Honeywell FC-PDB-ARTF05 Safety Manager A.R.T Fused Power Distribution Board The Honeywell FC-PDB-ARTF05, also cataloged as the PDB-ARTF05 Fused Power Distribution...
Baca selengkapnya
Dukungan Pengembalian Dana, Layanan 7X24jam, Hubungi kami .
Hubungi kami: +86 135 995 07613
Tersedia pada hari kerja antara pukul 09.00 hingga 18.00
Email kami: sales2@industriaxplc.com
Tersedia 24/7 untuk pertanyaan dan dukungan
Keterangan
Honeywell FC-PDB-ARTF05 Safety Manager A.R.T Fused Power Distribution Board
The Honeywell FC-PDB-ARTF05, also cataloged as the PDB-ARTF05 Fused Power Distribution Board, provides fused 5 VDC and 24 VDC power distribution with watchdog signal transfer within Honeywell Safety Manager A.R.T. platforms.
Hardware Specifications
Parameter
Specification
Model
FC-PDB-ARTF05
Brand
Honeywell
Product Type
Safety Manager A.R.T. Fused Power Distribution Board
Origin
USA
Weight
0.4 kg
Dimensions
23.5 x 10.8 x 6.8 cm
Operating Temp
-20 to +70 deg C (T4); -20 to +55 deg C (T5), no derating
Storage Temp
-40 to +85 deg C
Humidity
5 to 95 % RH, non-condensing
Power Supply Input
5 VDC +/-5 % and 24 VDC +/-20 %
Power Dissipation
8 W typical
Hold-up Time
>= 10 ms
Isolation
1.5 kV RMS
Digital Inputs
16 x 24 VDC
Digital Outputs
8 x 24 VDC
Fuse Protection
Individual fuse protection per output channel
Functional Safety Rating
SIL 3 functional safety compliance
Environmental Protection
IP66 protection design
Tariff Code
8537101190
Channel Isolation and Safety Power Distribution
The FC-PDB-ARTF05 distributes fused controller cabinet power and watchdog signals to connected I/O cabinets. Each output channel uses individual fuse protection to isolate field-side faults and prevent power interruption across unaffected channels.
Furthermore, the module uses an A.R.T. dual-channel design to support fault-tolerant power distribution functions. The board transfers incoming 5 VDC power from CPx through fuse Fx.y to watchdog connector WdPx.y, maintaining controlled power routing inside the Safety Manager architecture.
For Honeywell safety systems, the module supports channel-to-channel isolation concepts used in process control installations. The isolated distribution paths reduce electrical interference between independent I/O circuits and maintain stable signal reference conditions.
Frequently Asked Questions
Q: What voltage levels does the FC-PDB-ARTF05 distribute? A: The module distributes fused 5 VDC +/-5 % controller power and 24 VDC +/-20 % field-side power circuits.
Q: Does the FC-PDB-ARTF05 provide individual channel protection? A: Yes. Each output channel includes individual fuse protection to limit fault propagation between connected circuits.
Q: What safety architecture is supported by the FC-PDB-ARTF05? A: The module supports Honeywell Safety Manager A.R.T. architecture with SIL 3 functional safety requirements.
Field Installation Guidelines
Install the FC-PDB-ARTF05 inside a suitable control cabinet with protection against conductive contamination and excessive vibration.
Verify 5 VDC and 24 VDC supply polarity before connecting field wiring.
Separate power wiring from low-level signal wiring to reduce electromagnetic interference.
Connect cabinet grounding according to the Safety Manager system grounding design.
Inspect fuse status indicators and wiring terminals during commissioning and preventive maintenance.
Confirm watchdog signal routing between controller cabinets and I/O cabinets before system operation.
Maintain environmental conditions within the specified temperature and humidity limits.
