{"product_id":"ethernet-communication-module-yokogawa-ale111-s01","title":"Ethernet Communication Module | Yokogawa ALE111-S01","description":"\u003ch2\u003eYokogawa ALE111-S01 Ethernet Communication Module\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eYokogawa ALE111-S01\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eALE111\u003c\/strong\u003e Ethernet Communication Module, operates as a dedicated hardware component for deterministic data exchange between CENTUM VP distributed control systems and external subsystem controllers via standard Ethernet infrastructure.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eParameter\u003c\/th\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel Brand\u003c\/td\u003e\n\u003ctd\u003eYokogawa\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eJapan\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.30 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 to 50 degC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e0.50 A @ 5 VDC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInterface Type\u003c\/td\u003e\n\u003ctd\u003e100Base-TX \/ 10Base-T\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConnector\u003c\/td\u003e\n\u003ctd\u003eRJ-45 x 1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTransmission Speed\u003c\/td\u003e\n\u003ctd\u003e100 Mbps \/ 10 Mbps (auto-sensing)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTransmission Distance\u003c\/td\u003e\n\u003ctd\u003eMax. 100 m\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTransmission Medium\u003c\/td\u003e\n\u003ctd\u003eCat 5 or higher UTP cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSupported Protocols\u003c\/td\u003e\n\u003ctd\u003eModbus\/TCP, MELSEC, PLC-5\/SLC500, Omron FINS\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRedundancy Support\u003c\/td\u003e\n\u003ctd\u003eDual-redundant configuration possible\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMax Connections\u003c\/td\u003e\n\u003ctd\u003eUp to 4 per module (protocol dependent)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProcess Control Network Characteristics\u003c\/h3\u003e\n\u003cp\u003eThis module supports 4-20 mA HART loop protocol translation when interfacing analog input\/output subsystems through Ethernet encapsulation. Channel-to-channel isolation is maintained to prevent ground loop formation between control nodes. Cold junction compensation is applied in connected temperature measurement subsystems to ensure signal accuracy under varying ambient conditions.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eQ:\u003c\/strong\u003e Does the ALE111-S01 support hot-swapping?\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eA:\u003c\/strong\u003e Yes, when installed in a redundant pair within supported node units, the module can be replaced without interrupting network communications.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ:\u003c\/strong\u003e What is the switching behavior during redundancy failover?\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eA:\u003c\/strong\u003e Communication switchover occurs at the network stack level with no controller-side interruption; however, protocol session re-establishment timing depends on the connected subsystem firmware.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ:\u003c\/strong\u003e Are there any backplane power restrictions?\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eA:\u003c\/strong\u003e The module requires 5 VDC from the node unit backplane with a maximum draw of 0.50 A; exceeding this may cause voltage drop faults in adjacent modules.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cp\u003eInstall the ALE111-S01 only in designated ESB or ER bus node unit slots. Use shielded Category 5e or higher UTP cables for runs near high-power equipment to minimize electromagnetic interference. Terminate cable shields at both ends to the node unit ground bus. Verify RJ-45 latch integrity before commissioning. When deploying in redundant configuration, synchronize firmware revisions between both modules to prevent communication handshake errors.\u003c\/p\u003e","brand":"Yokogawa","offers":[{"title":"Default Title","offer_id":44209043538008,"sku":"ALE111-S01","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0670\/2039\/0488\/files\/ALE111-S01.jpg?v=1780973615","url":"https:\/\/www.industriaxplc.com\/products\/ethernet-communication-module-yokogawa-ale111-s01","provider":"IndustriaX Limited","version":"1.0","type":"link"}