{"product_id":"3300-xl-8-mm-proximity-probe-bently-nevada-330101-00-12-10-02-05","title":"3300 XL 8 mm Proximity Probe | Bently Nevada 330101-00-12-10-02-05","description":"\u003ch2\u003eBently Nevada 330101-00-12-10-02-05 3300 XL 8 mm Proximity Probe\u003c\/h2\u003e\n\u003cp\u003eConfigured for radial vibration and thrust position measurement in Bently Nevada 3300 XL Transducer Systems, the \u003cstrong\u003eBently Nevada 330101-00-12-10-02-05\u003c\/strong\u003e (base model \u003cstrong\u003e330101\u003c\/strong\u003e proximity probe) provides direct eddy-current displacement sensing for rotating machinery shafts. It interfaces physically with matching extension cables and drivers to generate proportional DC voltage outputs tied to target surface position.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eParameter\u003c\/th\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eBently Nevada\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.1 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e1.5 x 1.2 x 113 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-34 to 177 degC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003ePassive sensor; powered via driver\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eThread Type\u003c\/td\u003e\n\u003ctd\u003e3\/8-24 UNF\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eUnthreaded Length\u003c\/td\u003e\n\u003ctd\u003e0.0 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOverall Case Length\u003c\/td\u003e\n\u003ctd\u003e1.2 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTotal Length\u003c\/td\u003e\n\u003ctd\u003e1.0 m (3.3 ft)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConnector Type\u003c\/td\u003e\n\u003ctd\u003eMiniature coaxial ClickLoc connector\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAgency Approvals\u003c\/td\u003e\n\u003ctd\u003eCSA, ATEX, IECEx\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eEddy-Current Probe Scaling and Gap Voltage Validation\u003c\/h3\u003e\n\u003cp\u003eThe 330101 series probes operate on eddy-current induction principles where probe tip impedance changes linearly with target distance. Scaling is fixed at 7.87 mV\/μm (200 mV\/mil) over the linear range. Gap voltage validation targets -10 VDC when measuring against a steel target at mid-range. Cross-talk suppression is achieved through phase-matched cable pairing and precise shield termination practices per Bently Nevada installation manuals.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can this probe be used without armor in high-vibration environments?\u003c\/p\u003e\n\u003cp\u003eA: Yes, but routing must avoid sharp bends and mechanical impact zones to prevent cable fatigue failure.\u003c\/p\u003e\n\u003cp\u003eQ: Is hot-swapping supported between probe and driver electronics?\u003c\/p\u003e\n\u003cp\u003eA: No. System power must be removed before disconnecting or connecting probes to prevent transient damage.\u003c\/p\u003e\n\u003cp\u003eQ: What is the minimum bending radius for the standard cable?\u003c\/p\u003e\n\u003cp\u003eA: Maintain a bend radius no less than 25 mm to preserve signal integrity.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cp\u003eMount the probe using the 3\/8-24 UNF threads into a rigid bracket. Ensure at least five full threads engagement for vibration resistance. Terminate the shield at the driver end only to maintain single-point grounding and reduce EMI pickup. Verify gap voltage before final system commissioning using a calibrated driver interface. Avoid routing probe cables parallel to high-power AC conductors.\u003c\/p\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":44266244407384,"sku":"330101-00-12-10-02-05","price":100.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0670\/2039\/0488\/files\/330101-00-12-10-02-05-3.jpg?v=1782116335","url":"https:\/\/www.industriaxplc.com\/ar\/products\/3300-xl-8-mm-proximity-probe-bently-nevada-330101-00-12-10-02-05","provider":"IndustriaX Limited","version":"1.0","type":"link"}