General Electric (GE) menawarkan rangkaian lengkap produk otomasi industri. Portofolionya meliputi PACSystems RX3i/RX7i, modul Genius I/O, pengontrol Mark VIe, dan sistem PLC. Produk-produk GE menjamin keandalan operasional, otomatisasi yang terukur, dan dukungan jangka panjang untuk aplikasi industri di seluruh dunia.
General Electric
-
General Electric IS200VVIBH1C GE Vibration Input Module
GE IS200VVIBH1C Vibration Input Module Configured for vibration signal acquisition in GE Mark VI / Mark VIe Speedtronic control systems, the GE IS200VVIBH1C (IS200VVIB Vibration Input Module) provides direct physical/electrical execution for multi-channel sensor conditioning, digitization, and machinery monitoring signal processing. Hardware Specifications Parameter Specification Model IS200VVIBH1C Brand GE (General Electric) Origin United States Weight 0.5 kg Dimensions 6U VME single-slot card form factor Operating Temp -20 to +70 deg C Power Consumption 2.8 A @ 5 VDC Input Channels Up to 8 ICP/IEPE vibration inputs or up to 14 proximity, velocity, accelerometer, and LVDT inputs Sensor Excitation 4 mA constant current for ICP sensors; -28 VDC nominal for proximity probes Input Voltage Range +/-10 V for ICP sensors; +/-20 VDC for proximity probe signals Frequency Range 0.5 Hz to 20 kHz programmable filtering range Sampling Rate Up to 100 kHz per channel on Mark VIe; 4,600 SPS per channel on Mark VI Resolution 16-bit ADC Dynamic Range Approx. 80 dB Isolation 1500 V RMS field-to-logic; 500 V channel-to-channel Redundancy Support Compatible with simplex, dual, and TMR Mark VI configurations Profinet / EtherNet Deterministic Signal Processing Characteristics The IS200VVIBH1C operates as a vibration acquisition interface within GE Speedtronic Mark VI and Mark VIe architectures. The module receives analog vibration and position signals from field sensors, performs signal conditioning, and converts input data through a 16-bit ADC for controller-level processing. The module supports industrial control I/O density scaling through multiple sensor input configurations, including proximity probes, accelerometers, velocity transducers, and LVDTs. Its compatibility with simplex, dual, and triple modular redundancy configurations enables integration into different Mark VI control architectures. Signal processing functions include configurable band-pass, low-pass, and high-pass filtering. The module architecture supports firmware flash compatibility within the supported GE control platform for configuration and application management. Frequently Asked Questions Q: What sensor types can be connected to the IS200VVIBH1C?A: The module accepts vibration and position signals from ICP/IEPE accelerometers, proximity probes, velocity transducers, and LVDTs according to the configured input mode. Q: What type of signal conversion is used in the vibration input module?A: The module uses a 16-bit ADC for analog signal digitization with programmable sampling performance depending on Mark VI or Mark VIe system configuration. Q: Can the IS200VVIBH1C operate in redundant control architectures?A: The module supports integration with simplex, dual, and TMR (Triple Modular Redundancy) Mark VI system configurations. Field Installation Guidelines Install the IS200VVIBH1C in the designated 6U VME rack slot of the GE Mark VI or Mark VIe control system. Verify card seating, connector engagement, and rack power isolation before insertion or removal. Route vibration sensor wiring separately from high-voltage power conductors and high-current switching circuits. Use shielded sensor cables where required, and terminate cable shields according to the turbine control system grounding design. Confirm sensor type configuration, excitation settings, input channel assignment, and filtering parameters before commissioning. Verify proximity probe polarity, signal reference connections, and field-to-logic isolation requirements during installation.
$200.00 $100.00
-
General Electric IS400UCLIH1A GE Industrial Controller Module
GE IS400UCLIH1A Industrial Controller Module The GE IS400UCLIH1A, also cataloged as the IS400UCLI Industrial Controller Module, operates as a dedicated hardware component for real-time control execution and data communication within GE Speedtronic Mark V / Mark VIe control platforms. Hardware Specifications Parameter Specification Model IS400UCLIH1A Brand GE (General Electric) Origin United States Weight 0.95 kg Dimensions 72 x 36 x 85 mm Operating Temp -40 to +70 deg C Power Consumption 24 VDC supply, 5 A current input Processor High-speed industrial CPU for real-time control processing Memory Volatile and non-volatile memory with Flash and RAM support Communication Ethernet, serial, fieldbus, and GE proprietary protocols I/O Support Modular I/O expansion interface for control system integration Mounting Rack installation, DIN rail, or panel mounting EtherNet/IP and Control Bus Execution Characteristics The IS400UCLIH1A is configured as a control processor module within GE Speedtronic Mark V / Mark VIe architectures. The module executes application logic, manages real-time I/O data exchange, and communicates with distributed control components through supported Ethernet, serial, fieldbus, and proprietary communication channels. The controller architecture supports modular I/O density scaling through connected input and output assemblies. Firmware flash compatibility allows application software updates and controller configuration management within the supported GE control environment. Frequently Asked Questions Q: What power input is required for the IS400UCLIH1A controller module?A: The module operates from a 24 VDC power source with a specified current requirement of 5 A. Q: Does the IS400UCLIH1A support replacement without system shutdown?A: The module design supports hot-swappable replacement procedures when applied within a compatible GE rack configuration and according to system installation requirements. Q: Which communication interfaces are available on this controller module?A: The module supports Ethernet, serial communication, fieldbus interfaces, and GE proprietary communication protocols. Field Installation Guidelines Install the IS400UCLIH1A in the designated GE Speedtronic Mark V / Mark VIe rack or approved mounting assembly. Verify mechanical seating, connector alignment, and power isolation before module insertion or removal. Use shielded communication cables where required by the control system design. Connect cable shields according to site grounding practices to reduce electromagnetic interference. Separate communication wiring from high-voltage power conductors and maintain appropriate cable routing practices. Confirm firmware compatibility, controller configuration parameters, and I/O addressing before commissioning. Ensure ventilation paths remain unobstructed and that environmental conditions remain within the specified operating range.
$200.00 $100.00
-
General Electric GE IS200STAIH2A Simplex Analog Input Terminal Board
GE IS200STAIH2A Simplex Analog Input Terminal Board The GE IS200STAIH2A, also cataloged as the IS200STAIH2A Simplex Analog Input Terminal Board, operates as a dedicated hardware component for analog signal termination and conditioning within GE Mark VIe Speedtronic turbine control platforms. It provides field sensor signal routing, filtering, and interface functions between analog devices and controller input processing modules. Hardware Specifications Parameter Specification Model IS200STAIH2A Brand GE (General Electric) Origin USA Product Type Simplex Analog Input Terminal Board System Compatibility Mark VI / Mark VIe Speedtronic Signal Channels 12 analog input channels Signal Interface Analog field signal termination Supported Signals Analog voltage/current inputs via terminal interface Maximum Lead Resistance 15 ohm Output Supply 24 VDC Technology Surface mount technology Mounting DIN rail or panel mounting Weight 0.5 kg Operating Temp -30 to +65 deg C Power Consumption Supplied through associated control system interface GE Mark VIe Analog Signal Interface Characteristics The IS200STAIH2A provides analog input field termination for GE turbine control architectures. The board supports I/O density scaling through multiple analog input channels and transfers conditioned field signals to compatible analog processing modules. The terminal board design incorporates filtering components and signal separation methods to reduce field noise coupling. Surface mount construction supports compact installation within Mark VIe control cabinets. The board operates as a physical signal interface and does not perform standalone signal computation. Frequently Asked Questions Q: What is the primary function of the IS200STAIH2A?A: The IS200STAIH2A terminates and conditions analog field signals before transmission to the turbine controller input processing hardware. Q: Does the IS200STAIH2A contain an independent processor?A: No. The board functions as a terminal interface component. Analog conversion and processing are performed by the associated controller input modules. Q: What installation method is supported for this terminal board?A: The board supports cabinet installation using DIN rail or panel mounting arrangements according to the Mark VIe system configuration. Field Installation Guidelines Install the IS200STAIH2A on a properly secured control cabinet mounting surface. Verify terminal assignments before connecting field wiring. Use shielded cables for low-level analog signal wiring where required. Connect cable shields according to the cabinet grounding design to reduce EMI/RFI coupling. Separate analog signal wiring from high-current power conductors and relay switching circuits. Inspect terminal connections for proper mechanical tightening and confirm that field device polarity matches the controller wiring documentation before system energization.
$200.00 $100.00
-
General Electric GE IS200TBCIH1C Contact Input Terminal Board
GE IS200TBCIH1C Contact Input Terminal Board The GE IS200TBCIH1C, also cataloged as the IS200TBCI Contact Input Terminal Board, operates as a dedicated hardware component for discrete contact signal termination and field input conditioning within the GE Mark VI Speedtronic turbine control system. The board interfaces external switches and relay contacts with controller input circuits. Hardware Specifications Parameter Specification Model IS200TBCIH1C Brand GE Origin United States Series Mark VI Speedtronic Product Type Terminal Board Board Type Contact Input Terminal Board Input Channels 24 contact inputs Input Voltage Range 24 VDC / 125 VDC Signal Type Discrete contact input signals Isolation Optical isolation per channel Filtering RC network noise suppression Controller Interface 37-pin D-sub connector Field Interface Screw terminals Jumper Pins 2 metal pins Mounting Typical DIN rail mounting Weight 0.5 kg Dimensions 200 mm x 150 mm x 35 mm Operating Temp -30 to +65 deg C I/O Density Scaling and Mark VI Discrete Signal Interface The IS200TBCIH1C provides contact input termination functions within the GE Mark VI Speedtronic control architecture. The board receives discrete signals from field devices including limit switches, pressure switches, and protective relay contacts, then transfers conditioned input states to the turbine controller. The terminal board supports GE industrial control platform integration through dedicated controller connections and contributes to I/O density scaling by providing multiple contact input channels in a compact terminal assembly. Optical isolation separates field circuits from controller electronics, while RC filtering reduces interference from external switching environments. The module supports GE Mark VI system configurations with firmware flash compatibility across associated control hardware assemblies. The terminal interface design provides direct signal routing for turbine protection logic, permissive monitoring, and interlock functions. Frequently Asked Questions Q: How many contact input channels are available on the IS200TBCIH1C?A: The board provides 24 discrete contact input channels for field device monitoring. Q: What type of field devices can connect to the IS200TBCIH1C?A: The board interfaces with discrete devices such as switches, relay contacts, and protective input circuits. Q: What mounting method is specified for the IS200TBCIH1C?A: The board is designed for typical DIN rail mounting within the Mark VI control cabinet. Field Installation Guidelines Install the IS200TBCIH1C on the designated DIN rail location and verify terminal identification before connecting field contact wiring. Confirm input voltage compatibility and jumper configuration before system energization. Route contact input cables separately from high-current switching conductors to reduce EMI/RFI coupling. Apply cabinet grounding practices for shielded cables where applicable. Verify controller connector seating, field terminal connections, and input channel assignments during commissioning.
$200.00 $100.00
-
General Electric GE IS200SRLYH2A Relay Output Terminal Board
GE IS200SRLYH2A Relay Output Terminal Board The GE IS200SRLYH2A, also cataloged as the IS200SRLY Relay Output Terminal Board, operates as a dedicated hardware component for relay signal switching and field device control within the GE Mark VIe and EX2100 turbine control systems. The board converts controller output commands into relay contact actions for external circuits. Hardware Specifications Parameter Specification Model IS200SRLYH2A Brand GE Origin United States Series Mark VIe / EX2100 Product Type Simplex Relay Output Terminal Board Board Type Relay Output Terminal Board Relay Channels 12 relay channels Relay Contact Type Relay output interface Maximum Load Current 125 VDC Coil Voltage 24 VDC nominal Isolation Electrical isolation between relay circuits and control logic Mounting DIN rail / EX2100 chassis slot Technology Surface Mount Weight 480 g Operating Temp -30 to +65 deg C Firmware Flash Compatibility and Industrial Relay Control Interface The IS200SRLYH2A provides relay output termination functions within the GE Mark VIe industrial control architecture. The board receives low-level controller commands and transfers them through relay contacts to external field devices such as solenoids, alarms, and turbine auxiliary circuits. The module supports industrial control platform integration through GE I/O architectures and maintains firmware flash compatibility within the Mark VIe system environment. Relay output density scaling allows multiple discrete control circuits to be managed through a single terminal board assembly. The surface mount design provides compact relay signal routing and supports electrical separation between controller logic and field switching circuits. The relay interface is used for discrete command execution in turbine protection, excitation control, and interlock applications. Frequently Asked Questions Q: How many relay output channels are available on the IS200SRLYH2A?A: The board provides 12 relay output channels according to the specified Mark VIe configuration. Q: What type of field devices can be controlled by the IS200SRLYH2A?A: The relay outputs can interface with discrete field devices including solenoids, alarms, and auxiliary switching circuits. Q: What mounting options are supported by the IS200SRLYH2A?A: The board supports installation in the EX2100 chassis configuration or designated DIN rail mounting arrangements. Field Installation Guidelines Install the IS200SRLYH2A in the assigned Mark VIe or EX2100 control cabinet position and verify relay terminal identification before connecting field wiring. Confirm contact ratings and load requirements before energizing connected circuits. Use separated routing for relay output wiring and low-level signal cables to reduce electrical interference. Connect protective grounding according to cabinet design requirements and verify relay contact status during commissioning procedures.
$200.00 $100.00
-
General Electric GE IS200TDBSH6A Turbine I/O Terminal Board
GE IS200TDBSH6A Turbine I/O Terminal Board Configured for digital field signal termination and I/O interface execution in the GE Mark VIe Speedtronic turbine control system, the GE IS200TDBSH6A (IS200TDBS Turbine I/O Terminal Board) provides direct physical/electrical execution between field devices and turbine controller logic circuits. The board handles digital input and relay output connections for turbine control and protection functions. Hardware Specifications Parameter Specification Model IS200TDBSH6A Brand GE Origin United States Series Mark VIe Module Type Turbine I/O Terminal Board Number of Channels 24 Digital Input Channels 24 channels Relay Output Channels 12 channels Input Voltage 24 VDC / 125 VDC Input Current 24 VDC Input Filter Hardware filter AC Voltage Rejection 12 V RMS Output Type Relay channels for field device control Power Requirements +5 VDC Isolation Optical isolation between channels Technology Surface Mount Mounting DIN rail / panel mount Weight 0.7 kg Operating Temp -30 to +65 deg C Profinet / EtherNet/IP Deterministic Networks and Digital I/O Scaling The IS200TDBSH6A provides digital I/O expansion and field termination capability within the GE Mark VIe control architecture. The board supports I/O density scaling through multiple digital channels and interfaces with turbine controller assemblies through dedicated terminal connections. The module uses hardware filtering and optical isolation to condition field signals and reduce electrical interference. Digital input circuits support dry contact and voltage-driven signals, while relay output channels provide switching interfaces for external turbine devices. The terminal board design supports GE industrial control platforms using structured backplane communication and firmware flash compatibility within the Mark VIe product family. Surface mount technology provides compact signal routing for digital control applications. Frequently Asked Questions Q: How many digital channels are available on the IS200TDBSH6A?A: The board provides 24 digital channels, including digital input termination and relay output interface functions. Q: What filtering method is used on the IS200TDBSH6A?A: The board uses hardware input filtering to reduce signal disturbances from field wiring. Q: What type of output channels are provided by the IS200TDBSH6A?A: The board provides 12 relay channels for interfacing with external control devices such as relays and solenoid circuits. Field Installation Guidelines Install the IS200TDBSH6A in the assigned Mark VIe cabinet location using the specified DIN rail or panel mounting arrangement. Verify field terminal assignments before connecting digital input and relay output wiring. Use separated cable routing for low-level digital signals and high-current switching circuits. Ground cable shields according to cabinet grounding practices where shielded wiring is used. Confirm input voltage levels, relay contact wiring, and connector seating before applying system power.
$200.00 $100.00
-
General Electric GE IS200STTCH2A Thermocouple Input Terminal Board
GE IS200STTCH2A Thermocouple Input Terminal Board The GE IS200STTCH2A, also cataloged as the IS200STTC Thermocouple Input Terminal Board, operates as a dedicated hardware component for thermocouple signal termination and temperature measurement interface within the GE Mark VI/Mark VIe Speedtronic turbine control system. The board receives field thermocouple signals and provides cold junction compensation for temperature data processing. Hardware Specifications Parameter Specification Model IS200STTCH2A Brand GE Origin USA Product Type DIN Rail Thermocouple Board System Compatibility Mark VI / Mark VIe Speedtronic Board Type Simplex Thermocouple Input Terminal Board Input Channels 24 isolated thermocouple inputs Supported Thermocouple Types J, K, T, E, R, S, B Signal Range -8 mV to +45 mV Cold Junction Compensation On-board CJC sensor Field Interface 48 screw terminals Processor Interface 37-pin D-sub connector (JH1) Isolation Channel-to-channel opto-isolation Filtering RC filtering and 50/60 Hz notch filtering Mounting 35 mm DIN rail Weight 0.7 kg Operating Temp -20 to +65 deg C Cold Junction Compensation and Temperature Signal Processing The IS200STTCH2A provides thermocouple signal interface functions for GE Mark VI/Mark VIe turbine control architectures. The board performs field termination, signal conditioning, and cold junction compensation (CJC) before transferring temperature measurement signals to STCC control boards or PAICH1A analog input packs. The module supports channel-to-channel isolation for thermocouple inputs, reducing interference between independent temperature measurement circuits. RC filtering and frequency rejection functions are applied to minimize noise coupling from industrial electrical environments. The simplex STTC architecture provides direct signal routing for temperature monitoring applications. The board integrates with GE industrial control platforms through dedicated terminal connections and supports temperature input density scaling through 24 independent thermocouple channels. Frequently Asked Questions Q: What thermocouple types are supported by the IS200STTCH2A?A: The board supports J, K, T, E, R, S, and B thermocouple input types through software-configured temperature measurement channels. Q: What function does the CJC circuit perform on the IS200STTCH2A?A: The cold junction compensation circuit measures terminal reference conditions and compensates thermocouple voltage readings for ambient temperature effects. Q: What mounting method is used for the IS200STTCH2A?A: The board is designed for 35 mm DIN rail mounting within the Mark VI/Mark VIe control cabinet configuration. Field Installation Guidelines Install the IS200STTCH2A on the designated DIN rail location and verify terminal assignments before connecting thermocouple field wiring. Maintain correct thermocouple polarity and use compatible extension wire materials for each thermocouple type. Route thermocouple cables separately from high-current power wiring and switching circuits. Ground cable shields according to cabinet grounding practices to reduce EMI/RFI interference. Verify connector seating, terminal torque, and channel configuration before system operation.
$200.00 $100.00
-
General Electric GE IS210BAPAH1A Analog Processor Module
GE IS210BAPAH1A Analog Processor Module The GE IS210BAPAH1A, also cataloged as the IS210BAPA Analog Processor Module, operates as a dedicated hardware component for analog signal acquisition, conditioning, and processing within the GE Mark VI/Mark VIe Speedtronic turbine control system. The module receives field sensor inputs including temperature, pressure, vibration, and dynamic pressure signals for real-time control processing. Hardware Specifications Parameter Specification Model IS210BAPAH1A Brand GE Origin United States Functional Acronym BAPA Module Type Analog Processor Module / Safety I/O Pack System Compatibility Mark VI / Mark VIe Speedtronic Processor AMD G-Series dual-core, 1.6 GHz Memory 2 GB DDR3-1066 SDRAM Storage 128 GB Operating System QNX Neutrino RTOS Input Voltage 125 VDC Output Voltage 24 VDC Analog Input Channels 16 differential channels, configurable for 4-20 mA, +/-10 V, TC, RTD Analog Output Channels 8 channels, 0-20 mA A/D Resolution 14-bit Signal Sampling Rate 1 kHz per channel Communication Interfaces 2 x RJ45 Modbus TCP, 1 x RS-485 Mounting DIN-rail PCB Coating Conformal Coating Weight 0.8 kg Operating Temp -30 to +65 deg C Profinet / EtherNet/IP Deterministic Networks and Analog Processing The IS210BAPAH1A integrates analog processing functions within the GE Mark VI/Mark VIe control platform. The module performs signal filtering, scaling, and analog-to-digital conversion before transferring processed values through the controller communication architecture. The module supports firmware flash compatibility within the Mark VIe control environment and provides processor-based execution for real-time analog measurement handling. Its I/O density scaling capability allows multiple sensor input types to be processed through configurable differential channels. For turbine control applications, the BAPA module can process dynamic pressure and acoustic monitoring signals from combustion monitoring sensors. Signal conditioning functions remove unwanted DC components and prepare AC signal content for digital analysis. Frequently Asked Questions Q: What type of field signals can the IS210BAPAH1A process?A: The module supports differential analog inputs including 4-20 mA, +/-10 V, thermocouple, and RTD signal types. Q: What mounting method is specified for the IS210BAPAH1A?A: The module is designed for DIN-rail mounting within the Mark VIe control hardware configuration. Q: What communication interfaces are available on the IS210BAPAH1A?A: The module provides Ethernet communication through 2 x RJ45 interfaces supporting Modbus TCP and an RS-485 interface. Field Installation Guidelines Install the IS210BAPAH1A on the designated DIN-rail mounting location and verify power polarity before applying 125 VDC input power. Connect analog field wiring according to the configured channel assignment and signal type. Use shielded cables for low-level analog sensor connections where required. Ground cable shields according to cabinet grounding practices and route analog signal wiring separately from high-current switching conductors. Verify communication cable termination and network addressing before controller integration.
$200.00 $100.00
-
General Electric GE IS200EPCTG1A Exciter PT/CT Terminal Board
GE IS200EPCTG1A Exciter PT/CT Terminal Board Configured for generator PT/CT signal acquisition and conditioning in the GE EX2100 Excitation Control System, the GE IS200EPCTG1A (IS200EPCT Exciter PT/CT Terminal Board) provides direct physical/electrical execution for voltage and current feedback interface functions. The board receives three-phase PT and CT measurement signals, performs signal conditioning, and transfers isolated measurement outputs to the excitation control rack. Hardware Specifications Parameter Specification Model IS200EPCTG1A Brand GE Origin United States Board Type Exciter PT/CT Terminal Board Series EX2100 Excitation Control System Input Signals 2 x 3-phase PT inputs, 2 x CT inputs PT Input Rating 115 V rms, 50/60 Hz CT Input Rating 1 A / 5 A Analog Output 0-10 V or 4-20 mA Input Burden <= 1 VA Signal Isolation 500 Vrms Power Supply Voltage 28 VDC Weight 0.98 kg Dimensions 33.1 cm x 11.5 cm x 4.5 cm Operating Temp -30 to +65 deg C Power Consumption Not specified Firmware Flash Compatibility and Excitation Control Interface The IS200EPCTG1A operates as an EX2100 excitation system terminal interface board, providing PT/CT measurement routing between generator sensing devices and the excitation controller. The board supports industrial control signal conditioning through dedicated analog input paths and isolated output channels. The module integrates with GE excitation control assemblies using backplane communication structures. Its design supports firmware flash compatibility within the EX2100 control platform and allows I/O density scaling through coordinated terminal board configurations. The PT/CT interface maintains measurement signal integrity by applying input scaling, electrical isolation, and signal filtering. Differential signal handling reduces interference from field wiring environments and supports stable generator voltage and current regulation loops. Frequently Asked Questions Q: What measurement signals are connected to the IS200EPCTG1A?A: The board accepts generator PT voltage feedback signals and CT current feedback signals from excitation system sensing circuits. Q: What isolation function is provided by the IS200EPCTG1A?A: The board provides electrical isolation between PT/CT field measurement circuits and the excitation control electronics to limit fault transfer. Q: What EX2100 system role does this board perform?A: The IS200EPCTG1A functions as a PT/CT terminal interface board for generator voltage and current feedback processing within the EX2100 excitation control system. Field Installation Guidelines Install the IS200EPCTG1A in the designated EX2100 chassis backplane position and verify terminal assignments before connecting PT and CT field wiring. Use properly rated wiring for generator measurement circuits and maintain separation between analog measurement cables and high-current power conductors. Connect cable shields according to the excitation cabinet grounding design to reduce EMI/RFI interference. Confirm CT polarity, PT phase sequence, and signal reference points before system energization. Verify all terminal connections and isolation requirements during commissioning.
$200.00 $100.00
-
General Electric IS200TSVCH2A GE Servo Terminal Board
GE IS200TSVCH2A Servo Terminal Board The GE IS200TSVCH2A, also cataloged as the IS200TSVC Servo Terminal Board, provides physical signal interfacing for electro-hydraulic servo valve control within the GE Mark VI Speedtronic turbine control system. The board processes analog servo command signals and LVDT feedback connections to execute closed-loop actuator positioning through dedicated servo channels. Hardware Specifications Parameter Specification Model IS200TSVCH2A Brand GE Origin United States Board Type Servo Terminal Board System Compatibility Mark VI Speedtronic turbine control system Signal Type Analog servo control signals Servo Channels 4 independent servo channels Operating Voltage 24 VDC / 125 VDC Output Voltage Range -10 V to +10 V Output Current +/-100 mA per channel Communication Interface VMEbus / backplane bus Weight 0.45 kg Dimensions 200 mm x 150 mm x 35 mm Operating Temp -20 to +65 deg C Power Consumption Approx. 15 W Industrial Control Signal Conditioning and Servo Interface The IS200TSVCH2A integrates with the GE Mark VI Speedtronic architecture through backplane communication and dedicated terminal connections. The board supports analog servo command output, LVDT feedback signal processing, and electro-hydraulic actuator loop control. The servo interface uses differential signal paths and signal conditioning circuits to reduce electrical noise influence in actuator feedback loops. The board supports servo valve current regulation through independent channels and provides connection points for turbine fuel valves, inlet guide vane actuators, and steam admission valve systems. The module design supports GE turbine control configurations using redundant control architectures. Firmware flash compatibility and backplane bus communication functions allow integration with Mark VI controller assemblies. Frequently Asked Questions Q: What type of actuator signals does the IS200TSVCH2A process?A: The board processes analog servo control signals for electro-hydraulic servo valves and interfaces with LVDT feedback devices for closed-loop positioning. Q: How many servo control channels are available on the IS200TSVCH2A?A: The module provides 4 independent servo channels for actuator control and feedback signal termination. Q: Can the board be replaced during system operation?A: Hot replacement depends on the Mark VI rack configuration and operating procedure. Servo loops should be placed in an appropriate maintenance state before module replacement. Field Installation Guidelines Install the IS200TSVCH2A in the designated Mark VI control rack location and verify correct terminal assignments before connecting field wiring. Use shielded twisted-pair cables for analog servo and feedback signals where required by the installation design. Terminate cable shields according to the turbine control cabinet grounding practice to reduce EMI/RFI coupling. Separate low-level analog signal wiring from high-current power conductors and switching circuits. Verify actuator loop polarity, feedback direction, and terminal identification before energizing the control system.
$200.00 $100.00
-
General Electric GE IS200SPROH1ADD Backup Protection Terminal Board
GE IS200SPROH1ADD Backup Protection Terminal Board The GE IS200SPROH1ADD, also cataloged as the IS200SPROH1A Backup Protection Terminal Board, operates as a dedicated hardware component for independent voltage sensing and relay interfacing within the GE Mark VI Speedtronic turbine control system. Hardware Specifications Parameter Specification Model IS200SPROH1ADD Brand GE (General Electric) Origin United States Product Type Backup Protection Terminal Board System Compatibility Mark VI Speedtronic Turbine Control System Board Function Backup protection, voltage sensing, relay interfacing Input Voltage 24 VDC power supply Relay Channels 12 Generator and Bus Voltage Sensors 2 Magnetic Speed Pickup Sensitivity 27 mV Magnetic Speed Pickup Pulse Rate Range 2 Hz Protection Rating IP20 Mounting DIN-rail or panel-mounted Weight 0.5 kg Operating Temp -30 to 65 deg C GE Mark VI Speedtronic Protection Interface Characteristics The IS200SPROH1ADD provides backup protection functions through independent signal acquisition and relay interface circuits. The terminal board supports voltage monitoring paths, magnetic speed pickup input processing, and relay channel execution for turbine protection sequences. The board incorporates galvanic relay interfacing to maintain electrical separation between field signals and control circuits. Relay state monitoring and isolated signal paths reduce unwanted switching caused by electrical interference within turbine control environments. The hardware architecture supports fail-safe state execution by maintaining independent protection paths when primary controller communication or processing functions are unavailable. Signal conditioning circuits process magnetic speed pickup inputs with defined sensitivity characteristics for protection logic evaluation. Frequently Asked Questions Q: What type of signals does the IS200SPROH1ADD process?A: The board processes voltage sensing inputs, relay interface signals, and magnetic speed pickup signals for turbine protection functions. Q: How many relay channels are available on this terminal board?A: The IS200SPROH1ADD provides 12 relay channels for protection-related switching and interface functions. Q: What installation methods are supported for this board?A: The board supports DIN-rail or panel-mounted installation depending on system cabinet configuration. Field Installation Guidelines Install the IS200SPROH1ADD in a suitable control cabinet environment with correct mechanical fixation and electrical clearance. Verify terminal assignments before connecting field wiring. Use shielded cables for low-level sensing and speed pickup circuits where electromagnetic interference is present. Connect cable shields according to the grounding practices defined for the Mark VI Speedtronic control cabinet. Separate signal wiring from high-current power conductors and relay switching lines to reduce electrical noise coupling. Confirm power polarity, grounding continuity, and relay interface wiring before energizing the protection circuit.
$200.00 $100.00
-
General Electric GE IS200JPDDG1AAA Mark VI DC Power Distribution Board
GE IS200JPDDG1AAA Mark VI DC Power Distribution Board The GE IS200JPDDG1AAA, also cataloged as the IS200JPDDG1AAA DC Power Distribution Board, operates as a dedicated hardware component for redundant DC power distribution and protection within the GE Mark VI/Mark VIe turbine control platform. It distributes DC supply inputs to controllers, I/O packs, and auxiliary devices through fused output channels. Hardware Specifications Parameter Specification Model IS200JPDDG1AAA Brand GE Product Type DC Power Distribution Boards System Platform Mark VI / Mark VIe Speedtronic Turbine Control System Board Type Jumper Power Distribution Dual (JPDD) Board Input Voltage 24 VDC nominal (20 to 30 VDC); variants support 48 VDC or 125 VDC Redundancy Dual or triple redundant input feeds with automatic failover Outputs 10 to 16 fused output channels Output Current Up to 8 A per channel, 32 A total continuous Fuse Type Replaceable OEM 5 x 20 mm fast-blow fuses Diagnostic Feedback Fault telemetry to IS220PPDA modules Isolation 2500 VAC galvanic separation between power and feedback circuits Mounting DIN rail or rack-mounted Protection Features Conformal coating and surge suppression Microprocessor Intel Celeron 300 MHz Operating System QNX Operating Temp -40 to +70 deg C Storage Temp -40 to +85 deg C Humidity 5% to 95% non-condensing Weight 0.9 kg Industrial Control Power Distribution Characteristics The GE IS200JPDDG1AAA provides DC power distribution functions within the Mark VI/Mark VIe turbine control cabinet architecture. The board accepts redundant DC input sources and distributes protected power through individually fused output branches for controllers, I/O packs, trip solenoids, and auxiliary monitoring devices. The JPDD board supports industrial control power architecture through I/O density scaling and structured DC branch distribution. Diagnostic feedback circuits provide status information including fuse loss, undervoltage conditions, and ground fault monitoring through compatible IS220PPDA interface modules. The AAA suffix configuration includes conformal coating for environmental protection against dust, humidity, and oil mist exposure. Hardware replacement requires verification of controller configuration and firmware flash compatibility within the Mark VI/Mark VIe platform. Frequently Asked Questions Q: What input voltage ranges are supported by the IS200JPDDG1AAA?A: The board supports 24 VDC nominal input operation, with variants available for 48 VDC and 125 VDC supply configurations. Q: How are output faults isolated on this power distribution board?A: Individual fused output channels isolate branch faults to prevent a single output fault from affecting the complete DC distribution bus. Q: What diagnostic information can be transmitted from the board?A: The board provides diagnostic feedback including fuse status, undervoltage conditions, and ground fault indications through compatible PPDA modules. Field Installation Guidelines Install the IS200JPDDG1AAA in the designated Mark VI/Mark VIe turbine control cabinet location using the specified DIN rail or rack mounting hardware. Verify DC input polarity and redundant supply connections before energizing the board. Route DC power wiring separately from low-level signal cables to reduce electromagnetic interference. Use appropriate grounding methods for the cabinet structure and verify protective earth connections. Check all output fuse ratings, field wiring assignments, and connected device power requirements before commissioning. Confirm diagnostic communication with the IS220PPDA interface and verify power distribution status after installation.
$200.00 $100.00
-
General Electric GE IS200EACFG1BAA EX2100 Exciter AC Feedback Board
GE IS200EACFG1BAA EX2100 Exciter AC Feedback Board The GE IS200EACFG1BAA, also cataloged as the IS200EACFG1BAA Exciter AC Feedback Board, operates as a dedicated hardware component for generator AC signal acquisition and feedback conditioning within the GE EX2100 excitation control system. It processes PT and CT inputs and transfers scaled feedback signals to the excitation controller. Hardware Specifications Parameter Specification Model IS200EACFG1BAA Brand GE Product Type Exciter AC Feedback Boards System Platform EX2100 Excitation Control System Board Type Exciter AC Feedback Board Input Signals Generator PT and CT feedback signals Voltage Input 115 V rms nominal Current Input 1 A or 5 A CT input Analog Output Scaled signals to EMIO, 0-10 V or 4-20 mA Isolation 500 Vrms channel-to-earth Mounting Exciter chassis backplane Protection Features Conformal coating and EMI shielding Compliance UL 508, IEC 61010-1, RoHS 3 Operating Temp -30 to +65 deg C Storage Temp -40 to +85 deg C Humidity 5% to 95% non-condensing Origin United States Industrial Control Interface and Firmware Compatibility The GE IS200EACFG1BAA performs AC feedback signal acquisition and conditioning within the EX2100 excitation architecture. The board receives generator voltage and current feedback from PT and CT circuits, converts these signals into scaled analog outputs, and transfers measurement data through the EMIO interface. The module supports deterministic signal exchange within GE excitation control hardware. Its signal conditioning circuitry provides channel isolation and feedback scaling for excitation regulation calculations. The EX2100 platform requires correct hardware identification and firmware flash compatibility when installing replacement boards. I/O configuration parameters must match the installed controller setup before operation. Frequently Asked Questions Q: What type of electrical feedback signals are connected to the IS200EACFG1BAA?A: The board accepts generator PT voltage feedback and CT current feedback signals for excitation regulation processing. Q: What analog outputs are provided by the board?A: The board provides scaled feedback signals to the EMIO interface using 0-10 V or 4-20 mA signal formats. Q: How is the board installed in the EX2100 system?A: The IS200EACFG1BAA is installed in the exciter chassis backplane and interfaces with the EMIO board and exciter controller. Field Installation Guidelines Install the IS200EACFG1BAA in the designated EX2100 exciter chassis backplane position and verify all backplane connections before energizing the system. Connect PT and CT feedback wiring according to the excitation cabinet drawings. Maintain proper separation between low-level analog feedback cables and high-energy excitation conductors to reduce electromagnetic interference. Use shielded signal wiring where required and terminate shields according to the cabinet grounding scheme. Verify CT polarity, PT wiring orientation, and isolation requirements before commissioning. Confirm controller configuration, I/O scaling parameters, and hardware compatibility before placing the excitation system into service.
$200.00 $100.00
-
General Electric GE IS200ERQCH1A EX2100 Exciter Regulator Quick Connect Board
GE IS200ERQCH1A EX2100 Exciter Regulator Quick Connect Board The GE IS200ERQCH1A, also cataloged as the IS200ERQCH1A Exciter Regulator Quick Connect Board, operates as a dedicated hardware component for excitation signal termination and connector interface processing within the GE EX2100 excitation control system. It provides plug-in termination paths for auxiliary contacts, relay outputs, and analog feedback circuits. Hardware Specifications Parameter Specification Model IS200ERQCH1A Brand GE Product Type Exciter Regulator Quick Connect Boards System Platform EX2100 Excitation Control System Board Type Exciter Regulator Quick Connect Board Inputs Auxiliary contact inputs Contact Wetting Voltage 70 VDC (63 to 84 VDC range) Relay Outputs Trip relays and general-purpose Form-C relays Analog Signals PT/CT feedback signals for generator voltage and current Control Voltage 24 VDC Customer Power 125 VDC Isolation 500 VDC channel-to-earth isolation for relay contacts Mounting Quick-connect chassis interface Protection Features Conformal coating and EMI shielding Operating Temp 0 to +60 deg C Storage Temp -40 to +85 deg C Humidity 5% to 95% non-condensing Origin United States Industrial Control Interface and Firmware Compatibility The GE IS200ERQCH1A provides a quick-connect termination interface between EX2100 controller assemblies and external excitation system wiring. The board supports connection of auxiliary contact inputs, relay command circuits, and analog generator feedback signals through dedicated plug-in termination points. Within the EX2100 platform, the board interfaces with ERIO and EMIO assemblies to maintain configured I/O signal paths. The hardware design supports I/O density scaling through structured connector termination and reduces field wiring complexity during cabinet installation. Firmware flash compatibility and hardware revision matching must be verified when integrating the board into an existing EX2100 excitation controller configuration. Frequently Asked Questions Q: What type of signals are terminated through the IS200ERQCH1A?A: The board provides termination interfaces for auxiliary contact inputs, trip relay outputs, general-purpose Form-C relay circuits, and PT/CT analog feedback signals. Q: What is the specified contact wetting voltage for auxiliary inputs?A: Auxiliary contact inputs use 70 VDC wetting voltage with an operating range of 63 to 84 VDC. Q: How is the IS200ERQCH1A connected within the EX2100 system?A: The board uses a quick-connect chassis interface and communicates through connected ERIO/EMIO boards within the excitation control architecture. Field Installation Guidelines Install the IS200ERQCH1A on the designated EX2100 chassis interface location and verify connector engagement before system startup. Confirm all auxiliary input, relay output, and analog feedback wiring assignments according to the cabinet wiring documentation. Maintain separation between analog signal cables and high-current excitation conductors to minimize electromagnetic interference. Apply shield grounding practices according to the control cabinet grounding design. Verify control voltage, customer power connections, and relay contact isolation requirements before energizing the excitation system. Confirm hardware configuration and I/O mapping after installation.
$200.00 $100.00
-
General Electric GE IS200ERIOH1ACB EX2100 Exciter Regulator I/O Board
GE IS200ERIOH1ACB EX2100 Exciter Regulator I/O Board Configured for excitation system signal termination and relay interface execution in the GE EX2100 excitation control platform, the GE IS200ERIOH1ACB (IS200ERIOH1ACB Exciter Regulator I/O Board) provides direct physical/electrical execution between controller hardware and external contact, relay, and analog feedback circuits. Hardware Specifications Parameter Specification Model IS200ERIOH1ACB Brand GE Product Type Exciter Regulator Main I/O Board System Platform EX2100 Excitation Control System Board Type Exciter Regulator I/O Board Inputs Multiple auxiliary contact inputs Contact Wetting Voltage 70 VDC (63 to 84 VDC range) Relay Outputs Trip relays and general-purpose Form-C relays Analog Signals Generator PT/CT voltage and current feedback signals Control Voltage 24 VDC Customer Power 125 VDC Isolation 500 VDC channel-to-earth isolation for relay contacts Mounting Exciter chassis backplane Revision Total 3 revisions Backward Compatibility First two revisions compatible Operating Temp 0 to +60 deg C Storage Temp -40 to +85 deg C Humidity 5% to 95% non-condensing Industrial Control Interface and Firmware Compatibility The GE IS200ERIOH1ACB operates as an I/O expansion and termination interface within the EX2100 excitation control architecture. The board provides electrical connection points for auxiliary contact monitoring, relay command circuits, and generator feedback signals exchanged with the exciter controller. The board interfaces with the EMIO board and supports deterministic signal transfer within the excitation control hardware structure. Revision compatibility must be verified before replacement installation, as only the first two revisions maintain backward compatibility. The EX2100 platform uses configured I/O mapping and firmware-based hardware identification. Proper firmware flash compatibility checking is required when integrating the board into an existing controller assembly. Frequently Asked Questions Q: What field signals can be connected to the IS200ERIOH1ACB?A: The board supports auxiliary contact inputs, trip relay outputs, general-purpose Form-C relay outputs, and analog feedback signals from generator PT/CT circuits. Q: What is the contact wetting voltage specification for this board?A: The auxiliary contact inputs use 70 VDC wetting voltage with an operating range of 63 to 84 VDC. Q: How many revisions exist for the IS200ERIOH1ACB?A: The board has three revisions, with the first two revisions specified as backward-compatible. Field Installation Guidelines Install the IS200ERIOH1ACB in the designated EX2100 exciter chassis backplane position and secure the board using the specified mechanical mounting hardware. Verify all field wiring assignments before connecting contact, relay, and analog signal terminals. Route analog feedback wiring separately from high-current excitation conductors to reduce electromagnetic interference. Use appropriate shield termination practices according to cabinet grounding design requirements. Confirm board revision compatibility, controller configuration parameters, and I/O mapping before system energization. Check relay contact wiring polarity and isolation requirements before applying customer power connections.
$200.00 $100.00
-
General Electric IS200VRTDH1DAA GE Mark VI RTD Input Board
GE IS200VRTDH1DAA Mark VI RTD Input Board The GE IS200VRTDH1DAA, also cataloged as the IS200VRTDH1DAA RTD Input Board, operates as a dedicated temperature acquisition hardware component for RTD signal conversion within the GE Mark VI VME control platform. It accepts 16 three-wire RTD inputs, performs 14-bit analog-to-digital conversion, and transfers temperature data through the VME backplane for turbine control monitoring. Hardware Specifications Parameter Specification Model IS200VRTDH1DAA Brand GE Product Type RTD Input Board System Platform Mark VI Speedtronic VME Control System Inputs 16 three-wire RTD channels Sensor Type Platinum RTD sensors, including Pt100 Excitation Current 10 mA DC multiplexed A/D Resolution 14-bit Mounting VME rack with front-panel screws Indicators 3 LED status indicators Isolation Channel-to-earth isolation Operating Temp -30 to +65 deg C Storage Temp -40 to +85 deg C Humidity 5% to 95% non-condensing RTD Signal Processing and VME Interface Characteristics The IS200VRTDH1DAA provides RTD measurement acquisition through multiplexed excitation and digital conversion circuitry. The board processes resistance variations from platinum RTD elements and outputs digitized temperature values through the Mark VI VME backplane communication path. The board supports simplex and TMR (Triple Modular Redundancy) configurations within Mark VI architectures. Firmware revision compatibility must be verified when replacing boards, as the D-rated revision and A-rated revisions have defined backward compatibility limitations. The hardware design includes conformal coating, EMI shielding, and vibration resistance features for turbine control cabinet installation. LED indicators provide local status information for board health monitoring. Firmware and Industrial Control Compatibility The GE Mark VI platform uses deterministic VME backplane communication for controller-to-I/O data exchange. The IS200VRTDH1DAA integrates with the Speedtronic control architecture through configured I/O addressing and board-level firmware functions. The board supports industrial control requirements including I/O density scaling within VME racks and compatibility verification across Mark VI hardware revisions. Proper firmware matching is required when integrating replacement modules into existing controller configurations. Frequently Asked Questions Q: How many RTD input channels are available on the IS200VRTDH1DAA?A: The board provides 16 three-wire RTD input channels for temperature signal acquisition. Q: What type of RTD sensors can be connected to this board?A: The module is designed for platinum RTD sensors, including Pt100 type sensors, with multiplexed 10 mA DC excitation. Q: Can the board operate in redundant configurations?A: The IS200VRTDH1DAA supports simplex and TMR configurations within GE Mark VI control architectures. Field Installation Guidelines Install the IS200VRTDH1DAA in the designated GE Mark VI VME rack location using the front-panel mounting hardware. Verify that RTD wiring is correctly terminated at the associated terminal boards before connecting field cables. Use shielded instrumentation wiring for RTD signal connections where required by site electrical standards. Maintain separation between low-level RTD signal cables and high-current power conductors to reduce electromagnetic interference. Confirm controller configuration, board revision compatibility, and I/O addressing before commissioning. Ensure grounding paths follow the cabinet design requirements for channel-to-earth isolation performance.
$200.00 $100.00
-
General Electric GE IS200EPCTG1AZZ Exciter PT/CT Terminal Board
GE IS200EPCTG1AZZ Exciter PT/CT Terminal Board The GE IS200EPCTG1AZZ, also cataloged as the IS200EPCT Exciter PT/CT Terminal Board, operates as a dedicated hardware component for generator voltage and current signal acquisition within GE EX2100 excitation control systems. The board receives PT/CT feedback, performs signal conditioning and isolation, and transfers scaled analog signals to the EMIO interface. Suffix Breakdown & Model Matrix Model Element Description IS200 GE Mark VI/EX2100 control hardware family EPCT Exciter PT/CT Terminal Board functional designation G1 Board hardware revision identifier AZZ Factory configuration and ordering suffix The IS200EPCTG1AZZ is configured as an EPCT terminal interface board for EX2100 excitation applications. The available configuration supports generator feedback measurement through PT and CT input circuits and provides conditioned outputs for excitation regulation processing. Hardware Specifications Parameter Specification Model IS200EPCTG1AZZ Brand GE Origin United States Weight 0.5 kg Dimensions 232 mm x 165 mm x 89 mm Operating Temp -40 deg C to +85 deg C Power Consumption Low-power signal conditioning and interface processing Module Type Exciter PT/CT Terminal Board Series EX2100 PT Inputs 2 x three-phase PT inputs, 115 V rms, 50/60 Hz CT Inputs 2 x CT inputs, 1 A or 5 A Analog Output 0-10 V or 4-20 mA Input Burden <= 1 VA Signal Isolation 500 Vrms Mounting Type EX2100 chassis backplane mount Wiring Capacity Up to #10 AWG Maximum Cable Length Up to 1000 ft Humidity Range 5%-95% non-condensing Compliance UL 508, IEC 61010-1, RoHS 3 Profinet and Industrial Control Signal Interface Characteristics The IS200EPCTG1AZZ provides generator feedback interface functions within the GE EX2100 excitation control architecture. The board converts PT voltage measurements and CT current feedback signals into conditioned analog outputs for EMIO board processing. The module applies signal isolation between measurement circuits and control interfaces. Its analog output scaling supports 0-10 V and 4-20 mA transmission formats used for excitation regulation feedback paths. The hardware design supports deterministic signal transfer between field measurement devices and the excitation controller. The EPCT board supports I/O density scaling within EX2100 configurations by providing multiple three-phase PT input channels and CT measurement inputs on a single terminal interface assembly. The module can be integrated into simplex and TMR excitation system configurations depending on system architecture requirements. Frequently Asked Questions Q: What type of feedback signals can the IS200EPCTG1AZZ process?A: The board processes generator PT voltage inputs and CT current inputs, providing conditioned analog outputs for excitation control processing. Q: What analog output signals are available from the EPCT board?A: The IS200EPCTG1AZZ provides scaled analog outputs in 0-10 V or 4-20 mA formats. Q: What isolation level is provided between signal circuits?A: The board provides 500 Vrms signal isolation between measurement circuits and interface paths. Field Installation Guidelines Install the IS200EPCTG1AZZ on the designated EX2100 chassis mounting location and verify terminal assignments before connecting PT and CT field wiring. Use appropriately rated wiring for generator voltage and current measurement circuits. Maintain separation between PT/CT signal cables and high-current power conductors to reduce electromagnetic interference. Terminate cable shields according to excitation cabinet grounding practices. Verify CT polarity, PT phase sequence, and terminal tightness before energizing the excitation system. Inspect board connectors, terminal blocks, and conformal-coated surfaces during installation. Confirm that wiring routing follows cabinet clearance and thermal management requirements.
$200.00 $100.00
-
General Electric IS200ECTBG2A GE EX2100 Exciter Contact Terminal Board
GE IS200ECTBG2A Exciter Contact Terminal Board Configured for contact signal termination and relay control execution in GE EX2100/EX2100e excitation control systems, the GE IS200ECTBG2A (IS200ECTB Exciter Contact Terminal Board) provides direct physical/electrical execution for auxiliary contact inputs, trip relay outputs, and general-purpose relay interfaces in simplex excitation architectures. Hardware Specifications Parameter Specification Model IS200ECTBG2A Brand GE Origin United States Weight 0.34 kg Dimensions 150 x 76 x 90 mm Operating Temp 0 deg C to +60 deg C Power Consumption Relay and contact interface board power consumption Module Type Exciter Contact Terminal Board (ECTB) Series EX2100 Operating Mode Simplex mode only Form Factor Exciter cabinet chassis-mounted terminal board Relay Control Voltage 24 VDC Customer Power Input 125 VDC Wetting Voltage 70 VDC (63-84 VDC range) Relay Configuration 2 Form-C trip relays and 4 Form-C general-purpose relays Auxiliary Inputs 6 powered/wetted auxiliary contact inputs Relay Contact Isolation 500 VDC channel-to-earth isolation Protection Features Conformal coating and LED status indicators EtherNet/IP and Industrial Control Signal Interface Characteristics The IS200ECTBG2A is designed for GE EX2100 excitation control architectures and performs discrete signal termination between field contacts, relay circuits, and the excitation controller interface. The board routes auxiliary contact inputs and relay outputs associated with generator breaker monitoring, lockout functions, and auxiliary sequencing circuits. The EX2100 ECTB interface uses dedicated relay and contact circuits rather than analog measurement channels. The board supports simplex execution only, with the G2 configuration identifying single-channel operation. Relay outputs include two Form-C trip relays for protection-related circuits and four Form-C general-purpose relays for auxiliary control functions. The module follows GE industrial control hardware practices including conformal PCB coating, electrical isolation between relay circuits and earth reference, and compatibility with excitation cabinet wiring structures. The contact interface design supports discrete I/O density scaling within the EX2100 excitation platform. Frequently Asked Questions Q: What operating architecture is supported by the IS200ECTBG2A?A: The IS200ECTBG2A supports simplex mode operation only and is configured for single-channel EX2100 excitation system installations. Q: What type of relay outputs are provided on the ECTB board?A: The board provides two Form-C trip relay outputs and four Form-C general-purpose Form-C relay outputs for discrete control circuits. Q: What field input signals can be connected to the IS200ECTBG2A?A: The board supports six powered/wetted auxiliary contact inputs, including monitored signals such as generator breaker and lockout status contacts. Field Installation Guidelines Install the IS200ECTBG2A in the designated EX2100 excitation cabinet location and verify terminal assignments against the GEH-6632 instruction manual before field wiring. Use properly rated field wiring for 125 VDC customer power circuits and relay contact connections. Separate low-level signal wiring from high-current switching conductors to reduce electrical interference. Terminate cable shields according to cabinet grounding practices where shielded wiring is applied. Verify relay contact polarity, auxiliary input wiring, and protective earth connections before applying system power. Inspect terminal blocks, board connectors, and conformal-coated surfaces during installation to ensure no mechanical damage or contamination is present.
$200.00 $100.00
-
GE IS210SAMBH2AA GE Mark VI Servo Amplifier Module
GE IS210SAMBH2AA Mark VI Servo Amplifier Module The GE IS210SAMBH2AA, also cataloged as the IS210SAMB Servo Amplifier Module, operates as a dedicated hardware component for hydraulic actuator current control within the GE Speedtronic Mark VI turbine control system. The module converts digital commands into proportional servo valve drive current with LVDT feedback processing. Hardware Specifications Parameter Specification Model IS210SAMBH2AA Brand GE Origin United States Weight 0.35 kg Operating Temp -30 to +65 deg C Power Consumption Supplied by +28 VDC nominal input Product Type Servo Amplifier Modules Function Servo amplifier for hydraulic actuators Inputs LVDT feedback signals, up to 2 channels Outputs +/-200 mA current drive for servo valves Resolution 16-bit digital-to-analog conversion Accuracy +/-0.1% of full scale Communication Interface Mark VI controller backplane interface Mounting Rack mount, Mark VI chassis compatible PCB Protection Conformal coating Deterministic Servo Control and Actuator Feedback Processing The IS210SAMBH2AA applies GE Mark VI industrial control architecture for closed-loop hydraulic actuator control. The module receives digital control signals from the controller, converts them into proportional current outputs, and drives servo valves connected to turbine actuators. The Mark VI platform supports deterministic controller communication and I/O density scaling through modular hardware structures. The servo amplifier module processes LVDT feedback signals to maintain actuator position control loops. Firmware flash compatibility must correspond with the installed Mark VI controller hardware revision and system configuration. Frequently Asked Questions Q: What type of actuator interface does the IS210SAMBH2AA provide?A: The module provides proportional current drive outputs for hydraulic servo valves, with outputs rated at +/-200 mA. Q: How does the module process valve position feedback?A: The IS210SAMBH2AA accepts LVDT feedback signals and integrates them into closed-loop actuator control functions. Q: Is the module compatible with redundant Mark VI configurations?A: The module supports Mark VI system architectures including simplex and TMR (Triple Modular Redundancy) configurations. Field Installation Guidelines Install the IS210SAMBH2AA in the assigned Mark VI rack position and verify proper mechanical seating with the chassis backplane connector. Check servo valve wiring polarity, LVDT feedback connections, and actuator loop configuration before system startup. Keep feedback and current drive wiring separated from high-voltage switching circuits to reduce electrical interference. Use shielded cables where required and terminate cable shields according to site grounding practices. Inspect rack mounting, backplane engagement, and grounding continuity before applying operating power.
$200.00 $100.00
-
General Electric IS210AEBIH2B GE Mark VI AE Bridge Interface Module
GE IS210AEBIH2B AE Bridge Interface Module The GE IS210AEBIH2B, also identified as the IS210AEBI AE Bridge Interface Module, provides hardware-level communication interface functions within GE Mark VI/Mark VIe turbine control platforms. The module performs data routing, synchronization, and diagnostic signal exchange between controllers, I/O subsystems, and the VME backplane through a 24 VDC powered industrial PCB assembly. Hardware Specifications Parameter Specification Model IS210AEBIH2B Brand GE Origin United States Weight 0.7 kg Dimensions 160 mm x 100 mm x 80 mm Operating Temp -40 deg C to +70 deg C Power Consumption Low-power communication/interface processing module Module Type AE Bridge Interface Module (AEBI) System Platform GE Mark VI / Mark VIe Speedtronic control system Form Factor VME rack-mounted PCB module Operating Voltage 24 VDC system supply Communication Interface VME backplane and internal turbine control network Isolation Galvanic isolation and EMI protection Cooling Method Passive convection cooling PCB Protection Conformal coating Configuration Support Simplex, redundant, and TMR configurations Humidity Range 5%-95% non-condensing Industrial Control Network Interface Characteristics The IS210AEBIH2B operates as an AE Bridge Interface Module within the GE Mark VI/Mark VIe architecture. The board manages communication paths between control processors, turbine I/O assemblies, and the VME backplane. Its hardware design supports synchronization and diagnostic data transfer required for coordinated turbine control operations. The module supports simplex, redundant, and triple modular redundancy (TMR) configurations. In redundant control architectures, the AEBI interface maintains communication availability between processing units and distributed control elements through coordinated data exchange paths. The PCB assembly incorporates conformal coating and EMI shielding features for operation in industrial electrical environments. The module design supports signal integrity by reducing the effects of contamination, moisture exposure, and electromagnetic interference on board-level communication circuits. Frequently Asked Questions Q: What communication interfaces are supported by the IS210AEBIH2B?A: The module communicates through the GE Mark VI/Mark VIe VME backplane and internal turbine control network interfaces for controller and I/O subsystem data exchange. Q: Does the IS210AEBIH2B support redundant control configurations?A: Yes. The module supports simplex, redundant, and TMR system configurations within compatible GE Speedtronic control architectures. Q: What protection features are included on the PCB assembly?A: The module includes conformal coating, EMI shielding provisions, and passive convection cooling design for industrial control cabinet installation. Field Installation Guidelines Install the IS210AEBIH2B in the designated GE Mark VI/Mark VIe VME rack position according to the system hardware configuration. Verify that the backplane connector is correctly aligned before insertion and avoid mechanical stress on the PCB assembly. Use shielded signal wiring where applicable and maintain separation between communication cables and high-voltage power conductors to reduce electromagnetic interference. Ensure cabinet grounding provides a low-impedance path for shield termination and equipment protective bonding. Before replacement or maintenance work, confirm system power isolation procedures are completed. Inspect the module edge connectors, rack contacts, and cooling airflow paths for contamination or physical damage prior to installation.
$200.00 $100.00
-
General Electric GE IS420ESWAH2A Ethernet Switch Assembly Module
GE IS420ESWAH2A Ethernet Switch Assembly Module The GE IS420ESWAH2A, also cataloged as the IS420ESWAH2A Ethernet Switch Assembly Module, operates as a dedicated hardware component for managed Ethernet communication routing within the GE Mark VIe turbine control system. It provides physical network switching between controllers, I/O packs, and operator interface devices. Hardware Specifications Parameter Specification Model IS420ESWAH2A Brand GE Origin United States Weight 0.45 kg Operating Temp -30 to +65 deg C Power Consumption Powered by 24 VDC nominal supply Product Type Ethernet Switch Assembly Modules System Platform GE Mark VIe Speedtronic Control System Switch Type Managed industrial Ethernet switch Ethernet Ports 8 x 10/100 Mbps RJ-45 ports Supported Protocols TCP/IP, Modbus TCP, GE proprietary I/O bus Redundancy Features Dual power supply inputs and redundant communication paths Mounting Method DIN rail or panel mounting PCB Protection Conformal coating for dust and humidity resistance Humidity Range 5-95% non-condensing GE Mark VIe Industrial Ethernet Communication Characteristics The IS420ESWAH2A provides managed Ethernet switching functions for Mark VIe deterministic network architectures. The module supports Ethernet communication paths between controller assemblies, distributed I/O packs, and operator interface systems through configured network connections. The switch assembly supports industrial control network expansion through Ethernet port density scaling and redundant communication path management. Firmware flash compatibility allows the module to maintain supported configuration functions within the Mark VIe platform. Network traffic handling includes TCP/IP, Modbus TCP, and GE proprietary I/O bus communication protocols. Dual power inputs and redundant communication structures provide continuous network connectivity during configured fault conditions. Frequently Asked Questions Q: How many Ethernet ports are available on the IS420ESWAH2A?A: The module provides 8 RJ-45 Ethernet ports supporting 10/100 Mbps communication. Q: What power supply configuration does the IS420ESWAH2A support?A: The switch assembly operates with a 24 VDC nominal supply and supports dual power supply inputs for redundant configurations. Q: Can the IS420ESWAH2A communicate with Mark VIe I/O packs?A: Yes. The module provides Ethernet switching between Mark VIe controllers, I/O packs, and connected operator interface devices. Field Installation Guidelines Install the IS420ESWAH2A on the designated DIN rail or panel mounting location inside the Mark VIe control cabinet. Verify that Ethernet cables are connected to the correct network ports according to the cabinet wiring documentation. Use industrial Ethernet cables with appropriate shielding and maintain separation between communication wiring and high-voltage power conductors. Connect cable shields according to the site grounding standard to reduce electromagnetic interference. Verify 24 VDC power polarity before energizing the module. Confirm Ethernet link status, communication paths, and controller network recognition through the Mark VIe diagnostic interface before system operation.
$200.00 $100.00
-
General Electric GE IS220PTCCH2A Thermocouple Input Pack Module
GE IS220PTCCH2A Thermocouple Input Pack Module Configured for thermocouple signal acquisition in the GE Mark VIe turbine control system, the GE IS220PTCCH2A (IS220PTCCH2A Thermocouple Input Pack Module) provides direct physical/electrical execution for temperature signal conditioning, conversion, and isolated communication with Mark VIe controller networks. Hardware Specifications Parameter Specification Model IS220PTCCH2A Brand GE Origin United States Weight 0.35 kg Operating Temp -30 to +65 deg C Power Consumption Powered by +28 VDC nominal supply Product Type Thermocouple Input Pack Modules System Platform GE Mark VIe Speedtronic Control System Input Channels 12 thermocouple inputs Supported Thermocouple Types Type E, J, K, N, R, S, T, B A/D Conversion Resolution 16-bit Temperature Accuracy +/- 1 deg C typical Cold Junction Compensation Integrated automatic CJC Isolation Channel-to-channel and channel-to-system isolation Communication Interface Ethernet connection to Mark VIe controller Mounting Method DIN rail or panel mounting PCB Protection Conformal coating GE Mark VIe Thermocouple Signal Processing Characteristics The IS220PTCCH2A performs thermocouple signal conditioning through integrated analog processing, cold junction compensation (CJC), and digital conversion functions. The module transfers processed temperature data through Ethernet communication to the Mark VIe controller architecture. The module supports industrial control network configurations with simplex and TMR (Triple Modular Redundancy) operation. The onboard identification chip provides automatic hardware recognition during controller configuration. Firmware flash compatibility allows the input pack to maintain configuration consistency within supported Mark VIe control environments. The 12-channel I/O density supports multi-point temperature monitoring with isolated measurement paths for thermocouple field circuits. Frequently Asked Questions Q: What thermocouple types are supported by the IS220PTCCH2A?A: The module supports Type E, J, K, N, R, S, T, and B thermocouple inputs. Q: Does the IS220PTCCH2A provide cold junction compensation?A: Yes. The module includes integrated automatic cold junction compensation for thermocouple measurement processing. Q: Can the IS220PTCCH2A operate in redundant Mark VIe configurations?A: Yes. The module supports simplex and TMR system configurations within the Mark VIe control architecture. Field Installation Guidelines Install the IS220PTCCH2A on the designated DIN rail or panel mounting location according to the Mark VIe cabinet layout. Connect thermocouple field wiring to the assigned input terminals while maintaining correct polarity and sensor type configuration. Use shielded signal cables where required by site grounding practices. Separate thermocouple wiring from high-voltage power cables and high-current switching circuits to reduce electrical interference. Verify Ethernet communication connections and module identification before system commissioning. Confirm that the field wiring configuration matches the configured thermocouple type before enabling temperature measurement functions.
$200.00 $100.00
-
General Electric IS210AEBIH1B GE Mark VI Analog Expansion Board
GE IS210AEBIH1B Mark VI Analog Expansion Board Module The GE IS210AEBIH1B, also cataloged as the IS210AEBI Analog Expansion Board Module, operates as a dedicated hardware component for analog channel expansion and signal conversion within the GE Speedtronic Mark VI turbine control system. The module provides additional analog input and output processing through the controller backplane interface. Hardware Specifications Parameter Specification Model IS210AEBIH1B Brand GE Origin United States Weight 0.35 kg Operating Temp -30 to +65 deg C Power Consumption Supplied by +28 VDC nominal input Product Type Analog Expansion Modules Analog Inputs 8 channels, configurable for 4-20 mA or +/-10 VDC Analog Outputs 4 channels, 4-20 mA Resolution 16-bit A/D and D/A conversion Accuracy +/-0.1% of full scale Isolation Channel-to-channel and channel-to-system isolation Communication Interface Mark VI controller backplane interface Mounting Rack mount, Mark VI chassis compatible PCB Protection Conformal coating Industrial Control Backplane and I/O Density Scaling The IS210AEBIH1B extends analog signal capacity within the GE Mark VI control architecture. The module performs signal conditioning, conversion, and electrical isolation between field instrumentation and controller processing units. The Mark VI platform uses modular I/O expansion structures to increase channel availability. The AEBI module supports I/O density scaling through additional analog channels while maintaining communication through the controller backplane. Firmware flash compatibility must match the installed Mark VI hardware revision and controller configuration. Frequently Asked Questions Q: What is the primary function of the IS210AEBIH1B module?A: The IS210AEBIH1B provides additional analog input and output capacity for the GE Mark VI control system, including signal conditioning and conversion functions. Q: Which analog signals are supported by this module?A: The module supports configurable analog inputs of 4-20 mA and +/-10 VDC, with 4-20 mA analog outputs. Q: Does the IS210AEBIH1B support redundant Mark VI configurations?A: The module is designed for Mark VI system configurations supporting simplex and TMR (Triple Modular Redundancy) architectures. Field Installation Guidelines Install the IS210AEBIH1B module in the specified Mark VI rack position and confirm correct mechanical alignment with the chassis interface before energizing the system. Verify analog channel configuration, field wiring polarity, and terminal assignments according to the system drawings. Keep analog signal cables separated from high-current switching lines and power conductors to reduce electromagnetic interference. Use shielded instrumentation cables where required and connect cable shields according to the site grounding standard. Check rack mounting hardware, backplane engagement, and grounding continuity during installation inspection.
$200.00 $100.00
-
General Electric IS200SSCAH1ABA GE Mark VI Analog Module
GE IS200SSCAH1ABA Mark VI Static Source Control Analog Module Configured for analog signal conditioning and conversion in GE Speedtronic Mark VI control systems, the GE IS200SSCAH1ABA (IS200SSCA Analog Module) provides direct physical/electrical execution for field signal acquisition, isolation, and output processing. The module handles current and voltage channels through VME backplane communication with Mark VI controllers. Suffix Breakdown & Model Matrix The IS200SSCAH1ABA model is identified as a GE Mark VI Static Source Control Analog (SSCA) module. The available provided data defines the complete ordering code only; no additional manufacturer-published suffix expansion is specified. Model Description IS200SSCAH1ABA Static Source Control Analog module IS200SSCA Base module family identifier Mark VI GE Speedtronic turbine control platform Hardware Specifications Parameter Specification Model IS200SSCAH1ABA Brand GE Origin United States Weight 0.35 kg Operating Temp -30 to +65 deg C Power Consumption Supplied by +28 VDC nominal input Product Type Analog Interface Modules Analog Inputs 8 channels, configurable for 4-20 mA or +/-10 VDC Analog Outputs 4 channels, 4-20 mA Resolution 16-bit A/D and D/A conversion Accuracy +/-0.1% of full scale Isolation Channel-to-channel and channel-to-system isolation Communication Interface VME backplane interface to Mark VI controller Mounting Mark VI rack mount chassis compatible PCB Protection Conformal coating Mark VI Analog Signal Processing and I/O Scaling The IS200SSCAH1ABA applies GE industrial control architecture for analog I/O processing within the Mark VI platform. The module performs signal conditioning, analog conversion, and electrical isolation between field devices and controller processing circuits. The Mark VI system supports I/O density scaling through modular hardware configurations. The SSCA module communicates through the VME backplane structure, maintaining deterministic data exchange between analog channels and the controller layer. Firmware flash compatibility must follow the installed Mark VI controller configuration and approved hardware revision requirements. Frequently Asked Questions Q: What type of field signals can the IS200SSCAH1ABA process?A: The module processes analog current and voltage signals, including 4-20 mA and +/-10 VDC configurable inputs with 4-20 mA outputs. Q: Does the IS200SSCAH1ABA provide electrical isolation for analog channels?A: Yes. The module provides channel-to-channel and channel-to-system isolation for analog signal separation. Q: What communication interface connects this module to the controller?A: The IS200SSCAH1ABA uses a VME backplane interface for communication with the GE Mark VI controller. Field Installation Guidelines Install the IS200SSCAH1ABA in the designated Mark VI rack position and verify mechanical engagement with the chassis connector before system power application. Confirm field wiring configuration, signal polarity, and channel assignments according to the control system drawings. Route analog signal cables separately from high-voltage and high-current conductors to reduce electromagnetic interference. Use shielded instrumentation wiring where required and terminate cable shields according to the site grounding practice. Verify backplane connections, rack seating, and grounding continuity before commissioning the module.
$200.00 $100.00
Anda telah melihat 456 dari 1313 produk