. Q: Does the SD822 module provide communication or field signal interfaces?A: No. The SD822 is a power supply module and does not include communication ports, analog input channels, or digital I/O functions. Q: What environmental conditions are specified for SD822 operation?A: The module supports an operating temperature range of 0 to +50 deg C and storage conditions from -40 to +70 deg C with 5 - 95 % RH non-condensing humidity. Field Installation Guidelines Install the SD822 module according to the applicable ABB system cabinet layout and mounting requirements. Verify AC input wiring before connection to prevent incorrect voltage application. Maintain correct polarity when connecting the 24 VDC output terminals to downstream equipment. Connect protective grounding according to industrial electrical installation standards. Separate power wiring from sensitive signal cables to reduce electrical interference. Check terminal tightening conditions before system startup. Confirm the connected load remains within the specified power supply capacity.
$199.00 $99.00
-
ABB ABB DO620 3BHT300009R1 Advant S600 Digital Output Module
DescriptionThe ABB DO620 (3BHT300009R1) is a high-density digital output module designed for use within the Advant S600 I/O system. This module provides 32 digital output channels, organized into four isolated groups, to facilitate reliable control signal distribution in industrial automation environments. As a component of the Advant Controller 110/160 series, it is engineered for robust performance in demanding process control applications.Features 32-channel digital output configuration Four isolated groups for enhanced signal separation Maximum switching capacity of 500mA per channel Operational voltage rating up to 60VDC Designed for the Advant S600 I/O platform Technical Specifications Product Model DO620 Order Code 3BHT300009R1 Number of Channels 32 Output Type Digital Output Isolation 4 Groups Max Current per Channel 500mA Max Voltage 60VDC System Compatibility Advant S600 Weight 1.16 kg Installation Guidelines Ensure the controller power is disconnected before installing or removing the module from the S600 I/O rack. Handle the module using proper ESD (Electrostatic Discharge) precautions to prevent damage to internal circuitry. Verify that the module is firmly seated in the backplane connector to ensure reliable communication and power distribution. Route signal wiring away from high-voltage power cables and sources of electromagnetic interference (EMI) to maintain signal integrity. Ensure proper grounding of the I/O rack according to ABB installation standards for the Advant system. FAQIs the ABB DO620 still in production?No, the ABB DO620 (3BHT300009R1) has been discontinued by the manufacturer. We provide high-quality surplus and refurbished units to support legacy system maintenance.What systems is the DO620 compatible with?The DO620 is specifically designed for the ABB Advant S600 I/O system, commonly used with Advant Controller 110 and 160 series hardware.
$199.00 $99.00
لقد شاهدت 312 من أصل 1117 منتجًا