Sensor dan probe menyediakan pemantauan yang akurat untuk peralatan industri. Produk kami mencakup probe getaran, jarak, dan perpindahan dari produsen terkemuka. Kami menyediakan model yang masih ada maupun yang sudah dihentikan produksinya dengan dukungan global yang tepercaya.
Sensor dan Probe
-
Bently Nevada Bently Nevada 330104-00-08-50-12-00 3300 XL 8 mm Proximity Probe
Bently Nevada 330104-00-08-50-12-00 3300 XL 8 mm Proximity Probe The Bently Nevada 330104-00-08-50-12-00, also cataloged as the 330104 3300 XL 8 mm Proximity Probe, operates as a dedicated eddy-current measurement component for shaft displacement and vibration monitoring within the 3300 XL Transducer System. Hardware Specifications Parameter Specification Model 330104-00-08-50-12-00 Brand Bently Nevada Dimensions Overall case length: 80 mm; total cable length: 5.0 m Operating Temp -51 deg C to +177 deg C Power Consumption Supplied through compatible Proximitor sensor system; probe is a passive sensing element Product Series 3300 XL 8 mm Proximity Transducer System Probe Diameter 8 mm Thread Type M10 x 1 metric thread Unthreaded Length 00 option; fully threaded case Case Material AISI 303 or 304 stainless steel Tip Material Polyphenylene Sulfide (PPS) Cable Type FluidLoc cable with flexible stainless steel armor Connector Type Miniature coaxial ClickLoc connector Linear Range 2 mm (80 mils) Scale Factor 7.87 V/mm (200 mV/mil) nominal Pressure Seal Viton O-ring between probe tip and case Agency Approval Standard configuration; no agency approval option Eddy-Current Measurement and Rotor Dynamics Characteristics The 330104-00-08-50-12-00 uses an eddy-current sensing principle to measure shaft position changes without mechanical contact. Therefore, the probe provides proportional output changes according to the target surface displacement relative to the probe tip. The 3300 XL system applies calibrated eddy-current probe scaling with a nominal scale factor of 7.87 V/mm (200 mV/mil). In addition, the measurement circuit supports gap voltage validation by maintaining probe operating conditions around the standard -10 VDC target range used for Bently Nevada proximity monitoring systems. The armored FluidLoc cable construction reduces mechanical damage risks during installation. Furthermore, the ClickLoc connector provides a controlled coaxial connection path to maintain signal integrity in rotating machinery monitoring applications. The probe configuration supports rotor dynamics analysis by providing displacement feedback for vibration amplitude, shaft position, and mechanical movement evaluation. The sensor installation should maintain proper probe orientation and cable routing to reduce external interference and signal distortion. Frequently Asked Questions Q: What measurement principle does the 330104-00-08-50-12-00 use?A: The probe uses eddy-current technology to measure shaft displacement and vibration through a non-contact electromagnetic field. Q: Can the probe be directly connected to a monitoring system input?A: No. The probe requires a compatible 3300 XL Proximitor sensor module to generate the conditioned monitoring signal. Q: Does the armored cable affect probe installation requirements?A: The armored cable improves mechanical protection, but installers must still maintain proper routing, grounding, and separation from high-noise electrical conductors. Field Installation Guidelines Install the M10 x 1 threaded probe into the prepared mounting location using the specified mechanical interface. Verify probe tip clearance and target surface condition before commissioning the measurement loop. Maintain cable routing practices that separate the probe cable from high-current power wiring and electromagnetic noise sources. Connect the miniature coaxial ClickLoc connector securely to maintain signal continuity. Verify the operating gap voltage after installation. The standard Bently Nevada commissioning practice uses gap voltage checks near the -10 VDC target range. Ensure the stainless steel armor does not create unintended mechanical stress at the connector or probe body. Confirm the probe output response with the associated Proximitor module before placing the machinery protection channel into service.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330103-00-07-20-02-CN 3300 XL 8 mm Proximity Probe
Bently Nevada 330103-00-07-20-02-CN 3300 XL 8 mm Proximity Probe Configured for eddy-current displacement measurement in the 3300 XL Eddy Current Transducer System, the Bently Nevada 330103-00-07-20-02-CN (330103 3300 XL 8 mm Proximity Probe) provides direct physical measurement of shaft position and vibration movement through a non-contact sensing circuit. Hardware Specifications Parameter Specification Model 330103-00-07-20-02-CN Brand Bently Nevada Product Type 3300 XL 8 mm Proximity Probe Origin USA Dimensions Overall case length: 70 mm; Total length: 2.0 m Operating Temp -51 deg C to +177 deg C Power Consumption Powered by compatible proximity system driver; probe passive sensing element Thread Type M10x1 metric thread Probe Construction Without armor casing Probe Tip Material Polyphenylene sulfide (PPS) Probe Case Material AISI 304 stainless steel Cable Type Standard 75 ohm coaxial cable with CableLoc design Cable Pull Strength 330 N Connector Type Gold-plated miniature coaxial ClickLoc connector Linear Range 2.0 mm (80 mils) Measurement Starting Point 0.25 mm (10 mils) from target Average Scale Factor 7.87 V/mm nominal Target Material AISI 4140 steel Frequency Response 0 Hz to 10 kHz (+0, -3 dB) Humidity Rating 100% condensing, non-submerged when properly sealed Approval Option CN country-specific approval Eddy-Current Measurement and Rotor Dynamics Characteristics The 330103-00-07-20-02-CN uses eddy-current probe scaling to convert shaft displacement into proportional electrical output signals. The probe system measures dynamic shaft movement and static position changes through the interaction between the probe tip electromagnetic field and the conductive target surface. Furthermore, the probe output requires gap voltage validation during commissioning. Bently Nevada proximity systems typically verify the probe operating point near the -10 VDC target region to confirm correct physical installation and signal range. The probe supports rotor dynamics analysis by providing vibration displacement data from rotating shafts. Therefore, correct probe gap setting, target material compatibility, and cable routing directly affect measurement accuracy. The miniature coaxial ClickLoc connector and CableLoc design maintain signal integrity by reducing mechanical cable movement influence. In addition, proper installation practices help reduce signal interference and cross-talk effects in multi-probe monitoring arrangements. Frequently Asked Questions Q: What measurement principle does the 330103-00-07-20-02-CN use?A: The probe uses an eddy-current sensing principle to measure the distance between the probe tip and a conductive rotating shaft surface. The system converts displacement changes into proportional electrical signals. Q: What cable and connector configuration does this probe include?A: This model uses a 2.0 m standard 75 ohm coaxial cable with a miniature coaxial ClickLoc connector and CableLoc retention design. Q: What target material is required for calibration?A: The specified target material is standard AISI 4140 steel. Calibration values may change when different conductive target materials are used. Field Installation Guidelines Install the probe with the M10x1 metric thread connection according to the mechanical mounting requirements of the monitored machine. Maintain the recommended probe gap position before final system calibration. Verify the electrical gap voltage during commissioning. Bently Nevada systems normally validate operation near the -10 VDC target range. Route the coaxial cable away from high-current power conductors and strong electromagnetic interference sources. Ensure the cable shielding and connector installation follow the monitoring system grounding requirements. Avoid sharp cable bending points to prevent mechanical stress on the coaxial cable assembly. Confirm that the probe tip faces the correct shaft target surface and maintains proper alignment with the measurement axis
$200.00 $100.00
-
Bently Nevada 330103-00-10-05-02-00 | 3300 XL 8 mm Proximity Probe | Bently Nevada
Bently Nevada 330103-00-10-05-02-00 3300 XL 8 mm Proximity Probe Configured for shaft displacement measurement in the 3300 XL Proximity Transducer System, the Bently Nevada 330103-00-10-05-02-00 (330103 3300 XL 8 mm Proximity Probe) provides direct physical measurement through an eddy-current sensing circuit. The probe uses an M10 x 1 metric thread, 100 mm case length, 0 mm unthreaded length, and a 0.5 meter miniature coaxial ClickLoc connector standard cable. Hardware Specifications Parameter Specification Model 330103-00-10-05-02-00 Brand Bently Nevada Product Type 3300 XL 8 mm Proximity Probe Origin USA Weight 0.06 kg Dimensions 115.5 x 1.5 x 2 cm estimated shipping size Power Consumption Passive eddy-current probe, powered by compatible proximity transducer system Probe Type Eddy-current non-contact displacement sensor Probe Diameter 8 mm Thread Configuration M10 x 1 metric thread Armor Type Without armor Minimum Unthreaded Length 0 mm Case Length 100 mm Total Length Option 0.5 meter (1.6 feet) Cable Type Miniature coaxial ClickLoc connector standard cable Connector Option 02 Agency Approval Not required Tariff Code 8537101190 Eddy-Current Probe Scaling and Rotor Dynamics Characteristics The Bently Nevada 330103 series applies eddy-current probe scaling principles to convert shaft-to-probe distance variations into electrical displacement signals. The probe operates as part of a matched proximity measurement chain, where the driver, extension cable, and monitoring module determine calibration accuracy. The probe supports rotor dynamics monitoring by providing non-contact shaft displacement feedback. Therefore, the system can evaluate radial vibration, axial position, and mechanical movement behavior when connected to compatible Bently Nevada monitoring hardware. The probe installation requires correct gap voltage validation. The typical Bently Nevada proximity measurement system uses -10 VDC target gap voltage during calibration to establish the required operating range between the probe tip and the rotating shaft surface. The miniature coaxial ClickLoc cable design maintains signal integrity between the probe and connected transducer electronics. In addition, proper cable routing reduces electrical interference and helps maintain stable displacement measurements. Frequently Asked Questions Q: What measurement principle does the 330103-00-10-05-02-00 use?A: The probe uses eddy-current sensing technology to measure the distance between the probe tip and the conductive shaft target without mechanical contact. Q: Does this model include an armored probe design?A: No. The 330103-00-10-05-02-00 uses a non-armored construction with an M10 x 1 metric thread configuration. Q: What cable connection does this probe provide?A: This model uses a miniature coaxial ClickLoc connector with a standard 0.5 meter cable length option. Field Installation Guidelines Install the probe with the specified M10 x 1 thread engagement and ensure the sensing tip faces the target shaft surface correctly. Maintain proper mechanical alignment between the probe tip and the rotating component. Avoid excessive vibration, impact loading, or mechanical stress on the probe body and cable connection. Route the miniature coaxial cable separately from high-current power conductors to reduce electrical noise coupling. Ground cable shields according to the monitoring system installation requirements. During commissioning, verify the probe gap voltage and confirm the expected displacement signal response through the connected Bently Nevada proximity monitoring channel.
$200.00 $100.00
-
Bently Nevada 330103-00-12-10-02-00 | Bently Nevada | 3300 XL 8 mm Proximity Probes
Bently Nevada 330103-00-12-10-02-00 3300 XL 8 mm Proximity Probes The Bently Nevada 330103-00-12-10-02-00, also cataloged as the 330103 3300 XL 8 mm Proximity Probe, operates as a dedicated hardware component for non-contact shaft displacement measurement within the 3300 XL Proximity Transducer System. Hardware Specifications Parameter Specification Model 330103-00-12-10-02-00 Brand Bently Nevada Product Type 3300 XL 8 mm Proximity Probe Origin USA Weight 0.05 kg Dimensions 1.8 x 1.6 x 113 cm estimated shipping size Operating Temp Compatible with 3300 XL system operating requirements; specific temperature range not provided Power Consumption Supplied through compatible Proximitor sensor; specific probe consumption not provided Thread Type M10 x 1 thread Armor Type Without armor Unthreaded Length 0 mm Overall Case Length 120 mm Total Length 1.0 meter (3.3 feet) Connector Type Miniature coaxial ClickLoc connector standard cable Extension Cable Compatibility 3300 XL 8 mm system interchangeable cabling Tariff Code 8537101190 Shipment Location Xiamen, China Eddy Current Probe Scaling and Rotor Dynamics Characteristics The 330103-00-12-10-02-00 uses an eddy-current measurement principle to detect shaft displacement without physical contact. The probe generates an electromagnetic field at the sensing tip, and the system converts the changing gap distance into a proportional electrical signal. Furthermore, the 3300 XL 8 mm system supports rotor dynamics monitoring by providing stable displacement measurements for vibration analysis, shaft position monitoring, and mechanical movement evaluation. The system design supports interchangeability between probes, extension cables, and Proximitor sensors without individual component bench calibration. The probe system maintains measurement performance through controlled probe geometry, cable characteristics, and sensor matching. Additionally, installation practices must maintain proper signal integrity to prevent external interference and measurement deviation. Frequently Asked Questions Q: What measurement principle does the 330103-00-12-10-02-00 use?A: The probe uses eddy-current technology to measure the distance between the probe tip and the conductive shaft target without mechanical contact. Q: Is the 330103-00-12-10-02-00 compatible with armored installations?A: No. This specific configuration is supplied without armor and uses a miniature coaxial ClickLoc connector standard cable. Q: Does the probe require individual calibration with extension cables?A: No. The 3300 XL 8 mm system supports interchangeability of compatible probes, extension cables, and Proximitor sensors without individual matching procedures. Field Installation Guidelines Install the probe with the specified M10 x 1 thread engagement and ensure mechanical fixation prevents movement during machine operation. Maintain correct probe tip orientation toward the measurement target surface. Route probe cables separately from high-voltage power cables and strong electromagnetic interference sources. Connect cable shielding according to the applicable monitoring system grounding requirements. Verify the electrical gap voltage after installation when commissioning the complete proximity measurement channel. Inspect connector locking conditions to ensure the ClickLoc connection remains mechanically secured during operation. Confirm the probe, extension cable, and Proximitor sensor combination matches the configured 3300 XL 8 mm system requirements.
$200.00 $100.00
-
Bently Nevada 3300 XL 8 mm Proximity Probe | Bently Nevada | 330103-03-09-10-02-00
Bently Nevada 330103-03-09-10-02-00 3300 XL 8 mm Proximity Probe Configured for shaft displacement and vibration measurement in the 3300 XL 8 mm Proximity Transducer System, the Bently Nevada 330103-03-09-10-02-00 (330103 3300 XL 8 mm Proximity Probe) provides direct eddy-current sensing execution for mechanical position monitoring. Hardware Specifications Parameter Specification Model 330103-03-09-10-02-00 Brand Bently Nevada Product Type 3300 XL 8 mm Eddy Current Proximity Probe Origin USA Operating Temp -52 deg C to +177 deg C Power Consumption Supplied by compatible 3300 XL Proximitor Sensor system Probe Tip Diameter 8.0 mm Thread Type M10 x 1 metric thread Unthreaded Length 30 mm Case Length 90 mm Total Lead Length 1.0 meter Armor Type None Connector Type Miniature Coaxial ClickLoc connector Probe Tip Material Polyphenylene Sulfide (PPS) Probe Body Material AISI 303 / 304 Stainless Steel System Compatibility Bently Nevada 3300 XL 8 mm Transducer System Target Material 4140 Steel calibration target Linear Range 2.0 mm Sensitivity 7.87 V/mm nominal Scale Factor 200 mV/mil nominal Linearity Within +/- 0.025 mm Frequency Response 0 Hz DC to 10 kHz Output Resistance 75 ohm coaxial system Pressure Rating Sealed to 50 psi differential pressure across tip Standards Compliance API 670 mechanical configuration and temperature stability requirements Eddy Current Signal Scaling and Rotor Dynamics Monitoring The Bently Nevada 330103-03-09-10-02-00 uses an eddy-current measurement principle to convert probe gap variation into proportional electrical output. Therefore, the probe maintains a nominal scale factor of 200 mV/mil for shaft displacement analysis. The 3300 XL 8 mm probe architecture supports gap voltage validation with compatible Proximitor Sensor modules. During commissioning, technicians verify the operating gap position against the -10 VDC target reference used in Bently Nevada vibration monitoring systems. Furthermore, the probe supports rotor dynamics analysis by providing DC position and AC vibration signals. The non-contact sensing structure allows measurement of radial vibration, axial position, Keyphasor applications, and rotating equipment shaft behavior. The ClickLoc connector and probe construction reduce mechanical signal interruption caused by vibration environments. In addition, the probe design maintains signal integrity through controlled coaxial transmission characteristics. Frequently Asked Questions Q: What system accepts the 330103-03-09-10-02-00 probe output?A: The probe operates with the Bently Nevada 3300 XL 8 mm Proximitor Sensor system and requires a compatible extension cable and monitoring module configuration. Q: Can this probe measure both static position and dynamic vibration signals?A: Yes. The eddy-current probe provides both DC gap position measurement and AC dynamic displacement measurement for shaft monitoring applications. Q: What installation factors affect measurement accuracy?A: Probe mounting position, target surface condition, cable routing, connector locking, and correct gap voltage adjustment affect signal accuracy. Field Installation Guidelines Install the probe with the specified M10 x 1 mounting thread and maintain mechanical alignment between the probe tip and rotating shaft target surface. Route the coaxial cable away from high-current power conductors and electromagnetic interference sources. Maintain proper connector engagement and verify the ClickLoc locking mechanism after installation. Before operation, confirm the probe gap voltage through the connected Proximitor Sensor. Adjust the installation position to achieve the required measurement range and verify stable output during machine rotation. Avoid mechanical impact on the PPS probe tip and protect the cable from excessive bending or pulling forces during installation.
$200.00 $100.00
-
Bently Nevada 330103-05-15-10-02-00 | Bently Nevada | 3300 XL 8 mm Proximity Probe
Bently Nevada 330103-05-15-10-02-00 3300 XL 8 mm Proximity Probe The Bently Nevada 330103-05-15-10-02-00, also cataloged as the 330103 3300 XL 8 mm Proximity Probe, operates as a dedicated hardware component for eddy-current displacement measurement and rotor position monitoring within the 3300 XL Proximity Transducer System. Hardware Specifications Parameter Specification Model 330103-05-15-10-02-00 Brand Bently Nevada Product Type 3300 XL 8 mm Eddy Current Proximity Probe Origin USA Dimensions Unthreaded length: 50 mm; Overall case length: 150 mm; Cable length: 1.0 m Operating Temp -51 deg C to +177 deg C Power Consumption Supplied by compatible Proximity Transducer System driver module Probe Diameter 8 mm Measurement Principle Eddy current non-contact displacement sensing Thread Type M10 x 1 Target Material Conductive metal, standard calibration with AISI 4140 steel Linear Measurement Range 2.0 mm (80 mils) Linearity Range Starts at 0.25 mm (10 mils) from probe tip Average Scale Factor 7.87 V/mm (200 mV/mil) nominal Probe Tip Material Polyphenylene Sulfide (PPS) Case Material AISI 303 / 304 Stainless Steel Connector Type Gold-plated ClickLoc coaxial connector Cable Type Standard miniature coaxial cable Cable Pull Strength 330 N maximum force at probe tip attachment Eddy Current Scaling and Rotor Dynamics Monitoring The 330103 series probe converts shaft displacement changes into electrical signals through eddy-current measurement technology. Therefore, the probe maintains a defined scale factor for vibration and position analysis when paired with a compatible Bently Nevada Proximitor module. The probe supports rotor dynamics applications by measuring radial shaft vibration, axial thrust position, and Keyphasor reference signals. Additionally, proper gap voltage validation verifies the probe operating point, where -10 VDC represents the typical target gap condition for Bently Nevada eddy-current systems. The 8 mm probe tip provides a 2.0 mm linear measurement range. Moreover, the ClickLoc coaxial connection maintains signal integrity between the probe and extension cable assembly while reducing connection-related signal disturbances. Frequently Asked Questions Q: What measurement signals can the 330103-05-15-10-02-00 provide?A: The probe provides dynamic vibration displacement signals, static shaft position signals, and phase reference signals when connected to compatible Bently Nevada monitoring hardware. Q: What target material is required for calibration performance?A: The standard calibration uses AISI 4140 steel targets. Other conductive materials may require system-specific calibration verification. Q: How should the probe gap voltage be checked during installation?A: The installation technician should verify the Proximitor output gap voltage and confirm the operating point near the standard -10 VDC target condition before machinery operation. Field Installation Guidelines Install the probe with the M10 x 1 threaded case securely mounted to the machine housing or bearing support structure. Maintain correct probe tip clearance from the conductive shaft surface according to the configured Proximitor calibration range. Route the coaxial cable away from high-current power conductors, variable frequency drive cables, and strong electromagnetic interference sources. Connect the cable shield according to the monitoring system grounding requirements to minimize electrical noise. Verify the probe output signal and gap voltage before commissioning the machinery monitoring channel. Confirm the probe installation position supports the intended measurement direction, including radial vibration, axial position, or Keyphasor applications.
$200.00 $100.00
-
Bently Nevada 330103-08-13-10-02-05 | Bently Nevada | 3300 XL 8 mm Proximity Probe
Bently Nevada 330103-08-13-10-02-05 3300 XL 8 mm Proximity Probe The Bently Nevada 330103-08-13-10-02-05, also cataloged as the 330103 3300 XL 8 mm Proximity Probe, operates as a dedicated eddy-current sensing component for shaft displacement and vibration measurement within the 3300 XL Proximity Transducer System. Hardware Specifications Parameter Specification Model 330103-08-13-10-02-05 Brand Bently Nevada Product Type 3300 XL 8 mm Proximity Probe Origin USA Weight 0.1 kg Dimensions Estimated shipping size: 20.4 x 22.2 x 3.7 cm Power Consumption Passive probe element; powered by compatible 3300 XL proximity system driver Probe Diameter 8 mm Thread Type M10 x 1 metric thread Probe Construction Without armor Minimum Unthreaded Length 80 mm Minimum Case Length 130 mm Total Length Option 1.0 meter (3.3 feet) Cable Type Miniature coaxial ClickLoc connector standard cable Agency Approvals CSA, ATEX, IECEx Tariff Code 8537101190 Shipment Location Xiamen, China Eddy-Current Measurement and Rotor Dynamics Monitoring The 330103-08-13-10-02-05 uses eddy-current sensing technology to measure the distance between the probe tip and a conductive rotating target. The probe converts shaft movement into electrical signals through the compatible 3300 XL driver and monitoring modules. Furthermore, the probe supports rotor dynamics analysis by providing displacement signals for vibration, radial position, and shaft motion evaluation. The system uses calibrated probe scaling characteristics to maintain measurement consistency across the operating gap range. The 3300 XL system validates probe operation through gap voltage monitoring. Standard installation practices use gap voltage targets near -10 VDC when establishing the correct operating position between the probe tip and the shaft surface. The miniature coaxial ClickLoc connector design provides a controlled signal path between the probe and extension cable assembly. In addition, the shielded cable structure helps reduce electrical interference and signal cross-talk during machinery monitoring. Frequently Asked Questions Q: What measurement principle does the Bently Nevada 330103-08-13-10-02-05 use?A: The probe uses eddy-current technology to detect changes in the distance between the probe tip and a conductive shaft surface. Q: Can the 330103-08-13-10-02-05 operate as a standalone sensor?A: No. The probe requires a compatible 3300 XL proximity system driver, extension cable, and monitoring electronics to process displacement signals. Q: What installation factor affects measurement accuracy?A: Proper probe gap adjustment, correct thread installation, shielded cable routing, and verification of gap voltage are required for accurate signal measurement. Field Installation Guidelines Install the probe with the M10 x 1 thread connection according to the mechanical mounting requirements of the machine housing. Maintain the specified minimum unthreaded length and case length during installation to avoid mechanical interference. Route the miniature coaxial cable away from high-current power conductors and strong electromagnetic interference sources. Connect cable shielding according to the 3300 XL system grounding requirements to minimize electrical noise. Verify the probe gap voltage after mechanical positioning before placing the monitoring channel into service. Confirm the probe, extension cable, and driver compatibility before commissioning the vibration monitoring loop.
$200.00 $100.00
-
Bently Nevada 330103-08-13-10-02-CN | Bently Nevada | 3300 XL 8 mm Proximity Probes
Bently Nevada 330103-08-13-10-02-CN 3300 XL 8 mm Proximity Probes The Bently Nevada 330103-08-13-10-02-CN, also cataloged as the 330103 3300 XL 8 mm Proximity Probe, operates as a dedicated hardware component for eddy-current displacement measurement and vibration monitoring within Bently Nevada TSI monitoring systems. Hardware Specifications Parameter Specification Model 330103-08-13-10-02-CN Brand Bently Nevada Product Type 3300 XL 8 mm Proximity Probe Origin USA Weight 0.323 kg Dimensions Overall case length: 130 mm; total cable length: 1.0 m Power Consumption Passive probe element; powered through compatible Proximitor sensor system Probe Diameter 8 mm Unthreaded Length 80 mm Cable Type Standard cable with miniature coaxial ClickLoc connector Connector Option 02: Miniature coaxial ClickLoc connector Agency Approval CN: Country-specific China approval option Probe Tip Material Polyphenylene sulfide (PPS) Probe Case Material AISI 303 or 304 stainless steel (SST) Pressure Sealing Viton O-ring between probe tip and case Measurement Principle Eddy-current non-contact displacement measurement Eddy-Current Probe Scaling and Rotor Dynamics Monitoring The 330103-08-13-10-02-CN uses eddy-current sensing technology to convert the distance between the probe tip and the rotating target into an electrical displacement signal. Therefore, the probe provides dynamic vibration and static position measurements for rotor monitoring applications. Bently Nevada proximity systems use calibrated probe scaling characteristics to maintain consistent displacement output. The probe operates as part of a matched proximity transducer chain with compatible Proximitor sensors, where gap voltage validation and signal conditioning support accurate shaft position analysis. For rotor dynamics evaluation, the probe measures shaft movement caused by vibration, axial displacement, and mechanical clearances. Additionally, correct probe installation and target surface conditions reduce measurement errors caused by mechanical runout or signal interference. Frequently Asked Questions Q: What measurement principle does the 330103-08-13-10-02-CN use?A: The probe uses eddy-current technology to measure the distance between the probe tip and the conductive target surface without physical contact. Q: Does the probe include an internal power supply circuit?A: No. The probe operates as a passive sensing element and requires connection to a compatible Bently Nevada Proximitor system for excitation and signal processing. Q: What sealing method does the probe use for differential pressure protection?A: The probe uses a Viton O-ring sealing structure between the probe tip and stainless steel case. The probe is not pressure tested before shipment. Field Installation Guidelines Install the probe with the sensing tip facing the measured shaft surface and maintain correct mechanical clearance according to the approved system setup. Connect the miniature coaxial ClickLoc connector securely to prevent signal interruption caused by loose mechanical connections. Route the probe cable separately from high-voltage power cables and strong electromagnetic interference sources. Maintain proper cable shielding and grounding practices through the connected monitoring system. Verify probe polarity, connector condition, and cable integrity before system commissioning. Confirm the probe gap voltage through the compatible Proximitor module and validate the operating range before vibration data collection. Ensure the target surface remains clean and free from contamination that may affect eddy-current measurement accuracy.
$200.00 $100.00
-
Bently Nevada 3300 XL 8 mm Proximity Probe | Bently Nevada | 330103-20-25-05-02-CN
Bently Nevada 330103-20-25-05-02-CN 3300 XL 8 mm Proximity Probe Configured for non-contact shaft displacement and vibration measurement in the Bently Nevada 3300 XL Proximity Transducer System, the Bently Nevada 330103-20-25-05-02-CN (330103 3300 XL 8 mm Proximity Probe) provides direct eddy-current signal conversion for rotor position and dynamic motion monitoring. Hardware Specifications Parameter Specification Model 330103-20-25-05-02-CN Brand Bently Nevada Product Type 3300 XL 8 mm Proximity Probe Origin USA Weight Approx. 0.12 kg Operating Temp -51 deg C to +177 deg C Power Consumption Passive probe device; power supplied by compatible 3300 XL Proximitor Sensor Probe Diameter 8 mm Thread Type M10 x 1 metric thread Probe Construction Unarmored stainless steel case with PPS probe tip Cable Type FEP insulated coaxial cable Connector Type Gold-plated miniature coaxial ClickLoc connector Measurement Principle Eddy-current displacement measurement System Linear Range 2.0 mm (80 mils) Scale Factor 7.87 V/mm (200 mV/mil) nominal with standard 3300 XL Proximitor Sensor and AISI 4140 target Linearity Within +/- 1% over full linear range Standard Compliance API 670 compliant mechanical and electrical configuration Eddy-Current Scaling and Rotor Dynamics Monitoring The 330103-20-25-05-02-CN uses an eddy-current sensing element to generate proportional voltage output according to the probe gap distance. The paired 3300 XL Proximitor Sensor processes the RF impedance change and converts the shaft displacement into a calibrated voltage signal. The probe provides a nominal scale factor of 200 mV/mil, which allows the monitoring system to evaluate shaft vibration amplitude, axial position changes, and Keyphasor reference conditions. Furthermore, proper gap voltage validation supports accurate probe operation, with typical Bently Nevada systems using approximately -10 VDC target gap conditions during calibration. The probe geometry supports rotor dynamics analysis by maintaining stable measurement response across rotating equipment operating conditions. The coaxial cable construction also reduces signal disturbance during vibration and displacement measurement. Frequently Asked Questions Q: What Proximitor Sensor is required for the 330103-20-25-05-02-CN probe?A: The probe operates with a compatible Bently Nevada 3300 XL Proximitor Sensor. The sensor provides excitation power and converts eddy-current changes into displacement voltage output. Q: Can the probe directly output a vibration signal without a Proximitor Sensor?A: No. The probe is a passive eddy-current sensing element. It requires a matching Proximitor Sensor to provide signal conditioning and output scaling. Q: What installation condition affects measurement accuracy?A: Probe mounting alignment, target material condition, cable routing, and correct gap voltage adjustment directly affect displacement measurement accuracy. Field Installation Guidelines Install the 330103-20-25-05-02-CN probe with the sensing tip aligned perpendicular to the rotating target surface. Maintain the specified M10 x 1 thread engagement and prevent mechanical contact between the probe tip and shaft surface. Route the coaxial cable away from high-current power conductors, switching devices, and electromagnetic interference sources. Connect the cable shield according to the Bently Nevada system grounding practice to reduce electrical noise. Before operation, verify the probe gap voltage through the connected 3300 XL Proximitor Sensor. Confirm that the output response matches the expected displacement scaling before placing the monitored machine into service. Avoid excessive bending or mechanical stress on the FEP insulated cable section. Protect all cable connections from moisture ingress and mechanical impact during installation.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330104-000-040-10-02-05 3300 XL 8 mm Proximity Probe
Bently Nevada 330104-000-040-10-02-05 3300 XL 8 mm Proximity Probe Configured for shaft displacement measurement in rotating equipment monitoring systems, the Bently Nevada 330104-000-040-10-02-05 (330104 3300 XL 8 mm Proximity Probe) provides direct eddy-current sensing for static and dynamic position measurement. Hardware Specifications Parameter Specification Model 330104-000-040-10-02-05 Brand Bently Nevada Product Type 3300 XL 8 mm Eddy Current Proximity Probe Origin USA Dimensions Total length: 1.0 m; Case length: 40 mm Operating Temp -51 deg C to +177 deg C Thread Type M10 x 1 metric thread Measurement Principle Eddy-current non-contact displacement measurement Linear Range 2.0 mm (80 mils) Scale Factor 7.87 V/mm (200 mV/mil) nominal Frequency Response 0 Hz to 10 kHz (+0, -3 dB) Probe Material AISI 303 or 304 stainless steel case; PPS tip Connector Type Miniature coaxial ClickLoc connector with terminal connector protector Cable Configuration 1.0 m unarmored cable Interchangeability Direct replacement without individual component matching Tensile Strength 330 N probe case to probe lead Hazardous Area Approval CSA, ATEX, IECEx multi-agency approval Eddy Current Measurement and Rotor Dynamics Features The 3300 XL 8 mm probe uses eddy-current technology to convert shaft position changes into electrical output signals. Therefore, the probe supports rotor dynamics analysis by providing displacement data for vibration and axial position monitoring. The probe system uses a nominal scale factor of 7.87 V/mm, which allows the connected monitoring system to calculate shaft movement from the generated voltage signal. In addition, gap voltage validation commonly uses a -10 VDC target condition to confirm correct probe installation and measurement range. The ClickLoc connector design maintains signal continuity between the probe and extension system. Furthermore, the probe construction supports cross-talk suppression practices through correct mechanical spacing and installation routing. Frequently Asked Questions Q: What measurement signals does the 330104-000-040-10-02-05 provide?A: The probe provides non-contact displacement signals for radial vibration, axial position, and phase reference measurement applications when connected to a compatible Bently Nevada monitoring system. Q: Does the probe require calibration after replacement?A: No individual matching calibration is required because the probe is designed for interchangeability within the specified 3300 XL 8 mm proximity system. Q: What installation factors affect measurement accuracy?A: Correct probe gap setting, target surface condition, cable routing, and shielding practices affect measurement performance. Field Installation Guidelines Install the probe with the M10 x 1 threaded body securely positioned against the mounting location. Verify probe gap voltage before operation and confirm the expected electrical range from the monitoring system. Route the coaxial cable away from high-current power conductors to reduce electrical interference. Maintain proper shielding and grounding practices according to the connected monitoring system installation requirements. Avoid mechanical stress on the probe cable and connector during installation. Confirm the target shaft surface condition before commissioning vibration or position measurements.
$200.00 $100.00
-
Bently Nevada 330104-00-02-10-02-00 | Bently Nevada | 3300 XL 8 mm Proximity Probes
Bently Nevada 330104-00-02-10-02-00 3300 XL 8 mm Proximity Probe The Bently Nevada 330104-00-02-10-02-00, also cataloged as the 330104 3300 XL 8 mm Proximity Probe, operates as a dedicated eddy-current measurement component for shaft displacement and vibration monitoring within Bently Nevada TSI monitoring systems. Hardware Specifications Parameter Specification Model 330104-00-02-10-02-00 Brand Bently Nevada Product Type 3300 XL 8 mm Proximity Probe, Metric Origin USA Weight 0.323 kg Dimensions 113 x 1.8 x 1.5 cm estimated shipping size Probe Diameter 8 mm Thread Type M10 x 1 metric thread Armor Type Flexible armor cable configuration Unthreaded Length 00 option, 0 mm Overall Case Length 02 option, 20 mm Total Length 10 option, 1.0 metre (39 in) Connector Type Miniature coaxial ClickLoc connector Cable Type Standard cable Agency Approval 00 option, not required Minimum Target Size 15.2 mm (0.6 in) diameter flat target Measurement Principle Eddy-current non-contact displacement measurement Eddy-Current Probe Scaling and Rotor Dynamics Monitoring The 330104-00-02-10-02-00 uses eddy-current sensing technology to convert shaft position changes into electrical displacement signals. Therefore, the probe provides direct measurement of radial vibration, axial position, and shaft motion when paired with compatible Bently Nevada proximity transducer systems. The probe supports rotor dynamics analysis by maintaining a consistent electromagnetic field between the probe tip and the conductive target surface. Furthermore, correct probe installation and gap adjustment allow the monitoring system to evaluate vibration amplitude and mechanical movement. The eddy-current signal chain requires proper gap voltage validation. Bently Nevada systems commonly verify probe operating conditions through gap voltage measurements, with -10 VDC targets representing a standard reference point for probe positioning and signal calibration. Frequently Asked Questions Q: What measurement principle does the 330104-00-02-10-02-00 use?A: The probe uses an eddy-current measurement principle to detect conductive target displacement without mechanical contact. Q: What connector configuration is included with this probe model?A: This model includes a miniature coaxial ClickLoc connector with standard cable construction. Q: Can this probe measure shaft vibration directly?A: The probe provides displacement signals. A compatible monitoring module processes these signals for vibration and position monitoring functions. Field Installation Guidelines Install the M10 x 1 threaded probe into the designated mounting location with correct mechanical alignment. Maintain proper probe-to-target spacing according to the configured monitoring system requirements. Route the coaxial cable away from high-current power conductors to reduce electromagnetic interference. Connect cable shielding according to the monitoring system grounding practice. Verify probe polarity, connector engagement, and signal continuity before commissioning. Perform gap voltage validation after installation to confirm the probe operates within the expected measurement range. Avoid excessive bending or mechanical stress on the armored cable during installation.
$200.00 $100.00
-
Bently Nevada 330104-00-03-10-02-00 | Bently Nevada | 3300 XL 8 mm Proximity Probe
Bently Nevada 330104-00-03-10-02-00 3300 XL 8 mm Reverse Mount Proximity Probe The Bently Nevada 330104-00-03-10-02-00, also cataloged as the 330104 3300 XL 8 mm Reverse Mount Proximity Probe, operates as a dedicated hardware component for eddy-current displacement measurement and rotor position monitoring within Bently Nevada TSI monitoring systems. Hardware Specifications Parameter Specification Model 330104-00-03-10-02-00 Brand Bently Nevada Product Type 3300 XL 8 mm Reverse Mount Proximity Probe Origin USA Dimensions 30 mm case length, 1.0 meter cable length, 8.0 mm tip diameter Operating Temp -52 deg C to +177 deg C Power Consumption Passive probe element, powered by compatible proximity transducer system Transducer Type Eddy Current Non-Contacting Proximity Transducer Measurement Range 2.0 mm linear range, operating range 0.25 mm to 2.25 mm Scale Factor 7.87 V/mm nominal, 200 mV/mil nominal Frequency Response 0 to 10 kHz, +0/-3 dB Thread Type M10 x 1 metric thread Unthreaded Length 0 mm Case Material AISI 303 or 304 stainless steel Tip Material Polyphenylene sulfide (PPS) Cable Insulation Fluoroethylene propylene (FEP) Connector Type Miniature coaxial ClickLoc connector, standard cable Pressure Capability Differential pressure sealing between probe tip and case, typically up to 3.4 bar / 50 psi Agency Approval Standard configuration, no approval option Eddy-Current Scaling and Rotor Dynamics Monitoring The 330104 series uses eddy-current sensing technology to convert shaft displacement into proportional electrical signals. The probe provides a nominal scale factor of 7.87 V/mm, allowing compatible Bently Nevada proximity systems to evaluate shaft position and vibration amplitude. Additionally, the probe output supports rotor dynamics analysis by providing continuous displacement information for vibration monitoring, axial position measurement, and mechanical clearance evaluation. The system requires correct gap voltage validation, where a typical operating target is approximately -10 VDC at the transducer output for proper measurement range alignment. The reverse mount construction provides pressure sealing between the probe tip and housing interface. Therefore, the installation configuration supports applications requiring isolation between the sensing surface and mounting environment. Frequently Asked Questions Q: What measurement principle does the 330104-00-03-10-02-00 use?A: The probe uses an eddy-current sensing principle to measure shaft displacement without mechanical contact between the probe tip and rotating target. Q: Does the probe require direct power input?A: No. The probe operates as part of a complete proximity transducer system and receives excitation from the compatible Bently Nevada signal conditioner. Q: What installation factors affect measurement accuracy?A: Proper thread engagement, probe gap setting, cable routing, shielding practice, and correct gap voltage validation affect signal quality and measurement accuracy. Field Installation Guidelines Install the M10 x 1 threaded probe body with correct mechanical alignment to maintain the specified sensing gap. Verify the probe tip faces the target shaft surface without physical contact during all operating conditions. Route the coaxial cable away from high-current power conductors to reduce electromagnetic interference. Connect cable shielding according to the monitoring system grounding requirements. Confirm the transducer output gap voltage before commissioning. A typical Bently Nevada setup uses approximately -10 VDC as the nominal target gap voltage. Avoid sharp cable bending near the ClickLoc connector to maintain cable integrity. Check mechanical mounting tightness and pressure sealing requirements before equipment startup.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330104-00-04-10-02-00 3300 XL 8 mm Proximity Probe
Bently Nevada 330104-00-04-10-02-00 3300 XL 8 mm Proximity Probe The Bently Nevada 330104-00-04-10-02-00, also cataloged as the 330104 3300 XL 8 mm Proximity Probe, operates as a dedicated eddy-current sensing component for shaft displacement and vibration measurement within Bently Nevada machinery monitoring systems. Hardware Specifications Parameter Specification Model 330104-00-04-10-02-00 Brand Bently Nevada Product Type 3300 XL 8 mm Proximity Probe Origin USA Weight 0.12 kg Dimensions 113 x 1.8 x 1.5 cm (shipping size) Power Consumption Supplied through compatible proximity transducer system Thread Type M10 x 1 thread Probe Diameter 8 mm Unthreaded Length Option 0 mm Overall Case Length Option 40 mm Total Length Option 1.0 meter (3.3 feet) Cable Type Miniature coaxial ClickLoc connector standard cable Armor Configuration Armored probe design Agency Approval Not required Tariff Code 8537101190 Shipment Location Xiamen, China Eddy-Current Measurement and Rotor Dynamics Features The 330104-00-04-10-02-00 uses an eddy-current sensing principle to measure shaft position changes without physical contact. Therefore, the probe provides displacement signals for machinery vibration monitoring, axial position measurement, and rotor dynamic analysis. The probe geometry follows the 3300 XL 8 mm series scaling characteristics. In addition, the system supports gap voltage validation through standard Bently Nevada proximity transducer calibration methods, including the commonly applied -10 VDC target gap reference during installation verification. The armored construction reduces mechanical damage risks in industrial routing environments. Furthermore, the miniature coaxial ClickLoc connector maintains signal continuity between the probe and extension cable assembly while supporting stable vibration monitoring circuits. Frequently Asked Questions (FAQ) Q: What measurement principle does the 330104-00-04-10-02-00 use?A: The probe uses an eddy-current measurement principle to detect shaft displacement by generating a proportional electrical output related to the distance between the probe tip and conductive target surface. Q: Does the probe require physical contact with the rotating shaft?A: No. The 330104-00-04-10-02-00 operates as a non-contact proximity sensing device and measures shaft motion through electromagnetic field changes. Q: What installation factor affects proximity probe signal accuracy?A: Probe gap adjustment, target material condition, cable routing, and proper grounding practices affect signal stability and measurement accuracy. Field Installation Guidelines Install the 330104-00-04-10-02-00 probe with the sensing tip aligned toward the monitored shaft surface. Maintain correct mechanical clearance according to the approved Bently Nevada installation procedure. Connect the miniature coaxial ClickLoc connector securely to prevent signal interruption caused by mechanical vibration. Route the probe cable away from high-current power conductors to reduce electromagnetic interference. Verify the probe gap voltage after installation using the compatible Bently Nevada proximity monitoring equipment. Confirm the output response before placing the machinery protection channel into service. Use proper shield termination and grounding practices to maintain measurement signal integrity. Avoid sharp cable bends and excessive mechanical stress on the armored section during installation.
$200.00 $100.00
-
Bently Nevada 330104-00-04-10-02-05 | Bently Nevada | 3300 XL 8 mm Proximity Probe
Bently Nevada 330104-00-04-10-02-05 3300 XL 8 mm Proximity Probe The Bently Nevada 330104-00-04-10-02-05, also cataloged as the 330104 3300 XL 8 mm Proximity Probe, operates as a dedicated eddy-current measurement component for shaft displacement and vibration monitoring within Bently Nevada TSI monitoring systems. Hardware Specifications Parameter Specification Model 330104-00-04-10-02-05 Brand Bently Nevada Product Series 3300 XL 8 mm Proximity Probes Product Type Eddy-Current Proximity Sensor Origin USA Weight 0.12 kg Dimensions Estimated shipping size: 113 x 1.8 x 1.5 cm Thread Type M10 x 1 metric thread Armor Type Armored probe design Overall Case Length 40 mm Minimum Unthreaded Length 0 mm Total Length 1.0 meter (3.3 feet) Connector Type Miniature coaxial ClickLoc connector Cable Type Standard cable Agency Approvals CSA, ATEX, IECEx Power Consumption Supplied through compatible proximity transducer system; value not specified Eddy-Current Probe Scaling and Rotor Dynamics Monitoring The 330104-00-04-10-02-05 uses eddy-current sensing technology to generate proportional displacement signals between the probe tip and conductive shaft surface. The probe output depends on target material characteristics, probe gap position, and oscillator excitation from the compatible proximity transducer system. The probe supports rotor dynamics monitoring applications by providing non-contact shaft position and vibration displacement measurement. Additionally, gap voltage validation procedures typically reference a -10 VDC target condition during calibration of Bently Nevada proximity systems. The armored construction protects the probe cable assembly in mechanical installation environments. Furthermore, the miniature coaxial ClickLoc connector provides a defined connection interface for field installation and maintenance operations. Frequently Asked Questions Q: What measurement principle does the Bently Nevada 330104-00-04-10-02-05 use?A: The probe uses eddy-current technology to measure shaft displacement without mechanical contact between the probe tip and the rotating target. Q: What connector configuration is included with this model?A: This model uses a miniature coaxial ClickLoc connector with standard cable configuration. Q: Does this probe require mechanical contact with the monitored shaft?A: No. The probe operates as a non-contact displacement sensor and requires correct installation gap adjustment for signal generation. Field Installation Guidelines Install the probe with the M10 x 1 thread interface according to the mechanical mounting requirements of the monitoring assembly. Maintain proper probe-to-target gap adjustment before system calibration. Route the armored cable away from high-current power conductors to reduce electrical interference. Ensure the connector interface remains clean and properly secured during installation. Connect the probe only to compatible Bently Nevada proximity transducer systems designed for 3300 XL 8 mm series probes. Verify signal polarity, cable continuity, and gap voltage response during commissioning procedures.
$200.00 $100.00
-
Bently Nevada 330104-00-04-10-02-CN | Bently Nevada | 3300 XL 8 mm Proximity Probe
Bently Nevada 330104-00-04-10-02-CN 3300 XL 8 mm Proximity Probe Configured for non-contact shaft displacement measurement in the 3300 XL Proximity Transducer System, the Bently Nevada 330104-00-04-10-02-CN (330104 3300 XL 8 mm Proximity Probe) provides direct physical signal detection through eddy-current sensing technology. Hardware Specifications Parameter Specification Model 330104-00-04-10-02-CN Brand Bently Nevada Product Type 3300 XL 8 mm Proximity Probe Origin USA Weight 0.12 kg Dimensions 123 x 1.8 x 1.5 cm Power Consumption Supplied through compatible Proximity Transducer System Probe Diameter 8 mm Thread Type M10 x 1 Probe Construction Armored probe design Unthreaded Length 0 mm Overall Case Length 40 mm Total Length 1.0 meter (3.3 feet) Connector Type Miniature coaxial ClickLoc connector Cable Type Standard cable Measurement Principle Eddy-current displacement sensing Agency Approvals CSA, ATEX, IECEx Eddy-Current Probe Scaling and Rotor Dynamics Monitoring The 330104-00-04-10-02-CN uses eddy-current probe scaling to convert shaft displacement into electrical output signals for machinery protection and condition monitoring applications. The probe detects changes in the electromagnetic field between the probe tip and the rotating target surface. Furthermore, the probe supports rotor dynamics analysis by providing displacement measurements required for vibration monitoring, shaft position evaluation, and mechanical behavior assessment. The armored construction protects the signal path in industrial installation environments while maintaining measurement consistency. The probe installation requires proper gap adjustment and signal verification. Bently Nevada proximity systems typically validate probe operation through gap voltage measurement, with -10 VDC used as a common target reference condition for correct probe positioning. Frequently Asked Questions Q: What measurement principle does the 330104-00-04-10-02-CN use?A: The probe uses eddy-current technology to measure shaft displacement without physical contact between the probe tip and the rotating target. Q: What connector configuration does this model provide?A: This model uses a miniature coaxial ClickLoc connector with standard cable configuration. Q: Can this probe operate independently without a Proximity Transducer System?A: No. The probe requires a compatible Bently Nevada Proximity Transducer System to provide excitation, signal conditioning, and displacement output processing. Field Installation Guidelines Install the probe with the specified M10 x 1 thread interface and confirm mechanical alignment before operation. Maintain correct probe-to-target spacing according to the applicable Bently Nevada installation procedure. Route the coaxial cable away from high-current power cables and sources of electromagnetic interference. Connect cable shielding according to the system grounding requirements to reduce electrical noise. Verify probe output voltage and gap condition before commissioning the monitoring channel. Avoid mechanical stress on the armored section and connector area during installation.
$200.00 $100.00
-
Bently Nevada 330104-00-05-50-11-00 | Bently Nevada | 3300 XL 8 mm Proximity Probe
Bently Nevada 330104-00-05-50-11-00 3300 XL 8 mm Proximity Probe The Bently Nevada 330104-00-05-50-11-00, also cataloged as the 330104 3300 XL 8 mm Proximity Probe, operates as a dedicated eddy-current displacement measurement component for shaft position and vibration monitoring within Bently Nevada TSI monitoring systems. Hardware Specifications Parameter Specification Model 330104-00-05-50-11-00 Brand Bently Nevada Product Series 3300 XL 8 mm Proximity Probe Product Type Eddy Current Proximity Sensor Origin USA Dimensions Probe case length: 50 mm; cable length: 5.0 m Operating Temp -51 deg C to +177 deg C Power Consumption Passive probe; powered by compatible 3300 XL Proximitor Sensor Target Material AISI 4140 Steel calibration target Probe Tip Diameter 8 mm Thread Size M10 x 1 Linear Range 2.0 mm (80 mils) Scale Factor 7.87 V/mm (200 mV/mil) Frequency Response 0 Hz to 10 kHz Case Material AISI 304 Stainless Steel Tip Material Polyphenylene Sulfide (PPS) Cable Type FluidLoc FEP insulated cable Connector Type Miniature coaxial ClickLoc connector with connector protector Agency Approval Standard configuration without agency approval Eddy-Current Scaling and Rotor Dynamics Measurement The 330104-00-05-50-11-00 uses an eddy-current sensing principle to convert shaft displacement into a proportional electrical output through a compatible 3300 XL Proximitor Sensor. The probe maintains a 7.87 V/mm scale factor across its 2.0 mm linear measurement range. Furthermore, the system evaluates rotor dynamics parameters by measuring radial vibration, shaft position, and mechanical movement. The probe gap voltage must be validated during installation, with the typical operating target centered around the -10 VDC range when connected to the Proximitor system. Proper gap adjustment ensures correct signal scaling and displacement measurement accuracy. The probe design incorporates TipLoc molding and CableLoc construction. In addition, the FluidLoc cable structure prevents oil and process fluid migration through the cable core, maintaining signal integrity in rotating equipment environments. Frequently Asked Questions Q: Can the 330104-00-05-50-11-00 probe operate without a Proximitor Sensor?A: No. The probe requires a compatible 3300 XL Proximitor Sensor to provide excitation and convert eddy-current impedance changes into a proportional voltage output. Q: What installation parameter must be checked before operation?A: The probe installation requires verification of mechanical gap and gap voltage. The final gap setting should match the Proximitor Sensor operating range, commonly validated near -10 VDC. Q: What cable feature prevents liquid migration?A: The FluidLoc cable design blocks oil and process fluid movement through the internal cable structure, reducing the risk of contamination at the connection point. Field Installation Guidelines Install the probe with the M10 x 1 threaded body fully secured against the mounting surface. Align the probe tip perpendicular to the conductive target surface to maintain correct eddy-current measurement geometry. Verify probe gap voltage after mechanical installation and before connecting the monitoring channel to operational machinery. Route the coaxial cable away from high-current power cables and strong electromagnetic interference sources. Maintain proper connector engagement when installing the miniature ClickLoc connector to prevent signal interruption caused by vibration. Connect cable shielding according to the monitoring system grounding practice to reduce electrical noise.
$200.00 $100.00
-
Bently Nevada 330104-00-06-10-01-05 | 3300 XL 8 mm Proximity Probe | Bently Nevada
Bently Nevada 330104-00-06-10-01-05 3300 XL 8 mm Proximity Probe The Bently Nevada 330104-00-06-10-01-05, also cataloged as the 330104 3300 XL 8 mm Proximity Probe, operates as a dedicated hardware component for eddy-current displacement measurement and vibration monitoring within the 3300 XL Proximity Transducer System. Hardware Specifications Parameter Specification Model 330104-00-06-10-01-05 Brand Bently Nevada Product Series 3300 XL 8 mm Proximity Probe Product Type Proximity Sensor Origin USA Weight 0.2 kg Dimensions Estimated shipping size: 32 x 30 x 2 cm Thread Type M10 x 1 thread Probe Diameter 8 mm Unthreaded Length 0 mm Overall Case Length 60 mm Cable Length 1.0 m (3.3 ft) Cable Type Standard cable with Miniature Coaxial ClickLoc Connector and connector protector Armor Option Armored probe construction Agency Approvals CSA, ATEX, IECEx Certifications Measurement Principle Eddy-current proximity measurement Signal Output Voltage output proportional to probe tip distance from conductive target Measurement Range Supports static position and dynamic vibration measurements Power Consumption Supplied through compatible 3300 XL Proximitor Sensor interface Eddy-Current Probe Scaling and Rotor Dynamics Monitoring The 330104-00-06-10-01-05 uses an eddy-current sensing principle to convert the physical gap between the probe tip and the conductive machine surface into an electrical voltage signal. The system maintains calibrated displacement measurement performance through matched probe, extension cable, and Proximitor sensor configurations. The 3300 XL 8 mm system supports rotor dynamics monitoring by measuring shaft displacement, radial vibration, axial position, and Keyphasor reference signals. Additionally, the probe design maintains signal stability during rotating machinery operation through controlled electromagnetic characteristics and defined mechanical geometry. The proximity system uses gap voltage validation with typical -10 VDC target conditions to verify probe operating position and measurement accuracy. Furthermore, the armored construction provides mechanical protection for installations exposed to cable routing stress or industrial environments. Frequently Asked Questions Q: What measurement signals can the 330104-00-06-10-01-05 provide?A: The probe provides displacement-related voltage signals that represent both static shaft position and dynamic vibration values when connected with a compatible 3300 XL Proximitor Sensor. Q: Can the probe cable and extension components be replaced with other 3300 XL components?A: Yes. The 3300 XL 8 mm system supports interchangeability between compatible probes, extension cables, and Proximitor sensors without individual bench calibration. Q: What connector configuration does this model use?A: This model uses a Miniature Coaxial ClickLoc Connector with connector protector and standard cable configuration. Field Installation Guidelines Install the M10 x 1 threaded probe into a suitable mounting location while maintaining correct mechanical alignment with the monitored shaft surface. Maintain proper probe tip clearance according to the 3300 XL system calibration requirements. Route the armored cable away from high-voltage power conductors and strong electromagnetic interference sources. Connect the cable shield and grounding path according to the monitoring system installation requirements. Verify the gap voltage after installation to confirm the probe operates within the specified measurement range. Avoid sharp cable bends near the ClickLoc connector area to prevent mechanical stress on the coaxial connection. Confirm compatibility between the probe, extension cable, and Proximitor Sensor before system commissioning.
$200.00 $100.00
-
Bently Nevada 330104-00-06-20-01-00 3300 XL 8 mm Proximity Probe | Bently Nevada
Bently Nevada 330104-00-06-20-01-00 3300 XL 8 mm Proximity Probe The Bently Nevada 330104-00-06-20-01-00, also cataloged as the 330104 3300 XL 8 mm Proximity Probe, operates as a dedicated hardware component for eddy-current displacement measurement within the 3300 XL Eddy Current Proximity Transducer System. The probe measures shaft vibration and position through non-contact gap sensing. Hardware Specifications Parameter Specification Model 330104-00-06-20-01-00 Brand Bently Nevada Product Type Proximity Sensors Series 3300 XL 8 mm Proximity Probe Origin USA Dimensions M10 x 1 threaded case, 60 mm case length, 2.0 m cable length Operating Temp -51 deg C to +177 deg C Power Consumption Supplied by compatible 3300 XL Proximitor sensor; probe has no independent power input Target Material AISI 4140 steel standard calibration target Measurement Principle Eddy-current non-contact displacement measurement Linear Range 2.0 mm (80 mils) Gap Range Approx. 0.25 mm to 2.25 mm (10 mils to 90 mils) System Sensitivity 7.87 V/mm (200 mV/mil) nominal Linearity Within +/- 5% of nominal scale factor Thread Type M10 x 1 metric thread Unthreaded Length 0 mm Cable Type Standard flexible coaxial cable, unarmored Connector Type Miniature coaxial ClickLoc connector with connector protector Case Material Stainless steel Tip Material Polyphenylene sulfide (PPS) Eddy-Current Measurement and Rotor Dynamics Characteristics The 3300 XL 8 mm proximity probe uses eddy-current scaling to convert shaft displacement into proportional electrical output signals. Therefore, the probe maintains a defined relationship between target gap distance and output voltage for vibration and position monitoring. The probe operates with a nominal sensitivity of 7.87 V/mm and supports dynamic shaft movement measurement through compatible Proximitor sensor modules. Additionally, technicians validate installation conditions through gap voltage checks, with standard systems using -10 VDC target gap references for correct probe positioning. The probe design incorporates TipLoc and CableLoc bonding technology to maintain mechanical connection strength between the sensing tip and cable assembly. Furthermore, the system structure reduces signal interference effects and supports accurate rotor dynamics analysis in rotating equipment monitoring applications. Frequently Asked Questions Q: Does the 330104-00-06-20-01-00 probe require individual calibration with the Proximitor sensor?A: No. The 3300 XL system supports probe, extension cable, and Proximitor sensor interchangeability without custom matching calibration. Q: What signal measurement method does this probe use?A: The probe uses an eddy-current measurement principle to detect shaft displacement by monitoring changes in the electrical field between the probe tip and target surface. Q: What installation condition affects measurement accuracy?A: Probe gap setting, target material condition, cable routing, and proper connector installation directly affect measurement accuracy. Field Installation Guidelines Install the probe with the M10 x 1 threaded section securely mounted according to the mechanical assembly requirements. Verify the probe tip-to-target gap before operation and confirm the expected gap voltage using the connected Proximitor sensor. Route the coaxial cable away from high-current conductors and strong electromagnetic interference sources. Avoid sharp cable bending near the ClickLoc connector to prevent mechanical stress on the cable termination. Maintain proper grounding practices for associated monitoring system components to reduce electrical noise. Confirm that the target surface material matches the specified AISI 4140 calibration condition before applying standard scaling values.
$200.00 $100.00
-
Bently Nevada 3300 XL 8 mm Proximity Probe 330104-00-06-50-01-00 Bently Nevada
Bently Nevada 330104-00-06-50-01-00 3300 XL 8 mm Proximity Probe The Bently Nevada 330104-00-06-50-01-00, also cataloged as the 330104 3300 XL 8 mm Proximity Probe, operates as a dedicated eddy-current measurement component for shaft displacement and vibration monitoring within Bently Nevada TSI monitoring systems. Hardware Specifications Parameter Specification Model 330104-00-06-50-01-00 Brand Bently Nevada Product Series 3300 XL 8 mm Proximity Probe Product Type Proximity Sensor Probe Tip Diameter 8.0 mm Thread Type M10 x 1 metric Probe Construction Armored probe with flexible stainless steel armor Unthreaded Length 0 mm Overall Case Length 60 mm Total Cable Length 5.0 m Connector Type Miniature coaxial ClickLoc connector with connector protector Cable Type Standard cable Probe Case Material 303 or 304 stainless steel Tip Material Polyphenylene Sulfide (PPS) Armor Material Flexible 302/304 stainless steel armor sleeve Linear Range 2.0 mm (80 mils) Linear Range Start Approximately 0.25 mm from probe tip Scale Factor 7.87 V/mm (200 mV/mil), +/- 6.5% typical Frequency Response 0 Hz to 10 kHz (+0, -3 dB) Target Material AISI 4140 steel Operating Temp -51 deg C to +177 deg C Relative Humidity 100% condensing, non-submerged with connector protection applied Origin USA Dimensions Probe case length: 60 mm; cable length: 5.0 m Power Consumption Supplied through compatible 3300 XL Proximitor Sensor; probe has no independent power input Eddy-Current Measurement and Rotor Dynamics Monitoring The 330104-00-06-50-01-00 uses an eddy-current sensing principle to detect shaft surface movement without mechanical contact. Therefore, the probe measures both static shaft position and dynamic vibration signals through changes in the electromagnetic field between the probe tip and the target surface. The 3300 XL 8 mm probe system uses calibrated probe scaling with a nominal scale factor of 7.87 V/mm. In addition, the system supports gap voltage validation through the Proximitor Sensor output, where a typical -10 VDC target indicates the probe operates near the electrical center of its measurement range. Furthermore, the probe supports rotor dynamics analysis by providing displacement signals required for shaft vibration, axial position, and mechanical condition monitoring. The armored construction reduces mechanical damage risks in installations with restricted routing conditions while maintaining signal transmission performance. Frequently Asked Questions Q: What type of signal does the 330104-00-06-50-01-00 generate?A: The probe generates an eddy-current displacement signal that requires connection to a compatible 3300 XL Proximitor Sensor for signal conditioning and output processing. Q: Can the probe operate without a Proximitor Sensor?A: No. The probe functions as a passive sensing element and requires a compatible driver module to provide excitation and convert the eddy-current measurement into monitoring signals. Q: What installation factors affect measurement accuracy?A: Target material condition, probe gap setting, cable routing, connector protection, and proper mechanical mounting influence measurement stability and calibration performance. Field Installation Guidelines Install the probe with the specified M10 x 1 metric threaded mounting interface and maintain proper mechanical alignment with the shaft target surface. Verify the probe gap voltage after connection to the compatible Proximitor Sensor. Confirm the electrical output remains within the configured monitoring range. Route the armored cable away from high-current conductors, ignition sources, and strong electromagnetic interference fields. Maintain proper connector protection to prevent moisture ingress in condensing environments. Connect cable shielding according to the system grounding practice defined for the Bently Nevada monitoring rack. Inspect the probe tip and target surface condition before commissioning to prevent measurement errors caused by surface damage or contamination.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330104-00-07-10-02-00 3300 XL 8 mm Proximity Probe
Bently Nevada 330104-00-07-10-02-00 3300 XL 8 mm Proximity Probe The Bently Nevada 330104-00-07-10-02-00, also cataloged as the 330104 3300 XL 8 mm Proximity Probe, operates as a dedicated hardware component for non-contact shaft displacement measurement and vibration monitoring within Bently Nevada 3300 XL proximity transducer systems. Hardware Specifications Parameter Specification Model 330104-00-07-10-02-00 Brand Bently Nevada Product Series 3300 XL 8 mm Proximity Probes Probe Type Eddy-current proximity probe Thread Type M10 x 1 thread Armor Option Armored probe construction Unthreaded Length 0 mm Overall Case Length 70 mm Total Length 1.0 meter (3.3 feet) Connector Type Miniature coaxial ClickLoc connector Cable Type Standard cable Agency Approval Not required Origin USA Weight 0.14 kg Dimensions 30 x 30 x 5 cm (estimated shipping size) Power Consumption Passive probe element; requires compatible proximity system driver module Eddy-Current Measurement and Gap Voltage Characteristics The 330104-00-07-10-02-00 uses an eddy-current sensing principle to measure shaft position without mechanical contact. The probe generates an electromagnetic field between the probe tip and the rotating target surface, and the connected driver converts impedance changes into proportional displacement signals. Additionally, the probe configuration supports gap voltage validation through the associated proximity driver. Bently Nevada systems typically verify probe operating range using gap voltage targets around -10 VDC during field calibration procedures. This measurement confirms correct probe-to-target spacing and maintains accurate rotor dynamics monitoring. The armored construction reduces mechanical damage risks during installation, while the miniature coaxial ClickLoc connector provides a controlled connection path for vibration monitoring signal transmission. Furthermore, the standard cable configuration supports integration with compatible 3300 XL proximity transducer components. Frequently Asked Questions Q: What measurement principle does the 330104-00-07-10-02-00 use?A: The probe uses an eddy-current sensing method to measure shaft displacement by detecting changes in the electromagnetic field between the probe tip and conductive target. Q: What connector configuration does this probe provide?A: This model uses a miniature coaxial ClickLoc connector with standard cable configuration for connection to compatible Bently Nevada proximity systems. Q: Does this model include agency approvals?A: No. The 330104-00-07-10-02-00 configuration does not include additional agency approval options. Field Installation Guidelines Install the probe with the specified M10 x 1 thread connection and maintain correct mechanical alignment with the monitored shaft surface. Ensure the probe tip remains free from contamination, physical impact, and excessive mechanical stress during installation. Route the coaxial cable separately from high-voltage power conductors to reduce electromagnetic interference. Verify the probe gap setting through the connected proximity driver before commissioning. Use the system gap voltage measurement to confirm proper signal operation and stable rotor position monitoring. Maintain proper cable routing and connector engagement to prevent intermittent signal conditions during continuous machine operation.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330104-00-07-50-02-00 3300 XL 8 mm Proximity Probe
Bently Nevada 330104-00-07-50-02-00 3300 XL 8 mm Proximity Probe Configured for non-contact shaft displacement measurement in the Bently Nevada 3300 XL 8 mm Proximity Transducer System, the Bently Nevada 330104-00-07-50-02-00 (330104 3300 XL 8 mm Proximity Probe) provides direct eddy-current sensing output through an armored probe assembly with a 5.0 meter cable and miniature coaxial ClickLoc connector. Hardware Specifications Parameter Specification Model 330104-00-07-50-02-00 Brand Bently Nevada Product Type 3300 XL 8 mm Proximity Probe Origin USA Weight 0.3 kg Dimensions 20.5 x 22.4 x 3.3 cm estimated shipping size Thread Type M10 x 1 Probe Construction Armored probe design Unthreaded Length 0 mm Overall Case Length 70 mm Total Length 5.0 meters (16.4 feet) Cable Type Miniature coaxial ClickLoc connector standard cable Agency Approval Not required Measurement Principle Eddy-current displacement sensing Eddy-Current Probe Scaling and Rotor Dynamics Monitoring The 3300 XL 8 mm Proximity Probe uses eddy-current measurement technology to detect shaft displacement without mechanical contact. The probe generates a proportional electrical output according to the target surface distance, allowing the monitoring system to process radial vibration and axial position signals. The 330104 series supports TSI applications where rotor dynamics analysis requires stable displacement feedback. Therefore, proper probe gap setting and gap voltage validation remain necessary during commissioning. Bently Nevada proximity systems typically use a negative gap voltage target near -10 VDC for normal operating range verification. The armored construction protects the probe cable against mechanical stress during field installation. Additionally, the miniature coaxial ClickLoc connector maintains signal continuity between the probe and extension system. Frequently Asked Questions Q: What measurement method does the 330104-00-07-50-02-00 use?A: The probe uses eddy-current sensing technology to measure shaft displacement by detecting changes in the electromagnetic field between the probe tip and the conductive target. Q: Does the 330104-00-07-50-02-00 require a specific gap voltage adjustment?A: Yes. Field commissioning normally verifies probe gap voltage to confirm the operating position within the transducer system range. Bently Nevada systems commonly reference approximately -10 VDC as a typical target value. Q: What connector configuration does this model include?A: This model uses a miniature coaxial ClickLoc connector with standard cable construction and a total cable length of 5.0 meters. Field Installation Guidelines Install the M10 x 1 threaded probe into the designated mounting location while maintaining correct mechanical alignment with the shaft target. Verify the probe tip clearance before operation to prevent physical contact with rotating components. Confirm the gap voltage output after installation to validate correct probe positioning. Route the armored cable away from high-current power conductors to reduce electrical interference. Maintain proper cable bending radius and avoid excessive mechanical force on the ClickLoc connector. Connect cable shielding according to the monitoring system grounding requirements. Verify signal stability during initial rotor rotation and vibration monitoring checks.
$200.00 $100.00
-
Bently Nevada 330104-00-08-05-02-00 | Bently Nevada | 3300 XL 8 mm Proximity Probe
Bently Nevada 330104-00-08-05-02-00 3300 XL 8 mm Proximity Probe The Bently Nevada 330104-00-08-05-02-00, also cataloged as the 330104 3300 XL 8 mm Proximity Probe, operates as a dedicated hardware component for non-contact shaft displacement measurement within Bently Nevada TSI monitoring systems. Hardware Specifications Parameter Specification Model 330104-00-08-05-02-00 Brand Bently Nevada Product Series 3300 XL 8 mm Proximity Probe Origin USA Weight 0.3 kg Dimensions Estimated shipping size: 1.8 x 1.6 x 121 cm Power Consumption Passive probe element, powered by compatible Proximity Transducer System Probe Type Eddy-current proximity probe Thread Type M10 x 1 thread Armor Option Armored probe construction Minimum Unthreaded Length 0 mm Overall Case Length 80 mm Total Length 0.5 meter (1.6 feet) Connector Type Miniature coaxial ClickLoc connector Cable Type Standard cable Agency Approval Not required Eddy-Current Measurement and Rotor Dynamics Monitoring The Bently Nevada 330104 series uses eddy-current probe scaling to convert shaft displacement changes into proportional electrical signals. The probe operates with compatible Bently Nevada proximity systems to monitor radial vibration, shaft position, and rotor dynamic behavior. The probe design supports gap voltage validation procedures, where field technicians verify probe installation conditions against standard operating targets, including -10 VDC gap voltage references. Additionally, the miniature coaxial ClickLoc connector maintains signal connection integrity while reducing installation complexity in machinery monitoring assemblies. The armored construction protects the probe cable section against mechanical stress during routing and installation. Therefore, correct probe orientation, target surface clearance, and cable separation from high-noise sources help maintain accurate vibration measurement signals. Frequently Asked Questions Q: What measurement technology does the Bently Nevada 330104-00-08-05-02-00 use?A: The probe uses eddy-current sensing technology to measure shaft displacement without physical contact with the rotating target. Q: What connector configuration is included with this model?A: This model includes a miniature coaxial ClickLoc connector with a standard cable configuration. Q: Does the probe require agency approval certification?A: The specified 330104-00-08-05-02-00 configuration does not include agency approval requirements. Field Installation Guidelines Install the M10 x 1 threaded probe into the designated mounting location with proper mechanical alignment. Maintain correct probe tip orientation toward the monitored shaft surface to ensure accurate displacement measurement. Verify probe gap voltage after installation using compatible Bently Nevada monitoring equipment. Route the miniature coaxial cable away from high-voltage power conductors and strong electromagnetic interference sources. Connect the ClickLoc connector securely and confirm mechanical locking before system operation. Check cable armor condition during installation to prevent damage from vibration, abrasion, or contact with moving components.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330104 3300 XL 8 mm Proximity Probe
Bently Nevada 330104 3300 XL 8 mm Proximity Probe The Bently Nevada 330104-00-08-10-01-05, also cataloged as the 330104 3300 XL 8 mm Proximity Probe, performs non-contact shaft displacement measurement using eddy-current technology within Bently Nevada proximity transducer systems. The probe features an M10 x 1 thread, armored construction, a 1.0 meter cable, and CSA, ATEX, IECEx approvals. Hardware Specifications Parameter Specification Model 330104-00-08-10-01-05 Brand Bently Nevada Product Series 3300 XL 8 mm Proximity Probe Product Type Proximity Sensor Origin USA Thread Type M10 x 1 Construction Armored probe design Cable Length 1.0 meter (3.3 feet) Connector Type Miniature coaxial ClickLoc connector with connector protector Minimum Unthreaded Length 0 mm Minimum Case Length 80 mm Approvals CSA, ATEX, IECEx Measurement Technology Eddy-current proximity sensing System Compatibility 3300 XL 8 mm proximity transducer system Power Consumption Supplied by compatible Proximitor sensor; no direct probe power input Eddy-Current Measurement and Rotor Dynamics The Bently Nevada 330104-00-08-10-01-05 uses eddy-current probe scaling to convert shaft displacement changes into proportional electrical signals through the compatible Proximitor sensor. The system maintains consistent probe characteristics across interchangeable probes, extension cables, and sensors. Additionally, the probe supports rotor dynamics monitoring by providing non-contact vibration and position measurements. The eddy-current sensing principle allows measurement without mechanical contact between the probe tip and rotating components. The 3300 XL 8 mm system follows API 670 mechanical configuration requirements for linear range, accuracy, and temperature stability. Furthermore, the ClickLoc connector design provides a controlled connection interface for industrial vibration monitoring installations. Frequently Asked Questions Q: Does the 330104-00-08-10-01-05 probe require individual calibration with extension cables?A: No. The 3300 XL 8 mm system supports interchangeability between compatible probes, extension cables, and Proximitor sensors without individual bench calibration. Q: What type of signal does the probe generate?A: The probe operates as an eddy-current sensing element and requires a compatible Proximitor sensor to convert displacement measurements into monitoring signals. Q: What approvals are available for this probe configuration?A: This configuration includes CSA, ATEX, and IECEx approvals for installation requirements defined by the selected hazardous area classification. Field Installation Guidelines Install the probe with the specified M10 x 1 mounting thread and maintain correct mechanical alignment with the target shaft surface. Verify probe gap voltage during commissioning using the compatible Proximitor sensor. Bently Nevada systems commonly use approximately -10 VDC gap voltage targets for proper probe operation. Route probe cables separately from high-current power wiring to reduce electrical interference. Maintain proper shielding and grounding practices according to the monitoring system installation requirements. Confirm connector engagement before operation and protect the miniature coaxial ClickLoc connector from mechanical stress. Check probe tip clearance and mounting rigidity to prevent measurement errors caused by mechanical movement.
$200.00 $100.00
-
Bently Nevada 330104-00-08-50-02-00 Bently Nevada 3300 XL Proximity Probe
Bently Nevada 330104-00-08-50-02-00 3300 XL 8 mm Eddy Current Proximity Probe The Bently Nevada 330104-00-08-50-02-00, also cataloged as the 330104 3300 XL 8 mm Eddy Current Proximity Probe, operates as a dedicated hardware component for shaft displacement and vibration measurement within the 3300 XL Proximity Transducer System. Suffix Breakdown & Model Matrix Option Code Specification Base Model 330104 - 3300 XL 8 mm Eddy Current Proximity Probe Thread Configuration M10 x 1 metric threaded case Unthreaded Length 00 - 0 mm unthreaded case section Case Length 08 - 80 mm overall case length Total Length 50 - 5.0 meters system length Connector Option 02 - Miniature coaxial ClickLoc connector with standard cable Agency Approval 00 - No agency approval option Hardware Specifications Parameter Specification Model 330104-00-08-50-02-00 Brand Bently Nevada Product Type 3300 XL 8 mm Eddy Current Proximity Probe Origin USA Weight 0.2kg Dimensions 80 mm case length, 8 mm probe tip diameter Operating Temp -35 deg C to +177 deg C Power Consumption Powered by compatible 3300 XL Proximity Transducer System driver Measurement Principle Eddy current non-contact displacement measurement Linear Range 2.0 mm (80 mils) Scale Factor 7.87 V/mm (200 mV/mil) nominal Target Material AISI 4140 steel calibration target Linear Range Start Approximately 0.25 mm (10 mils) from target Linear Range End Approximately 2.3 mm (90 mils) from target Probe Tip Diameter 8 mm Thread Size M10 x 1 metric System Cable Length 5.0 meters Connector Type Gold-plated miniature coaxial ClickLoc connector Cable Protection Standard unarmored cable Cable Pull Strength Up to 330 N (75 lbf) using CableLoc design Humidity Limit 100% condensing, non-submersible Interchangeability Compatible with other 3300 XL 8 mm system components without recalibration Eddy Current Measurement and Rotor Dynamics Characteristics The 330104-00-08-50-02-00 probe uses eddy-current sensing technology to convert shaft displacement into electrical signals. Therefore, the connected Proximity Transducer System can process radial vibration, axial position, and mechanical gap measurements. The probe maintains a nominal 7.87 V/mm scale factor across the calibrated measurement range. In addition, the system requires correct gap voltage validation, where a typical -10 VDC target condition confirms proper probe positioning and driver operation. The 3300 XL 8 mm architecture supports rotor dynamics monitoring by providing stable displacement feedback for rotating machinery analysis. Furthermore, the miniature coaxial ClickLoc connection reduces installation variation and maintains signal integrity between the probe and extension cable. Frequently Asked Questions Q: What measurement principle does the Bently Nevada 330104-00-08-50-02-00 use?A: The probe uses eddy-current technology to measure shaft displacement without physical contact with the rotating target. Q: Does the probe require recalibration when replacing another 3300 XL 8 mm probe?A: The probe is designed for interchangeability within the 3300 XL 8 mm system and does not require recalibration when compatible system components are used. Q: What cable and connector configuration does this model include?A: The model includes a 5.0 meter standard cable with a miniature coaxial ClickLoc connector and unarmored cable construction. Field Installation Guidelines Install the probe with the M10 x 1 threaded section securely mounted in the machine housing while maintaining the specified sensing gap between the probe tip and shaft target. Route the coaxial cable away from high-current power conductors, variable frequency drive output cables, and strong electromagnetic interference sources. Maintain proper cable support to prevent mechanical stress at the probe connector. Connect the probe to the compatible 3300 XL Proximity Transducer System driver. Verify the gap voltage output before operation and confirm the expected -10 VDC target condition during calibration checks. Ensure the probe tip remains free from contamination, mechanical impact, and conductive debris that may affect eddy-current measurement accuracy.
$200.00 $100.00
Anda telah melihat 72 dari 693 produk