The Bently Nevada 3500 Series offers advanced condition monitoring for critical industrial machinery. We provide modules, probes, and spare parts to ensure uninterrupted operation.
Bently Nevada 3500 Series
-
Bently Nevada Bently Nevada 3500/22-01-01-05 (138607-01+146031-01) TDI Module
Product Description The Bently Nevada 3500/22-01-01-05 164466-01 Transient Data Interface (TDI) is a rack-level communication and data acquisition module designed for the 3500 Machinery Protection System. It consolidates communication processing, configuration control, and high-speed vibration data handling into a single interface between monitoring hardware and System 1 software. This configuration is equipped with hazardous-area certification (ATEX / IECEx), making it suitable for installations in classified environments such as offshore platforms, refineries, and petrochemical processing units. The module is not part of the protection trip logic. System protection functions remain active even if the TDI is removed or fails. System Role and Architecture Central communication processor for the entire 3500 rack Unified interface for steady-state, dynamic, and transient vibration data Synchronizes data from all M-series monitor modules Stores rack configuration data for system continuity Installed in Slot 1 adjacent to power supply modules Communication and I/O Configuration Rear I/O assembly: 138607-01 + 146031-01 Ethernet interface: 10/100 Base-T (RJ-45 copper connection) Auto-negotiation and auto-MDIX support IEEE 802.3 compliant network communication USB Type-B port for local service access Supported communication functions: System 1 condition monitoring integration High-speed waveform and transient data transfer Rack configuration upload and download Modbus TCP communication via TDI interface Electrical Characteristics Power consumption: 10.5 W (supplied via rack backplane) Operating mode: Normally energized OK relay output (via I/O module): 5 A @ 24 VDC / 120 VAC Maximum load: 120 W / 600 VA Gold-plated low-current contacts (down to 1 mA @ 1 VDC) Integrated arc suppression Front Panel Interface OK LED: Module health status TX/RX LED: Ethernet communication activity CONFIG OK LED: Valid configuration confirmation TM LED: Trip Multiply indication Rack Reset: Clears latched alarms Address switch: Rack ID assignment (1–127) Keylock switch: RUN / PROGRAM mode control Environmental Ratings Operating temperature: -30°C to +65°C Storage temperature: -40°C to +85°C Relative humidity: 0–95% non-condensing Hazardous area certification: ATEX / IECEx Zone 2 (option code “05”) Designed for harsh industrial and offshore environments Functional Capabilities Combines rack interface and communication processing functions Captures static, dynamic, and transient vibration signatures Supports high-resolution transient acquisition via channel enabling features Fully compatible with M-series monitors (e.g., 3500/40M, 3500/42M, 3500/45M) Enables Modbus TCP and System 1 connectivity Hot-swappable design for maintenance without system shutdown Applications Oil & gas rotating equipment monitoring systems Offshore turbine and compressor protection systems Petrochemical plant vibration diagnostics Power generation machinery condition monitoring Critical asset health management systems FAQ Q1: Does this module affect machine protection if it fails?No. The TDI operates outside the protection path and does not influence trip functions. Q2: What is the purpose of the “05” option code?It designates ATEX/IECEx certification for hazardous-area installation. Q3: Can it capture transient events during machine startup?Yes. It is designed specifically for high-speed waveform capture during operational transitions.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/22-01-01-01 Transient Data Interface Module
Product Description The Bently Nevada 3500/22-01-01-01 164466-01 Transient Data Interface (TDI) functions as the central communications and data coordination module within the 3500 Machinery Protection System. It unifies rack-level configuration control with high-speed data exchange capabilities, acting as the primary bridge between monitoring hardware and System 1 diagnostic software. This module replaces the traditional rack interface architecture while extending functionality to include advanced transient data capture, enabling detailed analysis of machine behavior during start-up, shutdown, and operational disturbances. It does not participate in the protection trip path, ensuring monitoring continuity even during module maintenance or failure. System Architecture & Function Combines rack interface and communication processor roles into a single module Provides continuous access to both steady-state and dynamic vibration data Supports synchronized data acquisition across all compatible monitor modules Maintains rack configuration memory for seamless module replacement Designed as Slot 1 resident module within the 3500 rack backplane Communication Capabilities Ethernet 10/100 Base-T auto-sensing interface USB Type-B port for local service and configuration access Supports System 1 software integration for real-time condition monitoring Enables rack-level configuration upload and download Compatible with Bently Nevada proprietary communication protocols and Modbus TCP via gateway configuration Electrical Specifications Power consumption: approximately 10.5 W (supplied via rack backplane) OK relay output: Rated 5 A @ 24 VDC / 120 VAC Maximum load 120 W / 600 VA Gold-plated contacts with low-current capability (1 mA @ 1 VDC minimum) Normally energized operation with built-in arc suppression Front Panel Interface OK status indicator for module health TX/RX LEDs for communication activity monitoring CONFIG OK indicator for validated configuration state TM (Trip Multiply) status indicator Rack reset pushbutton for alarm clearing Address switch for rack identification (1–127 range) Keylock switch supporting RUN and PROGRAM modes Mechanical Data TDI module size: 241.3 × 24.4 × 241.8 mm Weight: 0.91 kg Installation: Front slot (TDI) + rear I/O slot within 3500 rack frame Environmental Suitability Operating temperature range: -40°C to +85°C Designed for installation in protected industrial cabinet environments Suitable for continuous operation in high-reliability monitoring systems Ruggedized for petrochemical, power generation, and rotating equipment applications Functional Highlights Integrates legacy rack interface and communication processing functions Captures transient waveform data during machine speed transitions Supports optional advanced channel enabling for extended diagnostics Fully compatible with all M-series monitoring modules Hot-swappable design for maintenance without system shutdown Applications Turbomachinery vibration monitoring systems Gas and steam turbine condition diagnostics Compressor train protection and analysis Critical rotating asset performance monitoring Plant-wide machinery health management platforms FAQ Q1: Does this module affect protection logic if it fails?No. The TDI operates outside the protection loop and does not influence trip logic. Q2: Can it record startup vibration events?Yes. It is designed specifically for transient event capture during speed changes. Q3: Is System 1 required for full functionality?Yes. Advanced diagnostics and waveform analysis require System 1 integration.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/22 164466-01 Transient Data Interface Module
Product Description The Bently Nevada 3500/22M 164466-01 Transient Data Interface (TDI) serves as the central communications and data acquisition gateway for the 3500 Machinery Protection System. It consolidates rack-level communication, configuration control, and high-resolution vibration data transfer into a single integrated module. Functionally, this module replaces the legacy rack interface role while extending capability into advanced transient data capture, enabling detailed machinery behavior analysis during start-up, coast-down, and process disturbances. It is engineered for continuous integration with System 1 condition monitoring software. Designed for reliability in critical rotating equipment environments, the module ensures that both static and dynamic machine data are reliably transmitted, stored, and synchronized across the monitoring architecture. Technical Specifications Model: 3500/22M Part Number: 164466-01 Module Type: Transient Data Interface (TDI) / Rack Communication Gateway System Compatibility: Bently Nevada 3500 Series Racks (3500/05 and variants) Primary Function: Rack configuration management + high-speed machinery data interface Data Types Supported: Static process variables Dynamic vibration waveforms Transient event data (start-up / coast-down) Alarm and system event logs Communication Interfaces: Ethernet 10/100 Base-T USB Type-B service port Protocols: Bently Nevada proprietary protocol, Modbus TCP (via gateway configuration) Control Inputs: Rack reset input, OK relay status output Front Panel Indicators: Power/OK status, TX/RX communication activity, configuration status, test mode indicator Power Consumption: ~5–7 W (typical operating range depending on configuration) Operating Temperature: -30°C to +65°C Mounting Location: Slot 1 of 3500 rack (system dedicated position) Configuration Storage: Non-volatile rack configuration memory for module interchange support Key Functional Characteristics Centralized communication bridge between rack hardware and System 1 software platform Enables transient waveform capture during mechanical speed variation events Maintains rack configuration integrity during module replacement or hot-swap events Supports synchronized diagnostic data acquisition across multiple monitor modules Provides diagnostic visibility into vibration trends, phase, and spectral behavior Applications Turbomachinery condition monitoring systems Steam and gas turbine protection architectures Compressor vibration diagnostics Critical rotating equipment health management Continuous plant-wide machinery protection systems FAQ Q1: Does the 3500/22M replace the rack interface module?Yes. It integrates the functions of the legacy rack interface while adding transient data processing capability. Q2: Can it capture startup vibration data?Yes. It is specifically designed to capture high-resolution transient waveforms during speed changes. Q3: Is System 1 software required?It is fully optimized for System 1 integration, which is required for advanced diagnostic visualization and analytics.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/22 146031-02 Transient Data Interface Module
Product Description The 3500/22M (146031-02) is a Transient Data Interface module designed for the Bently Nevada 3500 machinery protection platform. It serves as the central communication and data acquisition hub for the rack, combining the functions of a rack interface unit and communication processor into a single integrated module. Installed in Slot 1 of the 3500 rack, this module manages system-level communication, configuration handling, and high-speed data exchange between monitoring modules and external software systems. This version features fiber-optic Ethernet connectivity, making it suitable for electrically noisy or long-distance industrial installations. Importantly, the module operates outside the protection voting path, ensuring that a failure does not impact machinery protection functionality. Core Functions Central communication gateway for 3500 rack systems Collects steady-state, dynamic, and transient vibration data Enables high-speed integration with System 1 software platform Supports full rack configuration upload and download Interfaces with all M-series monitoring modules Provides diagnostic and system health communication Maintains independence from protection logic path Communication Interfaces Interface Specification Primary Ethernet 100Base-FX Fiber Optic Secondary Ethernet 10/100Base-TX Copper Local Port USB-B for configuration access Auto Negotiation Supported Auto Sensing Supported Fiber-optic communication provides enhanced immunity to electrical noise and supports extended transmission distances in industrial environments. Electrical Characteristics Parameter Specification Power Supply Provided via 3500 rack backplane Power Consumption 10.5 W Module Function Communication and data interface Operating Role Non-protective system component OK Relay Specifications Parameter Specification Contact Rating 5 A @ 24 VDC / 120 VAC Maximum Load 120 W / 600 VA Minimum Switching Load 1 mA @ 1 VDC Contact Type Gold-plated contacts Protection Arc suppression included Operation Mode Normally energized Front Panel Indicators & Controls Indicator Function OK LED System operational status TX/RX LED Communication activity TM LED Trip Multiply status CONFIG OK LED Valid configuration status Control Function Rack Reset Button Clears latched alarms Address Switch Rack address configuration (1–127) Key Switch RUN / PROGRAM mode selection Mechanical Specifications Parameter Specification Model 3500/22M (146031-02) Module Type Transient Data Interface (TDI) Mounting Location Slot 1 of 3500 rack Dimensions 241.3 × 24.4 × 241.8 mm Weight 0.82 kg Installation Type Front module with rear I/O interface Environmental Ratings Operating Temperature: 0°C to +60°C Storage Temperature: -40°C to +85°C Designed for harsh industrial conditions Suitable for power plants, refineries, compressors, and turbine systems High resistance to electrical noise and vibration environments Functional Role Within the 3500 system architecture, the 3500/22M (146031-02) acts as the primary data and communication hub. It: Aggregates machine condition data across all modules Enables real-time transient event capture Provides secure communication with System 1 software Supports remote diagnostics and system configuration Ensures separation from safety and protection logic functions FAQ Is this module required for system protection?No. It supports communication and data acquisition only and does not participate in protection decisions. What advantage does fiber optic communication provide?It improves noise immunity and supports long-distance, high-speed data transmission in harsh environments. Can the system operate without this module?Yes, but advanced data acquisition and System 1 integration will not be available. Is this module hot-swappable?Yes, it can be replaced without shutting down the rack under normal operating conditions.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/22 161580-01 Transient Data Interface Module
Overview The 3500/22 (161580-01) Transient Data Interface (TDI) functions as the central communication controller within the Bently Nevada 3500 machinery protection architecture. It establishes the data exchange bridge between the monitoring rack and external condition monitoring platforms, primarily System 1 software. This module replaces the legacy rack interface architecture and integrates both communication handling and transient data acquisition into a single front-end processor. Installed in Slot 1 of the rack, it operates adjacent to the power supply modules and interfaces directly with all M-series monitoring modules. Technical Summary Parameter Specification Module Type Transient Data Interface (TDI) Part Number 161580-01 Power Consumption 10.5 W Ethernet Interfaces 10/100Base-TX, 100Base-FX USB Interface USB-B Relay Rating 5 A @ 24 VDC / 120 VAC Rack Position Slot 1 System Compatibility 3500 M-series modules System Communication Role The 161580-01 module manages continuous data acquisition from connected monitors, supporting multiple data types: Steady-state vibration parameters Dynamic waveform streams High-resolution transient event records (requires channel enabling configuration) It aggregates rack-level diagnostic information and transmits it to supervisory systems without being part of the protection voting logic. Failure of this module does not interrupt machinery protection functions. Communication Architecture The module provides multi-path connectivity options to ensure flexible integration: 10/100Base-TX Ethernet (auto-negotiating copper interface) 100Base-FX Fiber Ethernet (long-distance, EMI-resistant transmission) USB-B local service port for configuration and diagnostics Supported communication functions include: Real-time waveform streaming Configuration upload and download Integration with plant-wide monitoring systems Communication with all M-series modules including 3500/40M, 3500/42M, and 3500/45M Electrical Characteristics Power supply: Backplane-fed from 3500 rack system Typical power consumption: 10.5 W OK relay output (via I/O module): 5 A @ 24 VDC / 120 VAC Maximum switching capacity: 120 W / 600 VA Gold-plated low-level signal compatibility (down to 1 mA @ 1 VDC) Arc suppression integrated Relay configuration: Normally energized design for fail-safe operation Control & Indication Front panel diagnostics provide real-time system status visibility: OK indicator – module operational status TX/RX indicator – data transmission activity TM indicator – trip multiply state CONFIG OK – configuration validation status Address selector – rack identification (1–127 range) Reset function – clears latched system alarms Key switch – operational mode control (RUN / PROGRAM) Mechanical Integration Installation position: Slot 1 of 3500 rack Configuration: Full-height module architecture Rear I/O section: Supports Ethernet and relay termination Designed for tool-free hot-swap replacement when rack configuration permits Environmental Performance Engineered for continuous operation in demanding industrial environments: Continuous operation in harsh plant conditions Suitable for turbine, compressor, refinery, and power generation systems Storage and operating tolerances aligned with 3500 platform standards High immunity to electrical noise when paired with fiber-optic interface Functional Summary Acts as the primary data gateway for the 3500 rack Consolidates vibration and transient data streams Enables System 1 predictive monitoring integration Supports modular scalability across M-series monitor platforms Allows maintenance replacement without system shutdown Provides centralized rack communication synchronization FAQ Q1: Does this module affect protection logic?No. The 161580-01 operates outside the protection path and does not influence trip decisions. Q2: Can it be replaced while the system is running?Yes, it supports hot-swapping when system configuration permits redundancy. Q3: What systems is it compatible with?It is fully compatible with Bently Nevada 3500 M-series monitoring modules and System 1 software platforms.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/22 146031-01 Ethernet I/O Communication Module
Product Description The 3500/22 (146031-01) is a rear-installed Ethernet communication interface designed for the Bently Nevada 3500/22M Transient Data Interface system. Positioned behind Slot 1 of the rack, it serves as the primary network gateway between the monitoring rack and external condition monitoring platforms such as System 1. This module replaces earlier communication components used in legacy 3500 architectures, consolidating network connectivity and data exchange functions into a dedicated Ethernet interface unit. It is strictly a communication component and does not participate in machinery protection logic or voting functions. A failure of this module does not interrupt the protective operation of the 3500 rack. Core Functions Provides Ethernet connectivity for 3500 rack systems Enables communication with System 1 software platform Transfers steady-state and transient vibration data Supports rack configuration upload and download Interfaces with M-series monitoring modules Acts as communication bridge for diagnostic data Maintains isolation from protection logic path Communication Specifications Parameter Specification Ethernet Type 10Base-T / 100Base-TX Connector Type RJ-45 Copper Interface Auto Negotiation Supported Auto MDIX Supported Standards IEEE 802.3 / 802.3u Data Rate 10 / 100 Mbps Electrical Characteristics Parameter Specification Power Source Supplied via 3500 rack backplane Associated Module 3500/22M TDI Power Consumption ~10.5 W (system dependent) Function Ethernet and rack communication interface Relay Output OK relay via TDI system OK Relay Specifications Parameter Specification Contact Rating 5 A @ 24 VDC / 120 VAC Minimum Load 1 mA @ 1 VDC Contact Type Gold-plated contacts Protection Arc suppression integrated Operation Mode Normally energized system logic Front Panel Indicators (via TDI System) Indicator Function OK LED System operational status TX/RX LED Network communication activity TM LED Trip Multiply status CONFIG OK LED Valid configuration confirmation Control Function Rack Reset Button Clears latched alarms Address Switch Rack address configuration (1–127) Key Switch RUN / PROGRAM mode selection Mechanical Specifications Parameter Specification Model 3500/22 (146031-01) Mounting Location Rear of 3500 rack, Slot 1 rear position Module Type Ethernet I/O interface module Dimensions 3 × 12 × 25 cm Weight 0.45 kg Environmental Ratings Operating Temperature: -30°C to +65°C Storage Temperature: -40°C to +85°C Humidity: Up to 95% non-condensing Designed for continuous industrial-duty environments System Role Within the 3500 architecture, the 3500/22 (146031-01) functions as the communication backbone for the TDI system. It: Enables real-time condition monitoring data transfer Supports vibration waveform and transient event capture Provides Ethernet access for engineering and diagnostic tools Ensures separation from safety and protection logic FAQ Is this module part of the protection system logic?No. It is strictly a communication interface and does not influence protection or trip decisions. What software does it integrate with?It is designed for full compatibility with Bently Nevada System 1 condition monitoring software. Can the system operate without this module?Yes, but remote communication, waveform transfer, and System 1 integration will not be available. What is its primary function in the rack?It provides Ethernet-based communication between the 3500 rack and external monitoring systems.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/22 125768-01 Rack Interface I/O Module
Product Description The 3500/22 (125768-01) is a rear-mounted interface module designed for the Bently Nevada 3500 machinery protection platform. It functions as the physical connection layer for the 3500/22 Transient Data Interface (TDI), enabling communication, configuration access, and high-speed data exchange between the rack and external monitoring systems. Installed at the rear of the rack directly behind the TDI front module, this unit forms part of the system’s communication infrastructure. It is responsible for providing network connectivity and data routing while leaving the protection and voting logic of the system unaffected. The module is not involved in protection decision-making; its role is strictly communication and data handling within the 3500 architecture. Core Functions Provides physical Ethernet interface for 3500/22 TDI Enables high-speed data transmission between rack and external systems Supports configuration upload and download functions Transfers steady-state and transient waveform data Integrates with System 1 condition monitoring software Maintains separation from protection and voting logic Supports remote diagnostic access and rack communication Communication Interfaces Interface Specification Ethernet Port 1 10/100Base-TX (Auto-sensing) Ethernet Port 2 100Base-FX Fiber (configuration dependent) USB Port USB-B (local configuration access) These interfaces allow: High-speed vibration waveform transfer System 1 connectivity Remote diagnostics and monitoring Rack configuration management Electrical Characteristics Parameter Specification Power Source Supplied via 3500 rack backplane Function Ethernet and configuration I/O interface Relay Support Provided via associated TDI module Relay Rating 5 A @ 24 VDC / 120 VAC Contact Type Gold-plated, low-current compatible Minimum Switching Load 1 mA @ 1 VDC Arc Protection Integrated suppression circuit Front Panel Indicators & Controls (via TDI System) Indicator Function OK LED Normal system operation TX/RX LED Communication activity status TM LED Trip Multiply active state CONFIG OK LED Valid configuration status Control Function Rack Reset Button Clears latched alarms and faults Address Switch Configures rack address (1–127) Mode Key Switch Selects RUN or PROGRAM mode Mechanical Details Parameter Specification Model 3500/22 (125768-01) Mounting Location Rear of 3500 rack, behind TDI module Module Type Rear interface I/O assembly Dimensions 2.5 × 11.2 × 24.2 cm Weight 0.45 kg Environmental Design Engineered for continuous operation in harsh industrial environments Suitable for high-vibration and high-noise electrical areas Commonly deployed in process plants, turbine halls, and compressor stations Compatible with long-term monitoring installations System Role Within the 3500 architecture, the 3500/22 (125768-01) performs as a communication backbone component. It: Bridges rack-level data with external monitoring systems Supports real-time waveform and transient event transmission Enables integration with predictive maintenance platforms Does not influence protection logic or trip decision pathways FAQ Is this module part of the protection system logic?No. It handles communication and data transfer only and does not participate in protection or voting functions. What software does it support?It is designed for integration with Bently Nevada System 1 condition monitoring software. Can it operate without the TDI front module?No. It functions as the rear interface component and must be paired with the 3500/22 TDI module. What type of data can it transmit?It supports steady-state vibration data, transient waveform data, and system configuration information.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/20 Rack Interface Module
Product Description The Bently Nevada 3500/20 Rack Interface Module (RIM) is the central communication and configuration interface for the 3500 Machinery Protection System. Installed exclusively in Slot 1 of the rack beside the power supply modules, the RIM manages rack configuration, internal communications, system diagnostics, and external data exchange with compatible communication processors. The 3500/20 module acts as the primary gateway between the monitoring rack and external software or supervisory systems. It supports high-speed serial communication and enables access to vibration monitoring data, rack status, event logs, and configuration parameters without interrupting the protection functions of the monitoring system. For Triple Modular Redundant systems, the TMR version of the RIM additionally performs continuous monitor voting and channel comparison functions to improve system reliability in critical rotating equipment applications. The module is engineered for continuous industrial operation in harsh environments including turbine control systems, compressors, generators, pumps, and large process machinery. Key Features Central interface module for Bently Nevada 3500 racks Supports rack configuration and machinery data retrieval Compatible with TDXnet, TDIX, DDIX communication processors Front-panel RS232 communication interface Supports RS232 and RS422 serial communications through I/O modules Integrated system diagnostics and rack status indication TMR-compatible version available for redundant systems Monitor channel comparison and voting functions in TMR applications User-selectable OK relay annunciation logic Designed for continuous machinery protection environments Technical Specifications Parameter Specification Model 3500/20 Product Type Rack Interface Module (RIM) Brand Bently Nevada System Series 3500 Machinery Protection System Rack Position Slot 1 Typical Power Consumption 4.75 W Front Panel Communication RS232 Serial Communication Baud Rate 38.4 kbaud I/O Communication RS232 / RS422 Internal Modem Speed 14.4 kbaud Serial Communication Speed Up to 38.4 kbaud Operating Temperature -30°C to +65°C Storage Temperature -40°C to +85°C Relay Rating 5 A @ 24 VDC / 120 VAC Relay Type Normally Energized Contact Protection Arc Suppression Included Rack Address Capacity 63 Rack Addresses Reset Function Front Panel Rack Reset Button Front Panel Indicators LED Indicator Function OK LED Indicates normal module operation TX/RX LED Shows communication activity within the rack TM LED Indicates Trip Multiply status CONFIG OK LED Confirms valid rack configuration Relay Output Information The integrated OK relay monitors rack operating status and internal fault conditions. Users can configure the relay logic for either open-contact or closed-contact fault annunciation. The relay remains energized during normal operation to improve fault detection reliability. Application Areas The Bently Nevada 3500/20 Rack Interface Module is commonly used in: Steam and gas turbine monitoring systems Compressor protection systems Industrial rotating equipment diagnostics Power generation facilities Oil and gas processing plants Critical machinery shutdown systems Large motor and generator monitoring FAQ What is the function of the 3500/20 Rack Interface Module? The RIM serves as the communication and configuration interface for the entire 3500 monitoring rack. It enables system setup, diagnostic access, and external communication with supervisory systems. Can the 3500 rack operate without the RIM? No. One RIM is required in each 3500 rack because it manages rack-level communications and system configuration functions. Does the RIM affect machinery protection functions? The RIM is not part of the critical monitoring path. Normal monitoring and protection functions continue independently of the RIM. What is the difference between the standard RIM and TMR RIM? The TMR RIM supports Triple Modular Redundant systems and performs monitor voting and channel comparison functions between redundant monitors.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/15-07-07-05(133292-01+133300-01) DC Power Supply Module
Overview The 3500/15-07-07-05 is a low-voltage DC power supply module engineered for Bently Nevada 3500 Series machinery protection systems. Combined with the associated 133292-01 and 133300-01 Power Input Modules (PIMs), the unit converts incoming 24 Vdc-class power into regulated internal DC outputs used by all rack-mounted monitoring modules. The power supply installs into the dedicated left-side supply compartment of the 3500 rack. Systems can be configured with either a single supply or a fully redundant dual-supply arrangement. When two modules are installed, automatic transfer to the backup supply maintains uninterrupted rack operation in the event of a primary supply fault. The matching PIMs are mounted on the rack backplane and provide conditioned DC input handling, fuse protection, surge suppression, and electrical isolation for high-availability industrial environments. Key Features Designed for Bently Nevada 3500 Machinery Protection Racks Compatible with 133292-01 and 133300-01 PIMs Accepts standard 24 Vdc industrial control power Supports redundant power supply configurations Automatic failover capability Hot-swappable during redundant operation Front-panel Supply OK LED indication Integrated isolation and transient protection High-efficiency power conversion design Suitable for PLC panels and low-voltage control systems Electrical Specifications Parameter Specification Model 3500/15-07-07-05 Associated PIMs 133292-01, 133300-01 Input Type Low-Voltage DC Input Voltage Range 20–30 Vdc Nominal Input Voltage 24 Vdc Maximum Rack Current Capacity 11.0 A Output Type Regulated DC Rack Power Efficiency Up to 90% Frequency Requirement DC Input (No Frequency Dependency) Redundancy Support Yes Hot Swap Capability Supported in redundant systems Protection and Isolation Protection Feature Description Surge Protection MOV transient suppression Overvoltage Protection Fuse isolation Undervoltage Condition Non-destructive operation Input-to-Earth Isolation 1500 V Input-to-Output Isolation 500 V Power Conditioning Integrated within PIM EMC Compliance IEC/EN 61000 Series Environmental Specifications Specification Value Operating Temperature -30°C to +65°C Storage Temperature -40°C to +85°C Humidity Rating Up to 95% RH, non-condensing Mechanical Specifications Power Supply Module Parameter Specification Form Factor Half-height module Dimensions 120.7 × 50.8 × 251.5 mm Weight 1.39 kg Typical Applications The 3500/15-07-07-05 low-voltage DC power supply assembly is commonly used in: PLC and DCS control cabinets Turbine monitoring systems Rotating equipment protection systems Petrochemical process plants Compressor monitoring installations Industrial 24 Vdc control networks Continuous machinery condition monitoring systems FAQ What input voltage is required for the 3500/15-07-07-05? The module operates from a 20–30 Vdc input range with a nominal supply voltage of 24 Vdc. What is the function of the 133292-01 and 133300-01 PIMs? These PIMs provide DC input termination, isolation, surge suppression, fuse protection, and power conditioning for the rack power system. Can the module operate in redundant mode? Yes. Two power supplies can be installed for automatic backup operation and increased system availability. Is the module hot-swappable? The module may be replaced during operation when a second redundant supply is installed and active.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/15-05-05-05(106M1079-01+106M1081-01) DC Power Supply Module
Overview The 3500/15-05-05-05 is a high-voltage DC power supply assembly developed for Bently Nevada 3500 Series machinery protection racks. The module receives 88 to 140 Vdc input through the associated 106M1079-01 and 106M1081-01 Power Input Modules (PIMs), then converts the incoming supply into regulated internal DC outputs for all installed rack modules. This power supply occupies the dedicated left-side power compartment of the 3500 rack. Systems may operate with either a single supply or a dual redundant configuration. In redundant operation, one unit functions as the active source while the second remains in standby for automatic failover. The corresponding PIMs mount directly behind the supply on the rack backplane and provide high-voltage input termination, electrical isolation, surge suppression, and fuse protection for critical monitoring environments. Key Features Designed for Bently Nevada 3500 Machinery Protection Systems Compatible with 106M1079-01 and 106M1081-01 PIMs Supports redundant dual-supply architecture Automatic backup switchover during power failure Hot-swappable in redundant installations Front-panel “Supply OK” LED indication Integrated isolation and transient suppression Optimized for high-reliability industrial monitoring systems Suitable for substation and power generation applications Electrical Specifications Parameter Specification Model 3500/15-05-05-05 Associated PIMs 106M1079-01, 106M1081-01 Input Type High-Voltage DC Input Voltage Range 88–140 Vdc Nominal Input Voltage 125 Vdc Frequency Requirement DC Input (No Frequency Dependency) Maximum Rack Output Capacity 2.5 A Output Type Regulated Internal DC Conversion Efficiency Up to 90% Redundancy Support Yes Hot Swap Capability Supported in redundant systems Protection and Isolation Protection Feature Description Surge Suppression MOV transient protection Overvoltage Protection Internal fuse isolation Undervoltage Protection Non-destructive operation Input-to-Earth Isolation 1500 V Input-to-Output Isolation 500 V EMC Compliance IEC/EN 61000 Series Environmental Ratings Specification Value Operating Temperature -30°C to +65°C Storage Temperature -40°C to +85°C Humidity Up to 95% RH, non-condensing Mechanical Specifications Power Supply Module Parameter Specification Form Factor Half-height module Dimensions 120.7 × 50.8 × 251.5 mm Weight 1.39 kg Typical Applications The 3500/15-05-05-05 high-voltage DC power supply system is commonly installed in: Electrical substations Turbine monitoring systems HVDC control environments Power generation facilities Compressor and pump monitoring systems Petrochemical process plants Continuous machinery protection installations FAQ What is the purpose of the 106M1079-01 and 106M1081-01 PIMs? These PIMs provide DC input connection, surge suppression, fuse protection, and electrical isolation between the external supply and the rack power system. Can the module support redundant power operation? Yes. Two power supplies can be installed in the same rack for automatic failover redundancy. Is the module hot-swappable? The power supply can be replaced while the rack remains operational if a second redundant supply is installed. What type of input power does the module require? The unit operates from an 88–140 Vdc high-voltage DC input with a nominal operating level of 125 Vdc.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/15-01-01-00 125840-02 AC Power Supply Module
Overview The 3500/15-01-01-00 is a low-voltage AC power supply module engineered for the Bently Nevada 3500 Machinery Protection platform. Working together with the 125840-02 Power Input Module (PIM), the unit converts incoming AC power into regulated internal DC outputs required for rack operation and module stability. This power supply is mounted in the dedicated left-side section of the 3500 rack and supports both standalone and redundant operating configurations. In dual-supply systems, the modules function in automatic primary and backup mode to maintain uninterrupted rack power during maintenance or power module failure. The matching 125840-02 PIM is mounted directly behind the supply on the rack backplane and manages AC input connection, transient suppression, and input fuse protection. Key Features Designed for Bently Nevada 3500 Series protection racks Compatible with 125840-02 low-voltage AC PIM Supports redundant dual-power operation Automatic switchover between primary and backup supplies Hot replacement capability in redundant systems Front-panel “Supply OK” LED indication Integrated surge suppression and overvoltage protection Stable regulated DC output for rack modules Technical Specifications Parameter Specification Model 3500/15-01-01-00 Associated PIM 125840-02 Product Type Low-Voltage AC Power Supply Input Type Low-Voltage AC Input Voltage Range 85–132 Vac RMS Nominal Input Voltage 110 Vac Peak Voltage Range 120–187 Vac Peak Input Frequency 47–63 Hz Maximum Rack Capacity 4.5 A RMS Output Type Regulated DC Rack Power Redundant Operation Supported Hot Swap Capability Yes, with redundant supply installed Status Indicator Supply OK LED Protection and Reliability Protection Function Description Surge Protection MOV transient suppression Overvoltage Protection Input fuse isolation Undervoltage Condition No damage to supply or PIM EMC Compliance IEC/EN 61000 Series Environmental Specifications Specification Value Operating Temperature -30°C to +65°C Storage Temperature -40°C to +85°C Humidity Up to 95% non-condensing Mechanical Specifications Power Supply Module Parameter Specification Form Factor Half-height module Dimensions 120.7 × 50.8 × 251.5 mm Weight 1.39 kg Application Areas The 3500/15-01-01-00 power supply assembly is commonly used in continuous monitoring systems for: Gas and steam turbines Industrial compressors Rotating machinery monitoring Petrochemical production systems Power generation facilities Pipeline and oil processing equipment Critical plant protection installations FAQ What is the function of the 125840-02 PIM? The 125840-02 Power Input Module provides AC input termination, surge suppression, and fuse protection for the connected power supply module. Can the power supply be replaced while the rack is operating? Yes. In redundant configurations, the module supports hot-swapping without interrupting rack operation. How many power supplies can be installed in one rack? The 3500 rack supports either a single power supply or a dual redundant configuration using two modules. What output does the module provide to the rack? The module converts incoming AC power into regulated DC voltages distributed across all installed rack modules.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/15-01-01-00 AC Power Supply Module
Overview The 3500/15-01-01-00 is a low-voltage AC power supply designed for the Bently Nevada 3500 Series Machinery Protection System. This half-height module installs into the dedicated power supply section on the left side of the rack and delivers regulated operating power to all installed monitoring and communication modules. The module operates together with a compatible Low-Voltage AC Power Input Module (PIM), accepting standard industrial AC input and converting it into stable internal DC voltages required by the rack system. The 3500 rack supports either a single power supply configuration or a redundant arrangement with dual supplies. In redundant mode, the lower position functions as the primary supply while the upper position acts as the backup source. Power modules can be replaced during operation without shutting down the rack when redundancy is configured. Key Features Compatible with Bently Nevada 3500 Series racks Supports redundant power supply architecture Hot-swappable in dual-supply installations Front-panel “Supply OK” LED indication Designed for continuous industrial monitoring applications Integrated protection against undervoltage and input abnormalities Stable output distribution to all rack modules Technical Specifications Parameter Specification Model Number 3500/15-01-01-00 Product Type Low-Voltage AC Power Supply Module Series 3500 Series Input Voltage Range 85 to 132 Vac RMS Nominal Input Voltage 110 Vac Input Frequency 47 to 63 Hz Maximum Rack Load Current 4.5 A RMS Operating Temperature -30°C to +65°C Storage Temperature -40°C to +85°C Humidity Rating 95% RH, non-condensing Status Indication Front-panel LED Module Mounting Left-side rack power supply slot Redundancy Support Yes Hot Swap Capability Supported in redundant configuration Power Supply Module Dimensions Item Specification Height 120.7 mm Width 50.8 mm Depth 251.5 mm Weight 2.70 lbs System Protection Characteristics Protection Function Response Undervoltage Condition No damage to module or PIM Overvoltage Condition PIM input fuse protection activates Application Areas The 3500/15-01-01-00 power supply module is commonly deployed in critical rotating equipment monitoring systems including: Steam and gas turbines Compressors Pumps and motors Oil and gas process plants Power generation facilities Petrochemical monitoring systems Heavy industrial machinery protection racks FAQ Can the module operate in a redundant power configuration? Yes. The 3500 rack supports dual power supplies for redundancy. If one module fails, the secondary supply automatically maintains rack operation. Is the power supply hot-swappable? The module can be inserted or removed without interrupting system operation when a second redundant supply is installed and active. What input voltage does the module require? The unit accepts 85–132 Vac RMS input with a nominal operating voltage of 110 Vac. Which racks are compatible with this module? The module is intended for use with Bently Nevada 3500 Series Machinery Protection System racks equipped with the corresponding low-voltage AC PIM.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/15 125840-01 AC Power Input Module
Product Description The 3500/15 125840-01 High Voltage AC Power Input Module is engineered for use with the Bently Nevada 3500 Machinery Protection platform. Installed behind the associated 3500/15 power supply module, this Power Input Module (PIM) accepts high-voltage AC mains input and delivers conditioned power to the rack power supply system. Designed for continuous-duty industrial applications, the Bently Nevada 125840-01 supports reliable operation of monitoring and protection modules installed within 3500 rack assemblies. The module operates with nominal 220 Vac systems and accommodates a wide AC input range, making it suitable for power generation plants, petrochemical facilities, turbine monitoring systems, and heavy rotating equipment installations. The module supports both standalone and redundant power supply architectures. In dual-supply configurations, the PIM enables automatic failover functionality and uninterrupted rack operation during maintenance or module replacement procedures. Hot-swappable capability allows service technicians to replace a module without shutting down the entire monitoring system when redundant power is available. Its compact half-height design simplifies rack integration while maintaining high conversion efficiency and stable power conditioning performance under varying industrial load conditions. Technical Specifications Parameter Specification Model Number 3500/15 Part Number 125840-01 Manufacturer Bently Nevada Product Type High Voltage AC Power Input Module Product Series 3500 Machinery Protection System Compatible Module 3500/15 Power Supply Installation Type Backplane Mounted Module Format Half-Height Redundancy Support Yes Hot Swap Capability Supported Rack Compatibility 3500 Rack Systems Electrical Specifications Parameter Value Nominal Input Voltage 220 Vac Input Voltage Range 175–264 Vac RMS Peak Voltage Range 247–373 Vac Peak Frequency Range 47–63 Hz Maximum Output Current 2.3 A RMS Conversion Efficiency Up to 90% Protection Features Overvoltage fuse protection Undervoltage tolerance without module damage Stable conditioned power delivery Automatic redundant power switchover support Industrial-grade electrical isolation and protection design Environmental Specifications Parameter Specification Operating Temperature -30°C to +65°C Storage Temperature -40°C to +85°C Relative Humidity 0–95% Non-Condensing Mechanical Specifications Parameter Value Dimensions 120.7 × 25.4 × 114.3 mm Weight 0.34 kg Mounting Method Rack Backplane Installation Functional Characteristics The 125840-01 module performs incoming AC conditioning for the associated 3500/15 power supply and distributes stable operating power throughout the rack system. The design supports: High-voltage AC input applications Dual power supply redundancy Continuous monitoring system uptime Simplified maintenance through hot-swappable installation Compact integration into standard 3500 racks Typical Applications This module is commonly used in: Steam turbine monitoring systems Gas compressor protection systems Generator vibration monitoring Industrial motor protection applications Oil and gas production facilities Refinery process monitoring systems Critical rotating equipment installations FAQ What is the purpose of the 125840-01 module? The module conditions high-voltage AC input power for the compatible 3500/15 rack power supply within the 3500 Machinery Protection System. Can the module be replaced during operation? Yes. When a redundant power supply configuration is installed, the module supports hot-swappable replacement without interrupting rack operation. Is the module compatible with all 3500 racks? The module is designed for compatible Bently Nevada 3500 rack systems using the 3500/15 power supply assembly.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/15 106M1081-01 Universal AC Power Input Module
Product Description The 106M1081-01 Universal AC Power Input Module is designed for integration with the Bently Nevada 3500/15 power supply assembly within the 3500 Machinery Protection System. This module conditions incoming AC mains power and delivers stabilized input power to the associated 3500/15 power supply module for rack-wide distribution. Engineered for continuous industrial operation, the Bently Nevada 106M1081-01 supports a broad universal AC voltage range without requiring manual jumper configuration or input selection adjustments. The module installs directly behind the corresponding 3500/15 power supply in the left section of the rack chassis. For high-availability applications, the module supports redundant power configurations. When dual Power Input Modules and dual power supplies are installed, the system automatically balances the electrical load while enabling uninterrupted failover during maintenance or power supply replacement procedures. The module incorporates surge suppression, isolation protection, and low leakage current characteristics to support reliable operation in critical machinery monitoring environments including turbine control systems, compressor trains, process plants, and power generation facilities. Technical Specifications Parameter Specification Model Number 106M1081-01 Manufacturer Bently Nevada Product Type Universal AC Power Input Module Compatible Power Supply 3500/15 Product Series 3500 Machinery Protection System Installation Position Rear of 3500/15 Power Supply Rack Compatibility 3500 Rack Systems Redundancy Support Yes Hot Swap Capability Supported Protection Rating IP20 Cooling Method Passive Cooling Electrical Input Specifications Parameter Value Input Voltage Range 85–264 Vac RMS Frequency Range 47–63 Hz Peak Voltage Tolerance 120–373 Vac Peak Inrush Current Less than 25 A Peak Inrush Duration Less than 5 ms Surge Protection MOV and Gas Tube Protection Filtering Method Differential-Mode Choke Isolation Ratings Isolation Type Rating Input to Earth 1.5 kVac Input to Output 500 Vdc Power Handling Performance The 106M1081-01 module supports the associated 3500/15 power supply with rack current capability up to 2.8 A RMS at 240 Vac input conditions. Integrated protection functions include: Undervoltage protection without module damage Fuse-based overvoltage isolation Automatic load sharing in redundant systems Seamless failover operation during maintenance Environmental Specifications Parameter Specification Operating Temperature -30°C to +65°C Storage Temperature -40°C to +85°C Relative Humidity 95% Non-Condensing Mechanical Specifications Parameter Value Dimensions 120.7 × 25.4 × 114.3 mm Weight 0.34 kg Connector Type IEC C14 Inlet Rack Connection Crimp Fork Terminal Interface Functional Features Universal AC input without voltage selection jumpers Hot-swappable during redundant operation Compatible with dual power supply redundancy architectures Front-panel status indication LEDs Integrated monitoring support through 3500/20 Rack Interface Module High surge immunity compliant with IEC 61000-4-5 Low leakage current for sensitive protection systems Typical Applications The Bently Nevada 106M1081-01 module is commonly deployed in: Steam turbine monitoring systems Gas compressor protection platforms Boiler feedwater pump monitoring Heavy-duty industrial motor protection Offshore production facilities Rotating machinery condition monitoring Nuclear plant auxiliary pump systems FAQ What is the function of the 106M1081-01 module? The module conditions and distributes universal AC input power to the compatible 3500/15 power supply within the 3500 rack system. Can the module be replaced while the rack is operating? Yes. In redundant configurations, the module supports hot-swapping without interrupting rack operation. Does the module support automatic failover? Yes. Dual-module installations provide automatic load sharing and seamless backup operation if one supply path becomes unavailable.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/15 Power Supply Module for 3500 Rack
Product Description The Bently Nevada 3500/15 power supply module is designed for use within the 3500 Machinery Protection System, delivering regulated operating power to monitoring and protection modules installed in the rack. The unit supports universal AC input, high-voltage DC input, and low-voltage DC input configurations depending on the associated Power Input Module (PIM). As a rack-mounted half-height module, the 3500/15 installs in the dedicated left-side power supply slots of the 3500 rack assembly. The module converts external incoming power into stabilized internal voltages required by vibration monitoring, relay, communication, and protection modules throughout the system. The power supply supports both standalone and redundant configurations. In dual-supply installations, the lower module operates as the primary source while the upper module functions as backup redundancy. This arrangement enables uninterrupted rack operation during module replacement or power source failure when the secondary supply remains active. Designed for continuous industrial operation, the module is widely used in turbine monitoring systems, compressor protection platforms, petrochemical facilities, power generation plants, and critical rotating equipment applications where high system availability is required. Technical Specifications Parameter Specification Model 3500/15 Manufacturer Bently Nevada Product Type Power Supply Module Product Series 3500 Machinery Protection System Module Format Half-Height Rack Module Installation Position Left Side of 3500 Rack Redundancy Support Yes Rack Compatibility 3500/05 Rack Systems Supported Configurations Single or Dual Redundant Cooling Method Passive Internal Cooling Operating Mode Continuous Duty Input Voltage Specifications Input Type Electrical Range Universal AC Input 85–264 Vac RMS Hazardous Area AC Range 85–250 Vac RMS AC Frequency 47–63 Hz Peak AC Input 120–373 Vac Peak High Voltage DC Input 88–140 Vdc Low Voltage DC Input 20–30 Vdc Current Capacity Power Configuration Maximum Current Universal AC Supply 2.8 A RMS High Voltage DC Supply 2.5 A Low Voltage DC Supply 11.0 A Protection Features Integrated undervoltage protection Overvoltage protection through Power Input Module fuse isolation Continuous rack power support during redundant supply switchover Stable voltage regulation for critical monitoring modules Environmental Specifications Parameter Value Operating Temperature -30°C to +65°C Relative Humidity 95% Non-Condensing System Compatibility The Bently Nevada 3500/15 module operates with compatible Power Input Modules designed for specific AC or DC input types. Universal AC versions are not interchangeable with legacy AC PIM assemblies, while high-voltage and low-voltage DC variants require matching DC PIM configurations. Mixed legacy and updated module/PIM combinations may be installed within the same rack if properly matched according to system configuration requirements. Application Areas Typical installations include: Steam and gas turbine monitoring Compressor protection systems Power generation facilities Oil and gas processing plants Rotating equipment monitoring Process control protection systems Industrial vibration monitoring networks FAQ Can the 3500/15 operate in redundant mode? Yes. Two power supply modules may be installed in one rack for automatic redundancy. The backup supply maintains rack operation if the primary module is removed or fails. Which rack systems support the 3500/15 module? The module is designed for use with compatible 3500/05 rack assemblies, including 19-inch rack and bulkhead mounting configurations. Does the module support both AC and DC input power? Yes. Depending on the selected Power Input Module, the unit supports universal AC, high-voltage DC, or low-voltage DC input operation.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/05-02-05-00-00-01 Mini Bulkhead Rack 7 Slot Unit
Product Overview The 3500/05-02-05-00-00-01 is a compact configuration within the Bently Nevada 3500 machinery protection platform, engineered for installations where space efficiency and front-access wiring are required. It combines a reduced 7-slot chassis with a bulkhead mounting structure, enabling direct cabinet or wall integration while maintaining full system compatibility. This rack provides the structural foundation, power routing, and backplane communication required for continuous machinery monitoring and protection in API 670–compliant environments. Configuration Definition This model is defined by the following system layout: Mini rack frame with 7 module positions Bulkhead mounting design with front-side wiring access Standard non-barrier backplane architecture No internal isolation barriers included Standard EIA mechanical finish specification Mechanical Construction Rack type: Mini-size 3500 chassis Mounting method: Bulkhead installation (front-access wiring layout) Frame material: Industrial-grade aluminum alloy Approximate dimensions: Height: ~178 mm (7 in) Width: 305 mm (12 in) Depth: ~305 mm (12 in) Service design: Wiring and termination accessible from front panel This structure is optimized for compact enclosures and wall-mounted protection systems where rear access is restricted. Module Capacity & Layout The internal architecture supports essential monitoring system components: Dedicated slots for system-critical modules: Rack Interface Module (RIM) Power supply unit Remaining slots available for: Vibration monitoring modules Relay interface modules Communication modules Total capacity is limited to 7 modules to maintain compact system design. Electrical & Backplane System Backplane type: Standard non-barrier configuration Power architecture: Supports single or redundant power supply operation Communication paths: System data bus Relay signal bus Keyphasor and transducer routing channels Full compatibility with standard Bently Nevada 3500 modules (within slot limit) Designed for continuous machinery protection operation Environmental Performance Operating temperature range: –20°C to +65°C Storage temperature range: –40°C to +85°C Humidity tolerance: up to 95% non-condensing Suitable for vibration-intensive industrial environments including rotating machinery systems Compliance & Safety Standards EMC immunity: EN 61000-6-2 EMC emissions: EN 61000-6-4 Electrical safety: EN 61010-1 Hazardous area certifications: Class I, Division 2, Groups A–D, T4 ATEX / IECEx Zone 2 (non-barrier configuration) Application Scenarios Compact turbine and compressor protection systems Skid-mounted rotating equipment monitoring OEM machinery with integrated condition monitoring Wall-mounted or cabinet-based installations requiring front wiring access Small-footprint industrial protection systems FAQ Q1: What is the key advantage of bulkhead mounting?It allows all wiring connections to be accessed from the front, eliminating rear clearance requirements. Q2: How many modules can be installed in this rack?The rack supports up to 7 modules including RIM and power supply positions. Q3: Is it compatible with all 3500 modules?Yes, it supports standard 3500 series modules within its slot capacity.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/05-02-04-00-00-01 Mini Rack PLC Chassis System
Product Overview The 3500/05-02-04-00-00-01 is a compact, rack-mount chassis from Bently Nevada’s 3500 machinery protection series. Designed for installations where space is limited, this mini-rack accommodates up to seven modules, providing the structural frame and electrical backplane for continuous machinery protection. Its rear-access wiring configuration simplifies installation in control cabinets and skid-mounted equipment. This chassis supports full integration of Rack Interface Modules (RIM), power supplies, monitors, relays, and communication modules, ensuring complete API‑670-compliant vibration monitoring for small-footprint systems. Technical Specifications Rack Format Type: Mini 3500 rack Mounting: 19-inch EIA rails, rack-mount Module slots: 7 total Reserved positions: 1 for RIM, 1 for power supply Remaining slots for monitors, relays, or communications Mechanical Dimensions: 178 mm H × 305 mm W × 305 mm D (~7 × 12 × 12 in) Material: Aluminum chassis Finish: Standard EIA (option 01) Wiring access: Rear Backplane / Electrical Type: Standard non-barrier Power: Single or dual redundant supply support Communication buses: System data bus, relay bus, Keyphasor and transducer routing Module compatibility: All standard 3500 series modules (within slot limits) Environmental Ratings Operating temperature: –20°C to +65°C Storage temperature: –40°C to +85°C Humidity: Up to 95% non-condensing Vibration: Industrial-grade, suitable for turbines, compressors, and refinery machinery Certifications EMC: EN 61000‑6‑2 (immunity), EN 61000‑6‑4 (emissions) Safety: EN 61010‑1 Hazardous area: Class I, Div 2, Groups A–D, T4; ATEX/IECEx Zone 2 Applications Compact turbine or compressor protection systems Skid-mounted machinery monitoring OEM equipment requiring integrated protection Small-footprint monitoring and condition-based maintenance Option Code Breakdown 02 — Mini-rack (7 slots) 04 — Rack-mount format 00 — Standard non-barrier backplane 00 — No internal barriers 01 — Standard EIA finish FAQ Q1: Can this mini-rack be installed in a standard 19-inch cabinet?Yes, it is designed for 19-inch EIA rail mounting with rear wiring access. Q2: How many modules can this mini-rack accommodate?Up to seven modules: 1 RIM, 1 power supply, and 5 for monitors, relays, or communication modules. Q3: Is it suitable for harsh industrial environments?Yes, it supports industrial vibration, temperature extremes, and electrical isolation for reliable monitoring.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/05-02-04-00-00-00 System Rack Chassis
System Overview The 3500/05-02-04-00-00-00 is a compact rack assembly within the Bently Nevada 3500 protection platform. It is engineered for installations where cabinet space is limited but full machinery protection functionality is still required. The unit integrates mechanical housing, electrical backplane routing, and modular power distribution in a reduced 7-slot configuration. This mini rack maintains full compatibility with the 3500 system architecture while reducing footprint compared to standard 14-slot chassis designs. Configuration Definition This model is defined by the following structure: Mini rack chassis with 7 module positions 19-inch rack-mount installation format Standard non-barrier backplane architecture No internal isolation barriers included Standard finish configuration The design supports compact system integration without compromising signal integrity or system reliability. Mechanical Construction Rack type: Mini-size 3500 chassis Mounting style: Rack-mount (EIA 19-inch rails) Construction material: Industrial-grade aluminum alloy Approximate dimensions: Height: ~178 mm (7 in) Width: 305 mm (12 in) Depth: ~305 mm (12 in) Service access: Rear wiring access for rack-mounted cabinet installations The reduced frame size is optimized for skid systems and compact enclosures. Module Capacity & Layout Internal slot structure supports essential system components: Dedicated slots for: Rack Interface Module (RIM) Power supply module Remaining slots available for: Vibration monitoring modules Relay modules Communication interface modules Total usable capacity: 7 modules maximum Electrical Architecture Backplane type: Standard non-barrier configuration Power input: Supports single or redundant power supply operation Internal buses: System communication data bus Relay output bus Keyphasor and transducer signal routing channels Full compatibility with standard Bently Nevada 3500 module range (within slot limitation) Designed for continuous machinery protection applications Environmental Performance Operating temperature: –20°C to +65°C Storage temperature: –40°C to +85°C Relative humidity: up to 95% non-condensing Designed for vibration-prone industrial environments including rotating machinery systems Standards & Compliance EMC immunity: EN 61000-6-2 EMC emissions: EN 61000-6-4 Electrical safety: EN 61010-1 Hazardous area approvals: Class I, Division 2, Groups A–D, T4 ATEX / IECEx Zone 2 (non-barrier configuration) Typical Applications Compact turbine protection systems Skid-mounted compressors and rotating equipment OEM machinery with integrated monitoring requirements Small cabinet or space-constrained industrial installations Distributed condition monitoring systems requiring reduced footprint FAQ Q1: How does this mini rack differ from full-size 3500 racks?It provides 7 module slots instead of 14, making it suitable for compact installations. Q2: Can it support redundant power supplies?Yes, within slot allocation limits, redundant power configurations are supported. Q3: Is it compatible with all 3500 modules?Yes, standard modules are supported as long as system slot capacity is not exceeded.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/05-01-03-05-00-01 System Rack Chassis
System Overview The 3500/05-01-03-05-00-01 is a full-capacity chassis designed for the Bently Nevada 3500 machinery protection architecture. It functions as the central structural platform that houses all monitoring, relay, communication, and power modules while enabling system-wide communication and regulated power distribution through an integrated backplane. This configuration is specifically engineered for installations requiring front-side wiring access, making it suitable for wall-mounted or cabinet-integrated protection systems. Configuration Definition This rack variant is defined by the following configuration structure: Full-size chassis with 14 module positions Bulkhead-mount installation format with front-access wiring design Standard non-barrier backplane architecture No internal isolation barriers included Standard EIA finish and mechanical specification Mechanical Construction & Access Design Rack format: 19-inch EIA full-size chassis Mounting style: Bulkhead installation with front-access wiring layout Frame material: Industrial-grade aluminum alloy Nominal dimensions: Height: ~266 mm Width: 483 mm Depth: ~305 mm Serviceability: All field wiring connections accessible from the front panel This design reduces rear clearance requirements and simplifies cabinet integration in constrained installations. Module Layout & Slot Allocation The internal slot architecture supports structured system configuration: Dedicated positions for core system modules: Rack Interface Module (RIM) Redundant or single power supply units Remaining slots configured for: Vibration monitoring modules Relay modules Communication interface modules The layout ensures stable communication across all installed modules via the system backplane. Electrical & Backplane System Backplane type: Standard non-barrier design Power architecture: Supports redundant or single power supply configurations Communication infrastructure: System data bus Relay signal bus Keyphasor and transducer signal routing channels Full compatibility with standard Bently Nevada 3500 module range Designed for continuous machinery protection in API 670-compliant systems Environmental & Operating Limits Operating temperature range: –20°C to +65°C Storage temperature range: –40°C to +85°C Humidity tolerance: Up to 95% non-condensing Mechanical resilience: Suitable for vibration-intensive industrial environments Standards & Certifications EMC immunity: EN 61000-6-2 EMC emissions: EN 61000-6-4 Electrical safety: EN 61010-1 Hazardous area approvals: Class I, Division 2, Groups A–D, T4 ATEX / IECEx Zone 2 (non-barrier configuration) Typical Application Areas Turbine protection and monitoring systems Compressor and rotating equipment diagnostics Refinery and petrochemical plant machinery protection Power generation monitoring systems Wall-mounted or cabinet-integrated 3500 system installations requiring front wiring access FAQ Q1: What is the main advantage of bulkhead mounting?It allows all wiring connections to be accessed from the front, reducing rear clearance requirements. Q2: Can this rack support all 3500 modules?Yes. It is compatible with standard Bently Nevada 3500 monitoring, relay, and communication modules. Q3: Is internal barrier protection included?No. This configuration uses a standard non-barrier backplane design.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/05-01-02-05-00-01 Rack Chassis
Overview The 3500/05-01-02-05-00-01 is a full-size rack-mount chassis for the Bently Nevada 3500 Machinery Protection System. It provides the physical frame, power distribution, and backplane communication required to integrate all monitoring, relay, communication, and power modules into a complete machinery protection setup. This configuration features a standard, non-barrier backplane and supports panel- and rail-mounted industrial installations. Configuration Details This order code specifies the rack configuration: Full-size 14-slot frame Rack-mount design compatible with 19-inch EIA rails Standard non-barrier backplane No internal barriers installed Standard EIA finish and aluminum chassis The design ensures modular flexibility for a wide range of protection and monitoring modules. Mechanical & Dimensional Specifications Rack Type: Full-size 3500 series chassis Mounting: Rack-mount (19-inch EIA rails) Total Module Slots: 14 Reserved Slots: 1 for Rack Interface Module (RIM), 1–2 for power supply modules Remaining Slots: Flexible for monitors, relays, or communication modules Chassis Material: Aluminum Finish: Standard EIA Dimensions: Height: ~266 mm (10.5 in) Width: 483 mm (19 in) Depth: ~305 mm (12 in) Electrical & Backplane Architecture Backplane Type: Standard non-barrier Power Distribution: Supports single or dual redundant supplies Communication Buses: System data bus Relay bus Keyphasor and transducer signals Module Compatibility: All standard 3500 series modules Designed for continuous API-670-compliant machinery protection Environmental & Compliance Ratings Operating Temperature: –20°C to +65°C Storage Temperature: –40°C to +85°C Relative Humidity: Up to 95% non-condensing Vibration: Industrial-grade, turbine/compressor compatible EMC: EN 61000-6-2 (immunity), EN 61000-6-4 (emissions) Electrical Safety: EN 61010-1 Hazardous Area Approvals: Class I, Div 2, Groups A–D, T4; ATEX / IECEx Zone 2 Applications Gas and steam turbine protection systems Compressor and critical rotating machinery monitoring Refinery and petrochemical equipment protection Power generation machinery Any installation requiring a complete 3500 system rack infrastructure Option Code Breakdown 01 — Full-size rack (14 slots) 02 — Rack-mount format 05 — Standard backplane 00 — No internal barriers 01 — Standard finish FAQ Q1: Can internal barrier modules be installed in this rack?No. This rack is configured with a standard non-barrier backplane. Q2: How many modules can the rack support?Up to 14 module positions including reserved slots for RIM and power supply modules. Q3: Is this rack compatible with all 3500 modules?Yes. It supports all standard 3500 series modules for monitoring, relay, and communication functions.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/05-01-01-05-00-01 System Rack Chassis
Overview The 3500/05-01-01-05-00-01 is a full-capacity rack assembly within the Bently Nevada 3500 monitoring platform. It serves as the central physical and electrical foundation for installing and linking all system modules used in machinery protection applications. This configuration represents a standard, non-barrier, panel-mounted 14-slot rack equipped with a unified backplane architecture for signal exchange and power distribution across all installed modules. Configuration Definition This specific order code defines the rack characteristics as follows: Full-size rack frame with 14 available module slots Panel-mounted installation design Standard backplane architecture without internal isolation barriers Non-barrier system configuration for general industrial environments Standard finish and mechanical build specification Mechanical Design Rack format: 19-inch EIA-compatible chassis Installation type: Panel mounting with rear service access Construction material: High-strength aluminum alloy frame Nominal dimensions: Height: 266 mm Width: 483 mm Depth: 305 mm Modular slot layout designed for flexible system expansion The structure is optimized for continuous operation in vibration-prone environments typical of rotating machinery installations. Slot Allocation & System Layout The internal architecture supports structured module placement: Dedicated slots for system-critical components Rack Interface Module (RIM) Redundant power supply modules Remaining positions available for: Vibration monitoring modules Relay interface modules Communication and diagnostic modules The backplane ensures synchronized communication across all installed modules. Electrical Architecture Integrated system backplane for high-speed data exchange Distributed power bus supporting redundant power input Signal routing for Keyphasor, transducer, and relay logic channels Fully compatible with standard Bently Nevada 3500 module family Designed for continuous monitoring and protection system operation Environmental Performance Operating temperature range: –20°C to +65°C Storage range: –40°C to +85°C Relative humidity tolerance: up to 95% non-condensing Mechanical robustness aligned with industrial vibration standards Compliance & Safety Standards EMC immunity: EN 61000-6-2 EMC emissions: EN 61000-6-4 Electrical safety: EN 61010-1 Hazardous area certification: Class I, Division 2, Groups A–D, T4 ATEX / IECEx Zone 2 (non-barrier configuration) System Integration Notes Designed for integration with all standard 3500 series modules Requires correct placement of RIM and power modules in designated slots Backplane supports system-wide diagnostics and communication integrity checks Compatible with standard rack-based 3500 system architecture Typical Applications Gas and steam turbine protection systems Compressor condition monitoring installations Refinery and petrochemical equipment protection Power generation rotating machinery systems Large-scale multi-channel machinery monitoring platforms FAQ Q1: Is this rack suitable for internal barrier modules?No. This configuration is a non-barrier system rack and is not designed for internal isolation modules. Q2: How many modules can be installed?The rack supports 14 module positions, including slots reserved for RIM and power supplies. Q3: Can it be upgraded after installation?Yes. Additional modules can be added as long as slot capacity and power budget are maintained.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/05 System Rack | 14 Slot EIA Rack Unit
Overview The 3500/05 system rack from Bently Nevada serves as the structural and electrical backbone of the 3500 Machinery Protection System. It is responsible for mechanically supporting all monitoring modules while ensuring stable power delivery and high-speed internal communication through a dedicated backplane architecture. This rack does not perform signal processing itself; instead, it provides the platform required for all 3500 system modules to operate as an integrated protection and monitoring system. Mechanical Structure & Configuration The rack is engineered in two standardized formats to support different installation requirements: Full-size rack (19-inch EIA) Supports up to 14 module slots Designed for standard industrial control cabinet integration Provides full rear access for wiring and maintenance Mini rack (12-inch format) Supports up to 7 module slots Compact design for space-constrained installations Rear wiring access maintained for serviceability Mini rack configurations are not compatible with bulkhead mounting arrangements. Mounting Options The system rack supports multiple installation methods depending on site design: Panel mounting using rectangular cut-outs with rear access wiring Standard 19-inch rack mounting on EIA rails Bulkhead mounting with front-access wiring for tight enclosures Each mounting method is selected based on cabinet architecture and maintenance accessibility requirements. Electrical Architecture Integrated backplane for module-to-module communication Centralized power distribution through installed power supplies Left-side reserved slots for system-critical modules: Rack Interface Module (RIM) Power supply units Remaining slots are configurable for vibration monitors, relay modules, and communication interfaces within the 3500 platform. Environmental & Compliance Standards Operating temperature range: –20°C to +65°C EMC compliance: EN 61000-6-2 (industrial immunity) EN 61000-6-4 (industrial emissions) Electrical safety standard: EN 61010-1 FCC Part 15 compliance for electromagnetic regulation Hazardous Area Certifications The rack is suitable for deployment in classified environments when used with approved system components: Class I, Division 2, Groups A–D, T4 ATEX / IECEx: II 3G Ex nA nC ic IIC T4 Gc System Integration Notes Internal barrier configurations require dedicated grounding via 3500/04-01 earthing module Mini rack configurations require compatible system software version 2.70 or later Some display and enclosure accessories may have compatibility constraints depending on rack type Application Areas Gas and steam turbine protection systems Compressor and rotating equipment monitoring Refinery and petrochemical machinery infrastructure Power generation condition monitoring systems Large-scale machinery protection architectures requiring modular expansion FAQ Q1: Does the 3500/05 perform vibration measurement?No. It functions purely as a rack platform for housing and interconnecting monitoring modules. Q2: Can different module types be mixed in one rack?Yes. The rack supports mixed configurations of monitors, relays, and communication modules within available slots. Q3: Is the rack expandable after installation?Yes. System expansion is supported as long as slot capacity and power budget are respected.
$200.00 $100.00
-
Bently Nevada Bently Nevada 3500/01-01 Rack Config Software Manual System
Overview The 3500/01-01 from Bently Nevada is a configuration software package and system manual designed for the Bently Nevada 3500 machinery protection and condition monitoring platform. It is used during system commissioning, expansion, and maintenance to define rack architecture, module assignments, and alarm logic settings. Unlike measurement modules, this product does not perform signal acquisition or vibration analysis. Instead, it provides the engineering environment required to configure and manage the 3500 monitoring rack. System Functionality Rack-level configuration for Bently Nevada 3500 monitoring systems Module slot assignment and system topology definition Channel configuration for connected monitoring modules Alarm threshold setup and logical grouping Support for system commissioning and reconfiguration Documentation-driven setup guidance for engineering teams Software & Documentation Scope PC-based configuration utility for 3500 rack setup Engineering manual included for installation and system logic reference Used in conjunction with 3500 series hardware modules Supports structured configuration of multi-channel monitoring systems Facilitates system expansion and maintenance planning Technical Characteristics Platform: Bently Nevada 3500 Series system environment Purpose: Rack configuration and system setup (non-measurement function) Deployment: Engineering workstation (Windows-based environment) Output: Configuration data for rack and module initialization Compatibility: Full integration with 3500 monitoring hardware family Application Scenarios Commissioning of new 3500 rack monitoring systems Reconfiguration after system expansion or module replacement Maintenance and lifecycle updates of installed monitoring racks Engineering validation of system architecture prior to startup FAQ Q1: Does this product measure vibration or process signals?No. It is strictly a configuration tool and manual for system setup, not a measurement module. Q2: Is it required for installing a Bently Nevada 3500 system?Yes. It is typically used during initial commissioning and system configuration stages. Q3: Can it be used for all 3500 series racks?It is designed for compatibility across the Bently Nevada 3500 rack platform and its supported modules.
$200.00 $100.00
-
Bently Nevada Bently Nevada 140482-01 Velom I/O Module
Overview The 140482-01 Velom I/O Module from Bently Nevada’s 3300 series delivers high-precision vibration sensing for rotating machinery. Engineered for industrial reliability, this module supports real-time monitoring and early fault detection across turbines, compressors, and motors. Technical Specifications Specification Details Model Number 140482-01 Manufacturer Bently Nevada Product Series 3300 Module Type Velom I/O Module Dimensions 2.5 x 11 x 24 cm Weight 0.4 kg System Compatibility TSI Communication Interface Ethernet Router HS Code 8537101190 Product Origin USA Condition Brand New Lead Time In Stock MOQ 1 Discontinued Status Active Key Features The 140482-01 module integrates seamlessly with Bently Nevada’s monitoring systems. Its seismic sensing capability ensures accurate vibration data for predictive maintenance. The rugged 2.5x11x24 cm housing withstands harsh industrial environments. Ethernet connectivity enables centralized data access and rapid diagnostics. At 0.4 kg, it balances durability with installation flexibility.
$200.00 $100.00
You have seen 96 out of 209 products