{"product_id":"ge-ds200pccag7acb-mark-v-power-connect-card","title":"GE DS200PCCAG7ACB Mark V Power Connect Card","description":"\u003ch2\u003eGE DS200PCCAG7ACB Mark V Power Connect Card\u003c\/h2\u003e\n\u003cp\u003eConfigured for DC power distribution and signal interfacing in Mark V Turbine Control platforms, the \u003cstrong\u003eGE DS200PCCAG7ACB\u003c\/strong\u003e (\u003cstrong\u003eDS200PCCA\u003c\/strong\u003e Power Connect Card) provides direct physical\/electrical execution. It establishes the power interface between the DC2000 drive chassis and the SCR power bridge, regulating local DC lines and providing snubber protection.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDS200PCCAG7ACB\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGE (General Electric)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e1.70 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e280 mm x 80 mm x 25 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-20 to +65 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003ePassive distribution board; loss determined by load current and onboard resistor dissipation\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNominal Input Voltage\u003c\/td\u003e\n\u003ctd\u003e125 VDC nominal (100-150 VDC operating range)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutput Configuration\u003c\/td\u003e\n\u003ctd\u003e6 fused DC outputs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eChannel Current Capacity\u003c\/td\u003e\n\u003ctd\u003e10 A maximum per channel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOvercurrent Protection\u003c\/td\u003e\n\u003ctd\u003e10 A fast-blow fuses, field-replaceable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMechanical Integration\u003c\/td\u003e\n\u003ctd\u003eCompatible with C-frame and G-frame power supply assemblies\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePCB Coating\u003c\/td\u003e\n\u003ctd\u003eConformal coated FR4 laminate\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eEdge Interfaces\u003c\/td\u003e\n\u003ctd\u003e2 x 32-pin card-edge connectors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eBackplane Bus Communication and Hardware Compatibility\u003c\/h3\u003e\n\u003cp\u003eThe DS200PCCAG7ACB operates within the internal power bus architecture of the GE DC2000 drive and Mark V turbine control framework. Power distribution lines pass through onboard filtering circuits equipped with 12 precision wire-wound resistors, 6 discrete suppression diodes, and 6 individual protection fuses. The board provides deterministic signal pass-through and power bus decoupling without introducing communication latencies to the drive controller. Firmware flash compatibility is governed by the host controller revision, while hardware revision G7 specifies exact voltage rating limits, snubber network impedances, and frame-style alignment for drive backplanes.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: What indicates an overcurrent trip on a specific channel, and can fuses be serviced live?\u003c\/p\u003e\n\u003cp\u003eA: An open line condition is identified by checking continuity across the individual 10 A fast-blow fuses on the board face. Fuses must not be replaced while the 125 VDC bus is energized. Power to the drive backplane must be completely isolated and verified zero-energy prior to component replacement.\u003c\/p\u003e\n\u003cp\u003eQ: Can the DS200PCCAG7ACB be installed in place of earlier Group (G1-G6) cards?\u003c\/p\u003e\n\u003cp\u003eA: No. Group designations dictate specific snubber network values, voltage clamping levels, and mechanical layout constraints for designated frame sizes (such as C-style or G-style frames). Installing an mismatched group variant can result in incorrect snubber response and damage to the SCR power bridge.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower Isolation:\u003c\/strong\u003e De-energize the main 125 VDC supply and auxiliary drive control power. Discharge all power bridge bus capacitors and verify zero voltage using a calibrated multimeter before touching the card assembly.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eESD Precautions:\u003c\/strong\u003e Connect an ESD grounding wrist strap to a verified frame ground point prior to removing the replacement board from its anti-static packaging.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMechanical Alignment:\u003c\/strong\u003e Align the card along the chassis guide rails. Slide the board inward until the dual 32-pin edge connectors sit flush with the backplane receptacles, applying even pressure across the PCB edge to prevent pin deformation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWiring and Fusing Verification:\u003c\/strong\u003e Ensure all 6 field-replaceable 10 A fast-blow fuses are properly seated in their holders. Verify that all external terminal connections match the wiring diagrams in GEI-100161.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrounding:\u003c\/strong\u003e Verify continuous frame ground bonding through the card mounting hardware to maintain effective noise suppression across the onboard snubber network.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":44476752822360,"sku":"DS200PCCAG7ACB","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0670\/2039\/0488\/files\/DS200PCCAG1ADB1.jpg?v=1785317121","url":"https:\/\/www.industriaxplc.com\/id\/products\/ge-ds200pccag7acb-mark-v-power-connect-card","provider":"IndustriaX Limited","version":"1.0","type":"link"}