نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
The Bently Nevada 3500/70M 176449-09 is a 4-channel Recip Impulse Velocity Monitor designed for the 3500 series rack-based monitoring system. It is specifically engineered to provide critical protection for reciprocating compressors by monitoring crankcase and crosshead vibration. The module processes inputs from seismic transducers, conditions the signals to derive precise vibration measurements, and evaluates them against user-programmable alarm setpoints.Features
Four-channel monitoring capability for high-density rack configurations.
Supports multiple measurement modes including Impulse Acceleration, Acceleration 2, Recip Velocity, and Low Frequency Recip Velocity.
Programmable Alert and Danger setpoints for active static values.
Fast update rate of less than 100 milliseconds for real-time protection.
Compatible with 3500 series rack infrastructure and configuration software.
Applications
Reciprocating Compressors: Essential for detecting mechanical faults in crankcases and crossheads.
Pipeline Compression: Maintains the operational reliability of large-scale compressor stations.
Oil and Gas Production: Supports monitoring requirements for upstream and downstream gas compression assets.
Chemical and Petrochemical Processing: Provides vibration monitoring for critical rotating and reciprocating equipment.
Technical Specifications
Model
3500/70M 176449-09
Power Consumption
7.7 W (nominal)
Voltage Input
-22 Vdc (minimum)
Output Impedance
550 Ohm (typical)
Load Resistance
600 Ohm (maximum)
Resolution
0.3662 uA (maximum)
Accuracy
+/- 0.05 mA; +/- 0.14 mA over temperature range
Storage Temperature
-40 degC to +85 degC
Humidity
95% non-condensing
Installation Guidelines
Ensure the 3500 rack power is disconnected before installing or removing the module.
The module should be seated firmly into the designated rack slot to ensure proper backplane connection.
Use shielded cabling for all transducer inputs to minimize electromagnetic interference (EMI).
Ensure proper grounding of the 3500 rack chassis to a common instrument ground to maintain signal integrity.
Verify that the module configuration matches the installed transducer type and required alarm setpoints via the 3500 configuration software.
FAQWhat is the primary function of the 3500/70M module?The 3500/70M is a 4-channel monitor designed to process seismic transducer inputs for reciprocating compressor vibration analysis, specifically for crankcase and crosshead monitoring.How does the 3500/70M differ from the 3500/72M?While both are 4-channel rack-based monitors for reciprocating compressors, the 3500/70M is designed for seismic vibration inputs, whereas the 3500/72M is intended for piston rod position and drop monitoring using proximity probes.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
The Bently Nevada 330881-28-06-155-03-02 is a high-performance ProxPac XL Proximity Transducer Assembly designed for industrial vibration and position monitoring. This self-contained system integrates a 3300 XL 8 mm proximity probe and a 3300 XL Proximitor sensor into a single, robust housing, eliminating the need for external extension cables and separate sensor enclosures.Features
Integrated 3300 XL 8 mm proximity probe and Proximitor sensor system.
Self-contained design simplifies installation and reduces field wiring complexity.
Constructed with AISI 304 stainless steel and durable PPS housing for harsh environments.
Threaded sleeve design allows for precise probe gap adjustment of +/- 12.7 mm.
Compatible with standard 3/4-14 NPT machine case mounting.
Includes M20 fitting and two plugs for versatile connectivity.
Applications
Radial vibration and axial position monitoring for steam and gas turbines.
Predictive maintenance for centrifugal compressors in space-constrained installations.
General machinery protection for pumps, large motors, and fans.
Monitoring in high-heat or harsh industrial environments such as steel and metal mills.
Technical Specifications
Model Number
330881-28-06-155-03-02
Probe Type
3300 XL 8 mm
Standoff Adapter
60 mm
Probe Penetration
155 mm
Mounting Thread
3/4-14 NPT
Housing Material
AISI 304 Stainless Steel / PPS
Weight
1.55 kg
Installation Guidelines
Ensure the assembly is mounted through the machine case using the 3/4-14 NPT thread.
For assemblies where the combined B and C dimensions exceed 305 mm (12.0 in), additional sleeve support is required to prevent resonance.
Maintain a nominal probe tip gap of 1.27 mm (0.050 in) from the target surface during initial setup.
The installation must maintain at least an IP54 protection rating to ensure sensor integrity.
Always power down the monitoring system before performing any wiring changes or maintenance on the transducer assembly.
Handle with care to avoid damage to the probe tip; ensure the assembly is properly grounded according to site safety standards.
FAQWhat is the primary function of the 330881-28-06-155-03-02?This unit is a fully integrated proximity transducer assembly used to measure shaft vibration and position on rotating machinery, combining the probe and sensor into one unit to streamline installation.What is the typical operating gap voltage?For 3300 XL series probes, the normal operating gap voltage is generally maintained between -9 V and -11 V DC.Does this assembly require an external extension cable?No, the ProxPac XL design integrates the Proximitor sensor directly into the housing, removing the need for an extension cable between the probe and the sensor.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
The Bently Nevada 330881-16-04-138-03-02 is a PROXPAC XL Proximity Transducer system. Unlike traditional proximity systems that utilize separate components, the PROXPAC XL integrates the probe, extension cable, and Proximitor sensor into a single, self-contained unit. This design simplifies installation and reduces the number of connection points in vibration monitoring applications.Features
Integrated system design combining probe, extension cable, and Proximitor sensor
Housing constructed from Polyphenylene Sulfide (PPS), a molded thermoplastic reinforced with glass and conductive fibers for electrostatic dissipation
Rated for Type 4X and IP66 environments, providing protection in severe industrial conditions
8 mm 3300 XL probe technology
Configured with 40 mm standoff adapter and 138 mm probe penetration
Includes one M20 fitting and two plugs
Mounting thread: 3/4-14 NPT
ApplicationsThis transducer is designed for continuous monitoring and protection of critical rotating machinery, including:
Steam and gas turbines in power generation
Large centrifugal, axial, and process gas compressors
Critical boiler feed pumps and high-pressure process pumps
Large electric motors and industrial generators
Heavy-duty industrial gearboxes requiring precise shaft alignment monitoring
Technical Specifications
Model Number
330881-16-04-138-03-02
Probe Type
3300 XL 8 mm
Standoff Adapter
40 mm
Probe Penetration
138 mm
Fittings
One M20 fitting, two plugs
Mounting Thread
3/4-14 NPT
Housing Material
Polyphenylene Sulfide (PPS)
Environmental Rating
Type 4X / IP66
Installation Guidelines
Gapping: For optimal performance, gap the probe at the center of its linear range. For this 8 mm system, the target gap is typically 1.27 mm (50 mils), corresponding to an output of approximately -10 VDC.
Cross-Talk Prevention: Maintain a minimum separation between transducer tips of at least 40 mm (1.6 in) for axial measurements or 38 mm (1.5 in) for radial vibration to prevent signal interference.
Handling: Ensure the system is powered down before performing any wiring or maintenance. Handle with care to avoid damage to the probe tip or cable insulation.
Environment: Ensure the mounting location is free from excessive mechanical shock and that the housing is properly sealed using the provided fittings to maintain the IP66 rating.
FAQWhat is the primary function of the PROXPAC XL?It is designed for real-time, high-precision monitoring of vibration and position in rotating machinery, ensuring safe operation through continuous condition monitoring.What is the working principle of this transducer?The transducer operates on the principle of electromagnetic induction to measure shaft displacement and vibration without physical contact.Is this part still available?The 330881-16-04-138-03-02 may be available for purchase and support even if it has reached End-Of-Life (EOL) status from the original manufacturer.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
DescriptionThe Bently Nevada 3300/48 Case Expansion Monitor is a rack-mounted module designed to measure the thermal expansion of turbine casings relative to their foundation. This measurement is critical for steam turbines and other large rotating machinery where casing growth can lead to mechanical interference. The monitor continuously compares expansion values against configured alarm setpoints, providing early warning of abnormal conditions to facilitate predictive maintenance.Features
Measures casing expansion relative to the foundation.
Continuous parameter comparison against Alert and Danger alarm setpoints.
Relay actuation for alarm conditions.
LED indicators for OK, Bypass, Alert, and Danger status.
Compatible with proximity probes or LVDT signals.
ApplicationsThis module is primarily utilized in power generation and industrial facilities for monitoring steam turbine thermal growth, ensuring mechanical alignment and preventing casing damage during thermal cycling.Technical Specifications
Model
3300/48-03-02-02-00
Brand
Bently Nevada
Series
3300
Operating Temperature
0 to 60 degC
Power Consumption
~1.5 W
Sensitivity
200 mV/mil or 100 mV/mil
Signal Accuracy
+/- 0.33% typical
Outputs
4-20 mA, 1-5 VDC, 0 to -10 VDC
Installation Guidelines
Ensure the 3300 rack is powered down before inserting or removing the module.
Handle the module using standard ESD precautions to prevent damage to internal circuitry.
Ensure the module is fully seated in the rack slot to maintain proper backplane connection.
Use shielded cabling for transducer inputs to minimize EMI interference.
Verify that the transducer signal type matches the module configuration settings.
FAQWhat is the primary function of the 3300/48 monitor?The module monitors the thermal expansion of turbine casings relative to the foundation, which is essential for preventing mechanical interference in large rotating machinery.Can this module be used with different types of sensors?Yes, the 3300/48-03-02-02-00 is configured to accept inputs from proximity probes or LVDTs, depending on the specific application requirements.What do the alarm setpoints control?The module provides relay outputs for Alert and Danger conditions, which can be integrated into the plant's safety or control systems to trigger alarms or automated shutdowns.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
The Bently Nevada TK-3E 177313-02-02-00 is a motorized, portable proximity system test kit designed to simulate shaft vibration and position for the calibration and verification of Bently Nevada eddy current proximity transducer systems. This kit ensures that transducer inputs and monitor readouts remain accurate, supporting critical machinery condition monitoring.Features
Electric-driven calibration system for proximity transducers
Simulates shaft vibration and axial/radial displacement
Precision spindle micrometer assembly for controlled probe positioning
Universal probe mount accommodating diameters from 5 mm to 19 mm
Integrated target wheel assembly with AISI 4140 alloy steel target
Rugged, foam-lined carrying case for field and laboratory use
Applications
Power Generation: Calibration of vibration monitoring loops in thermal, hydroelectric, and nuclear plants
Oil, Gas, & Petrochemicals: Verification of proximity sensors in refineries and offshore processing facilities
Rotating Equipment: Routine maintenance and commissioning for centrifugal compressors, steam turbines, and large industrial fans
Machinery Protection: Checking thrust position drift and radial vibration linearity to prevent rotor-to-stator contact
Technical Specifications
Model
TK-3E 177313-02-02-00
Vibration Amplitude Range
50 um to 254 um (2 to 10 mils) peak-to-peak
Spindle Micrometer Range
0 to 25.4 mm (0 to 1000 mils)
Operating Temperature
0 degC to 50 degC (32 degF to 122 degF)
Storage Temperature
-18 degC to 65 degC (0 degF to 150 degF)
Humidity
95% Non-Condensing
Power Supply
115/230 VAC, 50/60 Hz
Target Material
AISI 4140 Alloy Steel
Installation Guidelines
Ensure the test kit is placed on a stable, level surface. The base includes vibration isolation feet to minimize external interference.
Verify the power supply voltage setting (115V or 230V) matches the local power source before connecting.
When mounting the proximity probe, ensure it is securely held in the universal mount without over-tightening the clamp.
Connect the Proximitor sensor to the probe using the appropriate extension cable and provide the required -24 VDC power to the sensor.
Use a digital multimeter to monitor the gap voltage while adjusting the micrometer in calibrated increments to verify the Incremental Scale Factor (ISF).
Always power down the test kit and disconnect from the power source before performing maintenance or cleaning.
FAQWhat is the TK-3E 177313-02-02-00?The Bently Nevada TK-3E 177313-02-02-00 is an electrically driven proximity system test kit used to calibrate vibration monitors and verify the operational condition of proximity transducer systems.Do I need an oscilloscope to use the TK-3E?No, an oscilloscope is not required. You can use a standard digital multimeter to read the gap voltage and evaluate the vibration signal.What is the power requirement for this kit?The unit operates on 95–125 Vac or 190–250 Vac, 50/60 Hz.What are the environmental limits?It is rated for indoor use up to an altitude of 2000 meters. The operational temperature range is 0 degC to 50 degC in up to 95% non-condensing humidity.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
DescriptionThe Bently Nevada 330180-X1-00 (MOD: 145004-81) is a Proximitor sensor designed for use within the 3300 XL proximity transducer system. This sensor is engineered to provide precise, non-contact measurement of shaft position and vibration in rotating machinery. It serves as a critical component in condition monitoring, converting the gap between the probe tip and the observed surface into a proportional voltage signal for analysis by monitoring systems.Features
Compatible with 3300 XL series proximity transducer systems.
Designed for DIN-rail mounting configurations.
Provides high-accuracy signal conditioning for vibration and position monitoring.
Robust construction suitable for industrial environments.
Technical Specifications
Product Model
330180-X1-00 MOD:145004-81
Device Type
Proximitor Sensor
Manufacturer
Bently Nevada
Weight
0.22 kg
Tariff Code
8537101190
Installation Guidelines
Ensure the Proximitor sensor is installed in a protected, dry environment, typically within an instrumentation cabinet.
Use appropriate DIN-rail mounting hardware to secure the module.
Maintain proper shielding for all signal cables to minimize EMI/RFI interference.
Verify that the system length (probe, extension cable, and sensor) matches the calibrated configuration (e.g., 5.0m or 9.0m) to ensure measurement accuracy.
Always power down the monitoring system before connecting or disconnecting the sensor to prevent electrical damage.
FAQWhat is the primary function of the 330180 Proximitor sensor?The Proximitor sensor is the signal conditioning unit of the proximity transducer system. It receives an RF signal from the probe, processes it, and outputs a voltage signal proportional to the distance between the probe tip and the target surface.Is this sensor compatible with all Bently Nevada systems?This model is specifically part of the 3300 XL series. It is recommended to verify compatibility with your existing probe and extension cable lengths before installation.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
DescriptionThe Bently Nevada 3500/91-01-02-02 EGD Communication Gateway Module is a critical component of the 3500 Series Machinery Protection System. It is engineered to facilitate high-speed, real-time data exchange between the 3500 rack and external plant control systems, such as GE Mark VIe controllers, using the Ethernet Global Data (EGD) protocol. This module ensures robust connectivity for machinery diagnostics, protection data, and integration with System 1 software.Features
Provides Ethernet Global Data (EGD) protocol integration for real-time communication.
Equipped with an Ethernet 100BASE-FX fiber optic interface for superior noise immunity and long-distance data transmission.
Supports seamless data exchange for predictive maintenance and transient data analysis.
Front panel LED indicators for quick status monitoring: OK, TX/RX, and Bypass.
Designed for integration into the standard 3500 rack communication slot.
ApplicationsThis communication gateway is primarily used in critical turbomachinery protection applications, including steam and gas turbines, centrifugal compressors, and large pumps, where high-speed data integration with plant-wide control systems is required.Technical Specifications
Manufacturer
Bently Nevada
Product Number
3500/91-01-02-02
Module Type
EGD Communication Gateway
I/O Module Type
Ethernet 100BASE-FX Fiber Optic
Agency Approval
CE/PCCC
Operating Temperature
-30 degC to +65 degC
Storage Temperature
-40 degC to +85 degC
Humidity
95% non-condensing
Installation Guidelines
Ensure the 3500 rack is powered down before inserting or removing the module to prevent electrical damage.
The module must be installed in the designated communication slot of the 3500 rack, paired with the corresponding rear I/O module.
Handle with care using ESD-safe procedures to protect sensitive internal components.
Ensure fiber optic cables are routed away from high-EMI sources and are not subjected to excessive bending radii.
Verify that the module is fully seated and the front panel screws are tightened to ensure proper grounding and mechanical stability.
FAQWhat is the primary function of the 3500/91 module?The module serves as a gateway to allow the 3500 Machinery Protection System to communicate with external control systems using the EGD protocol over a fiber optic network.Does this module support standard copper Ethernet?No, this specific order code (3500/91-01-02-02) is configured for 100BASE-FX fiber optic connectivity.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
DescriptionThe Bently Nevada 3300/16 XY/Gap Dual Vibration Monitor is a specialized rack-mounted module designed for the 3300 Monitoring System. It provides simultaneous measurement of radial shaft vibration and probe gap voltage. By continuously monitoring these parameters against user-defined alarm setpoints, the module provides critical protection for rotating machinery, including industrial turbines, centrifugal compressors, and large pumps. This unit supports predictive maintenance strategies by delivering reliable, high-resolution displacement and vibration data to the control system.Features
Dual-channel monitoring capability for XY vibration and gap voltage.
Continuous signal processing with integrated Alert and Danger alarm logic.
Compatible with standard Bently Nevada proximity probe and Proximitor sensor systems.
Front-panel LED status indicators for OK, Bypass, Alert, and Danger conditions.
Configurable output options including 4-20 mA, 1-5 VDC, and 0 to -10 VDC signals.
Designed for seamless integration into existing 3300 series rack environments.
Applications
Radial shaft vibration monitoring for fluid-film bearing machines.
Proximity probe gap voltage monitoring for machine health diagnostics.
Critical asset protection in petrochemical, power generation, and oil and gas facilities.
Integration with DCS or PLC systems for automated machinery shutdown and data logging.
Technical Specifications
Model
3300/16-13-01-01-00-00-00
Brand
Bently Nevada
Series
3300
Operating Temperature
0 to 60 deg C
Power Consumption
~1.5 W
Input Compatibility
Proximity probes with Proximitor sensors
Sensitivity
200 mV/mil (8 V/mm) or 100 mV/mil (4 V/mm)
Signal Accuracy
±0.33% typical, ±1% max at 25 deg C
Output Signals
4-20 mA, 1-5 VDC, 0 to -10 VDC
Installation Guidelines
Ensure the 3300 rack is powered down before inserting or removing the monitor module to prevent electrical damage.
The module must be installed in a clean, dry environment within the specified temperature range.
Use shielded twisted-pair cabling for all transducer inputs to minimize EMI/RFI interference.
Ensure proper grounding of the 3300 rack system per Bently Nevada installation manuals to maintain signal integrity.
Verify that all field wiring is correctly terminated at the rack backplane before applying power.
Confirm that the configuration switches/jumpers match the specific transducer and range requirements for the application.
FAQWhat is the primary function of the 3300/16 monitor?The 3300/16 is designed to monitor radial shaft vibration and probe gap voltage simultaneously, providing essential data for machinery protection and condition monitoring.Is this module compatible with existing 3300 series racks?Yes, this module is specifically engineered for the 3300 rack system and is fully compatible with standard 3300 backplanes.What do the status LEDs on the front panel indicate?The LEDs provide visual confirmation of the module's operational status, including OK (system health), Bypass (maintenance mode), and Alert/Danger (alarm thresholds exceeded).
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
DescriptionThe Bently Nevada 21000-00-00-00-000-00-02 is an aluminum proximity probe housing assembly designed for the external mounting of proximity probes on industrial rotating machinery. This unit provides a robust, environmentally sealed enclosure that protects the proximity probe and its electrical connections, while enabling precise positioning of the probe tip relative to the target surface for accurate vibration and position monitoring.This specific model is a base housing unit configured without an integrated probe, sleeve, or conduit fittings. It serves as a mechanical foundation for 3300 XL 8 mm proximity probes, allowing for field-customized installations. The assembly includes the aluminum housing body, a dome cover, O-rings, and a thread seal, with a 3/4-14 NPT mounting thread.Features
Aluminum construction for durability in industrial environments.
Provides environmental protection for proximity probes and cable connections.
Allows for external probe adjustment and maintenance without machine disassembly.
Includes a dome cover for secure, sealed access to internal components.
Compatible with standard 3/4-14 NPT conduit connections.
Supports precise probe penetration adjustment within a 13 mm range.
Applications
Oil and Gas Refineries: Protecting vibration monitoring sensors on compressors, pumps, and turbines.
Power Generation: Safeguarding turbine-generator shaft sensors in hydro, fossil, and nuclear plants.
Petrochemical Facilities: Shielding probes from volatile or corrosive atmospheres.
Heavy Manufacturing: Supporting fluid-film bearing machine monitoring in continuous-operation environments.
Technical Specifications
Model
21000-00-00-00-000-00-02
Material
Aluminum
Mounting Thread
3/4-14 NPT
Adjustment Range
13 mm (±0.5 in)
Weight
0.8 kg
Included Components
Housing body, dome cover, O-rings, thread seal
Installation Guidelines
Ensure the mounting surface is clean and flat to maintain the integrity of the housing seal.
Route field wiring through the designated 3/4-14 NPT threaded ports.
Use appropriate cable seal grips or conduit fittings to maintain the weatherproof and explosion-proof rating of the assembly.
Tighten the dome cover securely using the captive screws to ensure the internal environment remains sealed.
For probe penetration lengths exceeding 300 mm (12 inches), install additional sleeve support to prevent resonance.
Always verify the probe-to-target gap during commissioning using the 13 mm adjustment range.
FAQWhat is the primary function of the 21000-00-00-00-000-00-02?This assembly acts as a protective, adjustable housing for proximity probes, allowing for the monitoring of machine vibration and position while protecting the transducer system from environmental hazards.Is this housing compatible with all Bently Nevada probes?It is designed primarily for use with Bently Nevada 3300, 3300 XL, and 7200 series proximity transducer systems. Please consult your specific probe datasheet to ensure mechanical compatibility.Does this unit include conduit fittings?No, this specific model (-00 in the fitting position) is supplied as a base housing without pre-installed conduit fittings or probes.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
DescriptionThe Bently Nevada 3300/55 Dual Velocity Monitor is a rack-mounted module within the 3300 Series monitoring system. It is specifically engineered to measure casing vibration velocity by interfacing with Velomitor piezo-velocity sensors. The 3300/55-01-05-12-12-00-00-05-00 configuration provides two independent channels of vibration monitoring, featuring enhanced input scaling and relay logic designed for the protection of critical turbomachinery.Features
Dual-channel independent velocity measurement.
Compatible with standard Velomitor piezo-velocity sensors.
Proportional 4-20 mA outputs for integration with external control systems (DCS/PLC).
Configurable relay outputs for Alert and Danger alarm conditions.
Front-panel LED status indicators for OK, Bypass, Alert, and Danger states.
Enhanced input scaling and alarm logic for precise machinery protection.
ApplicationsThis module is widely used in industrial environments for continuous monitoring of critical rotating equipment, including steam turbines, gas turbines, centrifugal compressors, and large pumps. It provides the necessary signal processing to detect casing vibration anomalies and trigger protective shutdowns or operator alerts.Technical Specifications
Model
3300/55-01-05-12-12-00-00-05-00
Brand
Bently Nevada
Series
3300
Inputs
2 x Velomitor piezo-velocity sensors
Outputs
4-20 mA proportional, Relay (Alert/Danger)
Operating Temperature
0 degC to +60 degC
Power Consumption
~1.5 W typical
Installation Guidelines
Ensure the 3300 rack is powered down before inserting or removing the module to prevent electrical damage.
Verify that the module is properly seated in the rack slot and that the front-panel screws are tightened to ensure a secure ground connection.
Use shielded twisted-pair cabling for sensor inputs to minimize EMI/RFI interference.
Maintain proper ventilation within the cabinet to ensure the ambient temperature remains within the 0 degC to +60 degC range.
Follow standard ESD (Electrostatic Discharge) handling procedures when touching internal components or connectors.
FAQWhat is the primary function of the 3300/55 module?The 3300/55 is designed to monitor casing vibration velocity. It processes signals from two Velomitor sensors and compares them against user-defined Alert and Danger setpoints to protect rotating machinery.Can this module be used in hazardous areas?This specific order code (3300/55-01-05-12-12-00-00-05-00) includes standard input barrier configuration (no intrinsic safety). Please verify your site's hazardous area requirements before installation.What do the LED indicators on the front panel represent?The LEDs provide immediate visual feedback for the module's health and the status of the monitored machinery, specifically indicating OK (sensor/module health), Bypass (maintenance mode), Alert, and Danger alarm conditions.
DescriptionThe Bently Nevada 3300/55 Dual Velocity Monitor is a key component of the 3300 Monitoring System, designed to provide continuous, reliable vibration monitoring for industrial rotating machinery. This module accepts input from velocity seismoprobes to monitor casing vibration, ensuring equipment health and protection through precise signal processing and alarm capabilities.Features
Dual-channel monitoring for independent or redundant vibration measurement.
Configurable scale factors including 500 mV/in/s, 145 mV/in/s, and 100 mV/in/s.
Integrated 4-20 mA recorder outputs for external data logging and trend analysis.
Wide frequency response range from 3 Hz to 10,000 Hz.
Robust design for harsh industrial environments with high humidity tolerance.
ApplicationsThis monitor is widely used in power generation, oil and gas, and petrochemical facilities to protect critical assets such as turbines, compressors, pumps, and fans. It is specifically engineered for casing vibration monitoring where velocity-based measurements are required to detect mechanical faults.Technical Specifications
Product Model
3300/55
Sensitivity
500 mV/in/s, 145 mV/in/s, or 100 mV/in/s
Frequency Range
3 Hz to 10,000 Hz (180-600,000 cpm)
Accuracy
Within +/- 0.33% of full-scale typical
Resolution
Within +/- 1.6% of monitor full-scale
Output Impedance
100 Ohm
Operating Temperature
0 degC to +65 degC (+32 degF to +150 degF)
Storage Temperature
-40 degC to +85 degC (-40 degF to +185 degF)
Relative Humidity
Up to 95%, non-condensing
Installation Guidelines
Ensure the 3300 rack is properly grounded to a clean earth point to minimize electrical noise.
Always power down the rack before inserting or removing the 3300/55 module to prevent damage to the backplane connectors.
Use shielded twisted-pair cabling for all signal inputs to maintain signal integrity and reduce EMI/RFI interference.
Verify that the probe sensitivity settings on the module match the installed seismoprobe specifications.
Maintain adequate airflow around the 3300 rack to ensure the module operates within the specified temperature range.
FAQWhat is the primary function of the 3300/55?The 3300/55 is a dual-channel velocity monitor used to measure and track casing vibration on rotating machinery, providing necessary alarm outputs for machinery protection.Can this module be used with different seismoprobes?Yes, the module supports multiple sensitivity settings (500, 145, and 100 mV/in/s), allowing it to be configured for various compatible velocity sensors.
DescriptionThe Bently Nevada 3300/35 Temperature Monitor is a rack-mounted module designed to measure multiple temperature points in turbines, compressors, and other critical rotating machinery. The 05 suffix option specifies a 6-channel configuration, supporting both RTD and thermocouple inputs. It continuously compares temperature readings against alarm setpoints, providing early warning of abnormal thermal conditions and enabling predictive maintenance.Features
Six independent input channels for comprehensive thermal monitoring.
Supports a wide range of sensor types including RTDs (Pt100, Pt1000) and thermocouples (J, K, T types).
Integrated alarm logic with Alert and Danger setpoints.
Front-panel LED indicators for system status: OK, Bypass, Alert, and Danger.
Standard relay outputs for direct integration with plant safety and control systems.
ApplicationsThis module is primarily used in industrial environments for monitoring bearing temperatures, stator windings, and equipment casings in large rotating machinery such as gas and steam turbines, centrifugal compressors, and large electric motors.Technical Specifications
Model
3300/35-05-02-01-00-00
Brand
Bently Nevada
Series
3300
Channels
6
Input Types
RTD (Pt100, Pt1000), Thermocouple (J, K, T)
Operating Temperature
-35 degC to +65 degC
Power Consumption
~2 W
Accuracy
+/- 0.5% typical
Outputs
4-20 mA, 1-5 VDC, Relay (Alert/Danger)
Installation Guidelines
Ensure the 3300 rack is powered down before inserting or removing the module to prevent electrical damage.
Ensure proper grounding of the rack system to mitigate EMI/RFI interference.
Use shielded twisted-pair cabling for all sensor inputs to maintain signal integrity.
Verify that sensor wiring matches the configured input type (RTD vs. Thermocouple) before applying power.
Maintain adequate ventilation around the rack to ensure operating temperatures remain within the specified -35 degC to +65 degC range.
FAQWhat sensor types are compatible with this module?This specific model supports RTDs (Pt100 and Pt1000) and standard J, K, and T type thermocouples.Does this module require external barriers?The 00 suffix in the barrier option position indicates that this unit is configured with standard input barriers; ensure your installation environment complies with hazardous area requirements if applicable.How are the alarm setpoints configured?Alarm setpoints for Alert and Danger conditions are configured through the Bently Nevada 3300 system interface, allowing for independent thresholds per channel.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
DescriptionThe Bently Nevada 3500/77M 140734-07 is a high-performance four-channel monitor module engineered for the 3500 Machinery Protection System. This module is specifically designed to measure and analyze dynamic cylinder pressure in reciprocating machinery, such as compressors and reciprocating engines. By processing signals from dynamic pressure transducers, the 3500/77M provides continuous monitoring of pressure profiles, peak values, and critical diagnostic parameters to ensure machinery integrity and prevent catastrophic failure.Features
Four independent monitoring channels for high-density data acquisition.
Compatible with dynamic cylinder pressure transducers.
Provides real-time cylinder pressure waveform analysis, peak pressure tracking, and diagnostic parameter calculation.
Programmable alert and danger thresholds with configurable voting logic for alarm and trip functions.
Seamless integration into the 3500 rack system, fully configurable via Bently Nevada 3500 Rack Configuration Software.
Applications
Reciprocating compressors.
Large-scale reciprocating engines.
Machinery protection systems requiring cylinder pressure monitoring and diagnostic waveform capture.
Technical Specifications
Product Model
3500/77M
Order Code
140734-07
Channels
4
Operating Temperature
-30 degC to +65 degC
Storage Temperature
-40 degC to +85 degC
Humidity
95% non-condensing
Power Consumption
Supplied via 3500 rack backplane
Installation Guidelines
Ensure the 3500 rack is powered down before inserting or removing the module to prevent electrical damage.
Use appropriate ESD protection when handling the module to avoid damage to sensitive electronic components.
Ensure the module is fully seated in the rack slot and the front panel screws are tightened to maintain proper grounding and EMI shielding.
Route signal cables away from high-voltage lines or sources of electromagnetic interference to maintain signal integrity.
Verify that the I/O module and the monitor module match the configuration defined in the 3500 software.
Compliance and Certifications
Safety Standards: EN 61010-1, LV Directive 2014/35/EU
EMC Compliance: EN 61000-6-2 (Immunity), EN 61000-6-4 (Emissions)
Hazardous Area: CSA/NRTL/C Class I, Zone 2
RoHS: Directive 2011/65/EU compliant
FAQDoes this module include the I/O card?The 3500/77M module typically requires a corresponding I/O module for field wiring termination. Please verify if your specific order includes the required I/O module or if it is being purchased separately.Is this module compatible with all 3500 racks?The 3500/77M is designed for standard 3500 rack systems. Ensure your rack firmware and configuration software versions are compatible with this module revision.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
DescriptionThe Bently Nevada 172103-01 is a 16-channel RTD and isolated tip thermocouple I/O module designed for use with the 3500/65 Temperature Monitor within the 3500 Series Machinery Protection System. This module serves as the physical interface between field temperature sensors and the monitor, providing signal conditioning and internal terminations for up to 16 channels. It is engineered to support critical machinery protection by monitoring bearings, windings, lubrication systems, and turbine components.Features
16-channel capacity for comprehensive temperature monitoring.
Supports 3-wire RTD, 4-wire RTD, and isolated tip thermocouple inputs.
Internal termination design eliminates the need for external termination blocks.
Automatic internal cold junction compensation for thermocouple inputs.
16-bit ADC conversion with high measurement accuracy (±0.1% of reading or ±0.5 degC).
Compatible with 3500 Rack Configuration Software for alarm setpoint programming.
Applications
Steam, gas, and hydroelectric turbines.
Centrifugal, axial, and reciprocating process gas compressors.
Large industrial motors and power generation units.
Critical high-pressure or high-flow pumps in refineries and water treatment facilities.
Power recovery expanders and specialized turbo-machinery.
Technical Specifications
Model
172103-01
Channels
16
Sensor Types
3-wire RTD, 4-wire RTD, Isolated Tip Thermocouple
Thermocouple Types
J, K, T, E, R, S, B, N
Temperature Range
-200 degC to +850 degC (RTD)
Operating Temperature
-30 degC to +65 degC
Storage Temperature
-40 degC to +85 degC
Weight
0.45 kg
Rack Space
1 full-height rear slot
Installation Guidelines
Ensure the 3500 rack is powered down before inserting or removing the I/O module.
The module requires one full-height rear slot in the 3500 series rack.
Use 16 to 22 AWG twisted shielded pair or triad cabling for field wiring.
Shields must be connected to the instrument earth at the barrier ground.
Internal termination modules cannot be used in conjunction with external termination blocks or cables.
Follow standard ESD (Electrostatic Discharge) precautions when handling the module to prevent damage to internal circuitry.
Compliance and CertificationsThe 172103-01 complies with FCC Part 15, EMC Directive 2014/30/EU, LV Directive 2014/35/EU, and RoHS Directive 2011/65/EU. It holds hazardous area certifications including CSA/NRTL/C Class I, Zone 2, and ATEX/IECEx II 3G Ex nA nC ic IIC T4 Gc, as well as marine certifications from ABS and DNV GL.FAQWhat is the 172103-01?The Bently Nevada 172103-01 is an RTD/Isolated Tip Thermocouple I/O module with internal terminations, used specifically for the 3500/65 Temperature Monitoring system.Does this module require an external termination block?No, this model features internal terminations. If your application requires an external termination block, the alternative model 172109-01 should be used.How are the sensors configured?The module is configured via the 3500 Rack Configuration Software, allowing for a mix of supported RTD and thermocouple inputs across the 16 available channels.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
DescriptionThe Bently Nevada 125672-02 is a 4-channel Proximitor/Seismic Monitor Module designed for the 3500 Machinery Protection System. This module is engineered to continuously compare monitored parameters against configured alarm setpoints to drive alarms and relay modules, ensuring critical machinery protection in industrial environments. It accepts input signals from proximity or seismic transducers, processes the data, and provides proportional outputs for integration into control and monitoring systems.Features
4-channel monitoring capability for proximity or seismic sensors.
Configurable alarm setpoints for machinery protection.
Integrated signal processing for 1X and 2X vector filtering.
Designed for rack-mount installation within the 3500 series chassis.
Typical power consumption of 7.7 watts.
Technical Specifications
Model
125672-02
Series
3500/42
Channels
4
Power Consumption
7.7 W (typical)
Gap Filter
-3 dB at 0.09 Hz
Smax Range
0.125 to 15.8 times running speed
1X and 2X Vector Filter
Constant Q Filter, -57.7 dB rejection in stopband
Output Impedance
550 Ohm
Voltage Compliance
0 to +12 Vdc range across load
Installation Guidelines
Ensure the 3500 rack is powered down before inserting or removing the module to prevent electrical damage.
Verify that the module is fully seated in the rack slot and that the front panel screws are tightened to ensure proper grounding and mechanical stability.
Use shielded cables for all transducer inputs to minimize EMI/RFI interference.
Maintain proper ventilation within the cabinet to ensure the module operates within its specified temperature range.
Handle with care using ESD-safe practices to prevent damage to sensitive internal circuitry.
FAQWhat is the primary function of the 125672-02 module?The 125672-02 is a Proximitor/Seismic Monitor Module used to process vibration and position signals from transducers, providing monitoring and alarm functions for rotating machinery within a Bently Nevada 3500 system.Is this module compatible with all 3500 series racks?The 125672-02 is designed for the 3500 series rack environment. Ensure your rack configuration and firmware support this specific monitor module before installation.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
DescriptionThe Bently Nevada 161216-02 Ethernet 100BASE-FX I/O Module is a specialized communication interface designed for the 3500 Machinery Protection System. This module facilitates high-speed, fiber-optic Ethernet connectivity, allowing the 3500 rack to communicate reliably with external control systems, including DCS, PLC, and SCADA platforms. By utilizing the 100BASE-FX protocol, the module provides robust, noise-immune data transmission, which is essential for maintaining system integrity in electrically noisy industrial environments such as refineries and power generation facilities.Features
Provides fiber-optic 100BASE-FX Ethernet connectivity for the 3500 series rack.
Ensures high immunity to electromagnetic interference (EMI) due to fiber-optic transmission.
Supports real-time data exchange for vibration, alarm, and system health monitoring.
Designed for integration into standard 3500 series rack backplanes.
Supports redundant communication paths for increased system availability.
ApplicationsThis module is intended for use in critical machinery protection and condition monitoring applications where long-distance or noise-resistant communication is required. It is commonly deployed in oil and gas, petrochemical, and power generation plants to bridge the gap between Bently Nevada monitoring racks and plant-wide control networks.Technical Specifications
Model
161216-02
Brand
Bently Nevada
Series
3500
Communication Protocol
Ethernet 100BASE-FX
Operating Temperature
-40 to +85 deg C
Power Consumption
24 VDC nominal
Mounting
3500 Rack-mounted
Installation Guidelines
Ensure the 3500 rack power is disconnected before inserting or removing the module.
Handle the module using standard ESD (Electrostatic Discharge) protection practices to prevent damage to internal circuitry.
Slide the module into the designated rack slot, ensuring the backplane connector is properly aligned and fully seated.
Secure the module using the integrated front-panel fasteners to ensure proper grounding and mechanical stability.
Use appropriate fiber-optic cabling and ensure connectors are clean and free of debris before installation.
Route fiber-optic cables away from high-heat sources and avoid sharp bends that could compromise signal integrity.
FAQIs this module compatible with all 3500 series racks?The 161216-02 is designed for the 3500 series architecture. Please verify your specific rack configuration and firmware requirements to ensure compatibility with your existing system setup.Does this module require external power?No, the module receives its nominal 24 VDC power directly from the 3500 rack backplane supply.Can this module be used in redundant configurations?Yes, the 161216-02 supports redundant communication paths, allowing for high-availability setups in critical monitoring applications.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
The Bently Nevada 129957-085-310-05 is a high-performance 8.5-meter extension cable designed for the 3300 XL 8mm Proximity Transducer System. This cable provides a reliable link between the proximity probe and the Proximitor sensor, ensuring accurate transmission of vibration and displacement signals in critical industrial monitoring applications.Features
Designed for 3300 XL 8mm proximity transducer systems
8.5-meter cable length for flexible installation
Gold-plated ClickLoc connectors for secure, reliable signal transmission
Patented CableLoc design providing 330 N (75 lbf) pull strength
Electrically and physically interchangeable with non-XL 3300 5mm and 8mm components
Applications
Steam, gas, and hydroelectric turbines
Centrifugal air, process gas, and refrigeration compressors
Large-scale industrial electric motors
Power generation equipment
Critical process pumps in chemical and petrochemical plants
Technical Specifications
Product Model
129957-085-310-05
Cable Length
8.5 meters
Characteristic Impedance
50 Ohm +/- 2 Ohm
Capacitance
98 pF/m (30 pF/ft)
Attenuation
< 0.28 dB/m @ 10 MHz
Withstand Voltage
2 kV AC (shield-to-conductor)
Connector Type
Gold-plated ClickLoc
Installation Guidelines
Finger-Tight Only: Connect the cable to the probe and Proximitor sensor by hand until a click is felt or heard. Do not use pliers or wrenches; maximum torque is 0.565 N-m (5 in-lb).
Bend Radius: Maintain a minimum bend radius of 25.4 mm (1.0 inch) to prevent damage to the internal coaxial structure.
Connector Protection: Use connector protectors for all connections to prevent moisture or oil ingress. Silicone tape may be used in non-oil environments, but is not recommended for applications exposed to turbine oil.
Handling: Ensure the system is powered down before disconnecting or connecting components to prevent signal noise or potential damage.
FAQWhat is the primary function of the 129957-085-310-05?This cable serves as an extension for the 3300 XL 8mm proximity probe, facilitating the transmission of eddy current signals used to monitor vibration and displacement in rotating machinery.Is this cable compatible with older Bently Nevada systems?Yes, the 3300 XL series is designed to be both electrically and physically interchangeable with legacy non-XL 3300 5mm and 8mm transducer components.Can I use this cable in high-vibration environments?Yes, the 3300 XL series is specifically engineered for industrial environments, featuring robust CableLoc designs to ensure connection integrity under mechanical stress.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
DescriptionThe Bently Nevada 3300/25 Dual Accelerometer Monitor is a high-reliability, rack-mounted module designed for the 3300 Series monitoring system. This unit provides continuous, dual-channel monitoring of casing vibration, utilizing accelerometer inputs to protect critical rotating machinery such as turbines, compressors, and pumps. By comparing real-time vibration data against pre-configured alarm setpoints, the module ensures timely detection of mechanical faults.Features
Dual independent channels for simultaneous monitoring of two vibration points.
Continuous signal processing with dedicated Alert and Danger alarm setpoints.
Integrated relay outputs for automated machine protection and shutdown sequences.
Proportional 4–20 mA outputs for integration with external control systems or data recorders.
Front-panel LED indicators providing immediate status updates for OK, Bypass, Alert, and Danger conditions.
Designed for integration into standard 3300 Series rack environments.
ApplicationsThis monitor is specifically engineered for industrial environments requiring precise casing vibration analysis. It is commonly deployed in power generation, petrochemical processing, and oil and gas facilities to monitor the structural health of centrifugal pumps, gas turbines, and large-scale compressors.Technical Specifications
Model
3300/25-01-03-03-00-00-01-00
Series
3300
Inputs
2 x Accelerometer channels
Outputs
Dynamic signals, 4-20 mA, Relay (Alert/Danger)
Operating Temperature
-30 degC to +65 degC
Power Consumption
~6 W
Installation Guidelines
Ensure the 3300 Series rack is properly grounded to a common plant ground to minimize EMI/RFI interference.
Handle the module using standard ESD-safe practices to prevent damage to internal circuitry.
Verify that the slot in the 3300 rack is configured correctly for the 3300/25 module before insertion.
Always power down the rack before inserting or removing the monitor module to prevent electrical arcing or configuration errors.
Use shielded cables for all transducer inputs to maintain signal integrity in high-noise industrial environments.
Ensure adequate airflow within the cabinet to maintain operating temperatures within the specified -30 degC to +65 degC range.
FAQWhat is the primary function of the 3300/25 monitor?The 3300/25 is designed to measure casing vibration using accelerometer inputs, providing continuous monitoring and alarm functionality to protect rotating machinery.Does this module support intrinsic safety?The specific model 3300/25-01-03-03-00-00-01-00 is configured with standard input barriers (no intrinsic safety barriers). Please verify your site requirements for hazardous area classification.How are the alarm setpoints configured?Alarm setpoints for Alert and Danger conditions are configured within the 3300 series system architecture, allowing for precise threshold management based on the specific vibration characteristics of the monitored equipment.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
The Bently Nevada 3300/40-13-01-01-00-01 is a specialized rack-mounted Eccentricity Monitor module designed for the 3300 monitoring system. It is engineered to track shaft eccentricity and rotor bow in large rotating machinery, such as steam turbines and compressors, particularly during slow-roll startup and shutdown sequences. By processing inputs from proximity probe systems, this module provides continuous monitoring and alarm logic to support predictive maintenance and asset protection.Features
Dedicated eccentricity measurement for shaft bow and slow-roll displacement analysis.
Continuous signal processing with real-time comparison against user-defined Alert and Danger setpoints.
Integrated LED status indicators for OK, Bypass, Alert, and Danger conditions.
Compatible with standard Bently Nevada proximity probe and Proximitor sensor configurations.
Provides proportional output signals for external data logging and control systems.
ApplicationsThis module is primarily utilized in critical industrial environments for the continuous monitoring of large rotating equipment. It is essential for detecting rotor misalignment or thermal bowing during machine transients, helping to prevent catastrophic failure by triggering alarms before operational limits are exceeded.Technical Specifications
Model
3300/40-13-01-01-00-01
Brand
Bently Nevada
Series
3300
Operating Temperature
0 to 60 degC
Power Consumption
Approx. 1.5 W
Sensitivity
200 mV/mil or 100 mV/mil (programmable)
Signal Accuracy
+/- 0.33% typical
Current Output
+4 to +20 mA
Voltage Output
+1 to +5 VDC / 0 to -10 VDC
Installation Guidelines
Ensure the 3300 rack is powered down before inserting or removing the module to prevent electrical damage.
Verify that the module is fully seated in the rack slot and that the front panel screws are tightened to ensure proper grounding.
Use shielded cabling for all transducer inputs to minimize electromagnetic interference (EMI) in high-noise industrial environments.
Maintain adequate airflow around the 3300 rack to ensure the module operates within its specified temperature range.
Confirm that all jumper settings and configuration switches match the specific requirements of the machine train before commissioning.
FAQWhat is the primary function of the 3300/40 module?The 3300/40 is designed to measure peak-to-peak eccentricity, which is the amount of shaft bow, primarily during slow-roll conditions when the machine is rotating at low speeds.Does this module require external power?The module receives power directly from the 3300 rack backplane once installed.What do the LED indicators on the front panel represent?The LEDs provide visual status for the OK (transducer health), Bypass (maintenance mode), Alert, and Danger alarm states.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
The Bently Nevada 330103-00-04-05-02-05 is a high-performance 3300 XL 8 mm proximity probe designed for non-contact vibration and position measurement. This probe is a critical component of the 3300 XL transducer system, providing reliable data for monitoring shaft displacement, vibration, and speed in industrial rotating machinery.Features
Compliant with API 670 standards for mechanical configuration, linear range, and accuracy.
Patented TipLoc and CableLoc designs ensure a robust bond and high pull strength (330 N / 75 lbf).
Miniature coaxial ClickLoc connector with gold-plated, corrosion-resistant contacts.
Improved RFI/EMI immunity for reliable operation in harsh electromagnetic environments.
Fully interchangeable and backward compatible with 3300 series 5 mm and 8 mm system components.
Applications
Power Generation: Monitoring steam and gas turbine shafts and large generator sets.
Oil & Gas: Tracking high-load centrifugal compressors, multi-stage pumps, and expanders.
Hydroelectric: Monitoring turbine setups with wide clearance requirements.
Heavy Manufacturing: Asset protection for steel rolling mills, paper mill rollers, and mining machinery.
Technical Specifications
Model
330103-00-04-05-02-05
Probe Diameter
8 mm
Thread Size
M10 x 1
Unthreaded Length
0 mm
Case Length
40 mm
Total Length
0.5 meter
Connector Type
Miniature coaxial ClickLoc
Approvals
CSA, ATEX, IECEx
Installation Guidelines
Ensure the M10 x 1 threaded body is screwed cleanly into the mounting bracket or housing.
Maintain a minimum clear radius of 30 mm (1.2 in) around the probe tip to prevent interference.
Observe the metal-free zone requirements to avoid distortion of the eddy-current RF field.
Space adjacent probe tips at least 40 mm (1.6 in) apart to prevent signal crosstalk.
Handle with care to avoid damage to the probe tip; ensure the system is powered down before connecting or disconnecting cables.
FAQWhat is the primary function of this probe?It provides continuous, non-contact measurement of static parameters like shaft position and dynamic parameters like shaft vibration using the eddy current principle.Does this probe require an extension cable?Yes, because the probe cable length is 0.5 meters, it must be used with a compatible 3300 XL extension cable to reach the Proximitor sensor.What is the sensitivity of the 3300 XL 8 mm system?The system provides a standard scale factor sensitivity of 200 mV/mil (7.87 V/mm).
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
DescriptionThe Bently Nevada 3300/52-01-00-00 is a dedicated Rotation Reverse Monitor Module within the 3300 Series machinery protection system. This module is engineered to provide continuous, reliable monitoring of shaft rotation direction in critical rotating equipment, such as turbines and compressors. By detecting reverse rotation conditions, the module enables timely alarm and trip actions to prevent catastrophic mechanical failure.Features
Continuous monitoring of shaft rotation direction to ensure operational integrity.
Integrated Alert and Danger relay outputs for automated machinery protection.
Front-panel LED status indicators for OK, Bypass, Alert, and Danger conditions.
Designed for seamless integration into the standard Bently Nevada 3300 rack architecture.
Configured for compatibility with proximity probe or tachometer input signals.
ApplicationsThis monitor is primarily utilized in industrial environments requiring protection for rotating machinery where reverse rotation poses a significant risk to equipment health. Typical applications include steam and gas turbines, centrifugal compressors, and large-scale pumps.Technical Specifications
Model
3300/52-01-00-00
Series
3300
Input Type
Proximity probe or tachometer
Relay Outputs
Standard Alert and Danger
Operating Temperature
-30 degC to +65 degC
Power Consumption
1.5 W (typical)
Installation Guidelines
Ensure the 3300 rack is powered down before inserting or removing the module to prevent electrical damage.
Verify that the module is fully seated in the rack slot to ensure proper backplane connection.
Use shielded cabling for all transducer inputs to minimize electromagnetic interference (EMI).
Maintain adequate ventilation around the rack system to ensure operating temperatures remain within the specified -30 degC to +65 degC range.
Follow standard ESD (Electrostatic Discharge) precautions when handling the module to protect internal circuitry.
FAQWhat is the primary function of the 3300/52 module?The module is designed to detect reverse rotation in critical rotating machinery and trigger alarm or trip relays to prevent mechanical damage.Is this module compatible with existing 3300 series racks?Yes, the 3300/52 is a standard component of the 3300 series machinery protection system and is designed for full rack integration.What type of sensors does this module accept?This specific configuration (01-00-00) is designed to accept inputs from proximity probes or tachometers to determine shaft direction.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
DescriptionThe Bently Nevada 3500/15E is a high-performance power supply module designed specifically for the 3500 Machinery Protection System. This module provides reliable power distribution to the rack, supporting the critical monitoring functions required for industrial rotating machinery. The 3500/15E configuration features universal AC input capabilities, ensuring compatibility with a wide range of global power standards in industrial environments.Features
Designed for integration with the Bently Nevada 3500 Series rack system.
Supports universal AC input voltage (85 to 264 Vac rms).
Robust design suitable for demanding industrial temperature ranges.
High-reliability power conversion for continuous monitoring applications.
Redundant power supply support when used in pairs within the 3500 rack.
Technical Specifications
Product Model
3500/15E
Input Voltage Range
85 to 264 Vac rms
Operating Temperature
-30 degC to +65 degC (-22 degF to +150 degF)
Storage Temperature
-40 degC to +85 degC (-40 degF to +185 degF)
Humidity
95%, non-condensing
Manufacturer
Bently Nevada
Installation Guidelines
Ensure the rack power is disconnected before installing or removing the 3500/15E module.
The module should be seated firmly into the designated power supply slot of the 3500 rack chassis.
Verify that the input voltage matches the module specifications before applying power.
Maintain adequate airflow around the 3500 rack to ensure the module operates within its specified temperature range.
Use proper ESD precautions when handling the module to prevent damage to internal electronic components.
FAQCan this module be used for redundant power configurations?Yes, the 3500/15E is designed to support redundant power configurations when two modules are installed in the same 3500 rack.What is the input voltage range for this specific unit?This unit is configured for universal AC input, supporting a range of 85 to 264 Vac rms.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
The Bently Nevada 330901-00-08-10-02-CN is a high-performance 3300 NSv (Near-Switch) proximity probe designed for precision vibration and position monitoring in constrained environments. This transducer system is engineered specifically for applications where standard 5 mm or 8 mm probes cannot be utilized due to side-view, rearview, or counter-bore restrictions.Features
Optimized for tight installation requirements and small target applications.
Standard scale factor of 7.87 V/mm (200 mV/mil).
Equipped with a miniature coaxial ClickLoc connector for secure, reliable signal transmission.
Designed for compatibility with fluid-filmed bearing machinery.
Supports integration with Bently Nevada condition monitoring platforms.
ApplicationsThis probe is ideal for small-diameter shafts (less than 51 mm / 2 in) and small flat targets (less than 15 mm / 0.6 in). Common industrial applications include:
Radial vibration and position measurements.
Axial (thrust) position monitoring.
Tachometer and zero-speed sensing.
Phase reference (Keyphasor) signal acquisition.
Health monitoring for centrifugal compressors, steam/gas turbines, pumps, and gearboxes.
Technical Specifications
Model Number
330901-00-08-10-02-CN
Thread Size
1/4-28 UNF
Case Length
0.8 in (20.3 mm)
Unthreaded Length
0.0 in
Cable Length
1.0 meter (39 in)
Connector Type
Miniature coaxial ClickLoc
Linear Range
1.5 mm (60 mils)
Operating Temperature
-52 degC to +177 degC
Agency Approvals
Multiple Approvals
Installation Guidelines
Ensure the probe is mounted in a secure, vibration-free bracket to prevent false signal noise.
Use caution when tightening the 1/4-28 UNF thread; do not exceed torque specifications to avoid damaging the probe casing.
Maintain proper clearance from the target to ensure the probe operates within its linear range (typically starting 0.25 mm from the target).
Route coaxial cables away from high-voltage power lines and sources of electromagnetic interference (EMI).
Verify that the Proximitor sensor impedance matches the NSv probe requirements before system power-up.
FAQWhat is the primary purpose of the 330901 NSv probe?It is designed for machinery where conventional probes are too large, specifically for small-diameter shafts or constrained spaces where side-view clearance is limited.Is this probe interchangeable with standard 3300 XL 8mm probes?No. The NSv system requires a dedicated NSv Proximitor sensor due to different impedance characteristics and is not directly interchangeable with standard 3300 XL 8mm components.Does this probe require special handling?Yes, as a precision measurement device, the probe tip must be kept clean and free of debris. Ensure the ClickLoc connector is fully seated to maintain signal integrity.
نحن نقدم خدمة التوصيل في اليوم التالي من الاثنين إلى الجمعة إذا كان المنتج موجودًا في المخزون والاستثناءات في أيام العطلات.
عطلات نهاية الأسبوع
نحن لا نقدم أي تسليمات في عطلة نهاية الأسبوع.
دولي
نوفر خدمة التوصيل في اليوم التالي، حسب موقعك. تحقق من حالة طلبك عبر هذا الرابط.
The Bently Nevada 990-10-XX-01-00 (MOD 163930-01) is a two-wire, loop-powered vibration transmitter designed to provide a 4-20 mA proportional signal for machinery control systems. This device integrates the Proximitor sensor directly into the transmitter housing, eliminating the need for external signal conditioning units. It is specifically engineered for OEM applications involving small pumps, motors, fans, and centrifugal air compressors.Features
Integrated Proximitor sensor functionality for reduced installation complexity.
Non-isolated PROX OUT and COM terminals, supplemented by a coaxial connector.
Non-interacting zero and span potentiometers for precise calibration.
Dedicated test input pin for rapid verification of loop signal output.
Not OK/Signal Defeat circuit to prevent false alarms or erroneous high outputs.
Potted construction suitable for high-humidity environments, including up to 100% condensing conditions.
Applications
Centrifugal air compressor monitoring.
Vibration trending for small pumps and motors.
Integration into PLC-based machinery protection systems.
General-purpose vibration monitoring in industrial environments.
Technical Specifications
Model
990-10-XX-01-00 MOD 163930-01
Full-scale Range
0-10 mils pp (0-250 um pp)
System Length
5.0 meters or 7.0 meters
Mounting
35 mm DIN rail clips
Device Type
2-wire, loop-powered transmitter
Compatible Probes
3300 NSv proximity probes
Output Signal
4-20 mA
Installation Guidelines
Ensure the system is powered down before performing any wiring, installation, or removal of the module.
Mount the transmitter on a 35 mm DIN rail in a location protected from excessive heat and direct moisture.
Use shielded cabling for the 4-20 mA loop to minimize electromagnetic interference (EMI).
Verify that the proximity probe and extension cable match the system length requirements (5m or 7m) specified for the transmitter.
Ensure proper grounding of the signal shield at the control system end to maintain signal integrity.
Handle the device with standard ESD precautions to prevent damage to internal circuitry.
FAQWhat is the primary function of the 990-10-XX-01-00?This transmitter is designed to convert vibration data from a 3300 NSv proximity probe into a 4-20 mA signal, allowing standard PLCs to monitor vibration levels on rotating machinery.Is this unit compatible with System 1 software?No, the 4-20 mA output provides peak-to-peak trending data only and does not support the advanced diagnostic capabilities required for systems like Bently Nevada System 1 or Rule Paks.What system lengths are supported?The 990-10-XX-01-00 is compatible with 5.0-meter and 7.0-meter system length configurations.
