{"product_id":"ge-ds200pccag6acb-power-connect-board","title":"GE DS200PCCAG6ACB Power Connect Board","description":"\u003ch2\u003eGE DS200PCCAG6ACB Power Connect Board\u003c\/h2\u003e\n\u003cp\u003eConfigured for DC power distribution and signal interconnection in GE Mark V Speedtronic turbine control platforms, the \u003cstrong\u003eGeneral Electric DS200PCCAG6ACB\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eDS200PCCAG6A\u003c\/strong\u003e Power Connect Card, provides direct physical and electrical execution across drive power networks.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDS200PCCAG6ACB\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric (GE)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.68 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e240 mm x 160 mm x 1.6 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 to 55 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e24 VDC nominal input\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Outputs\u003c\/td\u003e\n\u003ctd\u003eRegulated 5 VDC, 12 VDC, 24 VDC rails\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCurrent Capacity\u003c\/td\u003e\n\u003ctd\u003e5 A total distributed\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCircuit Protection\u003c\/td\u003e\n\u003ctd\u003e2 x 5 A input fuses\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDiagnostic Interface\u003c\/td\u003e\n\u003ctd\u003e3 Status LEDs (PWR, 5V OK, 12V OK), 8 gold-plated test points\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMounting Type\u003c\/td\u003e\n\u003ctd\u003e4 x M4 screw standoffs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eSystem Connectivity \u0026amp; Backplane Bus Integrity\u003c\/h3\u003e\n\u003cp\u003eThe DS200PCCAG6ACB maintains backplane bus communication velocity and power delivery across Mark V drive architectures. Designed with multi-channel galvanic isolation and noise-suppression networks, the board mitigates cross-talk and high-frequency switching EMI emitted from high-power silicon-controlled rectifier (SCR) bridges. Integrated firmware flash compatibility across board revisions guarantees deterministic signal routing between central processing engines and peripheral gate drivers.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: What action should be taken if the board loses power output while 24 VDC input remains active?\u003c\/p\u003e\n\u003cp\u003eA: Inspect the two integrated 5 A input fuses on the PCB surface for open-circuit conditions using a digital multimeter. Verify that downstream loads on the 5 VDC, 12 VDC, and 24 VDC distribution lines do not present a direct short circuit to ground before replacing fuses.\u003c\/p\u003e\n\u003cp\u003eQ: Can the DS200PCCAG6ACB board be hot-swapped while the Mark V control rack is powered on?\u003c\/p\u003e\n\u003cp\u003eA: No. Hot-swapping the power connect card risks arcing across the 20-pin header contacts and damaging sensitive gate driver components. De-energize all primary 24 VDC feed lines and wait until all diagnostic LEDs fully discharge before performing maintenance.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cp\u003eEnsure all system power feeds are locked out and tagged before handling the module. Standard electrostatic discharge (ESD) precautionary measures must be followed, including grounding wrist-straps attached to an unpainted metal chassis ground.\u003c\/p\u003e\n\u003cp\u003eMount the circuit board securely onto the designated enclosure plate using four M4 threaded metal standoffs, taking care not to warp the FR-4 substrate. Verify that all 20-pin terminal ribbon connectors are fully seated with locking clips engaged. Maintain separation between high-voltage power leads and low-voltage signal cabling within wire trays to prevent inductive noise coupling.\u003c\/p\u003e","brand":"General Electric","offers":[{"title":"Default Title","offer_id":44476750626904,"sku":"DS200PCCAG6ACB","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0670\/2039\/0488\/files\/DS200PCCAG1ADB.jpg?v=1785317121","url":"https:\/\/www.industriaxplc.com\/ar\/products\/ge-ds200pccag6acb-power-connect-board","provider":"IndustriaX Limited","version":"1.0","type":"link"}