Sensor dan probe menyediakan pemantauan yang akurat untuk peralatan industri. Produk kami mencakup probe getaran, jarak, dan perpindahan dari produsen terkemuka. Kami menyediakan model yang masih ada maupun yang sudah dihentikan produksinya dengan dukungan global yang tepercaya.
Sensor dan Probe
-
Bently Nevada 330905-00-25-05-02-05 Bently Nevada 3300 NSv Proximity Probe
Bently Nevada 330905-00-25-05-12-CN 3300 NSv Proximity Probe The Bently Nevada 330905-00-25-05-12-CN, also cataloged as the 330905 3300 NSv Proximity Probe, operates as a dedicated hardware component for shaft displacement measurement within Bently Nevada 3300 XL NSv Transducer System platforms. Hardware Specifications Parameter Specification Model 330905-00-25-05-12-CN Brand Bently Nevada Product Type 3300 NSv Proximity Probe Origin USA Weight 0.05 kg Dimensions 1.8 x 1.6 x 66 cm estimated shipping size Power Consumption Supplied through compatible Proximitor Sensor, not specified Thread Type M10 x 1 metric thread Armor Configuration Without armor Unthreaded Length 0 mm Overall Case Length 250 mm Total Length 0.5 meter (20 in) Connector Type Miniature coaxial ClickLoc connector Cable Type FluidLoc cable Agency Approval Multiple Approval Average Scale Factor 7.87 V/mm (200 mV/mil) Measurement Principle Eddy-current displacement sensing Eddy-Current Probe Scaling and Rotor Dynamics The 330905-00-25-05-12-CN uses an eddy-current measurement principle to convert shaft position changes into electrical displacement signals. Therefore, the probe provides a 7.87 V/mm (200 mV/mil) average scale factor for compatibility with the 3300 XL NSv Proximitor Sensor. The compact M10 x 1 mechanical design supports installation where standard 3300 and 3300 XL 5 mm or 8 mm transducer systems cannot be installed. In addition, the probe geometry supports rotor dynamics monitoring applications by measuring radial vibration, axial position, and shaft movement characteristics. The system configuration requires proper gap voltage validation during commissioning. Furthermore, Bently Nevada monitoring systems typically verify probe operating range through gap voltage measurements, including -10 VDC target reference conditions for correct eddy-current probe operation. Frequently Asked Questions Q: What monitoring system is compatible with the 330905-00-25-05-12-CN probe?A: The probe operates as part of the 3300 XL NSv Transducer System and requires a compatible 3300 XL NSv Proximitor Sensor and extension cable configuration. Q: Can this probe replace older 3300 RAM or 3000-series systems directly?A: The 3300 XL NSv system can replace 3300 RAM and 3000-series or 7000-series 190 Transducer Systems. However, upgrades may require replacement of the probe, extension cable, and Proximitor Sensor depending on the original system configuration. Q: Does the probe include armor protection?A: No. The 330905-00-25-05-12-CN uses a non-armored construction with a FluidLoc cable and miniature coaxial ClickLoc connector. Field Installation Guidelines Install the 330905-00-25-05-12-CN probe with the specified M10 x 1 thread engagement and maintain correct mechanical alignment with the rotating target surface. Route the probe cable away from high-current power conductors and electromagnetic interference sources. Use proper cable support to prevent mechanical stress at the connector interface. Connect the cable shield according to the monitoring system grounding practice. Avoid grounding methods that create additional ground loops between the probe system and machinery monitoring equipment. During commissioning, verify probe clearance, gap voltage, and signal response through the connected Proximitor Sensor. Confirm that the measured displacement signal remains within the expected operating range before enabling machine protection functions.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330905-00-25-05-12-CN 3300 NSv Proximity Probe
Bently Nevada 330905-00-25-05-12-CN 3300 NSv Proximity Probe The Bently Nevada 330905-00-25-05-12-CN, also cataloged as the 330905 3300 NSv Proximity Probe, operates as a dedicated hardware component for shaft displacement measurement within Bently Nevada 3300 XL NSv Transducer System platforms. Hardware Specifications Parameter Specification Model 330905-00-25-05-12-CN Brand Bently Nevada Product Type 3300 NSv Proximity Probe Origin USA Weight 0.05 kg Dimensions 1.8 x 1.6 x 66 cm estimated shipping size Power Consumption Supplied through compatible Proximitor Sensor, not specified Thread Type M10 x 1 metric thread Armor Configuration Without armor Unthreaded Length 0 mm Overall Case Length 250 mm Total Length 0.5 meter (20 in) Connector Type Miniature coaxial ClickLoc connector Cable Type FluidLoc cable Agency Approval Multiple Approval Average Scale Factor 7.87 V/mm (200 mV/mil) Measurement Principle Eddy-current displacement sensing Eddy-Current Probe Scaling and Rotor Dynamics The 330905-00-25-05-12-CN uses an eddy-current measurement principle to convert shaft position changes into electrical displacement signals. Therefore, the probe provides a 7.87 V/mm (200 mV/mil) average scale factor for compatibility with the 3300 XL NSv Proximitor Sensor. The compact M10 x 1 mechanical design supports installation where standard 3300 and 3300 XL 5 mm or 8 mm transducer systems cannot be installed. In addition, the probe geometry supports rotor dynamics monitoring applications by measuring radial vibration, axial position, and shaft movement characteristics. The system configuration requires proper gap voltage validation during commissioning. Furthermore, Bently Nevada monitoring systems typically verify probe operating range through gap voltage measurements, including -10 VDC target reference conditions for correct eddy-current probe operation. Frequently Asked Questions Q: What monitoring system is compatible with the 330905-00-25-05-12-CN probe?A: The probe operates as part of the 3300 XL NSv Transducer System and requires a compatible 3300 XL NSv Proximitor Sensor and extension cable configuration. Q: Can this probe replace older 3300 RAM or 3000-series systems directly?A: The 3300 XL NSv system can replace 3300 RAM and 3000-series or 7000-series 190 Transducer Systems. However, upgrades may require replacement of the probe, extension cable, and Proximitor Sensor depending on the original system configuration. Q: Does the probe include armor protection?A: No. The 330905-00-25-05-12-CN uses a non-armored construction with a FluidLoc cable and miniature coaxial ClickLoc connector. Field Installation Guidelines Install the 330905-00-25-05-12-CN probe with the specified M10 x 1 thread engagement and maintain correct mechanical alignment with the rotating target surface. Route the probe cable away from high-current power conductors and electromagnetic interference sources. Use proper cable support to prevent mechanical stress at the connector interface. Connect the cable shield according to the monitoring system grounding practice. Avoid grounding methods that create additional ground loops between the probe system and machinery monitoring equipment. During commissioning, verify probe clearance, gap voltage, and signal response through the connected Proximitor Sensor. Confirm that the measured displacement signal remains within the expected operating range before enabling machine protection functions.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330905-06-14-10-02-00 3300 NSv Proximity Probe
Bently Nevada 330905-06-14-10-02-00 3300 NSv Proximity Probe The Bently Nevada 330905-06-14-10-02-00, also cataloged as the 330905 3300 NSv Proximity Probe, operates as a dedicated hardware component for shaft displacement measurement within the 3300 XL NSv Proximity Transducer System. Hardware Specifications Parameter Specification Model 330905-06-14-10-02-00 Brand Bently Nevada Product Type 3300 NSv Proximity Probe Origin USA Weight 0.14 kg Dimensions Estimated shipping size: 20.3 x 22 x 3.5 cm Operating Temp -52 deg C to +177 deg C Power Consumption Powered through compatible Proximitor Sensor, -17.5 VDC to -26 VDC supply range Probe Thread Type M10 x 1 metric thread Probe Construction Without stainless steel armor Transducer System 3300 XL NSv Proximity Transducer System Measurement Principle Eddy-current non-contact displacement measurement Unthreaded Length 60 mm Overall Case Length 140 mm Total Cable Length 1.0 m Connector Type Miniature coaxial ClickLoc connector Target Material AISI 4140 steel target Linear Range 1.5 mm Average Scale Factor 7.87 V/mm nominal Linearity Deviation +/- 38 um or better Eddy-Current Probe Scaling and Rotor Dynamics Monitoring The 330905-06-14-10-02-00 uses eddy-current probe scaling technology to convert shaft displacement into proportional electrical signals. Therefore, the connected Proximitor Sensor can process vibration and position measurements through the calibrated probe gap relationship. The probe system supports rotor dynamics analysis by providing shaft relative displacement data for vibration monitoring applications. Additionally, the measurement output depends on correct probe installation, target surface condition, and gap voltage validation. Bently Nevada systems commonly verify probe operation through gap voltage targets around -10 VDC during commissioning procedures. The 3300 NSv design reduces installation limitations in restricted mounting locations. Furthermore, the narrow side-view construction supports applications where standard probe body dimensions cannot meet mechanical clearance requirements. Frequently Asked Questions Q: What measurement technology does the 330905-06-14-10-02-00 use?A: The probe uses eddy-current sensing technology to measure relative shaft displacement without physical contact with the rotating target. Q: Does this probe include stainless steel armor protection?A: No. The 330905-06-14-10-02-00 configuration specifies a probe without stainless steel armor. Q: What electrical device processes the probe signal?A: The probe connects to a compatible 3300 XL NSv Proximitor Sensor, which provides signal conditioning and displacement output. Field Installation Guidelines Install the probe with the specified M10 x 1 mounting thread and maintain correct mechanical alignment with the shaft target surface. Verify the probe gap voltage after installation to confirm proper operating range before machine operation. Route the coaxial cable away from high-current power conductors to reduce electrical interference. Maintain proper cable shielding and grounding practices according to the monitoring system installation requirements. Confirm the target surface condition before commissioning because surface damage or contamination can affect eddy-current measurement accuracy. Avoid excessive cable bending near the miniature coaxial ClickLoc connector to prevent mechanical stress on the connection point.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330905-07-17-05-02-05 3300 NSv Proximity Probe
Bently Nevada 330905-07-17-05-02-05 3300 NSv Proximity Probe The Bently Nevada 330905-07-17-05-02-05, also cataloged as the 330905 3300 NSv Proximity Probe, operates as a dedicated hardware component for eddy-current shaft displacement measurement within the 3300 XL NSv Transducer System. Hardware Specifications Parameter Specification Model 330905-07-17-05-02-05 Brand Bently Nevada Product Type 3300 NSv Proximity Probe System Platform 3300 XL NSv Proximity Transducer System Origin USA Dimensions M10 x 1 thread; 70 mm unthreaded length; 170 mm overall case length Operating Temp -34 deg C to +177 deg C Storage Temp -51 deg C to +177 deg C Power Consumption Passive probe element; powered through compatible Proximity System interface Thread Type M10 x 1 metric thread Armor Type Without armor Total Cable Length 0.5 m Cable Type 75 ohm coaxial FEP insulated standard cable Connector Type Miniature coaxial ClickLoc connector Probe Case Material AISI 304 stainless steel Probe Tip Material Polyphenylene sulfide (PPS) Linear Range 1.5 mm (60 mils) Average Scale Factor 7.87 V/mm (200 mV/mil) Target Material AISI 4140 steel calibration target Frequency Response 0 to 10 kHz (-3 dB) Agency Approval Multiple approvals including CSA, ATEX, IECEx options Eddy-Current Measurement and Rotor Dynamics Monitoring The Bently Nevada 330905-07-17-05-02-05 uses eddy-current probe scaling to convert shaft displacement into proportional electrical output signals. The probe works with compatible 3300 XL NSv Proximitor modules to provide radial vibration and position measurement data. Additionally, the system requires gap voltage validation during commissioning. Technicians normally verify probe operation against the -10 VDC target gap voltage condition to confirm correct probe-to-shaft spacing. The narrow side-view construction supports rotor dynamics monitoring applications where installation clearance limits standard probe mounting. Furthermore, the probe design reduces installation interference when measuring small shafts below 51 mm or flat targets below 15 mm. Frequently Asked Questions Q: What measurement principle does the 330905-07-17-05-02-05 use?A: The probe uses eddy-current technology to measure relative shaft displacement through electromagnetic field variation between the probe tip and conductive target surface. Q: Does this probe include an armored cable design?A: No. The 330905-07-17-05-02-05 configuration uses a standard cable without armor protection. Q: What connector type does this proximity probe use?A: The probe uses a miniature coaxial ClickLoc connector designed for secure connection with compatible 3300 XL NSv system components. Field Installation Guidelines Install the probe with the correct M10 x 1 threaded mounting arrangement and maintain proper mechanical alignment between the probe tip and the measured shaft surface. Route the coaxial cable separately from high-current power conductors and variable frequency drive output cables to reduce electrical interference. Maintain proper cable bending practices to prevent damage to the FEP insulation and connector assembly. During commissioning, verify probe polarity, signal output, and gap voltage before placing the monitoring channel into service. Confirm that the probe tip faces the target surface without mechanical contact during machine operation. Connect the ClickLoc connector securely and verify that the cable shield follows the system grounding requirements specified for the 3300 XL NSv installation.
$200.00 $100.00
-
Bently Nevada 330908-12-31-10-02-00 Bently Nevada 3300 NSv Proximity Probe
Bently Nevada 330908-12-31-10-02-00 3300 NSv Proximity Probe The Bently Nevada 330908-12-31-10-02-00, also cataloged as the 330908 3300 NSv Proximity Probe, operates as a dedicated hardware component for eddy-current displacement measurement within the 3300 NSv Proximity Transducer System. The probe converts shaft target position changes into proportional voltage signals for vibration, position, and Keyphasor monitoring applications. Hardware Specifications Parameter Specification Model 330908-12-31-10-02-00 Brand Bently Nevada Product Type 3300 NSv Eddy Current Proximity Probe Origin USA Dimensions 3/8-24 UNF thread; 1.2 in unthreaded length; 3.1 in overall case length Operating Temp -34 deg C to +177 deg C Power Consumption Powered by compatible 3300 NSv Proximity Transducer System driver Thread Type 3/8-24 UNF-2A Armor Configuration Without armor Cable Length 1.0 m Cable Type 75 ohm coaxial cable with FEP insulation Connector Type Miniature coaxial ClickLoc connector Measurement Principle Eddy current displacement sensing Linear Range 1.5 mm (60 mils) Recommended Gap Setting 1.0 mm (40 mils) Incremental Scale Factor 7.87 V/mm (200 mV/mil) +/- 12.5% Output Voltage Range Approximately -1 VDC to -13 VDC Probe Tip Material Polyphenylene sulfide (PPS) Probe Body Material AISI 304 stainless steel Standard Target Material AISI 4140 steel Mounting Torque 11.3 N m (100 in lb) Eddy Current Probe Scaling and Rotor Dynamics Monitoring The 3300 NSv probe uses eddy-current sensing technology to measure shaft displacement relative to the probe tip. Therefore, the probe output follows a defined voltage displacement relationship with an incremental scale factor of 7.87 V/mm. The system supports rotor dynamics analysis by providing continuous shaft vibration and position feedback. In addition, the narrow side-view probe structure reduces side-wall interference when installed near small diameter targets, counterbores, and restricted bearing housings. Gap voltage validation remains a key installation procedure for accurate measurement. The 3300 NSv system typically verifies probe gap voltage near the -10 VDC target position to confirm correct operating clearance and signal linearity. Frequently Asked Questions Q: What measurement signals does the 330908-12-31-10-02-00 provide?A: The probe provides proportional voltage output related to shaft displacement and supports vibration, radial position, and Keyphasor measurement when connected to a compatible 3300 NSv driver system. Q: Can the probe operate without an extension cable?A: Yes. This model includes a 1.0 m integrated cable length. The final system configuration depends on the required distance between the probe and monitoring electronics. Q: What installation factors affect measurement accuracy?A: Proper probe gap adjustment, target material compatibility, cable routing, and electrical shielding practices directly affect displacement measurement accuracy. Field Installation Guidelines Install the probe with the specified 3/8-24 UNF mounting thread and maintain proper mechanical alignment with the rotating shaft target surface. Verify the probe gap voltage after mechanical installation. Adjust the probe position until the operating voltage falls within the intended range for the 3300 NSv system. Route the coaxial cable away from high-current power conductors and strong electromagnetic interference sources. Maintain proper cable shielding practices and connect the shield according to the monitoring system grounding requirements. Avoid excessive cable bending near the ClickLoc connector area. Confirm that the probe tip faces the target material directly and that the mounting structure does not introduce mechanical movement during operation.
$200.00 $100.00
-
Bently Nevada 330910-00-15-10-02-00 3300 NSv Proximity Probe Bently Nevada
Bently Nevada 330910-00-15-10-02-00 3300 NSv Proximity Probe Configured for shaft displacement and vibration signal measurement in the 3300 XL NSv Proximity Transducer System, the Bently Nevada 330910-00-15-10-02-00 (330910 3300 NSv Proximity Probe) provides direct eddy-current sensing execution for rotating machinery monitoring circuits. Hardware Specifications Parameter Specification Model 330910-00-15-10-02-00 Brand Bently Nevada Product Type 3300 NSv Proximity Probe System Compatibility 3300 XL NSv Proximitor Sensor and 3300 NSv Extension Cable Origin USA Dimensions 1.5 in case length, M10 x 1 metric thread Operating Temp -52 deg C to +177 deg C Storage Temp -52 deg C to +177 deg C Power Consumption 12 mA maximum current drain through Proximitor Sensor Probe Structure Flexible stainless steel armored proximity probe Thread Type M10 x 1 metric mounting thread Case Material AISI 304 stainless steel Probe Tip Material Polyphenylene sulfide (PPS) Cable Type 75 ohm triaxial FEP insulated cable with AISI 302/304 stainless steel armor Connector Type Gold-plated brass/beryllium copper miniature coaxial ClickLoc connector Scale Factor 7.87 V/mm (200 mV/mil) Average Scale Factor Linear Range 1.5 mm (60 mils) Frequency Response 0 to 2.7 kHz (+0, -3 dB typical) Power Supply Requirement -17.5 VDC to -26 VDC supplied by 3300 XL NSv Proximitor Sensor Mounting Torque Recommended 11.3 N m; maximum rated 33.9 N m Humidity Limit 100% condensing, non-submerged when connectors are sealed Eddy-Current Measurement and Rotor Dynamics Characteristics The 330910-00-15-10-02-00 uses eddy-current probe scaling to convert shaft-to-probe gap variations into proportional electrical output signals. Therefore, the probe supports dynamic vibration measurement and static shaft position monitoring within the 3300 XL NSv signal chain. The probe requires gap voltage validation during system commissioning. Engineers typically verify the probe operating point near the -10 VDC target condition to confirm correct mechanical installation and measurement range. Furthermore, the NSv sensing structure supports rotor dynamics analysis on compact rotating equipment. The probe geometry allows installation where standard proximity probes cannot fit, including small-diameter shafts and restricted side-view mounting locations. Frequently Asked Questions Q: What transducer components are required for operation with the 330910-00-15-10-02-00 probe?A: The probe requires a complete 3300 XL NSv Proximity Transducer System, including the 3300 NSv Extension Cable and 3300 XL NSv Proximitor Sensor. Q: Can the 330910 probe measure both vibration and axial position signals?A: Yes. The probe supports radial vibration measurement on shafts smaller than 51 mm and axial position measurement on targets smaller than 15 mm when installed within specified mechanical conditions. Q: Does the probe require special installation considerations for signal accuracy?A: Yes. Installation requires correct probe gap setting, proper cable routing, and connector sealing to maintain electrical signal integrity and environmental protection. Field Installation Guidelines Install the M10 x 1 threaded probe body with the specified mounting torque to prevent mechanical loosening or thread damage. Maintain proper probe tip clearance from the target surface before connecting the extension cable and Proximitor Sensor. Route the armored cable away from high-current power conductors and strong electromagnetic interference sources. Verify connector engagement and ensure the ClickLoc connector remains properly secured during operation. Confirm the probe gap voltage during commissioning and validate the signal output before placing the monitoring channel into service. Avoid sharp cable bending near the probe body and connector interface to protect the triaxial cable structure.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330910-00-18-10-02-00 3300 NSv Proximity Probe
Bently Nevada 330910-00-18-10-02-00 3300 NSv Proximity Probe The Bently Nevada 330910-00-18-10-02-00, also cataloged as the 330910 3300 NSv Proximity Probe, operates as a dedicated hardware component for shaft displacement measurement and vibration monitoring within the 3300 XL NSv Proximity Transducer System. Hardware Specifications Parameter Specification Model 330910-00-18-10-02-00 Brand Bently Nevada Product Type 3300 NSv Eddy Current Proximity Probe Origin USA Dimensions M10 x 1 thread, 180 mm overall case length, 1.0 m system length Operating Temp -51 deg C to +177 deg C Power Consumption Supplied by compatible 3300 XL NSv Proximitor system System Technology Eddy current displacement measurement Thread Type Metric M10 x 1 Cable Protection Flexible stainless steel armor Probe Tip Material Polyphenylene sulfide (PPS) Case Material AISI 304 stainless steel Connector Type Gold-plated miniature coaxial ClickLoc connector Target Material AISI 4140 steel standard calibration Linear Range 1.5 mm nominal Scale Factor 7.87 V/mm (200 mV/mil) Cable Resistance 75 ohm coaxial FEP insulated cable Relative Humidity 100% condensing, non-submerged Eddy Current Probe Scaling and Rotor Dynamics Monitoring The 330910-00-18-10-02-00 uses eddy-current probe scaling to convert shaft position changes into proportional electrical signals. The system maintains a nominal scale factor of 7.87 V/mm (200 mV/mil) for displacement measurement. Furthermore, the probe supports rotor dynamics analysis by providing shaft vibration and axial position data to compatible monitoring modules. The ClickLoc connector design maintains the coaxial signal path during mechanical vibration conditions. The armored cable construction reduces mechanical damage risks in restricted installation areas. The 3300 XL NSv system requires correct gap voltage validation during commissioning. Engineers typically verify probe operating conditions against the -10 VDC gap voltage target range used for standard Bently Nevada proximity measurement calibration. Frequently Asked Questions Q: What measurement principle does the Bently Nevada 330910-00-18-10-02-00 use?A: The probe uses eddy-current technology to measure the distance between the probe tip and conductive shaft surface, generating proportional displacement signals. Q: Can this probe replace a standard 8 mm proximity probe?A: No. The 330910 series uses a Narrow Side View design for applications requiring reduced installation clearance and is configured specifically for 3300 XL NSv systems. Q: What connector type does this probe use?A: The probe uses a miniature coaxial ClickLoc connector with a gold-plated contact design for connection to compatible extension cables and Proximitor systems. Field Installation Guidelines Install the probe with the M10 x 1 threaded body fully secured according to the mechanical drawing requirements of the application. Maintain correct probe tip orientation toward the measurement target surface. Avoid mechanical contact between the probe tip and rotating components during installation and operation. Route the armored coaxial cable away from high-current power conductors to reduce electromagnetic interference. Connect the cable shield according to the monitoring system grounding practice. Before operation, verify probe gap voltage, signal polarity, and system calibration using compatible Bently Nevada diagnostic equipment. Confirm that the probe, extension cable, and Proximitor module form a matched electrical system.
$200.00 $100.00
-
Bently Nevada 330910-07-23-10-02-00 | Bently Nevada | 3300 NSv Proximity Probe
Bently Nevada 330910-07-23-10-02-00 3300 NSv Proximity Probe The Bently Nevada 330910-07-23-10-02-00, also cataloged as the 330910 3300 NSv Proximity Probe, operates as a dedicated hardware component for eddy-current displacement measurement within the 3300 NSv Proximity Transducer System. Hardware Specifications Parameter Specification Model 330910-07-23-10-02-00 Brand Bently Nevada Product Type 3300 NSv Proximity Probe Origin USA Dimensions 70 mm unthreaded length, 230 mm overall case length Operating Temp -51 deg C to +177 deg C Power Consumption Supplied through 3300 XL NSv Proximitor Sensor, -17.5 VDC to -26 VDC Thread Size M10 x 1 Probe Series 3300 NSv Narrow Side View Proximity System Cable Length 1.0 meter (39 in) Connector Type Miniature coaxial ClickLoc connector Connector Material Gold-plated brass Probe Case Material AISI 304 stainless steel Armor Material AISI 302 stainless steel flexible armor Probe Tip Material Polyphenylene Sulfide (PPS) Linear Range 1.5 mm (60 mils) Target Scale Factor 7.87 V/mm (200 mV/mil) average Frequency Response 0 to 10 kHz (+0, -3 dB typical) Recommended Target Material AISI 4140 steel Target Compatibility Shaft diameter less than 51 mm (2 in), axial target diameter less than 15 mm (0.6 in) Eddy-Current Measurement and Rotor Dynamics Characteristics The 330910-07-23-10-02-00 uses eddy-current probe scaling to convert shaft displacement into proportional electrical output signals. The probe maintains a nominal scale factor of 7.87 V/mm for vibration and axial position monitoring applications. Furthermore, the 3300 NSv system supports gap voltage validation through the Proximitor Sensor output, where technicians verify probe operating position near the typical -10 VDC target condition. This measurement confirms proper probe gap adjustment before machinery operation. The narrow side view construction reduces installation restrictions in compact assemblies. Therefore, the probe supports rotor dynamics monitoring where limited radial clearance prevents installation of standard proximity probe designs. The shielded miniature coaxial connection helps reduce signal interference during high-frequency vibration measurement. Frequently Asked Questions Q: What measurement principle does the 330910-07-23-10-02-00 use?A: The probe uses an eddy-current sensing principle to measure shaft displacement and provide dynamic vibration or axial position signals through the 3300 NSv Proximity Transducer System. Q: Can the probe operate directly without a Proximitor Sensor?A: No. The probe requires a compatible 3300 XL NSv Proximitor Sensor to provide excitation and process the eddy-current measurement signal. Q: What installation factor must technicians verify during commissioning?A: Technicians should verify probe gap voltage, mechanical alignment, target material compatibility, cable routing, and connector installation condition before system operation. Field Installation Guidelines Install the M10 x 1 threaded probe into the prepared mounting location while maintaining correct mechanical alignment with the measurement target. Verify the unthreaded probe length and case dimensions before installation to prevent interference with surrounding machine components. Maintain proper separation between probe cable routing and high-current power conductors to reduce electrical noise coupling. Connect the miniature coaxial ClickLoc connector securely and inspect the cable armor for mechanical damage before commissioning. Confirm the probe gap voltage through the connected Proximitor Sensor and adjust the mounting position according to the required operating range. Use compatible target materials, such as AISI 4140 steel, to maintain specified eddy-current measurement characteristics. Ground cable shielding according to the machinery monitoring system installation requirements and avoid unnecessary shield loops.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330930-040-00-00 3300 NSv Extension Cable
Bently Nevada 330930-040-00-00 3300 NSv Extension Cable The Bently Nevada 330930-040-00-00, also cataloged as the 3300 NSv Extension Cable, operates as a dedicated hardware component for signal transmission between proximity probes and proximitor sensors within the 3300 NSv Eddy Current Proximity Transducer System. Hardware Specifications Parameter Specification Model 330930-040-00-00 Brand Bently Nevada Product Type 3300 NSv Extension Cable Origin USA Weight 0.05 kg Dimensions 17 x 17 x 1.5 cm estimated shipping size Operating Temp -52 deg C to +177 deg C Storage Temp -52 deg C to +177 deg C Power Consumption Passive cable, no external power consumption Cable Length 4.0 meters (13.1 feet) Cable Material 75 Ohm coaxial cable with FEP insulation Connector and Cable Option Without stainless steel armor Agency Approval Option Not required Tariff Code 8537101190 Place of Shipment Xiamen, China System Compatibility Bently Nevada 3300 NSv Eddy Current Proximity Transducer System Eddy-Current Signal Scaling and Rotor Monitoring Characteristics The Bently Nevada 330930-040-00-00 extension cable maintains the electrical characteristics required for 3300 NSv eddy-current measurement circuits. Therefore, it supports accurate probe signal transfer between the proximity probe and proximitor module without altering the calibrated measurement relationship. The 3300 NSv system uses eddy-current probe scaling technology to convert shaft displacement into electrical output signals. Additionally, the cable construction supports stable gap voltage transmission and measurement validation, including standard proximity system checks around -10 VDC gap voltage targets. The 3300 NSv extension cable supports rotor dynamics monitoring applications by preserving vibration and position signal integrity. Moreover, the 75 Ohm coaxial design and FEP insulation provide controlled impedance characteristics for rotating machinery monitoring circuits. Frequently Asked Questions Q: What equipment uses the Bently Nevada 330930-040-00-00 cable?A: The cable connects components within the Bently Nevada 3300 NSv Eddy Current Proximity Transducer System, typically between an NSv probe and its associated proximitor sensor. Q: Does the 330930-040-00-00 extension cable require external power?A: No. The extension cable is a passive signal transmission component and does not consume external electrical power. Q: What environmental temperature range does this cable support?A: The cable supports operating and storage temperatures from -52 deg C to +177 deg C. Field Installation Guidelines Install the 330930-040-00-00 cable according to the 3300 NSv system installation requirements. Keep the cable routing away from high-voltage power conductors and strong electromagnetic interference sources to reduce signal disturbance. Maintain the specified connector engagement between the probe, extension cable, and proximitor interface. Inspect connector surfaces before installation and prevent contamination on signal contacts. Use proper shielding and grounding practices for the proximity measurement circuit. Avoid sharp bends, mechanical stress, and excessive pulling force on the coaxial cable during installation. Verify the complete probe-extension cable-proximitor assembly after installation. Confirm correct gap voltage behavior and signal output before placing the monitored machinery into operation.
$200.00 $100.00
-
Bently Nevada 330930-040-02-00 | 3300 NSv Extension Cable | Bently Nevada
Bently Nevada 330930-040-02-00 3300 NSv Extension Cable The Bently Nevada 330930-040-02-00, also cataloged as the 3300 NSv Extension Cable, operates as a dedicated hardware component for signal transmission between proximity probes and monitoring modules within the 3300 NSv Transducer System. Hardware Specifications Parameter Specification Model 330930-040-02-00 Brand Bently Nevada Product Type 3300 NSv Extension Cable Origin USA Weight 0.18 kg Dimensions 20.4 x 22 x 3 cm (shipping size) Power Consumption Passive cable component, no external power consumption Cable Length 4.0 meters (13.1 feet) Cable Construction Stainless steel armor, without FEP jacket Connector Option Standard extension cable configuration Tariff Code 8537101190 Eddy-Current Signal Transmission and Rotor Monitoring Integration The 330930-040-02-00 extension cable transfers eddy-current probe signals between the 3300 NSv proximity probe and the associated monitoring system. Therefore, it maintains the electrical characteristics required for accurate shaft displacement and vibration measurement. The stainless steel armor provides mechanical protection for cable routing in industrial environments. Additionally, the cable design supports stable signal transmission while reducing the influence of external mechanical stress and installation conditions. The 3300 NSv system applies probe scaling and gap voltage validation methods to verify measurement conditions. The extension cable maintains the probe circuit connection required for proper gap voltage evaluation, including typical -10 VDC target reference conditions used in eddy-current measurement systems. Frequently Asked Questions Q: What is the function of the Bently Nevada 330930-040-02-00 cable in the 3300 NSv system?A: The cable extends the connection distance between the 3300 NSv proximity probe and the monitoring electronics while maintaining the probe signal characteristics. Q: Does the 330930-040-02-00 require external power?A: No. The extension cable is a passive component and does not consume external electrical power. Q: What installation factors should be considered for this extension cable?A: Installers should maintain proper cable routing, avoid excessive mechanical stress, and follow shielding and grounding practices required for eddy-current measurement circuits. Field Installation Guidelines Install the extension cable according to the 3300 NSv system wiring requirements. Maintain separation from high-voltage power cables to reduce electromagnetic interference. Connect shielding and grounding according to the monitoring system installation documentation. Avoid sharp bends, excessive pulling force, or mechanical damage to the stainless steel armor. Verify connector engagement and cable continuity before commissioning the proximity measurement circuit.
$200.00 $100.00
-
Bently Nevada 330930-045-03-CN | 3300 NSv Extension Cable | Bently Nevada
Bently Nevada 330930-045-03-CN 3300 NSv Extension Cable Configured for proximity signal transmission in the Bently Nevada 3300 NSv Proximity Transducer System, the Bently Nevada 330930-045-03-CN (330930 Extension Cable) provides direct electrical connection between the NSv proximity probe and Proximitor Sensor assemblies. The cable transfers eddy-current measurement signals for vibration and shaft position monitoring. Hardware Specifications Parameter Specification Model Bently Nevada 330930-045-03-CN Brand Bently Nevada Product Type 3300 NSv Extension Cable Origin USA Operating Temp -51 deg C to +177 deg C Power Consumption Passive cable component; no external power consumption System Compatibility 3300 NSv Proximity Probes and Proximitor Sensors / 990 / 991 Transmitters Cable Length 4.5 m (14.8 ft) Cable Construction FEP insulated coaxial cable with stainless steel armor Armor Material Flexible AISI 302 / 304 stainless steel armor Connector Type Miniature coaxial ClickLoc connectors with gold-plated brass contacts Characteristic Impedance 75 Ohm coaxial cable System Scale Factor 7.87 V/mm (200 mV/mil) with complete NSv system Capacitance 69.9 pF/m (21.3 pF/ft) typical Center Conductor Resistance 0.220 Ohm/m (0.067 Ohm/ft) Shield Resistance 0.066 Ohm/m (0.020 Ohm/ft) Minimum Bend Radius 25.4 mm (1.0 in) Humidity Limit 100% condensing, non-submerged with protected connectors Hazardous Area Approval NEPSI / CCC / ATEX / IECEx / CSA depending on regional certification Eddy-Current Signal Scaling and Rotor Dynamics Interface The 330930-045-03-CN extension cable maintains the electrical characteristics required for Bently Nevada eddy-current measurement systems. It preserves probe signal scaling between the proximity probe and Proximitor Sensor, allowing the system to convert shaft displacement into proportional voltage output. In addition, the cable supports rotor dynamics monitoring by maintaining stable impedance, shielding performance, and signal transmission quality. Therefore, the cable configuration helps reduce measurement errors caused by cable electrical variation during vibration and axial position monitoring. Frequently Asked Questions Q: What equipment connects with the Bently Nevada 330930-045-03-CN cable?A: The cable connects 3300 NSv proximity probes with compatible Proximitor Sensors or 990 / 991 transmitters within the proximity transducer system. Q: Does the extension cable require an external power supply?A: No. The extension cable is a passive signal transmission component and receives operating power through the connected Proximitor Sensor circuit. Q: How should the cable shielding be installed in the field?A: Install the cable according to Bently Nevada system wiring practices. Maintain shield continuity, avoid unnecessary cable routing near high-noise power conductors, and protect connector interfaces from contamination. Field Installation Guidelines Install the extension cable with the specified minimum bend radius to prevent mechanical stress on the coaxial structure. Connect ClickLoc connectors firmly to maintain electrical contact integrity and signal stability. Keep the cable routing separated from high-current switching cables to reduce electromagnetic interference. Maintain proper armor grounding practices according to site electrical standards. Verify probe, extension cable, and Proximitor Sensor compatibility before system commissioning. Inspect connector protectors during installation to prevent moisture and contamination ingress.
$200.00 $100.00
-
Bently Nevada 330930-060-00-00 Bently Nevada 3300 NSv Extension Cable
Bently Nevada 330930-060-00-00 3300 NSv Extension Cable The Bently Nevada 330930-060-00-00, also cataloged as the 330930 Standard Extension Cable, provides signal transmission between proximity probe assemblies and monitoring instrumentation within the Bently Nevada 3300 NSv transducer system. Hardware Specifications Parameter Specification Model 330930-060-00-00 Brand Bently Nevada Product Type 3300 NSv Extension Cable Origin USA Weight 0.18 kg Dimensions 20.3 x 22 x 3.5 cm estimated shipping size Power Consumption Passive cable component, no external power consumption Cable Length 6.0 meters (19.7 feet) Cable Armor Option Without stainless steel armor Output Resistance 50 Ohm Extension Cable Capacitance 69.9 pF/m (21.3 pF/ft) typical Tariff Code 8537101190 Eddy-Current Signal Transmission Characteristics The Bently Nevada 330930-060-00-00 extension cable maintains the electrical characteristics required for 3300 NSv proximity measurement circuits. Therefore, the cable length and capacitance values support proper eddy-current probe scaling between the sensor and monitoring module. The cable provides a controlled impedance path with a 50 Ohm output resistance. In addition, the 69.9 pF/m typical capacitance value supports gap voltage validation and vibration signal transfer for rotor dynamics monitoring applications. The extension cable operates as a passive component in the proximity transducer loop. Consequently, it does not require firmware configuration, external power input, or communication addressing. Frequently Asked Questions Q: What system components connect with the Bently Nevada 330930-060-00-00 cable?A: The cable connects 3300 NSv proximity probes with compatible Bently Nevada monitoring instruments in an eddy-current displacement measurement circuit. Q: Does the 330930-060-00-00 require external power?A: No. The extension cable is a passive electrical component and receives operating excitation through the connected proximity transducer system. Q: What installation factors affect signal performance?A: Cable routing, shielding practices, connector protection, and separation from high-noise electrical conductors affect signal integrity. Field Installation Guidelines Install the extension cable according to the applicable Bently Nevada 3300 NSv system wiring requirements. Maintain separation between the probe cable and high-current power conductors to reduce electromagnetic interference. Verify connector conditions before installation and prevent contamination or mechanical stress on connection points. Maintain proper cable routing without sharp bends or excessive mechanical tension. Confirm the connected probe and monitoring module compatibility before system commissioning. Check signal behavior and gap voltage readings after installation to verify correct transducer loop operation.
$200.00 $100.00
-
Bently Nevada 330930-060-00-05 | Bently Nevada | 3300 NSv Extension Cable
Bently Nevada 330930-060-00-05 3300 NSv Extension Cable The Bently Nevada 330930-060-00-05, also cataloged as the 330930 3300 NSv Extension Cable, operates as a dedicated hardware component for signal transmission between a 3300 NSv proximity probe and monitoring system interface. Hardware Specifications Parameter Specification Model 330930-060-00-05 Brand Bently Nevada Product Type 3300 NSv Extension Cable Origin USA Weight 0.18 kg Dimensions 20.5 x 22.2 x 3.3 cm (estimated shipping size) Operating Temp Not specified Power Consumption Passive cable assembly, no external power consumption Cable Length 6.0 meters (19.7 feet) Connector Protector and Cable Option Without stainless steel armor Agency Approval Option Multiple Approvals Recommended Gap Setting 1.27 mm (50 mils) Extension Cable Capacitance 69.9 pF/m (21.3 pF/ft) typical Tariff Code 8537101190 Shipment Location Xiamen, China Eddy-Current Signal Transmission and Rotor Dynamics Interface The 3300 NSv extension cable maintains electrical continuity between the proximity probe and the monitoring electronics. Therefore, it supports accurate eddy-current probe scaling by preserving the probe system impedance characteristics and signal response. The cable assembly operates with the recommended 1.27 mm (50 mils) gap setting used for 3300 NSv proximity measurement systems. Additionally, the specified cable capacitance of 69.9 pF/m helps maintain the calibrated electrical behavior required for shaft displacement and vibration measurement. For rotor dynamics monitoring applications, the cable routing directly affects measurement stability. Installers should minimize mechanical stress, avoid sharp bends, and maintain separation from high-current conductors to reduce possible signal interference. Frequently Asked Questions Q: What is the primary function of the Bently Nevada 330930-060-00-05 cable?A: The cable extends the connection between a 3300 NSv proximity probe and the associated monitoring electronics while maintaining the specified electrical characteristics. Q: Does the 330930-060-00-05 include stainless steel armor protection?A: No. This configuration uses a cable design without stainless steel armor. Q: What gap setting does this extension cable configuration support?A: The recommended probe gap setting is 1.27 mm (50 mils) for compatible 3300 NSv proximity transducer systems. Field Installation Guidelines Install the cable according to the approved 3300 NSv transducer system wiring arrangement. Maintain proper cable routing distance from power cables, motor leads, and high-frequency switching sources. Avoid excessive bending, twisting, or pulling force during installation. Verify connector condition before installation and keep connection points free from contamination. Confirm the probe gap voltage and mechanical positioning after completing installation. Use appropriate shielding and grounding practices according to the monitoring system installation requirements.
$200.00 $100.00
-
Bently Nevada 330930-060-01-CN 3300 XL Standard Extension Cable | Bently Nevada
Bently Nevada 330930-060-01-CN 3300 XL Standard Extension Cable The Bently Nevada 330930-060-01-CN, also cataloged as the 330930 3300 XL Standard Extension Cable, provides electrical signal extension between proximity probes and monitoring modules within 3300 XL and 3300 NSv Proximity Transducer Systems. Hardware Specifications Parameter Specification Model 330930-060-01-CN Brand Bently Nevada Product Type 3300 XL Standard Extension Cable Origin USA Weight Approx. 0.55 kg Dimensions Approx. 20.5 x 22.5 x 3.5 cm Operating Temp -51 deg C to +177 deg C Power Consumption Passive cable assembly, no external power required System Compatibility 3300 XL and 3300 NSv Proximity Transducer Systems Cable Length 6.0 m (19.7 ft) Cable Construction FEP insulated coaxial cable with stainless steel flexible armor Connector Type Miniature coaxial ClickLoc connector with connector protector Impedance 75 ohm Capacitance Approx. 69.9 pF/m Center Conductor Resistance Approx. 0.220 ohm/m Tensile Strength Minimum 220 N cable-to-connector pull strength Hazardous Area Approval ATEX, IECEx, and Chinese NEPSI certification option Eddy-Current Signal Transmission and Rotor Dynamics Interface The 330930-060-01-CN extension cable maintains the electrical characteristics required for Bently Nevada eddy-current probe systems. Therefore, it preserves probe scaling accuracy, gap voltage measurement stability, and vibration signal transmission between the proximity probe and monitoring hardware. The cable assembly supports rotor dynamics monitoring by transferring dynamic shaft displacement signals and static position measurements without adding active electronic processing. Additionally, the controlled impedance and capacitance values maintain compatibility with 3300 XL signal conditioning circuits. The system validates probe operating conditions through gap voltage measurement, where typical eddy-current probe systems use negative DC bias signals such as -10 VDC targets to confirm correct probe positioning and measurement range. Frequently Asked Questions Q: Can the 330930-060-01-CN extension cable operate without external power? A: Yes. The cable is a passive coaxial extension component and does not require an independent power supply. The connected proximity transducer system provides the excitation and signal processing functions. Q: Does the cable support hazardous area installation? A: Yes. The -CN option provides hazardous area approvals including ATEX, IECEx, and Chinese NEPSI certifications when installed according to the applicable system requirements. Q: What installation factors affect eddy-current measurement performance? A: Cable routing, connector condition, shielding integrity, and proper separation from high-current conductors affect signal quality. Installers should avoid mechanical stress and electromagnetic interference sources. Field Installation Guidelines Install the extension cable between the compatible Bently Nevada proximity probe and monitoring interface according to the approved system wiring configuration. Maintain the stainless steel armored section protection during routing to prevent mechanical damage. Avoid sharp bends, excessive pulling force, and continuous vibration points that may stress the connector assembly. Keep the coaxial cable separated from high-voltage power cables and high-frequency switching sources. Verify ClickLoc connector engagement and inspect the connector protector before commissioning. Confirm probe gap voltage and signal response after installation using the connected monitoring system.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330930-065-02-00 3300 NSv Extension Cable
Bently Nevada 330930-065-02-00 3300 NSv Extension Cable The Bently Nevada 330930-065-02-00, also cataloged as the 3300 NSv Extension Cable, provides signal extension between the 3300 NSv proximity probe and the associated Proximitor sensor within Bently Nevada monitoring systems. It uses a 6.5 m cable length with stainless steel armor for mechanical protection. Hardware Specifications Parameter Specification Model 330930-065-02-00 Brand Bently Nevada Product Type 3300 NSv Extension Cable Origin USA Weight 0.55 kg Dimensions Estimated shipping size: 20.5 x 22.5 x 3.5 cm Operating Temp -52 deg C to +177 deg C Storage Temp -52 deg C to +177 deg C Cable Length 6.5 m (21.3 ft) Cable Construction Stainless steel armor, without FEP jacket Maximum Torque 0.56 N m (5 in lb) Recommended Torque Finger tight Power Consumption Passive extension cable, no external power consumption Eddy-Current Signal Extension and Rotor Dynamics Interface The Bently Nevada 3300 NSv extension cable transfers eddy-current probe signals between the probe assembly and the Proximitor sensor. Therefore, the cable maintains the electrical characteristics required for accurate displacement measurement and rotor position monitoring. The stainless steel armored construction protects the cable from mechanical impact and installation stress. Additionally, the cable routing design supports vibration monitoring applications where rotor dynamics analysis depends on stable probe signal transmission. The 3300 NSv system uses probe gap voltage validation with -10 VDC target conditions during standard calibration procedures. The extension cable maintains the signal path required for proper gap voltage measurement and monitoring accuracy. Frequently Asked Questions Q: What is the primary function of the 330930-065-02-00 cable?A: The cable extends the connection distance between a 3300 NSv proximity probe and the Proximitor sensor while maintaining the eddy-current measurement signal path. Q: Does the 330930-065-02-00 require external power?A: No. The extension cable is a passive component and does not consume electrical power. Q: What installation consideration applies to the stainless steel armored cable?A: Installers should avoid excessive bending, protect the cable from mechanical damage, and follow standard shielding and grounding practices for vibration monitoring circuits. Field Installation Guidelines Install the cable according to the approved 3300 NSv transducer system wiring arrangement. Maintain proper separation from high-current power cables to reduce electromagnetic interference. Avoid sharp bends or mechanical stress that may damage the armored cable structure. Connect cable shielding according to the monitoring system grounding requirements. Tighten connections using the recommended finger-tight installation method unless system documentation specifies otherwise. Verify probe signal continuity and gap voltage values during commissioning.
$200.00 $100.00
-
Bently Nevada 330901-00-40-05-02-05 3300 NSv Proximity Probe | Bently Nevada
Bently Nevada 330901-00-40-05-02-05 3300 NSv Proximity Probe The Bently Nevada 330901-00-40-05-02-05, also cataloged as the 330901 3300 NSv Proximity Probe, operates as a dedicated hardware component for non-contact shaft displacement measurement within Bently Nevada 3300 NSv monitoring systems. Hardware Specifications Parameter Specification Model 330901-00-40-05-02-05 Brand Bently Nevada Product Type 3300 NSv Proximity Probe Origin USA Weight 0.14 kg Dimensions Estimated shipping size: 20.3 x 22 x 3.5 cm Thread Type 1/4-28 UNF thread Armor Type Without armor Unthreaded Length 0.0 in Overall Case Length 4.0 in Total Length 0.5 meter (20 in) Connector Type Miniature coaxial ClickLoc connector standard cable Agency Approval Multiple Approvals Power Consumption Passive eddy-current sensing element; excitation provided by compatible proximity transducer interface Eddy-Current Probe Scaling and Rotor Dynamics The 3300 NSv Proximity Probe uses eddy-current sensing technology to measure shaft displacement without mechanical contact. The probe generates a proportional electrical output according to the target distance, allowing the monitoring system to process vibration and position signals. Additionally, the probe design supports rotor dynamics measurement applications where shaft movement, radial vibration, and axial position changes require continuous monitoring. The miniature coaxial ClickLoc connector maintains signal transmission integrity between the probe and extension cable assembly. The system requires correct gap voltage adjustment during installation. Bently Nevada proximity systems typically validate probe operating range through gap voltage measurement, with -10 VDC targets used as a standard reference point for probe positioning verification. Frequently Asked Questions Q: What mechanical interface does the 330901-00-40-05-02-05 probe use?A: The probe uses a 1/4-28 UNF threaded body with a 0.0 in minimum unthreaded length and a 4.0 in overall case length. Q: What cable connection does this probe support?A: This model uses a miniature coaxial ClickLoc connector with a standard cable configuration. Q: Does this probe include armored construction?A: No. The 330901-00-40-05-02-05 configuration specifies a non-armored probe design. Field Installation Guidelines Install the probe with the specified 1/4-28 UNF thread engagement and maintain proper mechanical alignment with the monitored shaft target. Route the miniature coaxial cable away from high-current conductors, switching devices, and sources of electromagnetic interference. Use appropriate cable support to prevent mechanical stress on the ClickLoc connector. Verify the probe gap voltage after installation to confirm that the sensing element operates within the intended measurement range. Connect the probe to a compatible Bently Nevada proximity monitoring channel before performing vibration or position calibration procedures. Avoid modifying the probe housing, connector assembly, or cable termination because these changes can affect eddy-current signal scaling accuracy.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330130-085-02-05 3300 XL 8mm Extension Cable
Bently Nevada 330130-085-02-05 3300 XL 8mm Extension Cable The Bently Nevada 330130-085-02-05, also cataloged as the 330130 3300 XL 8mm Extension Cable, operates as a dedicated hardware component for proximity signal transmission and probe-to-sensor connection within the Bently Nevada 3300 XL 8mm Proximity Transducer System. Hardware Specifications Parameter Specification Model 330130-085-02-05 Brand Bently Nevada Product Type 3300 XL 8mm Extension Cable Origin USA Weight 0.3 kg Dimensions Estimated shipping size: 20 x 20 x 3 cm Operating Temp Extended temperature range applications Power Consumption Passive cable assembly, no external power consumption Cable Length 8.0 meters (26.2 feet) Cable Option Standard cable Connector Protector Option 00 Standard cable Agency Approval CSA, ATEX, IECEx approvals Output Resistance 50 ohm Minimum Bend Radius 50.8 mm (2 in) System Compatibility 3300 XL 8mm Probe, 3300 XL Extension Cable, 3300 XL Proximitor Sensor Signal Type Eddy-current proximity measurement signal Measurement Function Static position and dynamic vibration measurement Eddy-Current Signal Scaling and Rotor Dynamics Monitoring The Bently Nevada 3300 XL 8mm Extension Cable maintains the electrical characteristics required for eddy-current probe scaling within the complete proximity transducer circuit. Therefore, it supports accurate conversion between probe gap distance and output voltage from the connected Proximitor Sensor. The cable assembly preserves signal integrity for rotor dynamics applications by maintaining stable impedance and controlled transmission characteristics. In addition, the 50 ohm output resistance supports proper matching between the 3300 XL probe, extension cable, and Proximitor Sensor. The 3300 XL system uses gap voltage validation with -10 VDC target conditions to verify correct probe operating position. Furthermore, the extension cable design supports vibration, axial position, Keyphasor reference, and speed measurement circuits. Frequently Asked Questions Q: What components connect with the 330130-085-02-05 extension cable?A: The 330130-085-02-05 connects a 3300 XL 8mm proximity probe to a 3300 XL Proximitor Sensor as part of the complete transducer system. Q: Does the 330130-085-02-05 require external power?A: No. The extension cable is a passive signal transmission component and does not require independent power input. Q: Can the cable be mixed with other 3300 XL 8mm system components?A: Yes. The 3300 XL 8mm system supports interchangeability between compatible probes, extension cables, and Proximitor Sensors without individual bench calibration. Field Installation Guidelines Install the 330130-085-02-05 cable according to the mechanical requirements of the 3300 XL 8mm proximity transducer system. Route the extension cable away from high-current power cables and strong electromagnetic interference sources. Maintain the specified minimum bend radius of 50.8 mm (2 in) during installation. Verify connector engagement and mechanical protection before system commissioning. Ensure proper cable shielding and grounding practices according to site electrical standards. Confirm probe, extension cable, and Proximitor Sensor compatibility before operation. Avoid excessive mechanical stress, sharp bends, and vibration-induced cable movement.
$200.00 $100.00
-
Honeywell MU-NKD020 | Honeywell | Control Network Extension Cable
Honeywell MU-NKD020 Control Network Extension Cable Configured for signal and power extension between control modules in Honeywell TDC 3000 and Experion PKS systems, the Honeywell MU-NKD020 (MU-NKD020 Control Network Extension Cable) provides direct physical connection through pre-terminated industrial cable assemblies. Hardware Specifications Parameter Specification Model MU-NKD020 Brand Honeywell Part Number 51195153-020 Origin USA Component Type Control Network / I/O Extension Cable System Compatibility Honeywell TDC 3000 / Experion PKS platforms Cable Length 20 feet (approx. 6.1 meters) Power Consumption Passive cable assembly; no external power consumption Shielding Industrial EMI/RFI shielded cable construction Conductor Material Tinned copper conductors Connector Type Factory-installed multi-pin industrial connectors Application I/O processor, FTA, and network extension interconnection DCS Signal Integrity and Field Connection Characteristics The Honeywell MU-NKD020 uses a shielded cable construction to maintain electrical signal quality between distributed control system hardware assemblies. The cable provides a physical transmission path for control and I/O connections while limiting external electromagnetic interference from nearby industrial equipment. Furthermore, Honeywell DCS cable assemblies support stable field signal routing requirements in systems containing analog and digital process interfaces. The cable design complements Honeywell process control architectures that may include 4-20 mA HART loop devices, FOUNDATION Fieldbus segments, or Profibus PA field networks through associated interface hardware. The factory-terminated connector configuration reduces wiring errors during cabinet installation. In addition, the cable shielding layer requires proper grounding practices to minimize noise coupling between control circuits and power equipment. Frequently Asked Questions Q: Does the MU-NKD020 cable require an external power supply?A: No. The MU-NKD020 is a passive cable assembly and does not contain active electronic circuits or require external power input. Q: Can the MU-NKD020 be installed with standard field wiring practices?A: The cable should follow industrial installation practices, including separation from high-voltage power cables and correct shield termination according to system cabinet requirements. Q: Is the MU-NKD020 compatible with Honeywell TDC 3000 and Experion PKS hardware?A: The MU-NKD020 is specified for Honeywell TDC 3000 and Experion PKS control system environments as an extension cable assembly for compatible hardware connections. Field Installation Guidelines Verify the cable part number and connector configuration before installation into the control cabinet. Route the MU-NKD020 away from high-current power conductors, variable frequency drive cables, and sources of electromagnetic noise. Maintain proper cable bend radius to prevent mechanical stress on connectors and cable jackets. Connect cable shields according to the grounding method defined for the Honeywell control system cabinet. Inspect connector pins and locking mechanisms before operation to prevent intermittent communication faults. Confirm correct module and FTA termination points before system startup and signal verification.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330104-00-08-90-02-05 3300 XL 8 mm Proximity Probe
Bently Nevada 330104-00-08-90-02-05 3300 XL 8 mm Proximity Probe The Bently Nevada 330104-00-08-90-02-05, also cataloged as the 3300 XL 8 mm Proximity Probe, operates as a dedicated hardware component for eddy-current displacement measurement and rotor position monitoring within the Bently Nevada 3300 XL Machinery Protection System. Hardware Specifications Parameter Specification Model 330104-00-08-90-02-05 Brand Bently Nevada Product Type 3300 XL 8 mm Proximity Probe Origin USA Weight 0.12 kg Dimensions Estimated shipping size: 32 x 30 x 2 cm Power Consumption Supplied through compatible Proximitor Sensor system Probe Diameter 8 mm Thread Type M10 x 1 Armor Option Armored probe design Minimum Unthreaded Length 0 mm Overall Case Length 80 mm Total Length 9.0 meters (29.5 feet) Cable Type Miniature coaxial ClickLoc connector standard cable Connector Option ClickLoc miniature coaxial connector Agency Approvals CSA, ATEX, IECEx Tariff Code 8537101190 Eddy-Current Probe Scaling and Rotor Dynamics Measurement The 330104-00-08-90-02-05 uses the Bently Nevada 3300 XL 8 mm probe configuration for non-contact displacement measurement. Therefore, the probe generates proportional eddy-current signals that correspond to shaft position changes relative to the probe tip. The probe system requires correct scaling between probe output voltage and mechanical displacement. Additionally, technicians validate gap voltage conditions during installation to maintain measurement accuracy, with typical Bently Nevada systems using -10 VDC target gap voltage references. The armored cable construction provides mechanical protection for installations where routing conditions require additional cable shielding. Furthermore, the miniature coaxial ClickLoc connector maintains signal continuity between the probe and compatible Proximitor Sensor modules. The probe supports rotor dynamics analysis by providing shaft vibration and position data required by Bently Nevada machinery monitoring platforms. Moreover, the probe design incorporates signal conditioning characteristics that support cross-talk suppression in multi-channel monitoring installations. Frequently Asked Questions Q: What measurement technology does the Bently Nevada 330104-00-08-90-02-05 use?A: The probe uses eddy-current technology to measure shaft displacement without physical contact between the probe tip and the rotating surface. Q: What is the function of the -10 VDC gap voltage reference during installation?A: The gap voltage reference verifies the probe installation position and confirms that the probe operates within the specified linear measurement range. Q: Can the 330104-00-08-90-02-05 operate directly without a Proximitor Sensor?A: No. The proximity probe requires a compatible Bently Nevada Proximitor Sensor to provide excitation, signal conversion, and output conditioning. Field Installation Guidelines Install the 330104-00-08-90-02-05 probe using the specified M10 x 1 threaded mounting interface. Ensure that the probe tip faces the monitored shaft surface with correct mechanical alignment. Route the miniature coaxial cable away from high-current conductors, switching power sources, and strong electromagnetic interference areas. Maintain proper cable support to prevent mechanical stress on the connector and armored section. Connect the probe system according to the applicable Bently Nevada 3300 XL installation documentation. Verify the probe gap voltage before commissioning and confirm signal stability during shaft rotation. For multi-probe installations, separate parallel signal paths where possible to reduce electromagnetic coupling effects. Ensure that cable shielding and grounding follow the machinery monitoring system installation requirements.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330101-00-20-10-02-CN 3300 XL 8 mm Proximity Probe
Bently Nevada 330101-00-20-10-02-CN 3300 XL 8 mm Proximity Probe The Bently Nevada 330101-00-20-10-02-CN, also cataloged as the 330101 3300 XL 8 mm Proximity Probe, operates as a dedicated hardware component for shaft displacement measurement within the 3300 XL Proximity Transducer System. Hardware Specifications Parameter Specification Model 330101-00-20-10-02-CN Brand Bently Nevada Product Type 3300 XL 8 mm Proximity Probe Origin USA Weight 0.05 kg Dimensions Estimated shipping size: 1.6 x 1.3 x 112 cm Power Consumption Passive probe element, powered by compatible Proximitor Sensor Thread Type 3/8-24 UNF thread Probe Construction Armored design Unthreaded Length 0.0 in Overall Case Length 2.0 in Total Length 1.0 meter (3.3 feet) Connector Type Miniature coaxial ClickLoc connector standard cable Cable Option Standard cable with miniature coaxial ClickLoc connector Agency Approval CSA, ATEX, IECEx approvals System Compatibility 3300 XL 8 mm Proximity Transducer System Eddy-Current Probe Scaling and Rotor Dynamics Characteristics The Bently Nevada 3300 XL 8 mm Proximity Probe uses eddy-current measurement technology to convert shaft displacement into proportional electrical signals through a compatible Proximitor Sensor. The probe maintains interchangeable mechanical dimensions across 3300 XL 8 mm system components, allowing replacement without individual probe, extension cable, and sensor matching procedures. Additionally, the probe supports rotor dynamics monitoring by providing consistent gap measurement performance for vibration and position analysis. The system uses gap voltage validation with typical -10 VDC target conditions to verify probe operating range and mechanical installation alignment. The probe design incorporates signal stability characteristics required for rotating equipment monitoring. Furthermore, the 3300 XL 8 mm configuration supports API 670 mechanical installation requirements for probe configuration, linear range, accuracy, and temperature stability. Frequently Asked Questions Q: Can the 330101-00-20-10-02-CN probe operate independently without a Proximitor Sensor?A: No. The probe functions as part of the 3300 XL Proximity Transducer System and requires a compatible Proximitor Sensor for signal conditioning and output. Q: What connector configuration does this model use?A: This model uses a miniature coaxial ClickLoc connector with a standard cable configuration. Q: Does the probe require individual calibration with the extension cable and sensor?A: No. The 3300 XL 8 mm system design supports interchangeable probes, extension cables, and Proximitor Sensors within the specified system configuration. Field Installation Guidelines Install the probe using the specified 3/8-24 UNF threaded mounting interface and maintain correct mechanical alignment with the monitored shaft surface. Verify probe gap voltage after installation to confirm the probe operates within the intended measurement range. A typical validation reference uses a -10 VDC gap voltage target. Route the coaxial cable away from high-current power conductors and strong electromagnetic interference sources. Maintain proper cable shielding and grounding practices according to the 3300 XL system installation requirements. Confirm connector engagement at the ClickLoc interface before commissioning the monitoring channel. Inspect the armored section during installation to prevent excessive bending radius stress or mechanical damage.
$200.00 $100.00
-
Bently Nevada 330102-00-40-10-01-05 3300 XL 8 mm Proximity Probe Bently Nevada
Bently Nevada 330102-00-40-10-01-05 3300 XL 8 mm Proximity Probe Configured for shaft displacement measurement in the Bently Nevada 3300 XL Proximity Transducer System, the Bently Nevada 330102-00-40-10-01-05 (330102 3300 XL 8 mm Proximity Probe) provides direct eddy-current sensing output for machinery vibration and position monitoring circuits. Hardware Specifications Parameter Specification Model 330102-00-40-10-01-05 Brand Bently Nevada Product Type 3300 XL 8 mm Proximity Probe Origin USA Weight 0.15 kg Dimensions Estimated shipping size: 1.5 x 1.3 x 117 cm Operating Temp Not specified in provided data Power Consumption Passive eddy-current probe, powered by compatible proximity transducer system Probe Thread 3/8-24 UNF thread Probe Construction Armored probe design Unthreaded Length 0.0 in Overall Case Length 4.0 in Total Length 1.0 meter (3.3 feet) Cable Type Standard cable with miniature coaxial ClickLoc connector and connector protector Agency Approvals CSA, ATEX, IECEx Tariff Code 8537101190 Shipment Location Xiamen, China Eddy-Current Probe Scaling and Gap Voltage Validation The 330102-00-40-10-01-05 uses Bently Nevada 3300 XL eddy-current measurement technology to convert shaft surface movement into electrical displacement signals. The probe operates with compatible proximity sensor electronics that maintain calibrated probe scaling for accurate vibration and position measurement. Furthermore, the system uses gap voltage validation methods during installation. Technicians typically verify probe gap voltage conditions against the -10 VDC target range to confirm correct mechanical positioning between the probe tip and the rotating target surface. The armored construction reduces mechanical damage risks during field installation. In addition, the miniature coaxial ClickLoc connector maintains signal integrity between the probe and extension cable assembly. Frequently Asked Questions Q: What measurement principle does the 330102-00-40-10-01-05 use?A: The probe uses eddy-current sensing technology to measure shaft displacement without physical contact with the rotating target. Q: What connector configuration does this probe include?A: This model includes a miniature coaxial ClickLoc connector with a connector protector and standard cable configuration. Q: Can this probe operate as a standalone measurement device?A: No. The probe requires a compatible Bently Nevada proximity transducer interface to provide power excitation and process the displacement signal. Field Installation Guidelines Install the probe using the specified 3/8-24 UNF threaded mounting interface and verify mechanical alignment before operation. Confirm the probe tip faces the target surface with correct clearance according to the associated Bently Nevada transducer system installation procedure. Check gap voltage during commissioning to verify proper probe positioning and signal response. Route the coaxial cable away from high-current power conductors to minimize electrical interference. Maintain connector cleanliness and ensure the ClickLoc connector is fully secured before system startup. Connect cable shielding according to the machinery monitoring system grounding requirements.
$200.00 $100.00
-
Bently Nevada 330171-12-41-10-02-05 3300 5mm Proximity Probe Bently Nevada
Bently Nevada 330171-12-41-10-02-05 3300 5mm Proximity Probe The Bently Nevada 330171-12-41-10-02-05, also cataloged as the 330171 3300 5mm Proximity Probe, operates as a dedicated hardware component for eddy-current displacement measurement within the 3300 Proximity Transducer System. The probe converts shaft position changes into proportional electrical signals through a compatible 3300 XL Proximitor Sensor and extension cable assembly. Hardware Specifications Parameter Specification Model 330171-12-41-10-02-05 Brand Bently Nevada Product Type 3300 5mm Proximity Probe Origin USA Weight 0.16 kg Dimensions Estimated shipping size: 18 x 18 x 1.5 cm Operating Temp Wide temperature range operation supported by 3300 XL Proximity Transducer System design Power Consumption Passive probe element; powered through connected Proximitor Sensor system Probe Thread Type 1/4-28 UNF thread Armor Option Without armor Unthreaded Length Option 1.2 in Overall Case Length Option 4.1 in Total Length Option 1.0 metre (3.3 feet) Connector Option Miniature coaxial ClickLoc connector standard cable Agency Approval Option Multiple Approvals Measurement Principle Eddy-current non-contact displacement measurement Signal Output Voltage proportional to distance between probe tip and conductive target surface Measurement Application Shaft vibration, shaft position, Keyphasor measurement, speed measurement Eddy-Current Probe Scaling and Rotor Dynamics Monitoring The 330171 series probe uses eddy-current sensing technology to measure conductive target displacement without mechanical contact. The connected Proximitor Sensor scales the probe signal according to the probe tip-to-target gap distance. The system supports rotor dynamics analysis by providing vibration and position data from fluid-film bearing machines. In addition, the probe output maintains signal stability across temperature variations through matched electrical characteristics with compatible 3300 XL extension cables and Proximitor Sensors. The installation process requires gap voltage validation to confirm the operating range. Bently Nevada proximity systems commonly use approximately -10 VDC gap voltage targets for proper probe positioning and signal calibration. Frequently Asked Questions Q: What measurement signals can the 330171-12-41-10-02-05 provide?A: The probe provides displacement-related signals through a connected Proximitor Sensor. The system measures both static shaft position and dynamic vibration signals. Q: Can the 330171-12-41-10-02-05 operate without a Proximitor Sensor?A: No. The probe requires a compatible Proximitor Sensor and extension cable to convert eddy-current measurements into usable voltage output signals. Q: What cable connection does this probe use?A: This configuration uses a miniature coaxial ClickLoc connector with a standard cable assembly. Field Installation Guidelines Install the 1/4-28 UNF threaded probe with correct mechanical engagement to maintain probe alignment with the monitored shaft surface. Maintain proper probe tip clearance from the conductive target area before system calibration. Route the coaxial cable away from high-current conductors and electromagnetic interference sources. Connect cable shielding according to the monitoring system grounding requirements to reduce electrical noise. Verify the probe gap voltage after installation before placing the machinery monitoring channel into service. Avoid mechanical damage to the probe tip, connector interface, and cable jacket during installation. Confirm compatibility between the probe, extension cable, and Proximitor Sensor before commissioning.
$200.00 $100.00
-
Bently Nevada Bently Nevada 330190-085-00-05 3300 XL ETR Extension Cable
Bently Nevada 330190-085-00-05 3300 XL ETR Extension Cable Configured for high-temperature signal transmission in the 3300 XL 8 mm Proximity Transducer System, the Bently Nevada 330190-085-00-05 (330190 3300 XL ETR Extension Cable) provides direct electrical connection between the proximity probe and Proximitor Sensor. Hardware Specifications Parameter Specification Model 330190-085-00-05 Brand Bently Nevada Product Type 3300 XL Extended Temperature Range (ETR) Extension Cable Origin USA Weight 0.25 kg Dimensions 20 x 20 x 2.5 cm estimated shipping size Cable Length 8.5 meters (27.9 feet) Cable Type Standard cable Cable Impedance 75 Ohm triaxial cable Operating Temp Extension cable rated up to 260 deg C (500 deg F) Power Consumption Passive cable component, no external power consumption System Compatibility 3300 XL 8 mm Proximity Transducer System Probe Compatibility Standard and Extended Temperature Range (ETR) probes Agency Approvals CSA, ATEX, IECEx Tariff Code 8537101190 Shipment Location Xiamen, China Eddy-Current Signal Transmission and Rotor Dynamics Monitoring The 330190-085-00-05 maintains the electrical signal path between the 3300 XL 8 mm probe and the 3300 XL Proximitor Sensor. Therefore, the system converts probe gap distance into proportional output voltage for shaft position and vibration measurements. The ETR extension cable supports applications where cable exposure exceeds the standard 177 deg C temperature specification. In addition, the cable construction allows operation with ETR probes rated up to 218 deg C and cable temperature exposure up to 260 deg C. The 3300 XL system uses eddy-current measurement technology to monitor conductive shaft targets. Furthermore, the transducer chain supports rotor dynamics analysis, radial vibration monitoring, axial position measurement, and Keyphasor reference signals. The system requires proper eddy-current probe scaling and gap voltage validation during commissioning. The standard operating target for probe gap voltage validation is typically -10 VDC, which confirms the probe operating range and signal conditioning accuracy. Frequently Asked Questions Q: Can the 330190-085-00-05 operate with standard 3300 XL Proximitor Sensors?A: Yes. The ETR extension cable uses the standard 3300 XL signal interface and operates with compatible 3300 XL Proximitor Sensors. Q: What temperature limitation applies to the 330190-085-00-05 cable?A: The extension cable supports temperatures up to 260 deg C (500 deg F). The total system accuracy is limited by the ETR component specifications when ETR components are installed. Q: Can this cable replace existing 3300 series extension cables?A: The cable is interchangeable within compatible 3300 XL 8 mm systems and supports upgrades or replacements in existing installations when system configuration requirements are met. Field Installation Guidelines Install the extension cable according to the 3300 XL Proximity Transducer System wiring requirements. Maintain separation between the transducer cable and high-current power conductors to reduce electrical interference. Connect cable shielding according to the system grounding specification to minimize signal noise. Avoid sharp bending, mechanical stress, and excessive pulling force during cable routing. Verify probe, extension cable, and Proximitor Sensor compatibility before commissioning. Perform gap voltage validation after installation to confirm correct probe positioning and signal operation.
$200.00 $100.00
-
Bently Nevada 330130-040-12-CN 3300 XL Extension Cable | Bently Nevada
Bently Nevada 330130-040-12-CN 3300 XL Extension Cable The Bently Nevada 330130-040-12-CN, also cataloged as the 330130 3300 XL Extension Cable, operates as a dedicated hardware component for eddy-current probe signal extension within the Bently Nevada 3300 XL Proximity Transducer System. Hardware Specifications Parameter Specification Model 330130-040-12-CN Brand Bently Nevada Product Type 3300 XL Extension Cable Origin USA Weight 0.034 kg Dimensions Not specified Operating Temp -51 deg C to +177 deg C (-60 deg F to +351 deg F) Power Consumption Passive cable component, no external power consumption Cable Length 4.0 meters (13.1 feet) Cable Construction 75 ohm triaxial, FEP insulated cable Cable Option FluidLoc cable with connector protectors Connector Protection Integrated connector protectors Probe Cable Compatibility Supports 0.5 m, 1 m, 1.5 m, 2 m, 5 m, and 9 m total probe length configurations Agency Approval CN approval option for country-specific requirements Eddy-Current Signal Extension and Rotor Dynamics Interface The 330130-040-12-CN extension cable transfers eddy-current probe signals between the proximity probe and the Proximitor sensor module in the 3300 XL transducer chain. The 75 ohm triaxial FEP insulated construction maintains signal characteristics for shaft displacement and vibration measurement circuits. Furthermore, the cable design supports Bently Nevada eddy-current probe scaling requirements by maintaining stable impedance characteristics across the measurement path. Proper cable selection helps preserve gap voltage validation performance, including typical -10 VDC target gap reference conditions used during proximity system calibration. The FluidLoc cable option provides additional protection against fluid migration along the cable structure. Additionally, the connector protector design reduces mechanical stress at connection points during field installation. Frequently Asked Questions Q: Does the 330130-040-12-CN cable require external power supply?A: No. The 330130-040-12-CN is a passive extension cable and does not consume electrical power. It transfers the proximity probe signal between connected Bently Nevada transducer components. Q: What cable construction does the 330130-040-12-CN use?A: The cable uses a 75 ohm triaxial FEP insulated construction designed for eddy-current proximity measurement signal transmission. Q: Can the 330130-040-12-CN be installed with different probe length configurations?A: Yes. The cable supports 3300 XL probe system configurations using total probe lengths of 0.5 m, 1 m, 1.5 m, 2 m, 5 m, or 9 m according to system configuration requirements. Field Installation Guidelines Install the 330130-040-12-CN cable according to the Bently Nevada 3300 XL proximity system wiring requirements. Route the extension cable away from high-current power cables and strong electromagnetic interference sources. Maintain proper cable bending practices to prevent damage to the triaxial shielding structure. Verify connector cleanliness before mating the cable with the probe and Proximitor sensor. Confirm shield continuity and grounding practices follow the installed monitoring system requirements. Avoid unnecessary cable loops near rotating equipment to reduce mechanical stress and signal disturbance. Verify gap voltage readings after installation to confirm correct proximity probe operating conditions.
$200.00 $100.00
Anda telah melihat 24 dari 582 produk