Description

GE DS200TCCBG3ANE Mark V/VI Thermocouple/Analog Input Board

Configured for precise temperature and sensor signal acquisition in GE Mark V/Mark VI turbine control networks, the GE DS200TCCBG3ANE (DS200TCCB Thermocouple/Analog Input Board) provides direct physical/electrical execution. It directly samples millivolt-level thermocouple outputs, applies per-channel cold junction compensation, and converts field signals to 16-bit digital values across isolated backplane interfaces to ensure stable turbine operation.

Hardware Specifications

Parameter	Specification
Model	DS200TCCBG3ANE
Brand	GE
Origin	USA
Weight	0.48 kg
Dimensions	170 x 145 x 65 mm
Operating Temp	-10 to +55 deg C
Power Supply	24/48 VDC via backplane
Channels	8 isolated thermocouple inputs
Input Range	+/-100 mV
Thermocouple Types	J, K, T, E, N, R, S, B (per-channel configurable)
Resolution	16-bit
Accuracy	+/-0.2 deg C (including CJC and linearization)
Temperature Drift	+/-5 ppm/deg C
CJC Method	Per-channel precision sensors (+/-0.05 deg C)
Isolation	1800 Vrms channel-to-backplane
Common Mode Rejection	115 dB (filtered)
Digital Filtering	Programmable (50 Hz, 60 Hz, 250 Hz, 500 Hz cutoff)
Input Impedance	>10 M ohm
Update Rate	40 ms (all channels synchronized)
Mounting	VME rack / Mark VI backplane

Backplane Bus Communication and Signal Isolation

The DS200TCCBG3ANE interfaces directly with the Mark V/VI control core via high-speed backplane bus communication, delivering deterministic sensor telemetry without network latency overhead. To prevent ground loops caused by high-voltage plant potential differences, the card incorporates 1800 Vrms channel-to-backplane galvanic isolation. Channel-density scaling is optimized for dense turbine exhaust configurations, maintaining high signal-to-noise ratios even in extreme electromagnetic environments. Integrated cold junction compensation (CJC) processing hardware converts raw sensor millivolts locally, reducing host processor firmware overhead during real-time turbine trip evaluation cycles.

Frequently Asked Questions

Q: Can the DS200TCCBG3ANE be hot-swapped during active turbine operation?

A: No, hot-swapping the board while the backplane bus is energized is not permitted. Power off the VME rack or designated panel segment before insertion or removal to prevent backplane bus disturbance or damage to sensitive analog conversion components.

Q: How does channel-to-backplane galvanic isolation impact sensor wiring safety?

A: The 1800 Vrms galvanic isolation barrier prevents high transient voltages on sensor field leads from penetrating the control system backplane, protecting core CPU modules and preventing ground loop currents from degrading 16-bit ADC measurement precision.

Q: What grounding method is required for thermocouple signal shielding?

A: Thermocouple extension cables must have their individual and overall shields grounded at a single point on the designated system ground bar inside the cabinet. Never ground the shield at both the sensor head and the control cabinet, as ground potential differentials introduce measurement errors.

Field Installation Guidelines

1. Ensure the VME rack slot or Mark VI backplane position is fully de-energized prior to seating the module.
2. Verify card edge connectors for bent pins or debris before sliding the board into the card cage guide rails.
3. Tighten the top and bottom retaining screws on the front panel to ensure solid frame grounding and prevent board dislodgement from vibration.
4. Route thermocouple field wiring in separate conduits away from high-voltage AC motor drives and heavy inductive loads to prevent electromagnetic coupling.
5. Terminate shield conductors to the dedicated panel earth bar using short, direct ground leads. Maintain a minimum thread engagement of 5 full turns on NPT ground lugs.

Specifications

• Brand: General Electric

Advantages

• High reliability in industrial environments
• Supports continuous operation
• Compatible with major PLC/DCS systems