Yokogawa NFCP501-W05 S1 CPU Module Configured for real-time control program execution in FCN-500 controller network processing, the Yokogawa NFCP501-W05 S1...
Baca selengkapnya
Dukungan Pengembalian Dana, Layanan 7X24jam, Hubungi kami .
Hubungi kami: +86 135 995 07613
Tersedia pada hari kerja antara pukul 09.00 hingga 18.00
Email kami: sales2@industriaxplc.com
Tersedia 24/7 untuk pertanyaan dan dukungan
Keterangan
Yokogawa NFCP501-W05 S1 CPU Module
Configured for real-time control program execution in FCN-500 controller network processing, the Yokogawa NFCP501-W05 S1 (NFCP501) CPU module provides direct physical/electrical execution within STARDOM FCN-500 platforms.
The unit operates as the central execution core for sequence logic, task scheduling, and network communication handling in a distributed controller architecture. Processing is performed through an embedded Intel Atom E3815 CPU with ECC-protected memory subsystems and dual Ethernet interfaces for deterministic controller-to-controller and controller-to-I/O data exchange.
Suffix Breakdown & Model Matrix
NFCP501: Base CPU module series for FCN-500 platform
W: Extended function variant for expanded software and application compatibility
0: Standard performance grade configuration
5: Non-explosion-protected hardware variant
S1: Hardware revision level (Style 1)
Hardware Specifications
Parameter
Specification
ModelBrand
Yokogawa NFCP501-W05 S1
Origin
Japan (Yokogawa Electric Corporation)
Weight
Approx. 0.3 kg
Dimensions
2.2 cm x 12.4 cm x 12.6 cm
OperatingTemp
0 degC to 55 degC
PowerConsumption
Not specified in source data
Processor
Intel Atom E3815, 1.46 GHz
Main Memory
256 MB ECC RAM
Flash Memory
1 GB on-board
NVRAM
2 MB ECC, battery-backed
Network Interface
2 x Ethernet 10/100/1000BASE-T
Serial Interface
1 x RS-232-C (0.3 to 115.2 kbps)
Storage
SDHC slot, 4 GB to 32 GB support
Task Capacity
Up to 16 tasks, 16 priority levels
Execution Cycle
Minimum 5 ms task cycle
Process Control Communication Integrity Layer
The NFCP501-W05 S1 implements dual-channel Ethernet routing with deterministic frame handling for controller synchronization within STARDOM FCN-500 architectures. In Yokogawa process control environments, embedded communication stacks support structured data exchange across supervisory and field-level nodes using redundant network paths. Channel-to-channel isolation logic is applied at board level to minimize cross-interference between CPU execution bus and external network interfaces. ECC-protected memory arrays maintain instruction integrity under transient electrical disturbance conditions.
Frequently Asked Questions
Q: Can the NFCP501-W05 S1 operate in redundant CPU configuration? A: Yes. The module supports duplex CPU configuration with automatic failover. In redundant mode, internal synchronization ensures state transfer consistency between primary and standby modules.
Q: Does the RS-232-C interface remain available in redundant mode? A: No. The serial interface is disabled when the module is configured in duplex redundant architecture.
Q: What is the effect of ECC memory on runtime execution? A: ECC memory corrects single-bit errors in real time, preventing instruction corruption during task execution cycles without halting CPU operation.
Field Installation Guidelines
Install the module in an FCN-500 compatible rack slot with direct backplane engagement. Ensure power is fully isolated before insertion or removal. Ethernet cabling must maintain standard twisted-pair shielding with proper grounding at cabinet entry point. Avoid routing RS-232-C lines parallel to high-voltage or inverter-driven motor cables to reduce electromagnetic coupling. In redundant configurations, verify identical firmware revisions across CPU pairs before synchronization initialization.
